Skip to contentSkip to conversation

mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order

PATCH In review Marek Vasut 3 participants 3 messages May 13, 2023 – May 24, 2023 MMC, SD and SDIO

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order

Chapter "5.3 Power-Up/Down Sequence" of WILC1000 [1] and WILC3000 [2] states that CHIP_EN must be pulled HIGH first, RESETN second. Fix the order of these signals in the driver.

Use the mmc_pwrseq_ops as driver data as the delay between signals is specific to SDIO card type anyway.

[1] https://ww1.microchip.com/downloads/aemDocuments/documents/WSG/ProductDocuments/DataSheets/ATWILC1000-MR110XB-IEEE-802.11-b-g-n-Link-Controller-Module-DS70005326E.pdf
[2] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/IEEE-802.11-b-g-n-Link-Controller-Module-with-Integrated-Bluetooth-5.0-DS70005327B.pdf

Fixes b2832b96fcf5 ("mmc: pwrseq: sd8787: add support for wilc1000")

---
Cc: Ajay Singh <[email protected]>
Cc: Claudiu Beznea <[email protected]>
Cc: Ulf Hansson <[email protected]>
Cc: [email protected]

---
 drivers/mmc/core/pwrseq_sd8787.c | 34 ++++++++++++++++++++++++--------
 1 file changed, 26 insertions(+), 8 deletions(-)
drivers/mmc/core/pwrseq_sd8787.c +26 -8
index 2e120ad83020f..0c5f5e371e1f8 100644
@@ -28,7 +28,6 @@ struct mmc_pwrseq_sd8787 {
 	struct mmc_pwrseq pwrseq;
 	struct gpio_desc *reset_gpio;
 	struct gpio_desc *pwrdn_gpio;
-	u32 reset_pwrdwn_delay_ms;
 };
 
 #define to_pwrseq_sd8787(p) container_of(p, struct mmc_pwrseq_sd8787, pwrseq)
@@ -39,7 +38,7 @@ static void mmc_pwrseq_sd8787_pre_power_on(struct mmc_host *host)
 
 	gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
 
-	msleep(pwrseq->reset_pwrdwn_delay_ms);
+	msleep(300);
 	gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
 }
 
@@ -51,17 +50,37 @@ static void mmc_pwrseq_sd8787_power_off(struct mmc_host *host)
 	gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
 }
 
+static void mmc_pwrseq_wilc1000_pre_power_on(struct mmc_host *host)
+{
+	struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+	/* The pwrdn_gpio is really CHIP_EN, reset_gpio is RESETN */
+	gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
+	msleep(5);
+	gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
+}
+
+static void mmc_pwrseq_wilc1000_power_off(struct mmc_host *host)
+{
+	struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+	gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
+	gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 0);
+}
+
 static const struct mmc_pwrseq_ops mmc_pwrseq_sd8787_ops = {
 	.pre_power_on = mmc_pwrseq_sd8787_pre_power_on,
 	.power_off = mmc_pwrseq_sd8787_power_off,
 };
 
-static const u32 sd8787_delay_ms = 300;
-static const u32 wilc1000_delay_ms = 5;
+static const struct mmc_pwrseq_ops mmc_pwrseq_wilc1000_ops = {
+	.pre_power_on = mmc_pwrseq_wilc1000_pre_power_on,
+	.power_off = mmc_pwrseq_wilc1000_power_off,
+};
 
 static const struct of_device_id mmc_pwrseq_sd8787_of_match[] = {
-	{ .compatible = "mmc-pwrseq-sd8787", .data = &sd8787_delay_ms },
-	{ .compatible = "mmc-pwrseq-wilc1000", .data = &wilc1000_delay_ms },
+	{ .compatible = "mmc-pwrseq-sd8787", .data = &mmc_pwrseq_sd8787_ops },
+	{ .compatible = "mmc-pwrseq-wilc1000", .data = &mmc_pwrseq_wilc1000_ops },
 	{/* sentinel */},
 };
 MODULE_DEVICE_TABLE(of, mmc_pwrseq_sd8787_of_match);
@@ -77,7 +96,6 @@ static int mmc_pwrseq_sd8787_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	match = of_match_node(mmc_pwrseq_sd8787_of_match, pdev->dev.of_node);
-	pwrseq->reset_pwrdwn_delay_ms = *(u32 *)match->data;
 
 	pwrseq->pwrdn_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_LOW);
 	if (IS_ERR(pwrseq->pwrdn_gpio))
@@ -88,7 +106,7 @@ static int mmc_pwrseq_sd8787_probe(struct platform_device *pdev)
 		return PTR_ERR(pwrseq->reset_gpio);
 
 	pwrseq->pwrseq.dev = dev;
-	pwrseq->pwrseq.ops = &mmc_pwrseq_sd8787_ops;
+	pwrseq->pwrseq.ops = match->data;
 	pwrseq->pwrseq.owner = THIS_MODULE;
 	platform_set_drvdata(pdev, pwrseq);
 
Signature · 1 line
2.39.2
Reviewed-by on v1 1/1
#1 lore raw
Quoted 6 lines · Marek Vasut

EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe

Chapter "5.3 Power-Up/Down Sequence" of WILC1000 [1] and WILC3000 [2] states that CHIP_EN must be pulled HIGH first, RESETN second. Fix the order of these signals in the driver.

