ERROR: too many flash sectors
Hi , everyone .
My u-boot version is 2009-01 and i try porting u-boot on pxa270 development board.
when i power on my board then minicom show these information
DRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectors
Flash: 32 MB
then i can save setenv , but when i earse my flash ,it cause one error
Error: end address not on sector boundary
and here is my flinfo :
Bank # 1: CFI conformant FLASH (32 x 16) Size: 32 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18 Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 64 bytes
Sector Start Addresses:
00000000 RO 00040000 RO 00080000 RO 000C0000 RO 00100000
RO
etc...
And i dont know my network chip work or not . ( my chip is LAN91C113 ) when i ping some address , it show
ethid=0000...
LAN91C113:PHY auto-negotiate timed out
then my bootloader freeze ....
would someone can help me ? thanks.
Signature · 2 lines
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors-tp25063511p25063511.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Quoted 9 lines · On Thursday 20 August 2009 16:45:28 SlinceArm wrote:
Hi , everyone .
My u-boot version is 2009-01 and i try porting u-boot on pxa270 development board.
when i power on my board then minicom show these informationDRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectors
This error is important. Searching in the source code gives you an hint. You should increase CONFIG_SYS_MAX_FLASH_SECT to match you hardware.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
Quoted 7 lines · Stefan Roese
Quoted 7 lines
DRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectorsQuoted 1 line
This error is important. Searching in the source code gives you an hint.
You
Quoted 6 lines
Quoted 4 lines
Quoted 4 lines
should increase
CONFIG_SYS_MAX_FLASH_SECTto match you hardware.Cheers,
Stefan
Quoted 13 lines · Stefan Roese
Quoted 10 lines · On Thursday 20 August 2009 16:45:28 SlinceArm wrote:
Hi , everyone .
My u-boot version is 2009-01 and i try porting u-boot on pxa270 development
board.
when i power on my board then minicom show these informationDRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectors
Quoted 7 lines
This error is important. Searching in the source code gives you an hint. You
should increaseCONFIG_SYS_MAX_FLASH_SECTto match you hardware.Cheers,
Stefan
Thanks for your reply , Stefan. : )
My flash is 32MB
and here is my source code for flash environment
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_FLASH_CFI_WIDTH FLASH_CFI_32BIT
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 128
What code did set wrong ??
Signature · 2 lines
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors-tp25063511p25090177.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Penda
Quoted 51 lines
Quoted 7 lines · Stefan Roese
Quoted 7 lines
DRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectorsQuoted 1 line
This error is important. Searching in the source code
gives you an hint.
YouQuoted 6 lines
Quoted 4 lines
Quoted 4 lines
should increase
CONFIG_SYS_MAX_FLASH_SECTto match you hardware.Cheers,
StefanQuoted 9 lines · Stefan Roese
Quoted 7 lines · On Thursday 20 August 2009 16:45:28 SlinceArm wrote:
Hi , everyone .
My u-boot version is 2009-01 and i try porting u-boot on pxa270 development
board.
when i power on my board then minicom show these informationQuoted 5 lines
Quoted 3 lines
DRAM: 64 MB
ERROR: too many flash sectors
ERROR: too many flash sectorsThis error is important. Searching in the source code gives
you an hint.
Quoted 6 lines
You
should increaseCONFIG_SYS_MAX_FLASH_SECTto match you hardware.Cheers,
StefanThanks for your reply , Stefan. : )
My flash is 32MB
Quoted 8 lines
and here is my source code for flash environment
#define
CONFIG_SYS_FLASH_CFI
#defineCONFIG_FLASH_CFI_DRIVER1
#defineCONFIG_FLASH_CFI_WIDTHFLASH_CFI_32BIT#define
CONFIG_SYS_MAX_FLASH_BANKS1
#defineCONFIG_SYS_MAX_FLASH_SECT128
Please check your sector size CONFIG_SYS_ENV_SECT_SIZE and multiply with your CONFIG_SYS_MAX_FLASH_SECT should not cross 32MB
Quoted 14 lines
What code did set wrong ??
Signature · 9 lines
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors -tp25063511p25090177.html Sent from the Uboot - Users mailing list archive at Nabble.com. _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Quoted 6 lines · On Saturday 22 August 2009 04:58:44 SlinceArm wrote:
Thanks for your reply , Stefan. : )
My flash is 32MB
and here is my source code for flash environment
Quoted 8 lines
#define
CONFIG_SYS_FLASH_CFI
#defineCONFIG_FLASH_CFI_DRIVER1
#defineCONFIG_FLASH_CFI_WIDTHFLASH_CFI_32BIT#define
CONFIG_SYS_MAX_FLASH_BANKS1
#defineCONFIG_SYS_MAX_FLASH_SECT128What code did set wrong ??
As I already mentioned, the CONFIG_SYS_MAX_FLASH_SECT value is too low. I suggest you increase it to 512 and give it another try.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
Quoted 23 lines · Stefan Roese
Quoted 6 lines · On Saturday 22 August 2009 04:58:44 SlinceArm wrote:
Thanks for your reply , Stefan. : )
My flash is 32MB
and here is my source code for flash environment
Quoted 8 lines
#define
CONFIG_SYS_FLASH_CFI
#defineCONFIG_FLASH_CFI_DRIVER1
#defineCONFIG_FLASH_CFI_WIDTHFLASH_CFI_32BIT#define
CONFIG_SYS_MAX_FLASH_BANKS1
#defineCONFIG_SYS_MAX_FLASH_SECT128What code did set wrong ??
As I already mentioned, the
CONFIG_SYS_MAX_FLASH_SECTvalue is too low. I suggest you increase it to 512 and give it another try.Cheers,
Stefan
Quoted 10 lines
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
thaks your reply, Stefan .
i follow your suggestion .
increase the CONFIG_SYS_MAX_FLASH_SECT to 256.
and the Error is fixed . : )
Thanks your suggestion.
Signature · 2 lines
View this message in context: http://www.nabble.com/-U-Boot--ERROR%3A-too-many-flash-sectors-tp25063511p25117245.html Sent from the Uboot - Users mailing list archive at Nabble.com.