PSCI support for r8a7790 SoC (Lager/Stout boards)
Subsystems (2)
cover PSCI support for r8a7790 SoC (Lager/Stout boards)
From: Oleksandr Tyshchenko <[email protected]>
Hi, all.
The purpose of this patch series is to add PSCI support for Renesas boards based on R-Car Gen2 r8a7790 SoC. Actually, our target in Stout board, but as Lager board is also based on the same SoC, that patch series covers both.
The main goal of using PSCI is to have common interface to boot CPUs from Hypervisor/Linux. PSCI is a generic well-known way to bring-up CPU and proven to work. With this patch series applied all CPUs will be switched to a non-secure Hypervisor mode. For running Type 1 Hypervisor (e.g. Xen) it is mandatory requirement. From other side, there are recommendation to boot Linux in Hypervisor mode on ARM. This allows KVM or other Hypervisor (e.g. Jailhouse) to be useable on the platform. If there are no Hypervisor present, Linux will just initialize the Hypervisor mode correctly and drop to Supervisor mode.
Till now, we have been using a *custom solution* for running Xen Hypervisor on Lager/Stout boards, which requires a specific U-Boot version (which performs СPUs boot in a non-generic way) and different hacks into R-Car Gen2 platform code in Linux. We have a situation where different methods are used in order to boot CPUs from Xen/Linux. Which results in a forced switching between different U-Boot versions, when we need to switch between bare Linux and Xen, which is quite inconvenient. This should be totally transparent to the user.
----------
Current patch series is based on the following commit:425c0a43fbbec36571f6a03b530695b8b16a841d “Prepare v2019.01-rc3”
It was tested with bare Linux 5.0.0-rc3 and Xen 4.12.0-rc with Linux 5.0.0-rc3 as guest OS. Everything worked as expected.
In case of bare Linux, all CPU cores started in HYP mode and PSCI checker confirmed that hotplug tests had successfully passed.
Just one note. For each secondary CPU boot, Linux complains about
“Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable”.
Probably because the corresponding ARM errata (CONFIG_ARM_CORTEX_A15_CVE_2017_5715, etc) is not propagated to non-boot (secondary) CPUs.
You can also find patch series here (last 3 patches):
https://github.com/otyshchenko1/u-boot/commits/r8a7790_psci_upstream
----------
Please note:
1. Current patch series implies corresponding changes to Linux.
You can find them here (last 2 patches):
https://github.com/otyshchenko1/linux/commits/psci_upstream
I am about to push them as well.
2. As PSCI code expects a bigger “Maximum supported CPUs for PSCI” value (8) than default option (4), you will get a compilation error:arch/arm/mach-rmobile/psci.c:21:2: error: #error "invalid value for CONFIG_ARMV7_PSCI_NR_CPUS" #error "invalid value for CONFIG_ARMV7_PSCI_NR_CPUS"
To resolve it, just run make menuconfig, set this option to 8 (or change in .config directly) and recompile.
----------
Oleksandr Tyshchenko (3):
ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based
boards
ARM: rmobile: Add basic PSCI support for r8a7790 SoC
ARM: rmobile: Add possibility to debug main PSCI commands
arch/arm/mach-rmobile/Kconfig.32 | 6 + arch/arm/mach-rmobile/Makefile | 6 + arch/arm/mach-rmobile/debug.h | 91 +++++++++ arch/arm/mach-rmobile/pm-r8a7790.c | 408 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/pm-r8a7790.h | 72 +++++++ arch/arm/mach-rmobile/psci.c | 216 ++++++++++++++++++++ board/renesas/lager/lager.c | 51 +++++ board/renesas/stout/stout.c | 51 +++++ include/configs/lager.h | 5 + include/configs/stout.h | 5 + 10 files changed, 911 insertions(+) create mode 100644 arch/arm/mach-rmobile/debug.h create mode 100644 arch/arm/mach-rmobile/pm-r8a7790.c create mode 100644 arch/arm/mach-rmobile/pm-r8a7790.h create mode 100644 arch/arm/mach-rmobile/psci.c
Signature · 1 line
2.7.4
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty, since our target is to use PSCI for that.
Also take care of updating arch timer while we are in secure mode.
--- arch/arm/mach-rmobile/Kconfig.32 | 4 ++++ board/renesas/lager/lager.c | 51 ++++++++++++++++++++++++++++++++++++++++ board/renesas/stout/stout.c | 51 ++++++++++++++++++++++++++++++++++++++++ include/configs/lager.h | 3 +++ include/configs/stout.h | 3 +++ 5 files changed, 112 insertions(+)
arch/arm/mach-rmobile/Kconfig.32 +4 -0
@@ -76,6 +76,8 @@ config TARGET_LAGER select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT config TARGET_KZM9G bool "KZM9D board"
@@ -115,6 +117,8 @@ config TARGET_STOUT select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT endchoice
board/renesas/lager/lager.c +51 -0
63 lines not on this page · raw message
board/renesas/stout/stout.c +51 -0
63 lines not on this page · raw message
include/configs/lager.h +3 -0
@@ -48,4 +48,7 @@#define CONFIG_SH_SCIF_CLK_FREQ 65000000#endif +/* The PERIPHBASE in the CBAR register is wrong, so override it */ +#define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#endif /* __LAGER_H */
include/configs/stout.h +3 -0
@@ -56,4 +56,7 @@#define CONFIG_SH_SCIF_CLK_FREQ 52000000#endif +/* The PERIPHBASE in the CBAR register is wrong, so override it */ +#define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#endif /* __STOUT_H */
Signature · 1 line
2.7.4
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 23 lines · Oleksandr Tyshchenko
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty, since our target is to use PSCI for that.
Also take care of updating arch timer while we are in secure mode.
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/Kconfig.32 | 4 ++++ board/renesas/lager/lager.c | 51 ++++++++++++++++++++++++++++++++++++++++ board/renesas/stout/stout.c | 51 ++++++++++++++++++++++++++++++++++++++++ include/configs/lager.h | 3 +++ include/configs/stout.h | 3 +++ 5 files changed, 112 insertions(+)arch/arm/mach-rmobile/Kconfig.32 +0
-0
arch/arm/mach-rmobile/Kconfig.32 config TARGET_LAGER · line 80
Quoted 5 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0@@ -76,6 +76,8 @@ config TARGET_LAGER select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT
Shouldn't this be a H2 CPU property instead of a board property ? Does this apply to M2* too , since it has CA15 cores as well ?
Quoted 30 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0config TARGET_KZM9G bool "KZM9D board"@@ -115,6 +117,8 @@ config TARGET_STOUT select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT endchoiceboard/renesas/lager/lager.c +11
-0@@ -76,6 +76,53 @@ int board_early_init_f(void)return 0 ; } +#ifdef CONFIG_ARMV7_NONSEC +#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00 +#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode +* and we are going to enter kernel/hypervisor in a non-secure mode, update +* arch timer right now to avoid possible issues. Make sure arch timer is +* enabled and configured to use proper frequency. +*/
board/renesas/lager/lager.c int board_early_init_f(void) · line 99
Quoted 10 lines
board/renesas/lager/lager.c +10
-0+static void rcar_gen2_timer_init (void ) +{ +u32 freq =RMOBILE_XTAL_CLK /2 ; + +/* +* Update the arch timer if it is either not running, or is not at the +* right frequency. +*/ +if ((readl (TIMER_BASE +TIMER_CNTCR ) &1 ) ==0 || +readl (TIMER_BASE +TIMER_CNTFID0 ) != freq) {
What is this check about ?
board/renesas/lager/lager.c int board_early_init_f(void) · line 105
Quoted 6 lines
board/renesas/lager/lager.c +6
-0+/* Update registers with correct frequency */ +writel (freq,TIMER_BASE +TIMER_CNTFID0 ); + asmvolatile ("mcr p15, 0, %0, c14, c0, 0" : :"r" (freq)); + +/* Make sure arch timer is started by setting bit 0 of CNTCR */ +writel (1 ,TIMER_BASE +TIMER_CNTCR );
Shouldn't this be in the timer driver instead ?
board/renesas/lager/lager.c int board_early_init_f(void) · line 112
Quoted 7 lines
board/renesas/lager/lager.c +7
-0+ } +} + +/* +* In order not to break compilation if someone decides to build with PSCI +* support disabled, keep these dummy functions. +*/
That's currently the only use-case.
Quoted 17 lines
board/renesas/lager/lager.c +13
-0+void smp_set_core_boot_addr (unsigned long addr,int corenr) +{ +} + +void smp_kick_all_cpus (void ) +{ +} + +void smp_waitloop (unsigned int previous_address) +{ +} +#endif +#define ETHERNET_PHY_RESET 185/* GPIO 5 31 */ int board_init (void )
board/renesas/lager/lager.c int board_init(void) · line 139
Quoted 4 lines
board/renesas/lager/lager.c +1
-0@@ -89,6 +136,10 @@ int board_init(void)mdelay (10 );gpio_direction_output (ETHERNET_PHY_RESET ,1 ); +#ifdef CONFIG_ARMV7_NONSEC
Define empty function in case the macro is not set instead of ifdefing every place that calls the rcar_gen2_timer_init() function.
Quoted 17 lines
board/renesas/lager/lager.c +3
-0+rcar_gen2_timer_init (); +#endif +return 0 ; }board/renesas/stout/stout.c +3
-0@@ -77,6 +77,53 @@ int board_early_init_f(void)return 0 ; } +#ifdef CONFIG_ARMV7_NONSEC +#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00
board/renesas/stout/stout.c int board_early_init_f(void) · line 92
Quoted 10 lines
board/renesas/stout/stout.c +10
-0+#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode +* and we are going to enter kernel/hypervisor in a non-secure mode, update +* arch timer right now to avoid possible issues. Make sure arch timer is +* enabled and configured to use proper frequency. +*/ +static void rcar_gen2_timer_init (void ) +{
Why is this stuff in board code ? It should be in driver code / core code. And there should be only one copy of it.
Quoted 73 lines
board/renesas/stout/stout.c +38
-0+u32 freq =RMOBILE_XTAL_CLK /2 ; + +/* +* Update the arch timer if it is either not running, or is not at the +* right frequency. +*/ +if ((readl (TIMER_BASE +TIMER_CNTCR ) &1 ) ==0 || +readl (TIMER_BASE +TIMER_CNTFID0 ) != freq) { +/* Update registers with correct frequency */ +writel (freq,TIMER_BASE +TIMER_CNTFID0 ); + asmvolatile ("mcr p15, 0, %0, c14, c0, 0" : :"r" (freq)); + +/* Make sure arch timer is started by setting bit 0 of CNTCR */ +writel (1 ,TIMER_BASE +TIMER_CNTCR ); + } +} + +/* +* In order not to break compilation if someone decides to build with PSCI +* support disabled, keep these dummy functions. +*/ +void smp_set_core_boot_addr (unsigned long addr,int corenr) +{ +} + +void smp_kick_all_cpus (void ) +{ +} + +void smp_waitloop (unsigned int previous_address) +{ +} +#endif +#define ETHERNET_PHY_RESET 123/* GPIO 3 31 */ int board_init (void )@@ -92,6 +139,10 @@ int board_init(void)mdelay (20 );gpio_direction_output (ETHERNET_PHY_RESET ,1 ); +#ifdef CONFIG_ARMV7_NONSEC +rcar_gen2_timer_init (); +#endif +return 0 ; }include/configs/lager.h +3
-0@@ -48,4 +48,7 @@#define CONFIG_SH_SCIF_CLK_FREQ 65000000#endif +/* The PERIPHBASE in the CBAR register is wrong, so override it */ +#define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#endif /* __LAGER_H */ include/configs/stout.h +3
-0@@ -56,4 +56,7 @@#define CONFIG_SH_SCIF_CLK_FREQ 52000000#endif +/* The PERIPHBASE in the CBAR register is wrong, so override it */ +#define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#endif /* __STOUT_H */
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
On 05.02.19 20:48, Marek Vasut wrote:
Hi Marek
Quoted 19 lines · Oleksandr Tyshchenko
Quoted 18 lines
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty, since our target is to use PSCI for that.
Also take care of updating arch timer while we are in secure mode.
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/Kconfig.32 | 4 ++++ board/renesas/lager/lager.c | 51 ++++++++++++++++++++++++++++++++++++++++ board/renesas/stout/stout.c | 51 ++++++++++++++++++++++++++++++++++++++++ include/configs/lager.h | 3 +++ include/configs/stout.h | 3 +++ 5 files changed, 112 insertions(+)
Quoted 11 lines
arch/arm/mach-rmobile/Kconfig.32 config TARGET_LAGER · line 80
Quoted 10 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0@@ -76,6 +76,8 @@ config TARGET_LAGER select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRTShouldn't this be a H2 CPU property instead of a board property ?
Probably yes, sounds reasonable. I will move these options under "config R8A7790".
Quoted 1 line
Does this apply to M2* too , since it has CA15 cores as well ?
I think, yes. But, without PSCI support being implemented for M2*, I think it is not worth to select these options for it as well.
Quoted 34 lines
Quoted 34 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0config TARGET_KZM9G bool "KZM9D board"@@ -115,6 +117,8 @@ config TARGET_STOUT select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT endchoiceboard/renesas/lager/lager.c +14
-0@@ -76,6 +76,53 @@ int board_early_init_f(void)return 0 ; } +#ifdef CONFIG_ARMV7_NONSEC +#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00 +#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode +* and we are going to enter kernel/hypervisor in a non-secure mode, update +* arch timer right now to avoid possible issues. Make sure arch timer is +* enabled and configured to use proper frequency. +*/ +static void rcar_gen2_timer_init (void ) +{ +u32 freq =RMOBILE_XTAL_CLK /2 ;
Quoted 8 lines
board/renesas/lager/lager.c int board_early_init_f(void) · line 99
Quoted 7 lines
board/renesas/lager/lager.c +7
-0+ +/* +* Update the arch timer if it is either not running, or is not at the +* right frequency. +*/ +if ((readl (TIMER_BASE +TIMER_CNTCR ) &1 ) ==0 || +readl (TIMER_BASE +TIMER_CNTFID0 ) != freq) {What is this check about ?