Quoted 8 lines

Use the mmc_pwrseq_ops as driver data as the delay between signals is specific to SDIO card type anyway.

[1] https://ww1.microchip.com/downloads/aemDocuments/documents/WSG/ProductDocuments/DataSheets/ATWILC1000-MR110XB-IEEE-802.11-b-g-n-Link-Controller-Module-DS70005326E.pdf
[2] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/IEEE-802.11-b-g-n-Link-Controller-Module-with-Integrated-Bluetooth-5.0-DS70005327B.pdf

Fixes b2832b96fcf5 ("mmc: pwrseq: sd8787: add support for wilc1000")
Quoted 92 lines

---
Cc: Ajay Singh <[email protected]>
Cc: Claudiu Beznea <[email protected]>
Cc: Ulf Hansson <[email protected]>
Cc: [email protected]

---
 drivers/mmc/core/pwrseq_sd8787.c | 34 ++++++++++++++++++++++++--------
 1 file changed, 26 insertions(+), 8 deletions(-)
drivers/mmc/core/pwrseq_sd8787.c +26 -9
index 2e120ad83020f..0c5f5e371e1f8 100644
@@ -28,7 +28,6 @@ struct mmc_pwrseq_sd8787 {
        struct mmc_pwrseq pwrseq;
        struct gpio_desc *reset_gpio;
        struct gpio_desc *pwrdn_gpio;
-       u32 reset_pwrdwn_delay_ms;
 };
 
 #define to_pwrseq_sd8787(p) container_of(p, struct mmc_pwrseq_sd8787, pwrseq)
@@ -39,7 +38,7 @@ static void mmc_pwrseq_sd8787_pre_power_on(struct mmc_host *host)
 
        gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
 
-       msleep(pwrseq->reset_pwrdwn_delay_ms);
+       msleep(300);
        gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
 }
 
@@ -51,17 +50,37 @@ static void mmc_pwrseq_sd8787_power_off(struct mmc_host *host)
        gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
 }
 
+static void mmc_pwrseq_wilc1000_pre_power_on(struct mmc_host *host)
+{
+       struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+       /* The pwrdn_gpio is really CHIP_EN, reset_gpio is RESETN */
+       gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
+       msleep(5);
+       gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
+}
+
+static void mmc_pwrseq_wilc1000_power_off(struct mmc_host *host)
+{
+       struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+       gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
+       gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 0);
+}
+
 static const struct mmc_pwrseq_ops mmc_pwrseq_sd8787_ops = {
        .pre_power_on = mmc_pwrseq_sd8787_pre_power_on,
        .power_off = mmc_pwrseq_sd8787_power_off,
 };
 
-static const u32 sd8787_delay_ms = 300;
-static const u32 wilc1000_delay_ms = 5;
+static const struct mmc_pwrseq_ops mmc_pwrseq_wilc1000_ops = {
+       .pre_power_on = mmc_pwrseq_wilc1000_pre_power_on,
+       .power_off = mmc_pwrseq_wilc1000_power_off,
+};
 
 static const struct of_device_id mmc_pwrseq_sd8787_of_match[] = {
-       { .compatible = "mmc-pwrseq-sd8787", .data = &sd8787_delay_ms },
-       { .compatible = "mmc-pwrseq-wilc1000", .data = &wilc1000_delay_ms },
+       { .compatible = "mmc-pwrseq-sd8787", .data = &mmc_pwrseq_sd8787_ops },
+       { .compatible = "mmc-pwrseq-wilc1000", .data = &mmc_pwrseq_wilc1000_ops },
        {/* sentinel */},
 };
 MODULE_DEVICE_TABLE(of, mmc_pwrseq_sd8787_of_match);
@@ -77,7 +96,6 @@ static int mmc_pwrseq_sd8787_probe(struct platform_device *pdev)
                return -ENOMEM;
 
        match = of_match_node(mmc_pwrseq_sd8787_of_match, pdev->dev.of_node);
-       pwrseq->reset_pwrdwn_delay_ms = *(u32 *)match->data;
 
        pwrseq->pwrdn_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_LOW);
        if (IS_ERR(pwrseq->pwrdn_gpio))
@@ -88,7 +106,7 @@ static int mmc_pwrseq_sd8787_probe(struct platform_device *pdev)
                return PTR_ERR(pwrseq->reset_gpio);
 
        pwrseq->pwrseq.dev = dev;
-       pwrseq->pwrseq.ops = &mmc_pwrseq_sd8787_ops;
+       pwrseq->pwrseq.ops = match->data;
        pwrseq->pwrseq.owner = THIS_MODULE;
        platform_set_drvdata(pdev, pwrseq);
 
--

2.39.2

#2 lore raw
In reply to Marek Vasut
Quoted 5 lines · Marek Vasut

Chapter "5.3 Power-Up/Down Sequence" of WILC1000 [1] and WILC3000 [2] states that CHIP_EN must be pulled HIGH first, RESETN second. Fix the order of these signals in the driver.

Quoted 8 lines

Use the mmc_pwrseq_ops as driver data as the delay between signals is specific to SDIO card type anyway.

[1] https://ww1.microchip.com/downloads/aemDocuments/documents/WSG/ProductDocuments/DataSheets/ATWILC1000-MR110XB-IEEE-802.11-b-g-n-Link-Controller-Module-DS70005326E.pdf
[2] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/IEEE-802.11-b-g-n-Link-Controller-Module-with-Integrated-Bluetooth-5.0-DS70005327B.pdf

Fixes b2832b96fcf5 ("mmc: pwrseq: sd8787: add support for wilc1000")

Applied for fixes and by adding a stable tag, thanks!

Kind regards
Uffe

Quoted 92 lines

---
Cc: Ajay Singh <[email protected]>
Cc: Claudiu Beznea <[email protected]>
Cc: Ulf Hansson <[email protected]>
Cc: [email protected]

---
 drivers/mmc/core/pwrseq_sd8787.c | 34 ++++++++++++++++++++++++--------
 1 file changed, 26 insertions(+), 8 deletions(-)
drivers/mmc/core/pwrseq_sd8787.c +26 -9
index 2e120ad83020f..0c5f5e371e1f8 100644
@@ -28,7 +28,6 @@ struct mmc_pwrseq_sd8787 {
        struct mmc_pwrseq pwrseq;
        struct gpio_desc *reset_gpio;
        struct gpio_desc *pwrdn_gpio;
-       u32 reset_pwrdwn_delay_ms;
 };
 
 #define to_pwrseq_sd8787(p) container_of(p, struct mmc_pwrseq_sd8787, pwrseq)
@@ -39,7 +38,7 @@ static void mmc_pwrseq_sd8787_pre_power_on(struct mmc_host *host)
 
        gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
 
-       msleep(pwrseq->reset_pwrdwn_delay_ms);
+       msleep(300);
        gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
 }
 
@@ -51,17 +50,37 @@ static void mmc_pwrseq_sd8787_power_off(struct mmc_host *host)
        gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
 }
 
+static void mmc_pwrseq_wilc1000_pre_power_on(struct mmc_host *host)
+{
+       struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+       /* The pwrdn_gpio is really CHIP_EN, reset_gpio is RESETN */
+       gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 1);
+       msleep(5);
+       gpiod_set_value_cansleep(pwrseq->reset_gpio, 1);
+}
+
+static void mmc_pwrseq_wilc1000_power_off(struct mmc_host *host)
+{
+       struct mmc_pwrseq_sd8787 *pwrseq = to_pwrseq_sd8787(host->pwrseq);
+
+       gpiod_set_value_cansleep(pwrseq->reset_gpio, 0);
+       gpiod_set_value_cansleep(pwrseq->pwrdn_gpio, 0);
+}
+
 static const struct mmc_pwrseq_ops mmc_pwrseq_sd8787_ops = {
        .pre_power_on = mmc_pwrseq_sd8787_pre_power_on,
        .power_off = mmc_pwrseq_sd8787_power_off,
 };
 
-static const u32 sd8787_delay_ms = 300;
-static const u32 wilc1000_delay_ms = 5;
+static const struct mmc_pwrseq_ops mmc_pwrseq_wilc1000_ops = {
+       .pre_power_on = mmc_pwrseq_wilc1000_pre_power_on,
+       .power_off = mmc_pwrseq_wilc1000_power_off,
+};
 
 static const struct of_device_id mmc_pwrseq_sd8787_of_match[] = {
-       { .compatible = "mmc-pwrseq-sd8787", .data = &sd8787_delay_ms },
-       { .compatible = "mmc-pwrseq-wilc1000", .data = &wilc1000_delay_ms },
+       { .compatible = "mmc-pwrseq-sd8787", .data = &mmc_pwrseq_sd8787_ops },
+       { .compatible = "mmc-pwrseq-wilc1000", .data = &mmc_pwrseq_wilc1000_ops },
        {/* sentinel */},
 };
 MODULE_DEVICE_TABLE(of, mmc_pwrseq_sd8787_of_match);
@@ -77,7 +96,6 @@ static int mmc_pwrseq_sd8787_probe(struct platform_device *pdev)
                return -ENOMEM;
 
        match = of_match_node(mmc_pwrseq_sd8787_of_match, pdev->dev.of_node);
-       pwrseq->reset_pwrdwn_delay_ms = *(u32 *)match->data;
 
        pwrseq->pwrdn_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_LOW);
        if (IS_ERR(pwrseq->pwrdn_gpio))
@@ -88,7 +106,7 @@ static int mmc_pwrseq_sd8787_probe(struct platform_device *pdev)
                return PTR_ERR(pwrseq->reset_gpio);
 
        pwrseq->pwrseq.dev = dev;
-       pwrseq->pwrseq.ops = &mmc_pwrseq_sd8787_ops;
+       pwrseq->pwrseq.ops = match->data;
        pwrseq->pwrseq.owner = THIS_MODULE;
        platform_set_drvdata(pdev, pwrseq);
 
--

2.39.2