Actually, this code for updating arch timer was borrowed from Linux almost as is.
Code in Linux uses this check in order to update timer only if required (either timer disabled or uses wrong freq).
This check avoids abort in Linux if loader has already updated timer and switched to non-secure mode.
But here in U-Boot, while we are still in secure mode, we can safely remove this check and always update the timer. Shall I remove this check?
Quoted 8 lines
board/renesas/lager/lager.c int board_early_init_f(void) · line 105
Quoted 7 lines
board/renesas/lager/lager.c +6
-0+/* Update registers with correct frequency */ +writel (freq,TIMER_BASE +TIMER_CNTFID0 ); + asmvolatile ("mcr p15, 0, %0, c14, c0, 0" : :"r" (freq)); + +/* Make sure arch timer is started by setting bit 0 of CNTCR */ +writel (1 ,TIMER_BASE +TIMER_CNTCR );Shouldn't this be in the timer driver instead ?
Which timer driver? Probably, I missed something, but I didn't find any arch timer driver being used for Gen2.
I see that TMU timer (arch/sh/lib/time.c) is used as a system timer, but it is yet another IP.
Would it be correct, if I move arch timer updating code to arch/arm/mach-rmobile directory?
Actually, at the same location the corresponding code lives in Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/setup-rcar-gen2.c#L61
Quoted 9 lines
board/renesas/lager/lager.c int board_early_init_f(void) · line 112
Quoted 8 lines
board/renesas/lager/lager.c +7
-0+ } +} + +/* +* In order not to break compilation if someone decides to build with PSCI +* support disabled, keep these dummy functions. +*/ That's currently the only use-case.
Shall I drop this comment and dummy functions below?
Quoted 16 lines
Quoted 16 lines
board/renesas/lager/lager.c +13
-0+void smp_set_core_boot_addr (unsigned long addr,int corenr) +{ +} + +void smp_kick_all_cpus (void ) +{ +} + +void smp_waitloop (unsigned int previous_address) +{ +} +#endif +#define ETHERNET_PHY_RESET 185/* GPIO 5 31 */
Quoted 8 lines
board/renesas/lager/lager.c int board_init(void) · line 139
Quoted 6 lines
board/renesas/lager/lager.c +1
-0int board_init (void )@@ -89,6 +136,10 @@ int board_init(void)mdelay (10 );gpio_direction_output (ETHERNET_PHY_RESET ,1 ); +#ifdef CONFIG_ARMV7_NONSEC Define empty function in case the macro is not set instead of ifdefing every place that calls the
rcar_gen2_timer_init()function.
Agree, will do
Quoted 15 lines
Quoted 15 lines
board/renesas/lager/lager.c +3
-0+rcar_gen2_timer_init (); +#endif +return 0 ; }board/renesas/stout/stout.c +0
-0@@ -77,6 +77,53 @@ int board_early_init_f(void)return 0 ; }
Quoted 15 lines
board/renesas/stout/stout.c int board_early_init_f(void) · line 92
Quoted 13 lines
board/renesas/stout/stout.c +13
-0+#ifdef CONFIG_ARMV7_NONSEC +#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00 +#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode +* and we are going to enter kernel/hypervisor in a non-secure mode, update +* arch timer right now to avoid possible issues. Make sure arch timer is +* enabled and configured to use proper frequency. +*/ +static void rcar_gen2_timer_init (void ) +{Why is this stuff in board code ? It should be in driver code / core code. And there should be only one copy of it.
Completely agree about the only one copy. When we move this code out of Stout/Lager board files, we will have only one of it.
Quoted 75 lines
Quoted 74 lines
board/renesas/stout/stout.c +38
-0+u32 freq =RMOBILE_XTAL_CLK /2 ; + +/* +* Update the arch timer if it is either not running, or is not at the +* right frequency. +*/ +if ((readl (TIMER_BASE +TIMER_CNTCR ) &1 ) ==0 || +readl (TIMER_BASE +TIMER_CNTFID0 ) != freq) { +/* Update registers with correct frequency */ +writel (freq,TIMER_BASE +TIMER_CNTFID0 ); + asmvolatile ("mcr p15, 0, %0, c14, c0, 0" : :"r" (freq)); + +/* Make sure arch timer is started by setting bit 0 of CNTCR */ +writel (1 ,TIMER_BASE +TIMER_CNTCR ); + } +} + +/* +* In order not to break compilation if someone decides to build with PSCI +* support disabled, keep these dummy functions. +*/ +void smp_set_core_boot_addr (unsigned long addr,int corenr) +{ +} + +void smp_kick_all_cpus (void ) +{ +} + +void smp_waitloop (unsigned int previous_address) +{ +} +#endif +#define ETHERNET_PHY_RESET 123/* GPIO 3 31 */ int board_init (void )@@ -92,6 +139,10 @@ int board_init(void)mdelay (20 );gpio_direction_output (ETHERNET_PHY_RESET ,1 ); +#ifdef CONFIG_ARMV7_NONSEC +rcar_gen2_timer_init (); +#endif +return 0 ; }include/configs/lager.h +3
-0@@ -48,4 +48,7 @@#define CONFIG_SH_SCIF_CLK_FREQ 65000000#endif +/* The PERIPHBASE in the CBAR register is wrong, so override it */ +#define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#endif /* __LAGER_H */ include/configs/stout.h +3
-0@@ -56,4 +56,7 @@#define CONFIG_SH_SCIF_CLK_FREQ 52000000#endif +/* The PERIPHBASE in the CBAR register is wrong, so override it */ +#define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#endif /* __STOUT_H */
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 4 lines · Oleksandr
On 05.02.19 20:48, Marek Vasut wrote:
Hi Marek
Hi,
Quoted 34 lines
Quoted 21 lines · Oleksandr Tyshchenko
Quoted 20 lines
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty, since our target is to use PSCI for that.
Also take care of updating arch timer while we are in secure mode.
Signed-off-by Oleksandr Tyshchenko <[email protected]>---
arch/arm/mach-rmobile/Kconfig.32| 4 ++++
board/renesas/lager/lager.c | 51
++++++++++++++++++++++++++++++++++++++++
board/renesas/stout/stout.c | 51
++++++++++++++++++++++++++++++++++++++++
include/configs/lager.h | 3 +++
include/configs/stout.h | 3 +++5 files changed, 112 insertions(+)Quoted 12 lines
Quoted 11 lines
arch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -76,6 +76,8 @@ config TARGET_LAGERselect
SUPPORT_SPL
selectUSE_TINY_PRINTF
implyCMD_DM
+ selectCPU_V7_HAS_NONSEC
+ selectCPU_V7_HAS_VIRTShouldn't this be a H2 CPU property instead of a board property ?
Quoted 7 lines
Probably yes, sounds reasonable. I will move these options under "config R8A7790".
Quoted 1 line
Does this apply to M2* too , since it has CA15 cores as well ?
I think, yes. But, without PSCI support being implemented for M2*, I think it is not worth to select these options for it as well.
It's basically the same SoC with two CPU cores less, how would that PSCI be any different on M2 ?
Quoted 49 lines
Quoted 34 lines
Quoted 34 lines
config
TARGET_KZM9G
bool "KZM9D board"arch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -115,6 +117,8 @@ config TARGET_STOUTselect
SUPPORT_SPL
selectUSE_TINY_PRINTF
implyCMD_DM
+ selectCPU_V7_HAS_NONSEC
+ selectCPU_V7_HAS_VIRT
endchoice
diff --gita/board/renesas/lager/lager.cb/board/renesas/lager/lager.cindex 062e88c..9b96cc4 100644board/renesas/lager/lager.c +0
-0@@ -76,6 +76,53 @@ int board_early_init_f(void) return 0; }+#ifdef
CONFIG_ARMV7_NONSECboard/renesas/lager/lager.c +6
-0+#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00 +#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode
+ * and we are going to enter kernel/hypervisor in a non-secure mode, update
+ * arch timer right now to avoid possible issues. Make sure arch timer is
+ * enabled and configured to use proper frequency.
+ */board/renesas/lager/lager.c +4
-0+static void rcar_gen2_timer_init (void ) +{ + u32 freq = RMOBILE_XTAL_CLK / 2; +Quoted 8 lines
Quoted 7 lines
+ /*
+ * Update the arch timer if it is either not running, or is not at the
+ * right frequency.
+ */
+ if ((readl(TIMER_BASE + TIMER_CNTCR)& 1) == 0 ||
+readl(TIMER_BASE + TIMER_CNTFID0)!= freq) {What is this check about ?
Actually, this code for updating arch timer was borrowed from Linux almost as is.
Code in Linux uses this check in order to update timer only if required (either timer disabled or uses wrong freq).
Quoted 6 lines
This check avoids abort in Linux if loader has already updated timer and switched to non-secure mode.
But here in U-Boot, while we are still in secure mode, we can safely remove this check and always update the timer. Shall I remove this check?
Shouldn't the timer be correctly configured by U-Boot in the first place? And shouldn't this be done by timer driver rather than some ad-hoc init code?
Quoted 15 lines
Quoted 8 lines
Quoted 7 lines
+ /* Update registers with correct frequency */
+writel(freq, TIMER_BASE + TIMER_CNTFID0);
+ asmvolatile("mcr p15, 0, %0, c14, c0, 0" : : "r" (freq)); +
+ /* Make sure arch timer is started by setting bit 0 of CNTCR */ +writel(1, TIMER_BASE + TIMER_CNTCR);Shouldn't this be in the timer driver instead ?
Which timer driver? Probably, I missed something, but I didn't find any arch timer driver being used for Gen2.
I see that TMU timer (
arch/sh/lib/time.c) is used as a system timer, but it is yet another IP.
Quoted 6 lines
Would it be correct, if I move arch timer updating code to
arch/arm/mach-rmobiledirectory?Actually, at the same location the corresponding code lives in Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/setup-rcar-gen2.c#L61
Presumably if this is something else than TMU, it needs proper driver that goes into drivers/ .
Quoted 11 lines
Quoted 9 lines
Quoted 8 lines
+ }
board/renesas/lager/lager.c +4
-0+} + +/* +* In order not to break compilation if someone decides to build with PSCI
+ * support disabled, keep these dummy functions.
+ */That's currently the only use-case.
Shall I drop this comment and dummy functions below?
Since there is no PSCI support, yes.
[...]
I'd like to have a cover letter go with V2, which describes what you're trying to achieve here.
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 5 lines · Marek Vasut
Quoted 3 lines · Oleksandr
On 05.02.19 20:48, Marek Vasut wrote:
Hi Marek
Hi,
Hi,
Quoted 34 lines
Quoted 34 lines
Quoted 34 lines · Oleksandr Tyshchenko
Quoted 26 lines
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty, since our target is to use PSCI for that.
Also take care of updating arch timer while we are in secure mode.
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/Kconfig.32 | 4 ++++ board/renesas/lager/lager.c | 51 ++++++++++++++++++++++++++++++++++++++++ board/renesas/stout/stout.c | 51 ++++++++++++++++++++++++++++++++++++++++ include/configs/lager.h | 3 +++ include/configs/stout.h | 3 +++ 5 files changed, 112 insertions(+)arch/arm/mach-rmobile/Kconfig.32 +0
-0arch/arm/mach-rmobile/Kconfig.32 config TARGET_LAGER · line 80
Quoted 5 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0@@ -76,6 +76,8 @@ config TARGET_LAGER select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRTShouldn't this be a H2 CPU property instead of a board property ?
Quoted 8 lines
Quoted 6 lines
Probably yes, sounds reasonable. I will move these options under "config R8A7790".
Quoted 1 line
Does this apply to M2* too , since it has CA15 cores as well ?
I think, yes. But, without PSCI support being implemented for M2*, I think it is not worth to select these options for it as well.
It's basically the same SoC with two CPU cores less, how would that PSCI be any different on M2 ?
I need some time to investigate. I will come up with an answer later.
Quoted 53 lines
Quoted 53 lines
Quoted 35 lines
Quoted 35 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0config TARGET_KZM9G bool "KZM9D board"@@ -115,6 +117,8 @@ config TARGET_STOUT select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT endchoice diff --git a/board/renesas/lager/lager.c b/board/renesas/lager/lager.cindex 062e88c..9b96cc4 100644
board/renesas/lager/lager.c +6
-0@@ -76,6 +76,53 @@ int board_early_init_f(void) return 0; } +#ifdef CONFIG_ARMV7_NONSEC +#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00 +#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode
+ * and we are going to enter kernel/hypervisor in a non-secure mode, update
+ * arch timer right now to avoid possible issues. Make sure arch timer is
+ * enabled and configured to use proper frequency.
+ */board/renesas/lager/lager.c +4
-0+static void rcar_gen2_timer_init (void ) +{ + u32 freq = RMOBILE_XTAL_CLK / 2; +Quoted 8 lines
Quoted 7 lines
+ /*
+ * Update the arch timer if it is either not running, or is not at the
+ * right frequency.
+ */
+ if ((readl(TIMER_BASE + TIMER_CNTCR)& 1) == 0 ||
+readl(TIMER_BASE + TIMER_CNTFID0)!= freq) {What is this check about ?
Actually, this code for updating arch timer was borrowed from Linux almost as is.
Code in Linux uses this check in order to update timer only if required (either timer disabled or uses wrong freq).
This check avoids abort in Linux if loader has already updated timer and switched to non-secure mode.
Quoted 5 lines
Quoted 2 lines
But here in U-Boot, while we are still in secure mode, we can safely remove this check and always update the timer. Shall I remove this check?
Shouldn't the timer be correctly configured by U-Boot in the first place? And shouldn't this be done by timer driver rather than some ad-hoc init code?
Yes, this timer should be correctly configured by U-Boot. And yes, the timer
configuration code should be in a proper place.
Quoted 14 lines
Quoted 14 lines
Quoted 8 lines
Quoted 7 lines
+ /* Update registers with correct frequency */
+writel(freq, TIMER_BASE + TIMER_CNTFID0);
+ asmvolatile("mcr p15, 0, %0, c14, c0, 0" : : "r" (freq)); +
+ /* Make sure arch timer is started by setting bit 0 of CNTCR */ +writel(1, TIMER_BASE + TIMER_CNTCR);Shouldn't this be in the timer driver instead ?
Which timer driver? Probably, I missed something, but I didn't find any arch timer driver being used for Gen2.
I see that TMU timer (
arch/sh/lib/time.c) is used as a system timer, but it is yet another IP.
Quoted 8 lines
Quoted 6 lines
Would it be correct, if I move arch timer updating code to
arch/arm/mach-rmobiledirectory?Actually, at the same location the corresponding code lives in Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/setup-rcar-gen2.c#L61
Presumably if this is something else than TMU, it needs proper driver that goes into
drivers/.
Did I get your point correctly that new driver (specially for Gen2 arch timer) should be introduced in U-Boot and
the only one thing it is intended to do is to configure that timer for the future use by Linux/Hypervisor?
If yes, the only question I have is how that new driver is going to be populated? There is no corresponding node for arch timer in the device tree.
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/boot/dts/r8a7790.dtsi
So, do I need specially for this case add arch timer node with reg and compatible properties?
Sorry if I ask obvious questions, not familiar enough with U-Boot.
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
+ }
board/renesas/lager/lager.c +4
-0+} + +/* +* In order not to break compilation if someone decides to build with PSCI
+ * support disabled, keep these dummy functions.
+ */That's currently the only use-case.
Quoted 2 lines
Quoted 1 line
Shall I drop this comment and dummy functions below?
Since there is no PSCI support, yes.
Understand.
Quoted 5 lines
[...]
I'd like to have a cover letter go with V2, which describes what you're trying to achieve here.
Yes, sure. Cover letter is present for the current V1 as well.
I thought that I had CC-ed all.
This is a link to it:
Quoted 1 line
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 49 lines · Oleksandr
Quoted 5 lines · Marek Vasut
Quoted 3 lines · Oleksandr
On 05.02.19 20:48, Marek Vasut wrote:
Hi Marek
Hi,
Hi,
Quoted 39 lines
Quoted 39 lines
Quoted 23 lines · Oleksandr Tyshchenko
Quoted 21 lines
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty,
since our target is to use PSCI for that.Also take care of updating arch timer while we are in secure mode.
Signed-off-by Oleksandr Tyshchenko <[email protected]>---
arch/arm/mach-rmobile/Kconfig.32| 4 ++++
board/renesas/lager/lager.c | 51
++++++++++++++++++++++++++++++++++++++++
board/renesas/stout/stout.c | 51
++++++++++++++++++++++++++++++++++++++++
include/configs/lager.h | 3 +++
include/configs/stout.h | 3 +++5 files changed, 112 insertions(+)Quoted 12 lines
Quoted 11 lines
arch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -76,6 +76,8 @@ config TARGET_LAGERselect
SUPPORT_SPL
selectUSE_TINY_PRINTF
implyCMD_DM
+ selectCPU_V7_HAS_NONSEC
+ selectCPU_V7_HAS_VIRTShouldn't this be a H2 CPU property instead of a board property ?
Probably yes, sounds reasonable. I will move these options under "config
R8A7790".
Quoted 6 lines
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
Does this apply to M2* too , since it has CA15 cores as well ?
I think, yes. But, without PSCI support being implemented for M2*, I think it is not worth to select these options for it as well.
It's basically the same SoC with two CPU cores less, how would that PSCI be any different on M2 ?
I need some time to investigate. I will come up with an answer later.
From the first look:
1. It should be different total number of CPUs:
For R8A7790 we have the following:
#define R8A7790_PSCI_NR_CPUS 8
But for R8A7791 it seems we need to use:
#define R8A7791_PSCI_NR_CPUS 2
2. It should be new pm-r8a7791.c file which will don't have any CA7 related stuff (CPU cores, SCU, etc).
Or it should be the single pm-r8a779x.c which must distinguish what SoC is being used and do proper things.
Quoted 142 lines
Quoted 55 lines
Quoted 55 lines
Quoted 36 lines
Quoted 36 lines
config
TARGET_KZM9G
bool "KZM9D board"arch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -115,6 +117,8 @@ config TARGET_STOUTselect
SUPPORT_SPL
selectUSE_TINY_PRINTF
implyCMD_DM
+ selectCPU_V7_HAS_NONSEC
+ selectCPU_V7_HAS_VIRT
endchoice
diff --gita/board/renesas/lager/lager.cb/board/renesas/lager/lager.c
index 062e88c..9b96cc4 100644board/renesas/lager/lager.c +0
-0@@ -76,6 +76,53 @@ int board_early_init_f(void) return 0; }+#ifdef
CONFIG_ARMV7_NONSECboard/renesas/lager/lager.c +6
-0+#define TIMER_BASE 0xE6080000 +#define TIMER_CNTCR 0x00 +#define TIMER_CNTFID0 0x20 + +/* +* Taking into the account that arch timer is only configurable in secure mode
+ * and we are going to enter kernel/hypervisor in a non-secure mode, update
+ * arch timer right now to avoid possible issues. Make sure arch timer is
+ * enabled and configured to use proper frequency.
+ */board/renesas/lager/lager.c +4
-0+static void rcar_gen2_timer_init (void ) +{ + u32 freq = RMOBILE_XTAL_CLK / 2; +Quoted 8 lines
Quoted 7 lines
+ /*
+ * Update the arch timer if it is either not running, or is not at the
+ * right frequency.
+ */
+ if ((readl(TIMER_BASE + TIMER_CNTCR)& 1) == 0 ||
+readl(TIMER_BASE + TIMER_CNTFID0)!= freq) {What is this check about ?
Actually, this code for updating arch timer was borrowed from Linux almost as is.
Code in Linux uses this check in order to update timer only if required (either timer disabled or uses wrong freq).
This check avoids abort in Linux if loader has already updated timer and
switched to non-secure mode.Quoted 6 lines
Quoted 3 lines
But here in U-Boot, while we are still in secure mode, we can safely remove this check and always update the timer. Shall I remove this check?
Shouldn't the timer be correctly configured by U-Boot in the first place? And shouldn't this be done by timer driver rather than some ad-hoc init code?
Yes, this timer should be correctly configured by U-Boot. And yes, the timer
configuration code should be in a proper place.
Quoted 19 lines
Quoted 19 lines
Quoted 9 lines
Quoted 8 lines
+ /* Update registers with correct frequency */
+writel(freq, TIMER_BASE + TIMER_CNTFID0);
+ asmvolatile("mcr p15, 0, %0, c14, c0, 0" : : "r" (freq)); +
+ /* Make sure arch timer is started by setting bit 0 of CNTCR */
+writel(1, TIMER_BASE + TIMER_CNTCR);Shouldn't this be in the timer driver instead ?
Which timer driver? Probably, I missed something, but I didn't find any arch timer driver being used for Gen2.
I see that TMU timer (
arch/sh/lib/time.c) is used as a system timer, but
it is yet another IP.Would it be correct, if I move arch timer updating code to
arch/arm/mach-rmobiledirectory?Quoted 6 lines
Quoted 4 lines
Actually, at the same location the corresponding code lives in Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/setup-rcar-gen2.c#L61
Presumably if this is something else than TMU, it needs proper driver that goes into
drivers/.Did I get your point correctly that new driver (specially for Gen2 arch timer) should be introduced in U-Boot and
the only one thing it is intended to do is to configure that timer for the future use by Linux/Hypervisor?
If yes, the only question I have is how that new driver is going to be populated? There is no corresponding node for arch timer in the device tree.
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/boot/dts/r8a7790.dtsi
So, do I need specially for this case add arch timer node with reg and compatible properties?
Sorry if I ask obvious questions, not familiar enough with U-Boot.
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
+ }
board/renesas/lager/lager.c +4
-0+} + +/* +* In order not to break compilation if someone decides to build with PSCI
+ * support disabled, keep these dummy functions.
+ */That's currently the only use-case.
Quoted 2 lines
Quoted 1 line
Shall I drop this comment and dummy functions below?
Since there is no PSCI support, yes.
Understand.
Quoted 5 lines
[...]
I'd like to have a cover letter go with V2, which describes what you're trying to achieve here.
Yes, sure. Cover letter is present for the current V1 as well.
I thought that I had CC-ed all.
This is a link to it:
Quoted 1 line
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 62 lines · Oleksandr
Quoted 49 lines · Oleksandr
Quoted 5 lines · Marek Vasut
Quoted 3 lines · Oleksandr
On 05.02.19 20:48, Marek Vasut wrote:
Hi Marek
Hi,
Hi,
Quoted 39 lines
Quoted 39 lines
Quoted 23 lines · Oleksandr Tyshchenko
Quoted 21 lines
From: Oleksandr Tyshchenko <[email protected]>
Both Lager and Stout boards are based on r8a7790 SoC.
Leave platform specific functions for bringing seconadary CPUs up empty,
since our target is to use PSCI for that.Also take care of updating arch timer while we are in secure mode.
Signed-off-by Oleksandr Tyshchenko <[email protected]>---
arch/arm/mach-rmobile/Kconfig.32| 4 ++++
board/renesas/lager/lager.c | 51
++++++++++++++++++++++++++++++++++++++++
board/renesas/stout/stout.c | 51
++++++++++++++++++++++++++++++++++++++++
include/configs/lager.h | 3 +++
include/configs/stout.h | 3 +++5 files changed, 112 insertions(+)Quoted 12 lines
Quoted 11 lines
arch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -76,6 +76,8 @@ config TARGET_LAGERselect
SUPPORT_SPL
selectUSE_TINY_PRINTF
implyCMD_DM
+ selectCPU_V7_HAS_NONSEC
+ selectCPU_V7_HAS_VIRTShouldn't this be a H2 CPU property instead of a board property ?
Probably yes, sounds reasonable. I will move these options under "config
R8A7790".Quoted 6 lines
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
Does this apply to M2* too , since it has CA15 cores as well ?
I think, yes. But, without PSCI support being implemented for M2*, I think it is not worth to select these options for it as well.
It's basically the same SoC with two CPU cores less, how would that PSCI be any different on M2 ?
I need some time to investigate. I will come up with an answer later.
From the first look:
1. It should be different total number of CPUs:
Quoted 7 lines
For R8A7790 we have the following:
#define R8A7790_PSCI_NR_CPUS 8
But for R8A7791 it seems we need to use:
#define R8A7791_PSCI_NR_CPUS 2
This information should be in the DT for each SoC, so you should extract it from there.
Quoted 2 lines
2. It should be new
pm-r8a7791.cfile which will don't have any CA7 related stuff (CPU cores, SCU, etc).
I'd like to have a generic pm-gen2.c file , which parses the DT and figures the configuration out that way. We are trying to get rid of all the ad-hoc hardcoded configuration stuff in favor of DT.
Quoted 2 lines
Or it should be the single
pm-r8a779x.cwhich must distinguish what SoC is being used and do proper things.
Right
[...]
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
On 09.02.19 18:37, Marek Vasut wrote:
Hi
Quoted 38 lines
Quoted 26 lines
Quoted 16 lines
Quoted 16 lines
Quoted 16 lines
Quoted 4 lines
Quoted 4 lines
arch/arm/mach-rmobile/Kconfig.32 +0
-1--- a/arch/arm/mach-rmobile/Kconfig.32Quoted 8 lines
arch/arm/mach-rmobile/Kconfig.32 config TARGET_LAGER · line 80
Quoted 7 lines
+++ b/arch/arm/mach-rmobile/Kconfig.32
arch/arm/mach-rmobile/Kconfig.32 +2
-0@@ -76,6 +76,8 @@ config TARGET_LAGER select SUPPORT_SPL select USE_TINY_PRINTF imply CMD_DM + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRTShouldn't this be a H2 CPU property instead of a board property ?
Probably yes, sounds reasonable. I will move these options under "config
R8A7790".Quoted 6 lines
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
Does this apply to M2* too , since it has CA15 cores as well ?
I think, yes. But, without PSCI support being implemented for M2*, I think it is not worth to select these options for it as well.
It's basically the same SoC with two CPU cores less, how would that PSCI be any different on M2 ?
I need some time to investigate. I will come up with an answer later.
From the first look:
1. It should be different total number of CPUs:
Quoted 7 lines
For R8A7790 we have the following:
#define R8A7790_PSCI_NR_CPUS 8
But for R8A7791 it seems we need to use:
#define R8A7791_PSCI_NR_CPUS 2
This information should be in the DT for each SoC, so you should extract it from there.
Quoted 2 lines
2. It should be new
pm-r8a7791.cfile which will don't have any CA7 related stuff (CPU cores, SCU, etc).
Quoted 7 lines
I'd like to have a generic
pm-gen2.cfile , which parses the DT and figures the configuration out that way. We are trying to get rid of all the ad-hoc hardcoded configuration stuff in favor of DT.Quoted 2 lines
Or it should be the single
pm-r8a779x.cwhich must distinguish what SoC is being used and do proper things.Right
I agree to have a single generic pm-gen2.c file which covers all Gen2 SoCs.
But, unfortunately, I only have Stout boards (H2), and therefore can check only on them. This is why the current patch series adds support for H2 SoC only.
Theoretically, I could add support for M2 as well, but, I wouldn't have possibility to check.
I would focus on the r8a7790 for now, as the Stout board is our nearest target which we want to support in Xen and the PSCI feature is a mandatory option.
What do you think?
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Hi, Marek
Quoted 23 lines
Quoted 10 lines
Quoted 3 lines
2. It should be new
pm-r8a7791.cfile which will don't have any CA7 related stuff (CPU cores, SCU, etc).I'd like to have a generic
pm-gen2.cfile , which parses the DT and figures the configuration out that way. We are trying to get rid of all the ad-hoc hardcoded configuration stuff in favor of DT.Quoted 2 lines
Or it should be the single
pm-r8a779x.cwhich must distinguish what SoC is being used and do proper things.Right
I agree to have a single generic
pm-gen2.cfile which covers all Gen2 SoCs.But, unfortunately, I only have Stout boards (H2), and therefore can check only on them. This is why the current patch series adds support for H2 SoC only.
Theoretically, I could add support for M2 as well, but, I wouldn't have possibility to check.
Quoted 5 lines
I would focus on the r8a7790 for now, as the Stout board is our nearest target which we want to support in Xen and the PSCI feature is a mandatory option.
What do you think?
Could you, please, answer that question...
Quoted 3 lines
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 2 lines · Oleksandr
Hi, Marek
Hi,
Quoted 23 lines
Quoted 23 lines
Quoted 10 lines
Quoted 3 lines
2. It should be new
pm-r8a7791.cfile which will don't have any CA7 related stuff (CPU cores, SCU, etc).I'd like to have a generic
pm-gen2.cfile , which parses the DT and figures the configuration out that way. We are trying to get rid of all the ad-hoc hardcoded configuration stuff in favor of DT.Quoted 2 lines
Or it should be the single
pm-r8a779x.cwhich must distinguish what SoC is being used and do proper things.Right
I agree to have a single generic
pm-gen2.cfile which covers all Gen2 SoCs.But, unfortunately, I only have Stout boards (H2), and therefore can check only on them. This is why the current patch series adds support for H2 SoC only.
Theoretically, I could add support for M2 as well, but, I wouldn't have possibility to check.
Quoted 7 lines
Quoted 5 lines
I would focus on the r8a7790 for now, as the Stout board is our nearest target which we want to support in Xen and the PSCI feature is a mandatory option.
What do you think?
Could you, please, answer that question...
I am sorry, I am too busy right now. I will answer that once I can properly study the problem and give you a useful answer.
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
In reply to OleksandrOn 2/7/19 6:19 PM, Oleksandr wrote:
[...]
Quoted 34 lines
Quoted 17 lines
Quoted 17 lines
Quoted 8 lines
Quoted 7 lines
+ /* Update registers with correct frequency */
+writel(freq, TIMER_BASE + TIMER_CNTFID0);
+ asmvolatile("mcr p15, 0, %0, c14, c0, 0" : : "r" (freq)); +
+ /* Make sure arch timer is started by setting bit 0 of CNTCR */
+writel(1, TIMER_BASE + TIMER_CNTCR);Shouldn't this be in the timer driver instead ?
Which timer driver? Probably, I missed something, but I didn't find any arch timer driver being used for Gen2.
I see that TMU timer (
arch/sh/lib/time.c) is used as a system timer, but it is yet another IP.Would it be correct, if I move arch timer updating code to
arch/arm/mach-rmobiledirectory?Quoted 6 lines
Quoted 4 lines
Actually, at the same location the corresponding code lives in Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/setup-rcar-gen2.c#L61
Presumably if this is something else than TMU, it needs proper driver that goes into
drivers/.Did I get your point correctly that new driver (specially for Gen2 arch timer) should be introduced in U-Boot and
the only one thing it is intended to do is to configure that timer for the future use by Linux/Hypervisor?
If yes, the only question I have is how that new driver is going to be populated? There is no corresponding node for arch timer in the device tree.
Quoted 7 lines
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/boot/dts/r8a7790.dtsi
So, do I need specially for this case add arch timer node with reg and compatible properties?
Sorry if I ask obvious questions, not familiar enough with U-Boot.
You would need a DT entry and a bit of code to start the timer in case the PSCI is enabled, yes. This would then fit into the DM/DT paradigm.
Quoted 20 lines
Quoted 11 lines
Quoted 10 lines
Quoted 9 lines
Quoted 8 lines
+ }
board/renesas/lager/lager.c +4
-0+} + +/* +* In order not to break compilation if someone decides to build with PSCI
+ * support disabled, keep these dummy functions.
+ */That's currently the only use-case.
Shall I drop this comment and dummy functions below?
Since there is no PSCI support, yes.
Understand.
Quoted 5 lines
[...]
I'd like to have a cover letter go with V2, which describes what you're trying to achieve here.
Quoted 7 lines
Yes, sure. Cover letter is present for the current V1 as well.
I thought that I had CC-ed all.
This is a link to it:
Thanks
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
On 09.02.19 18:35, Marek Vasut wrote:
Hi
Quoted 40 lines · Oleksandr
[...]
Quoted 36 lines
Quoted 17 lines
Quoted 17 lines
Quoted 8 lines
Quoted 7 lines
+ /* Update registers with correct frequency */
+writel(freq, TIMER_BASE + TIMER_CNTFID0);
+ asmvolatile("mcr p15, 0, %0, c14, c0, 0" : : "r" (freq)); +
+ /* Make sure arch timer is started by setting bit 0 of CNTCR */
+writel(1, TIMER_BASE + TIMER_CNTCR);Shouldn't this be in the timer driver instead ?
Which timer driver? Probably, I missed something, but I didn't find any arch timer driver being used for Gen2.
I see that TMU timer (
arch/sh/lib/time.c) is used as a system timer, but it is yet another IP.Would it be correct, if I move arch timer updating code to
arch/arm/mach-rmobiledirectory?Quoted 6 lines
Quoted 4 lines
Actually, at the same location the corresponding code lives in Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/setup-rcar-gen2.c#L61
Presumably if this is something else than TMU, it needs proper driver that goes into
drivers/.Did I get your point correctly that new driver (specially for Gen2 arch timer) should be introduced in U-Boot and
the only one thing it is intended to do is to configure that timer for the future use by Linux/Hypervisor?
If yes, the only question I have is how that new driver is going to be populated? There is no corresponding node for arch timer in the device tree.
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/boot/dts/r8a7790.dtsi
Quoted 6 lines
Quoted 4 lines
So, do I need specially for this case add arch timer node with reg and compatible properties?
Sorry if I ask obvious questions, not familiar enough with U-Boot.
You would need a DT entry and a bit of code to start the timer in case the PSCI is enabled, yes. This would then fit into the DM/DT paradigm.
I understand your point, thank you.
Will create a simple driver for arch timer in V2.
Quoted 27 lines
Quoted 18 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
+ }
board/renesas/lager/lager.c +4
-0+} + +/* +* In order not to break compilation if someone decides to build with PSCI
+ * support disabled, keep these dummy functions.
+ */That's currently the only use-case.
Quoted 2 lines
Quoted 1 line
Shall I drop this comment and dummy functions below?
Since there is no PSCI support, yes.
Understand.
Quoted 4 lines
[...]
I'd like to have a cover letter go with V2, which describes what you're trying to achieve here.
Quoted 7 lines
Yes, sure. Cover letter is present for the current V1 as well.
I thought that I had CC-ed all.
This is a link to it:
Thanks
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
On 2/12/19 8:52 PM, Oleksandr wrote:
Hi,
[...]
I was thinking about this whole PSCI situation and how it's all implemented today. Basically what we do is generate a separate reduced shred of U-Boot, which will remain resident in memory and which could be called by some other software. That shred is a piece of U-Boot proper, but a lot of stuff is just torn away at runtime, so it's not the whole binary, just tattered remnants of it.
I really do not like this approach to the whole U-Boot PSCI in the first place, it seems really fragile and dangerous.
But look, U-Boot already has support for U-Boot SPL/TPL, which is small, can contain a full driver model, drivers and all the necessary support functionality. It is built from the same sources, at the same time, but it is not a shred of U-Boot proper but rather a separate entity.
So I wonder, can't we use this U-Boot SPL/TPL as the piece of code which would remain resident in memory and handle the PSCI calls instead ? I think U-Boot can load such a code or it could be somehow bundled with U-Boot proper (using a fitImage maybe ?). This way you won't have to re-implement all the drivers in arch/arm/, the DM/DT remains in place and the whole PSCI handler would be self-contained, so no need to fiddle with linker sections of U-Boot itself.
I am CCing other people who use this PSCI stuff in U-Boot, maybe they have some thoughts on this approach.
And I apologize again for taking this long to reply.
[...]
Signature · 2 lines
Best regards, Marek Vasut
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Quoted 39 lines · Marek Vasut
On 2/12/19 8:52 PM, Oleksandr wrote:
Hi,
[...]
I was thinking about this whole PSCI situation and how it's all implemented today. Basically what we do is generate a separate reduced
shred of U-Boot, which will remain resident in memory and which could be
called by some other software. That shred is a piece of U-Boot proper,
but a lot of stuff is just torn away at runtime, so it's not the whole
binary, just tattered remnants of it.I really do not like this approach to the whole U-Boot PSCI in the first
place, it seems really fragile and dangerous.But look, U-Boot already has support for U-Boot SPL/TPL, which is small,
can contain a full driver model, drivers and all the necessary support
functionality. It is built from the same sources, at the same time, but
it is not a shred of U-Boot proper but rather a separate entity.So I wonder, can't we use this U-Boot SPL/TPL as the piece of code which
would remain resident in memory and handle the PSCI calls instead ? I think U-Boot can load such a code or it could be somehow bundled with U-Boot proper (using a fitImage maybe ?). This way you won't have to re-implement all the drivers inarch/arm/, the DM/DT remains in place and the whole PSCI handler would be self-contained, so no need to fiddle
with linker sections of U-Boot itself.
Quoted 7 lines
I am CCing other people who use this PSCI stuff in U-Boot, maybe they have some thoughts on this approach.
And I apologize again for taking this long to reply.
[...]
Adding Chin Liang and Jeremy.
Regards
Ley Foon
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
In reply to Marek VasutQuoted 3 lines · Marek Vasut
On 2/12/19 8:52 PM, Oleksandr wrote:
Hi,
Hi
Quoted 26 lines
[...]
I was thinking about this whole PSCI situation and how it's all implemented today. Basically what we do is generate a separate reduced shred of U-Boot, which will remain resident in memory and which could be called by some other software. That shred is a piece of U-Boot proper, but a lot of stuff is just torn away at runtime, so it's not the whole binary, just tattered remnants of it.
I really do not like this approach to the whole U-Boot PSCI in the first place, it seems really fragile and dangerous.
But look, U-Boot already has support for U-Boot SPL/TPL, which is small, can contain a full driver model, drivers and all the necessary support functionality. It is built from the same sources, at the same time, but it is not a shred of U-Boot proper but rather a separate entity.
So I wonder, can't we use this U-Boot SPL/TPL as the piece of code which would remain resident in memory and handle the PSCI calls instead ? I think U-Boot can load such a code or it could be somehow bundled with U-Boot proper (using a fitImage maybe ?). This way you won't have to re-implement all the drivers in
arch/arm/, the DM/DT remains in place and the whole PSCI handler would be self-contained, so no need to fiddle with linker sections of U-Boot itself.
Quoted 2 lines
I am CCing other people who use this PSCI stuff in U-Boot, maybe they have some thoughts on this approach.
Thank you for your honest answer.
Let's see what the community will say.
Quoted 2 lines
And I apologize again for taking this long to reply.
No problem.
Quoted 3 lines
[...]
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 1/3 ARM: rmobile: Switch CPU to non-secure HYP mode for r8a7790 based boards
Hi,
Quoted 37 lines
From: Oleksandr <[email protected]>
Sent: jeudi 14 mars 2019 12:37Quoted 3 lines · Marek Vasut
On 2/12/19 8:52 PM, Oleksandr wrote:
Hi,
Hi
Quoted 26 lines
[...]
I was thinking about this whole PSCI situation and how it's all implemented today. Basically what we do is generate a separate reduced shred of U-Boot, which will remain resident in memory and which could be called by some other software. That shred is a piece of U-Boot proper, but a lot of stuff is just torn away at runtime, so it's not the whole binary, just tattered remnants of it.
I really do not like this approach to the whole U-Boot PSCI in the first place, it seems really fragile and dangerous.
But look, U-Boot already has support for U-Boot SPL/TPL, which is small, can contain a full driver model, drivers and all the necessary support functionality. It is built from the same sources, at the same time, but it is not a shred of U-Boot proper but rather a separate entity.
So I wonder, can't we use this U-Boot SPL/TPL as the piece of code which would remain resident in memory and handle the PSCI calls instead ? I think U-Boot can load such a code or it could be somehow bundled with U-Boot proper (using a fitImage maybe ?). This way you won't have to re-implement all the drivers in
arch/arm/, the DM/DT remains in place and the whole PSCI handler would be self-contained, so no need to fiddle with linker sections of U-Boot itself.
Quoted 6 lines
Quoted 2 lines
I am CCing other people who use this PSCI stuff in U-Boot, maybe they have some thoughts on this approach.
Thank you for your honest answer.
Let's see what the community will say.
I will answer for STM32MP1 platform.
On STM32MP157 chip, the PSCI support is expected minimal in U-Boot for basic boot defconfig.
ROM code => SPL => U-Boot (install PSCI monitor) => Kernel
=> only CPU_ON/OFF for hotplug needed by kernel but no power management.
For full PSCI support (standby modes), we are using TF-A secure monitor (trusted boot defconfig) with full power support or OP-TEE secure monitor
ROM code => TF-A (BL2 install secure monitor = BL32 : SP min) => U-Boot (non secure world) => Kernel
ROM code => TF-A (BL2) => secure OS = OP-TEE => U-Boot (non secure world) => Kernel
In these 2 cases U-Boot access secure resource with SPCI request (SMC call).
But it in the future of the basic boot, if we want add a full PSCI support in U-Boot for power management, we need at least access to some resources:
- I2C driver
- STPMIC1 driver
- DDR driver (to switch the DDR in self refresh mode)
- Clock /reset driver
I agree all this part are already managed by U-Boot drivers / u-class. But we need also a way to have access to board information / DT description.
It is also why I don't implement the function psci_system_off() in ./arch/arm/mach-stm32mp/psci.c => I don't want recode a I2C driver in PSCI code...
void __secure psci_system_off(u32 function_id)
{
/* System Off is not managed, waiting user power off
* TODO: handle I2C write in PMIC Main Control register bit 0 = SWOFF
*/
while (1)
wfi();
}So have a PSCI firmware with driver model based on the U-Boot code (as it is done for SPL/TPL) seems for me a good solution.
Question: what the right moment to install the secure monitor ?
+ SPL=> U-Boot then U-Boot can use PSCI installed firmware but no access of secure resource in U-Boot
+ U-Boot => Kernel then U-Boot is executed in secure world can't use the PSCI firmware (as today)
PS: the first solution is used for some board when the secure monitor of TF-A = BL32 is installed by U-Boot (see CONFIG_SPL_ATF)
ROM code => SPL : install BL32 compiled from TF-A code => U-Boot (non secure world) => Kernel
Quoted 8 lines
Quoted 3 lines
And I apologize again for taking this long to reply.
No problem.
Quoted 1 line
Quoted 6 lines
Quoted 2 lines
[...]
--
Regards,Oleksandr Tyshchenko
Regards
Patrick
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
In reply to Oleksandr TyshchenkoFrom: Oleksandr Tyshchenko <[email protected]>
Also enable PSCI support for Stout and Lager boards where actually the r8a7790 SoC is installed.
All secondary CPUs will be switched to a non-secure HYP mode after booting.
--- arch/arm/mach-rmobile/Kconfig.32 | 2 + arch/arm/mach-rmobile/Makefile | 6 + arch/arm/mach-rmobile/pm-r8a7790.c | 408 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/pm-r8a7790.h | 72 +++++++ arch/arm/mach-rmobile/psci.c | 193 ++++++++++++++++++ include/configs/lager.h | 2 + include/configs/stout.h | 2 + 7 files changed, 685 insertions(+) create mode 100644 arch/arm/mach-rmobile/pm-r8a7790.c create mode 100644 arch/arm/mach-rmobile/pm-r8a7790.h create mode 100644 arch/arm/mach-rmobile/psci.c
arch/arm/mach-rmobile/Kconfig.32 +2 -0
@@ -78,6 +78,7 @@ config TARGET_LAGER imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI config TARGET_KZM9G bool "KZM9D board"
@@ -119,6 +120,7 @@ config TARGET_STOUT imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI endchoice
arch/arm/mach-rmobile/Makefile +6 -0
@@ -13,3 +13,9 @@ obj-$(CONFIG_SH73A0) += lowlevel_init.o cpu_info-sh73a0.o pfc-sh73a0.o obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o obj-$(CONFIG_RCAR_GEN2) += lowlevel_init_ca15.o cpu_info-rcar.o obj-$(CONFIG_RCAR_GEN3) += lowlevel_init_gen3.o cpu_info-rcar.o memmap-gen3.o + +ifndef CONFIG_SPL_BUILD +ifdef CONFIG_R8A7790 +obj-$(CONFIG_ARMV7_PSCI) += psci.o pm-r8a7790.o +endif +endif
arch/arm/mach-rmobile/pm-r8a7790.c new file +408 -0
408 lines not on this page · raw message
arch/arm/mach-rmobile/pm-r8a7790.h new file +72 -0
72 lines not on this page · raw message
arch/arm/mach-rmobile/psci.c new file +193 -0
193 lines not on this page · raw message
include/configs/lager.h +2 -0
@@ -51,4 +51,6 @@/* The PERIPHBASE in the CBAR register is wrong, so override it */ #define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#define CONFIG_ARMV7_PSCI_1_0 +#endif /* __LAGER_H */
include/configs/stout.h +2 -0
@@ -59,4 +59,6 @@/* The PERIPHBASE in the CBAR register is wrong, so override it */ #define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#define CONFIG_ARMV7_PSCI_1_0 +#endif /* __STOUT_H */
Signature · 1 line
2.7.4
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
Quoted 72 lines · Oleksandr Tyshchenko
From: Oleksandr Tyshchenko <[email protected]>
Also enable PSCI support for Stout and Lager boards where actually the r8a7790 SoC is installed.
All secondary CPUs will be switched to a non-secure HYP mode after booting.
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/Kconfig.32 | 2 + arch/arm/mach-rmobile/Makefile | 6 + arch/arm/mach-rmobile/pm-r8a7790.c | 408 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/pm-r8a7790.h | 72 +++++++ arch/arm/mach-rmobile/psci.c | 193 ++++++++++++++++++ include/configs/lager.h | 2 + include/configs/stout.h | 2 + 7 files changed, 685 insertions(+) create mode 100644 arch/arm/mach-rmobile/pm-r8a7790.c create mode 100644 arch/arm/mach-rmobile/pm-r8a7790.h create mode 100644 arch/arm/mach-rmobile/psci.carch/arm/mach-rmobile/Kconfig.32 +2
-0@@ -78,6 +78,7 @@ config TARGET_LAGER imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI config TARGET_KZM9G bool "KZM9D board"@@ -119,6 +120,7 @@ config TARGET_STOUT imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI endchoicearch/arm/mach-rmobile/Makefile +6
-0@@ -13,3 +13,9 @@ obj-$(CONFIG_SH73A0) += lowlevel_init.o cpu_info-sh73a0.o pfc-sh73a0.o obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o obj-$(CONFIG_RCAR_GEN2) += lowlevel_init_ca15.o cpu_info-rcar.o obj-$(CONFIG_RCAR_GEN3) += lowlevel_init_gen3.o cpu_info-rcar.o memmap-gen3.o + +ifndef CONFIG_SPL_BUILD +ifdef CONFIG_R8A7790 +obj-$(CONFIG_ARMV7_PSCI) += psci.o pm-r8a7790.o +endif +endifarch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0@@ -0,0 +1,408 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* CPU power management support for Renesas r8a7790 SoC +* +* Contains functions to control ARM Cortex A15/A7 cores and +* related peripherals basically used for PSCI. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Mainly based on Renesas R-Car Gen2 platform code from Linux:
arch/arm/mach-rmobile/pm-r8a7790.c line 20
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+* arch/arm/mach-shmobile/... +*/ + +#include <common.h> +#include <asm/secure.h> +#include <asm/io.h> + +#include "pm-r8a7790.h" + +/*****************************************************************************
I'd expect checkpatch to complain about these long lines of asterisks.
arch/arm/mach-rmobile/pm-r8a7790.c line 24
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +4
-0+* APMU definitions +*****************************************************************************/ +#define CA15_APMU_BASE 0xe6152000 +#define CA7_APMU_BASE 0xe6151000
All these addresses should come from DT. And the driver should be DM capable and live in drivers/
[...]
arch/arm/mach-rmobile/pm-r8a7790.c line 154
Quoted 13 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +13
-0+/***************************************************************************** +* Functions which intended to be called from PSCI handlers. These functions +* marked as __secure and are placed in .secure section. +*****************************************************************************/ +void __secure r8a7790_apmu_power_on(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 apmu_base; + + apmu_base = cluster ==0 ?CA15_APMU_BASE :CA7_APMU_BASE ; + +/* Request power on */ +writel (BIT (r8a7790_core_id (cpu)), apmu_base +WUPCR_OFFS );
wait_for_bit of some sorts ?
arch/arm/mach-rmobile/pm-r8a7790.c line 158
Quoted 3 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+/* Wait for APMU to finish */ +while (readl (apmu_base +WUPCR_OFFS )) + ;
Can this spin forever ?
Quoted 60 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +60
-0+} + +void __secure r8a7790_apmu_power_off(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 apmu_base; + + apmu_base = cluster ==0 ?CA15_APMU_BASE :CA7_APMU_BASE ; + +/* Request Core Standby for next WFI */ +writel (CPUPWR_STANDBY , apmu_base +CPUNCR_OFFS (r8a7790_core_id (cpu))); +} + +void __secure r8a7790_assert_reset(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 mask, magic, rescnt; + + mask =BIT (3 -r8a7790_core_id (cpu)); + magic = cluster ==0 ?CA15RESCNT_CODE :CA7RESCNT_CODE ; + rescnt =RST_BASE + (cluster ==0 ?CA15RESCNT :CA7RESCNT ); +writel ((readl (rescnt) | mask) | magic, rescnt); +} + +void __secure r8a7790_deassert_reset(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 mask, magic, rescnt; + + mask =BIT (3 -r8a7790_core_id (cpu)); + magic = cluster ==0 ?CA15RESCNT_CODE :CA7RESCNT_CODE ; + rescnt =RST_BASE + (cluster ==0 ?CA15RESCNT :CA7RESCNT ); +writel ((readl (rescnt) & ~mask) | magic, rescnt); +} + +void __secure r8a7790_system_reset(void) +{ +u32 bar; + +/* +* Before configuring internal watchdog timer (RWDT) to reboot system +* we need to re-program BAR registers for the boot CPU to jump to +* bootrom code. Without taking care of, the boot CPU will jump to +* the reset vector previously installed in ICRAM1, since BAR registers +* keep their values after watchdog triggered reset. +*/ + bar = (BOOTROM >>8 ) &0xfffffc00 ; +writel (bar,RST_BASE +CA15BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA15BAR ); +writel (bar,RST_BASE +CA7BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA7BAR ); +dsb (); + +/* Now, configure watchdog timer to reboot the system */ + +/* Trigger reset when counter overflows */ +writel (WDTRSTCR_CODE |0x2 ,RST_BASE +WDTRSTCR ); +dsb (); + +/* Stop counter */
arch/arm/mach-rmobile/pm-r8a7790.c line 228
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+writel (RWTCSRA_CODE ,RWDT_BASE +RWTCSRA ); + +/* Initialize counter with the highest value */ +writel (RWTCNT_CODE |0xffff ,RWDT_BASE +RWTCNT ); + +while (readb (RWDT_BASE +RWTCSRA ) &RWTCSRA_WRFLG ) + ; + +/* Start counter */ +writel (RWTCSRA_CODE |RWTCSRA_TME ,RWDT_BASE +RWTCSRA );
This seems to reimplement the reset code that's in U-Boot already. Why ?
Quoted 81 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +81
-0+} + +/***************************************************************************** +* Functions which intended to be called from PSCI board initialization. +*****************************************************************************/ +static int sysc_power_up (int scu) +{ +u32 status, chan_offs, isr_bit; +int i, j, ret =0 ; + +if (scu ==CA15_SCU ) { + chan_offs =CA15_SCU_CHAN_OFFS ; + isr_bit =CA15_SCU_ISR_BIT ; + }else { + chan_offs =CA7_SCU_CHAN_OFFS ; + isr_bit =CA7_SCU_ISR_BIT ; + } + +writel (BIT (isr_bit),SYSC_BASE +SYSCISCR ); + +/* Submit power resume request until it was accepted */ +for (i =0 ; i <PWRER_RETRIES ; i++) { +/* Wait until SYSC is ready to accept a power resume request */ +for (j =0 ; j <SYSCSR_RETRIES ; j++) { +if (readl (SYSC_BASE +SYSCSR ) &BIT (1 )) +break ; + +udelay (SYSCSR_DELAY_US ); + } + +if (j ==SYSCSR_RETRIES ) +return -EAGAIN ; + +/* Submit power resume request */ +writel (BIT (0 ),SYSC_BASE + chan_offs +PWRONCR_OFFS ); + +/* Check if power resume request was accepted */ + status =readl (SYSC_BASE + chan_offs +PWRER_OFFS ); +if (!(status &BIT (0 ))) +break ; + +udelay (PWRER_DELAY_US ); + } + +if (i ==PWRER_RETRIES ) +return -EIO ; + +/* Wait until the power resume request has completed */ +for (i =0 ; i <SYSCISR_RETRIES ; i++) { +if (readl (SYSC_BASE +SYSCISR ) &BIT (isr_bit)) +break ; +udelay (SYSCISR_DELAY_US ); + } + +if (i ==SYSCISR_RETRIES ) + ret = -EIO ; + +writel (BIT (isr_bit),SYSC_BASE +SYSCISCR ); + +return ret; +} + +static bool sysc_power_is_off (int scu) +{ +u32 status, chan_offs; + + chan_offs = scu ==CA15_SCU ?CA15_SCU_CHAN_OFFS :CA7_SCU_CHAN_OFFS ; + +/* Check if SCU is in power shutoff state */ + status =readl (SYSC_BASE + chan_offs +PWRSR_OFFS ); +if (status &BIT (0 )) +return true; + +return false; +} + +static void apmu_setup_debug_mode (int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 apmu_base, reg; +
arch/arm/mach-rmobile/pm-r8a7790.c line 319
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+ apmu_base = cluster ==0 ?CA15_APMU_BASE :CA7_APMU_BASE ; + +/* +* Enable reset requests derived from power shutoff to the AP-system +* CPU cores in debug mode. Without taking care of, they may fail to +* resume from the power shutoff state. +*/ + reg =readl (apmu_base +DBGRCR_OFFS ); + reg |=DBGCPUREN |DBGCPUNREN (r8a7790_core_id (cpu)) |DBGCPUPREN ; +writel (reg, apmu_base +DBGRCR_OFFS );
setbits_le32()
Quoted 12 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +12
-0+} + +/* +* Reset vector for secondary CPUs. +* This will be mapped at address 0 by SBAR register. +* We need _long_ jump to the physical address. +*/ +asm(" .arm\n" +" .align 12\n" +" .globl shmobile_boot_vector\n" +"shmobile_boot_vector:\n" + " ldr r1, 1f\n"
arch/arm/mach-rmobile/pm-r8a7790.c line 341
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+" bx r1\n" +" .type shmobile_boot_vector, %function\n" +" .size shmobile_boot_vector, .-shmobile_boot_vector\n" +" .align 2\n" +" .globl shmobile_boot_fn\n" +"shmobile_boot_fn:\n" +"1: .space 4\n" +" .globl shmobile_boot_size\n" +"shmobile_boot_size:\n" + " .long .-shmobile_boot_vector\n");
Why can't this be implemented in C ?
arch/arm/mach-rmobile/pm-r8a7790.c line 345
Quoted 3 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+extern void shmobile_boot_vector (void ); +extern unsigned long shmobile_boot_fn; +extern unsigned long shmobile_boot_size;
Are the externs necessary ?
arch/arm/mach-rmobile/pm-r8a7790.c line 359
Quoted 13 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +13
-0+void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus) +{ +int cpu =get_current_cpu (); +int i, ret =0 ; +u32 bar; + + shmobile_boot_fn = addr; +dsb (); + +/* Install reset vector */ +memcpy_toio ((void __iomem *)ICRAM1 , shmobile_boot_vector, + shmobile_boot_size); +dmb ();
Does this take into consideration caches ?
Quoted 16 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +16
-0+/* Setup reset vectors */ + bar = (ICRAM1 >>8 ) &0xfffffc00 ; +writel (bar,RST_BASE +CA15BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA15BAR ); +writel (bar,RST_BASE +CA7BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA7BAR ); +dsb (); + +/* Perform setup for debug mode for all CPUs */ +for (i =0 ; i < nr_cpus; i++) +apmu_setup_debug_mode (i); + +/* +* Indicate the completion status of power shutoff/resume procedure +* for CA15/CA7 SCU. +*/
arch/arm/mach-rmobile/pm-r8a7790.c line 386
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+writel (BIT (CA15_SCU_ISR_BIT ) |BIT (CA7_SCU_ISR_BIT ), +SYSC_BASE +SYSCIER ); + +/* Power on CA15/CA7 SCU */ +if (sysc_power_is_off (CA15_SCU )) + ret +=sysc_power_up (CA15_SCU ); +if (sysc_power_is_off (CA7_SCU )) + ret +=sysc_power_up (CA7_SCU ); +if (ret) +printf ("warning: some of secondary CPUs may not boot\n" );
"some" is not very useful for debugging,.
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+/* Keep secondary CPUs in reset */ +for (i =0 ; i < nr_cpus; i++) { +/* Make sure that we don't reset boot CPU */ +if (i == cpu) +continue ; + +r8a7790_assert_reset (i); + } + +/*
arch/arm/mach-rmobile/pm-r8a7790.c line 407
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+* Enable snoop requests and DVM message requests for slave interfaces +* S4 (CA7) and S3 (CA15). +*/ +writel (readl (CCI_BASE +CCI_SLAVE3 +CCI_SNOOP ) |CCI_ENABLE_REQ , +CCI_BASE +CCI_SLAVE3 +CCI_SNOOP ); +writel (readl (CCI_BASE +CCI_SLAVE4 +CCI_SNOOP ) |CCI_ENABLE_REQ , +CCI_BASE +CCI_SLAVE4 +CCI_SNOOP ); +/* Wait for pending bit low */ +while (readl (CCI_BASE +CCI_STATUS )) + ;
can this spin forever ?
Quoted 283 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +1
-0+}arch/arm/mach-rmobile/pm-r8a7790.h new file +72
-0@@ -0,0 +1,72 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (C) 2018 EPAM Systems Inc. +*/ + +#ifndef __PM_R8A7790_H__ +#define __PM_R8A7790_H__ + +#include <linux/types.h> + +void r8a7790_apmu_power_on (int cpu); +void r8a7790_apmu_power_off (int cpu); +void r8a7790_assert_reset (int cpu); +void r8a7790_deassert_reset (int cpu); + +void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus); +void r8a7790_system_reset (void ); + +#define R8A7790_NR_CLUSTERS 2 +#define R8A7790_NR_CPUS_PER_CLUSTER 4 + +/* Convert linear CPU index to core/cluster ID */ +#define r8a7790_cluster_id (cpu) ((cpu) / R8A7790_NR_CPUS_PER_CLUSTER) +#define r8a7790_core_id (cpu) ((cpu) % R8A7790_NR_CPUS_PER_CLUSTER) + +#define MPIDR_AFFLVL_MASK GENMASK(7, 0) +#define MPIDR_AFF0_SHIFT 0 +#define MPIDR_AFF1_SHIFT 8 + +/* All functions are inline so that they can be called from .secure section. */ + +/* +* Convert CPU ID in MPIDR format to linear CPU index. +* +* Below the possible CPU IDs and corresponding CPU indexes: +* CPU ID CPU index +* 0x80000000 - 0x00000000 +* 0x80000001 - 0x00000001 +* 0x80000002 - 0x00000002 +* 0x80000003 - 0x00000003 +* 0x80000100 - 0x00000004 +* 0x80000101 - 0x00000005 +* 0x80000102 - 0x00000006 +* 0x80000103 - 0x00000007 +*/ +static inline int mpidr_to_cpu_index (u32 mpidr) +{ +u32 cluster_id, cpu_id; + + cluster_id = (mpidr >>MPIDR_AFF1_SHIFT ) &MPIDR_AFFLVL_MASK ; + cpu_id = (mpidr >>MPIDR_AFF0_SHIFT ) &MPIDR_AFFLVL_MASK ; + +if (cluster_id >=R8A7790_NR_CLUSTERS ) +return -1 ; + +if (cpu_id >=R8A7790_NR_CPUS_PER_CLUSTER ) +return -1 ; + +return (cpu_id + (cluster_id *R8A7790_NR_CPUS_PER_CLUSTER )); +} + +/* Return an index of the CPU which performs this call */ +static inline int get_current_cpu (void ) +{ +u32 mpidr; + + asmvolatile ("mrc p15, 0, %0, c0, c0, 5" :"=r" (mpidr)); + +return mpidr_to_cpu_index (mpidr); +} + +#endif /* __PM_R8A7790_H__ */ arch/arm/mach-rmobile/psci.c new file +193
-0@@ -0,0 +1,193 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* This file implements basic PSCI support for Renesas r8a7790 SoC +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Based on arch/arm/mach-uniphier/arm32/psci.c +*/ + +#include <common.h> +#include <linux/psci.h> +#include <asm/io.h> +#include <asm/psci.h> +#include <asm/secure.h> + +#include "pm-r8a7790.h" + +#define R8A7790_PSCI_NR_CPUS 8 +#if R8A7790_PSCI_NR_CPUS >CONFIG_ARMV7_PSCI_NR_CPUS +#error "invalid value for CONFIG_ARMV7_PSCI_NR_CPUS" +#endif + +#define GICC_CTLR_OFFSET 0x2000 + +/* +* The boot CPU is powered on by default, but it's index is not a const +* value. An index the boot CPU has, depends on whether it is CA15 (index 0) +* or CA7 (index 4). +* So, we update state for the boot CPU during PSCI board initialization. +*/ +u8 psci_state[R8A7790_PSCI_NR_CPUS] __secure_data = { +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF }; + +void __secure psci_set_state(int cpu, u8 state) +{ + psci_state[cpu] = state; +dsb (); +isb (); +} + +u32 __secure psci_get_cpu_id(void) +{ +return get_current_cpu (); +} + +void __secure psci_arch_cpu_entry(void) +{ +int cpu =get_current_cpu (); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON ); +} + +int __secure psci_features(u32 function_id, u32 psci_fid) +{ +switch (psci_fid) { +case ARM_PSCI_0_2_FN_PSCI_VERSION : +case ARM_PSCI_0_2_FN_CPU_OFF : +case ARM_PSCI_0_2_FN_CPU_ON : +case ARM_PSCI_0_2_FN_AFFINITY_INFO : +case ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE : +case ARM_PSCI_0_2_FN_SYSTEM_OFF : +case ARM_PSCI_0_2_FN_SYSTEM_RESET : +return 0x0 ; + } + +return ARM_PSCI_RET_NI ; +} + +u32 __secure psci_version(u32 function_id) +{ +return ARM_PSCI_VER_1_0 ; +} + +int __secure psci_affinity_info(u32 function_id, u32 target_affinity, +u32 lowest_affinity_level) +{ +int cpu; + +if (lowest_affinity_level >0 ) +return ARM_PSCI_RET_INVAL ; + + cpu =mpidr_to_cpu_index (target_affinity); +if (cpu ==-1 ) +return ARM_PSCI_RET_INVAL ; + +/* TODO flush cache */ +return psci_state[cpu]; +} + +int __secure psci_migrate_info_type(u32 function_id) +{ +/* Trusted OS is either not present or does not require migration */ +return 2 ; +} + +int __secure psci_cpu_on(u32 function_id, u32 target_cpu, u32 entry_point, +u32 context_id) +{ +int cpu; + + cpu =mpidr_to_cpu_index (target_cpu); +if (cpu ==-1 ) +return ARM_PSCI_RET_INVAL ; + +if (psci_state[cpu] ==PSCI_AFFINITY_LEVEL_ON ) +return ARM_PSCI_RET_ALREADY_ON ; + +if (psci_state[cpu] ==PSCI_AFFINITY_LEVEL_ON_PENDING ) +return ARM_PSCI_RET_ON_PENDING ; + +psci_save (cpu, entry_point, context_id); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON_PENDING ); + +r8a7790_assert_reset (cpu); +r8a7790_apmu_power_on (cpu); +r8a7790_deassert_reset (cpu); + +return ARM_PSCI_RET_SUCCESS ; +} + +int __secure psci_cpu_off(void) +{ +int cpu =get_current_cpu (); + +/* +* Place the CPU interface in a state where it can never make a CPU +* exit WFI as result of an asserted interrupt. +*/ +writel (0 ,CONFIG_ARM_GIC_BASE_ADDRESS +GICC_CTLR_OFFSET ); +dsb (); + +/* Select next sleep mode using the APMU */ +r8a7790_apmu_power_off (cpu); + +/* Do ARM specific CPU shutdown */ +psci_cpu_off_common (); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_OFF ); + +/* Drain the WB before WFI */ +dsb (); + +while (1 ) +wfi (); +} + +void __secure psci_system_reset(u32 function_id) +{ +r8a7790_system_reset (); + +/* Drain the WB before WFI */ +dsb (); + +/* The system is about to be rebooted, so just waiting for this */ +while (1 ) +wfi (); +} + +void __secure psci_system_off(u32 function_id) +{ +/* Drain the WB before WFI */ +dsb (); + +/* +* System Off is not implemented yet, so waiting for powering off +* manually +*/ +while (1 ) +wfi (); +} + +void psci_board_init (void ) +{ +int cpu =get_current_cpu (); + +/* Update state for the boot CPU */ +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON ); + +/* +* Perform needed actions for the secondary CPUs to be ready +* for powering on +*/ +r8a7790_prepare_cpus ((unsigned long )psci_cpu_entry, +R8A7790_PSCI_NR_CPUS ); +}include/configs/lager.h +0
-0
include/configs/lager.h line 54
Quoted 4 lines
include/configs/lager.h +1
-0@@ -51,4 +51,6 @@/* The PERIPHBASE in the CBAR register is wrong, so override it */ #define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000 +#define CONFIG_ARMV7_PSCI_1_0
Why is this in board code, shouldn't that be in platform code ?
[...]
Signature · 2 lines
Best regards, Marek Vasut
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
On 05.02.19 20:55, Marek Vasut wrote:
Hi Marek
Quoted 33 lines · Oleksandr Tyshchenko
Quoted 32 lines
From: Oleksandr Tyshchenko <[email protected]>
Also enable PSCI support for Stout and Lager boards where actually the r8a7790 SoC is installed.
All secondary CPUs will be switched to a non-secure HYP mode after booting.
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/Kconfig.32 | 2 + arch/arm/mach-rmobile/Makefile | 6 + arch/arm/mach-rmobile/pm-r8a7790.c | 408 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/pm-r8a7790.h | 72 +++++++ arch/arm/mach-rmobile/psci.c | 193 ++++++++++++++++++ include/configs/lager.h | 2 + include/configs/stout.h | 2 + 7 files changed, 685 insertions(+)create mode 100644
arch/arm/mach-rmobile/pm-r8a7790.ccreate mode 100644arch/arm/mach-rmobile/pm-r8a7790.hcreate mode 100644arch/arm/mach-rmobile/psci.carch/arm/mach-rmobile/Kconfig.32 +1
-0@@ -78,6 +78,7 @@ config TARGET_LAGER imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI
Quoted 7 lines
arch/arm/mach-rmobile/Kconfig.32 config TARGET_STOUT · line 123
Quoted 7 lines
arch/arm/mach-rmobile/Kconfig.32 +1
-0config TARGET_KZM9G bool "KZM9D board"@@ -119,6 +120,7 @@ config TARGET_STOUT imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCI
To myself: Move this option under "config R8A7790".
Quoted 36 lines
Quoted 36 lines
arch/arm/mach-rmobile/Kconfig.32 +0
-0endchoicearch/arm/mach-rmobile/Makefile +6
-0@@ -13,3 +13,9 @@ obj-$(CONFIG_SH73A0) += lowlevel_init.o cpu_info-sh73a0.o pfc-sh73a0.o obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o obj-$(CONFIG_RCAR_GEN2) += lowlevel_init_ca15.o cpu_info-rcar.o obj-$(CONFIG_RCAR_GEN3) += lowlevel_init_gen3.o cpu_info-rcar.o memmap-gen3.o + +ifndef CONFIG_SPL_BUILD +ifdef CONFIG_R8A7790 +obj-$(CONFIG_ARMV7_PSCI) += psci.o pm-r8a7790.o +endif +endifarch/arm/mach-rmobile/pm-r8a7790.c new file +13
-0@@ -0,0 +1,408 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* CPU power management support for Renesas r8a7790 SoC +* +* Contains functions to control ARM Cortex A15/A7 cores and +* related peripherals basically used for PSCI. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Mainly based on Renesas R-Car Gen2 platform code from Linux: +* arch/arm/mach-shmobile/... +*/ +
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 20
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+#include <common.h> +#include <asm/secure.h> +#include <asm/io.h> + +#include "pm-r8a7790.h" + +/***************************************************************************** I'd expect checkpatch to complain about these long lines of asterisks.
No, there was no complain about it. I have checked. Anyway, I can remove them if required.
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 24
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +4
-0+* APMU definitions +*****************************************************************************/ +#define CA15_APMU_BASE 0xe6152000 +#define CA7_APMU_BASE 0xe6151000All these addresses should come from DT. And the driver should be DM capable and live in
drivers/[...]
All PSCI backends for ARMV7 in U-Boot which I was able to found, are located either in arch/arm/cpu/armv7/
or in arch/arm/mach-X. As well as other PSCI backends, this one will be located in a separate secure section and acts as secure monitor,
so it will be still alive, when U-Boot is gone away. Do we really want this one to go into drivers?
Quoted 6 lines
Quoted 6 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+/***************************************************************************** +* Functions which intended to be called from PSCI handlers. These functions +* marked as __secure and are placed in .secure section. +*****************************************************************************/ +void __secure r8a7790_apmu_power_on(int cpu) +{
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 154
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+int cluster =r8a7790_cluster_id (cpu); +u32 apmu_base; + + apmu_base = cluster ==0 ?CA15_APMU_BASE :CA7_APMU_BASE ; + +/* Request power on */ +writel (BIT (r8a7790_core_id (cpu)), apmu_base +WUPCR_OFFS );
wait_for_bitof some sorts ?
probably yes, will re-use
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 158
Quoted 3 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+/* Wait for APMU to finish */ +while (readl (apmu_base +WUPCR_OFFS )) + ;Can this spin forever ?
I didn't find anything in TRM which describes how long it may take. Linux also doesn't use timeout.
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/platsmp-apmu.c#L46
Shall I add some timeout (probably 1s) in order to be completely safe?
Quoted 63 lines
Quoted 63 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +63
-0+} + +void __secure r8a7790_apmu_power_off(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 apmu_base; + + apmu_base = cluster ==0 ?CA15_APMU_BASE :CA7_APMU_BASE ; + +/* Request Core Standby for next WFI */ +writel (CPUPWR_STANDBY , apmu_base +CPUNCR_OFFS (r8a7790_core_id (cpu))); +} + +void __secure r8a7790_assert_reset(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 mask, magic, rescnt; + + mask =BIT (3 -r8a7790_core_id (cpu)); + magic = cluster ==0 ?CA15RESCNT_CODE :CA7RESCNT_CODE ; + rescnt =RST_BASE + (cluster ==0 ?CA15RESCNT :CA7RESCNT ); +writel ((readl (rescnt) | mask) | magic, rescnt); +} + +void __secure r8a7790_deassert_reset(int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 mask, magic, rescnt; + + mask =BIT (3 -r8a7790_core_id (cpu)); + magic = cluster ==0 ?CA15RESCNT_CODE :CA7RESCNT_CODE ; + rescnt =RST_BASE + (cluster ==0 ?CA15RESCNT :CA7RESCNT ); +writel ((readl (rescnt) & ~mask) | magic, rescnt); +} + +void __secure r8a7790_system_reset(void) +{ +u32 bar; + +/* +* Before configuring internal watchdog timer (RWDT) to reboot system +* we need to re-program BAR registers for the boot CPU to jump to +* bootrom code. Without taking care of, the boot CPU will jump to +* the reset vector previously installed in ICRAM1, since BAR registers +* keep their values after watchdog triggered reset. +*/ + bar = (BOOTROM >>8 ) &0xfffffc00 ; +writel (bar,RST_BASE +CA15BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA15BAR ); +writel (bar,RST_BASE +CA7BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA7BAR ); +dsb (); + +/* Now, configure watchdog timer to reboot the system */ + +/* Trigger reset when counter overflows */ +writel (WDTRSTCR_CODE |0x2 ,RST_BASE +WDTRSTCR ); +dsb (); + +/* Stop counter */ +writel (RWTCSRA_CODE ,RWDT_BASE +RWTCSRA ); + +/* Initialize counter with the highest value */
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 228
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+writel (RWTCNT_CODE |0xffff ,RWDT_BASE +RWTCNT ); + +while (readb (RWDT_BASE +RWTCSRA ) &RWTCSRA_WRFLG ) + ; + +/* Start counter */ +writel (RWTCSRA_CODE |RWTCSRA_TME ,RWDT_BASE +RWTCSRA );This seems to reimplement the reset code that's in U-Boot already. Why ?
Yes. I had to re-implement. Let me describe why.
From my understanding (I may mistake), the PSCI backend code which
lives in secure section should be as lightweight as possible
and shouldn't call any U-Boot routines not marked as __secure, except simple static inline functions.
You can see PSCI implementation for any platform in U-Boot, and only simple "macroses/inlines" are used across all of them.
Even for realizing some delay in code, they have specially implemented something simple. As an example __mdelay() realization here:
https://elixir.bootlin.com/u-boot/v2019.01/source/arch/arm/cpu/armv7/sunxi/psci.c#L61
I know that PMIC (for Lager) and CPLD (for Stout) assist SoC to perform reset. But, I couldn't use that functional here in PSCI backend, as it pulls a lot of code (i2c for PMIC, gpio manipulation for CPLD, etc),
so for that reason (AFAIK the PSCI system reset is a mandatory option) I chose WDT as a entity for doing a reset. This is quite simple and can be used on both boards, what is more that it can be used on other Gen2 SoC if required.
Quoted 84 lines
Quoted 84 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +84
-0+} + +/***************************************************************************** +* Functions which intended to be called from PSCI board initialization. +*****************************************************************************/ +static int sysc_power_up (int scu) +{ +u32 status, chan_offs, isr_bit; +int i, j, ret =0 ; + +if (scu ==CA15_SCU ) { + chan_offs =CA15_SCU_CHAN_OFFS ; + isr_bit =CA15_SCU_ISR_BIT ; + }else { + chan_offs =CA7_SCU_CHAN_OFFS ; + isr_bit =CA7_SCU_ISR_BIT ; + } + +writel (BIT (isr_bit),SYSC_BASE +SYSCISCR ); + +/* Submit power resume request until it was accepted */ +for (i =0 ; i <PWRER_RETRIES ; i++) { +/* Wait until SYSC is ready to accept a power resume request */ +for (j =0 ; j <SYSCSR_RETRIES ; j++) { +if (readl (SYSC_BASE +SYSCSR ) &BIT (1 )) +break ; + +udelay (SYSCSR_DELAY_US ); + } + +if (j ==SYSCSR_RETRIES ) +return -EAGAIN ; + +/* Submit power resume request */ +writel (BIT (0 ),SYSC_BASE + chan_offs +PWRONCR_OFFS ); + +/* Check if power resume request was accepted */ + status =readl (SYSC_BASE + chan_offs +PWRER_OFFS ); +if (!(status &BIT (0 ))) +break ; + +udelay (PWRER_DELAY_US ); + } + +if (i ==PWRER_RETRIES ) +return -EIO ; + +/* Wait until the power resume request has completed */ +for (i =0 ; i <SYSCISR_RETRIES ; i++) { +if (readl (SYSC_BASE +SYSCISR ) &BIT (isr_bit)) +break ; +udelay (SYSCISR_DELAY_US ); + } + +if (i ==SYSCISR_RETRIES ) + ret = -EIO ; + +writel (BIT (isr_bit),SYSC_BASE +SYSCISCR ); + +return ret; +} + +static bool sysc_power_is_off (int scu) +{ +u32 status, chan_offs; + + chan_offs = scu ==CA15_SCU ?CA15_SCU_CHAN_OFFS :CA7_SCU_CHAN_OFFS ; + +/* Check if SCU is in power shutoff state */ + status =readl (SYSC_BASE + chan_offs +PWRSR_OFFS ); +if (status &BIT (0 )) +return true; + +return false; +} + +static void apmu_setup_debug_mode (int cpu) +{ +int cluster =r8a7790_cluster_id (cpu); +u32 apmu_base, reg; + + apmu_base = cluster ==0 ?CA15_APMU_BASE :CA7_APMU_BASE ; + +/*
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 319
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+* Enable reset requests derived from power shutoff to the AP-system +* CPU cores in debug mode. Without taking care of, they may fail to +* resume from the power shutoff state. +*/ + reg =readl (apmu_base +DBGRCR_OFFS ); + reg |=DBGCPUREN |DBGCPUNREN (r8a7790_core_id (cpu)) |DBGCPUPREN ; +writel (reg, apmu_base +DBGRCR_OFFS );
setbits_le32()
Agree, will re-use
Quoted 15 lines
Quoted 15 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +15
-0+} + +/* +* Reset vector for secondary CPUs. +* This will be mapped at address 0 by SBAR register. +* We need _long_ jump to the physical address. +*/ +asm(" .arm\n" +" .align 12\n" +" .globl shmobile_boot_vector\n" +"shmobile_boot_vector:\n" +" ldr r1, 1f\n" +" bx r1\n" +" .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 341
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+" .align 2\n" +" .globl shmobile_boot_fn\n" +"shmobile_boot_fn:\n" +"1: .space 4\n" +" .globl shmobile_boot_size\n" +"shmobile_boot_size:\n" + " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not to mix C and ASM. What do you think about it?
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 345
Quoted 3 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+extern void shmobile_boot_vector (void ); +extern unsigned long shmobile_boot_fn; +extern unsigned long shmobile_boot_size;Are the externs necessary ?
Yes, otherwise, compiler will complain.
I can hide them in a header file. Shall I do that with moving ASM code to a separate file?
Quoted 6 lines
Quoted 6 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus) +{ +int cpu =get_current_cpu (); +int i, ret =0 ; +u32 bar; +
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 359
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+ shmobile_boot_fn = addr; +dsb (); + +/* Install reset vector */ +memcpy_toio ((void __iomem *)ICRAM1 , shmobile_boot_vector, + shmobile_boot_size); +dmb ();Does this take into consideration caches ?
Good question... Probably, I should have added flush_dcache_range() after copy.
Quoted 19 lines
Quoted 19 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +19
-0+/* Setup reset vectors */ + bar = (ICRAM1 >>8 ) &0xfffffc00 ; +writel (bar,RST_BASE +CA15BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA15BAR ); +writel (bar,RST_BASE +CA7BAR ); +writel (bar |SBAR_BAREN ,RST_BASE +CA7BAR ); +dsb (); + +/* Perform setup for debug mode for all CPUs */ +for (i =0 ; i < nr_cpus; i++) +apmu_setup_debug_mode (i); + +/* +* Indicate the completion status of power shutoff/resume procedure +* for CA15/CA7 SCU. +*/ +writel (BIT (CA15_SCU_ISR_BIT ) |BIT (CA7_SCU_ISR_BIT ), +SYSC_BASE +SYSCIER ); +
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 386
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+/* Power on CA15/CA7 SCU */ +if (sysc_power_is_off (CA15_SCU )) + ret +=sysc_power_up (CA15_SCU ); +if (sysc_power_is_off (CA7_SCU )) + ret +=sysc_power_up (CA7_SCU ); +if (ret) +printf ("warning: some of secondary CPUs may not boot\n" );"some" is not very useful for debugging,.
OK, will provide more concrete output.
Quoted 13 lines
Quoted 13 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +13
-0+/* Keep secondary CPUs in reset */ +for (i =0 ; i < nr_cpus; i++) { +/* Make sure that we don't reset boot CPU */ +if (i == cpu) +continue ; + +r8a7790_assert_reset (i); + } + +/* +* Enable snoop requests and DVM message requests for slave interfaces +* S4 (CA7) and S3 (CA15). +*/
Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 407
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+writel (readl (CCI_BASE +CCI_SLAVE3 +CCI_SNOOP ) |CCI_ENABLE_REQ , +CCI_BASE +CCI_SLAVE3 +CCI_SNOOP ); +writel (readl (CCI_BASE +CCI_SLAVE4 +CCI_SNOOP ) |CCI_ENABLE_REQ , +CCI_BASE +CCI_SLAVE4 +CCI_SNOOP ); +/* Wait for pending bit low */ +while (readl (CCI_BASE +CCI_STATUS )) + ;can this spin forever ?
Paragraph "3.3.4 Status Register" in "ARM CoreLink™CCI-400 Cache Coherent Interconnect" document says nothing
about possibility to spin forever. Just next:
"After writing to the snoop or DVM enable bits, the controller must wait for the register write to
complete, then test that the change_pending bit is LOW before it turns an attached device on or off."
Quoted 286 lines
Quoted 286 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +1
-0+}arch/arm/mach-rmobile/pm-r8a7790.h new file +72
-0@@ -0,0 +1,72 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (C) 2018 EPAM Systems Inc. +*/ + +#ifndef __PM_R8A7790_H__ +#define __PM_R8A7790_H__ + +#include <linux/types.h> + +void r8a7790_apmu_power_on (int cpu); +void r8a7790_apmu_power_off (int cpu); +void r8a7790_assert_reset (int cpu); +void r8a7790_deassert_reset (int cpu); + +void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus); +void r8a7790_system_reset (void ); + +#define R8A7790_NR_CLUSTERS 2 +#define R8A7790_NR_CPUS_PER_CLUSTER 4 + +/* Convert linear CPU index to core/cluster ID */ +#define r8a7790_cluster_id (cpu) ((cpu) / R8A7790_NR_CPUS_PER_CLUSTER) +#define r8a7790_core_id (cpu) ((cpu) % R8A7790_NR_CPUS_PER_CLUSTER) + +#define MPIDR_AFFLVL_MASK GENMASK(7, 0) +#define MPIDR_AFF0_SHIFT 0 +#define MPIDR_AFF1_SHIFT 8 + +/* All functions are inline so that they can be called from .secure section. */ + +/* +* Convert CPU ID in MPIDR format to linear CPU index. +* +* Below the possible CPU IDs and corresponding CPU indexes: +* CPU ID CPU index +* 0x80000000 - 0x00000000 +* 0x80000001 - 0x00000001 +* 0x80000002 - 0x00000002 +* 0x80000003 - 0x00000003 +* 0x80000100 - 0x00000004 +* 0x80000101 - 0x00000005 +* 0x80000102 - 0x00000006 +* 0x80000103 - 0x00000007 +*/ +static inline int mpidr_to_cpu_index (u32 mpidr) +{ +u32 cluster_id, cpu_id; + + cluster_id = (mpidr >>MPIDR_AFF1_SHIFT ) &MPIDR_AFFLVL_MASK ; + cpu_id = (mpidr >>MPIDR_AFF0_SHIFT ) &MPIDR_AFFLVL_MASK ; + +if (cluster_id >=R8A7790_NR_CLUSTERS ) +return -1 ; + +if (cpu_id >=R8A7790_NR_CPUS_PER_CLUSTER ) +return -1 ; + +return (cpu_id + (cluster_id *R8A7790_NR_CPUS_PER_CLUSTER )); +} + +/* Return an index of the CPU which performs this call */ +static inline int get_current_cpu (void ) +{ +u32 mpidr; + + asmvolatile ("mrc p15, 0, %0, c0, c0, 5" :"=r" (mpidr)); + +return mpidr_to_cpu_index (mpidr); +} + +#endif /* __PM_R8A7790_H__ */ arch/arm/mach-rmobile/psci.c new file +193
-0@@ -0,0 +1,193 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* This file implements basic PSCI support for Renesas r8a7790 SoC +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Based on arch/arm/mach-uniphier/arm32/psci.c +*/ + +#include <common.h> +#include <linux/psci.h> +#include <asm/io.h> +#include <asm/psci.h> +#include <asm/secure.h> + +#include "pm-r8a7790.h" + +#define R8A7790_PSCI_NR_CPUS 8 +#if R8A7790_PSCI_NR_CPUS >CONFIG_ARMV7_PSCI_NR_CPUS +#error "invalid value for CONFIG_ARMV7_PSCI_NR_CPUS" +#endif + +#define GICC_CTLR_OFFSET 0x2000 + +/* +* The boot CPU is powered on by default, but it's index is not a const +* value. An index the boot CPU has, depends on whether it is CA15 (index 0) +* or CA7 (index 4). +* So, we update state for the boot CPU during PSCI board initialization. +*/ +u8 psci_state[R8A7790_PSCI_NR_CPUS] __secure_data = { +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF }; + +void __secure psci_set_state(int cpu, u8 state) +{ + psci_state[cpu] = state; +dsb (); +isb (); +} + +u32 __secure psci_get_cpu_id(void) +{ +return get_current_cpu (); +} + +void __secure psci_arch_cpu_entry(void) +{ +int cpu =get_current_cpu (); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON ); +} + +int __secure psci_features(u32 function_id, u32 psci_fid) +{ +switch (psci_fid) { +case ARM_PSCI_0_2_FN_PSCI_VERSION : +case ARM_PSCI_0_2_FN_CPU_OFF : +case ARM_PSCI_0_2_FN_CPU_ON : +case ARM_PSCI_0_2_FN_AFFINITY_INFO : +case ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE : +case ARM_PSCI_0_2_FN_SYSTEM_OFF : +case ARM_PSCI_0_2_FN_SYSTEM_RESET : +return 0x0 ; + } + +return ARM_PSCI_RET_NI ; +} + +u32 __secure psci_version(u32 function_id) +{ +return ARM_PSCI_VER_1_0 ; +} + +int __secure psci_affinity_info(u32 function_id, u32 target_affinity, +u32 lowest_affinity_level) +{ +int cpu; + +if (lowest_affinity_level >0 ) +return ARM_PSCI_RET_INVAL ; + + cpu =mpidr_to_cpu_index (target_affinity); +if (cpu ==-1 ) +return ARM_PSCI_RET_INVAL ; + +/* TODO flush cache */ +return psci_state[cpu]; +} + +int __secure psci_migrate_info_type(u32 function_id) +{ +/* Trusted OS is either not present or does not require migration */ +return 2 ; +} + +int __secure psci_cpu_on(u32 function_id, u32 target_cpu, u32 entry_point, +u32 context_id) +{ +int cpu; + + cpu =mpidr_to_cpu_index (target_cpu); +if (cpu ==-1 ) +return ARM_PSCI_RET_INVAL ; + +if (psci_state[cpu] ==PSCI_AFFINITY_LEVEL_ON ) +return ARM_PSCI_RET_ALREADY_ON ; + +if (psci_state[cpu] ==PSCI_AFFINITY_LEVEL_ON_PENDING ) +return ARM_PSCI_RET_ON_PENDING ; + +psci_save (cpu, entry_point, context_id); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON_PENDING ); + +r8a7790_assert_reset (cpu); +r8a7790_apmu_power_on (cpu); +r8a7790_deassert_reset (cpu); + +return ARM_PSCI_RET_SUCCESS ; +} + +int __secure psci_cpu_off(void) +{ +int cpu =get_current_cpu (); + +/* +* Place the CPU interface in a state where it can never make a CPU +* exit WFI as result of an asserted interrupt. +*/ +writel (0 ,CONFIG_ARM_GIC_BASE_ADDRESS +GICC_CTLR_OFFSET ); +dsb (); + +/* Select next sleep mode using the APMU */ +r8a7790_apmu_power_off (cpu); + +/* Do ARM specific CPU shutdown */ +psci_cpu_off_common (); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_OFF ); + +/* Drain the WB before WFI */ +dsb (); + +while (1 ) +wfi (); +} + +void __secure psci_system_reset(u32 function_id) +{ +r8a7790_system_reset (); + +/* Drain the WB before WFI */ +dsb (); + +/* The system is about to be rebooted, so just waiting for this */ +while (1 ) +wfi (); +} + +void __secure psci_system_off(u32 function_id) +{ +/* Drain the WB before WFI */ +dsb (); + +/* +* System Off is not implemented yet, so waiting for powering off +* manually +*/ +while (1 ) +wfi (); +} + +void psci_board_init (void ) +{ +int cpu =get_current_cpu (); + +/* Update state for the boot CPU */ +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON ); + +/* +* Perform needed actions for the secondary CPUs to be ready +* for powering on +*/ +r8a7790_prepare_cpus ((unsigned long )psci_cpu_entry, +R8A7790_PSCI_NR_CPUS ); +}include/configs/lager.h +0
-0@@ -51,4 +51,6 @@/* The PERIPHBASE in the CBAR register is wrong, so override it */ #define CONFIG_ARM_GIC_BASE_ADDRESS 0xf1000000
Quoted 2 lines
include/configs/lager.h line 54
Quoted 1 line
include/configs/lager.h +1
-0+#define CONFIG_ARMV7_PSCI_1_0 Why is this in board code, shouldn't that be in platform code ?
I will move it to "rcar-gen2-common.h"
Quoted 2 lines
[...]
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
Quoted 4 lines · Oleksandr
On 05.02.19 20:55, Marek Vasut wrote:
Hi Marek
Hi,
Quoted 93 lines
Quoted 33 lines · Oleksandr Tyshchenko
Quoted 32 lines
From: Oleksandr Tyshchenko <[email protected]>
Also enable PSCI support for Stout and Lager boards where actually the r8a7790 SoC is installed.
All secondary CPUs will be switched to a non-secure HYP mode after booting.
Signed-off-by Oleksandr Tyshchenko <[email protected]>---
arch/arm/mach-rmobile/Kconfig.32 | 2 + arch/arm/mach-rmobile/Makefile | 6 +arch/arm/mach-rmobile/pm-r8a7790.c| 408
+++++++++++++++++++++++++++++++++++++
arch/arm/mach-rmobile/pm-r8a7790.h| 72 +++++++ arch/arm/mach-rmobile/psci.c | 193 ++++++++++++++++++ include/configs/lager.h | 2 + include/configs/stout.h | 2 +7 files changed, 685 insertions(+)create mode 100644
arch/arm/mach-rmobile/pm-r8a7790.ccreate mode 100644arch/arm/mach-rmobile/pm-r8a7790.hcreate mode 100644arch/arm/mach-rmobile/psci.carch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -78,6 +78,7 @@ config TARGET_LAGERimply
CMD_DM
selectCPU_V7_HAS_NONSEC
selectCPU_V7_HAS_VIRTQuoted 8 lines
Quoted 8 lines
+ select
ARCH_SUPPORT_PSCI
configTARGET_KZM9G
bool "KZM9D board"arch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -119,6 +120,7 @@ config TARGET_STOUTimply
CMD_DM
selectCPU_V7_HAS_NONSEC
selectCPU_V7_HAS_VIRT
+ selectARCH_SUPPORT_PSCITo myself: Move this option under "config R8A7790".
Quoted 40 lines
Quoted 40 lines
endchoice
diff --git a/arch/arm/mach-rmobile/Makefile
b/arch/arm/mach-rmobile/Makefile
index 1f26ada..6f4c513 100644arch/arm/mach-rmobile/Makefile +0
-0@@ -13,3 +13,9 @@ obj-$(CONFIG_SH73A0) += lowlevel_init.ocpu_info-sh73a0.o pfc-sh73a0.o
obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o pfc-r8a7740.o
obj-$(CONFIG_RCAR_GEN2) += lowlevel_init_ca15.o cpu_info-rcar.o obj-$(CONFIG_RCAR_GEN3) += lowlevel_init_gen3.o cpu_info-rcar.o memmap-gen3.oarch/arm/mach-rmobile/Makefile +6
-0+ +ifndef CONFIG_SPL_BUILD +ifdef CONFIG_R8A7790 +obj-$(CONFIG_ARMV7_PSCI) += psci.o pm-r8a7790.o +endif +endifarch/arm/mach-rmobile/pm-r8a7790.c new file +14
-0@@ -0,0 +1,408 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* CPU power management support for Renesas r8a7790 SoC +* +* Contains functions to control ARM Cortex A15/A7 cores and +* related peripherals basically used for PSCI. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Mainly based on Renesas R-Car Gen2 platform code from Linux: +* arch/arm/mach-shmobile/... +*/ + +#include <common.h> Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 20
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+#include <asm/secure.h> +#include <asm/io.h> + +#include "pm-r8a7790.h" + +/***************************************************************************** I'd expect checkpatch to complain about these long lines of asterisks.
Quoted 2 lines
No, there was no complain about it. I have checked. Anyway, I can remove them if required.
Yes please, keep the comment style consistent with the rest of the codebase, which is also the kernel comment style.
Quoted 11 lines
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 24
Quoted 6 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +2
-0+* APMU definitions +*****************************************************************************/
arch/arm/mach-rmobile/pm-r8a7790.c new file +2
-0+#define CA15_APMU_BASE 0xe6152000 +#define CA7_APMU_BASE 0xe6151000All these addresses should come from DT. And the driver should be DM capable and live in
drivers/[...]
Quoted 8 lines
All PSCI backends for ARMV7 in U-Boot which I was able to found, are located either in
arch/arm/cpu/armv7/or in
arch/arm/mach-X. As well as other PSCI backends, this one will be located in a separate secure section and acts as secure monitor,so it will be still alive, when U-Boot is gone away. Do we really want this one to go into drivers?
I'd much prefer it if we stopped adding more stuff to arch/arm/mach-* , but I think we cannot avoid that in this case, can we ?
Quoted 24 lines
Quoted 8 lines
Quoted 8 lines
+/*****************************************************************************
+ * Functions which intended to be called from PSCI handlers. These functions
+ * marked as__secureand are placed in .secure section.
+ *****************************************************************************/Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 154
Quoted 9 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +9
-0+void __secure r8a7790_apmu_power_on(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* Request power on */ + writel(BIT(r8a7790_core_id(cpu)), apmu_base + WUPCR_OFFS);
wait_for_bitof some sorts ?probably yes, will re-use
Quoted 4 lines
Quoted 3 lines
+ /* Wait for APMU to finish */
+ while (readl(apmu_base + WUPCR_OFFS))
+ ;Can this spin forever ?
Quoted 7 lines
I didn't find anything in TRM which describes how long it may take. Linux also doesn't use timeout.
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/platsmp-apmu.c#L46
Shall I add some timeout (probably 1s) in order to be completely safe?
I think so, because if you start spinning in here forever, the system will just completely freeze without any way of recovering. I don't think that's what you want to happen while using virtualization, right ?
Quoted 83 lines
Quoted 66 lines
Quoted 66 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +11
-0+} + +void __secure r8a7790_apmu_power_off(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* Request Core Standby for next WFI */ + writel(CPUPWR_STANDBY, apmu_base +CPUNCR_OFFS(r8a7790_core_id(cpu)));
arch/arm/mach-rmobile/pm-r8a7790.c new file +30
-0+} + +void __secure r8a7790_assert_reset(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 mask, magic, rescnt; + + mask = BIT(3 - r8a7790_core_id(cpu)); + magic = cluster == 0 ? CA15RESCNT_CODE : CA7RESCNT_CODE; + rescnt = RST_BASE + (cluster == 0 ? CA15RESCNT : CA7RESCNT); + writel((readl(rescnt) | mask) | magic, rescnt); +} + +void __secure r8a7790_deassert_reset(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 mask, magic, rescnt; + + mask = BIT(3 - r8a7790_core_id(cpu)); + magic = cluster == 0 ? CA15RESCNT_CODE : CA7RESCNT_CODE; + rescnt = RST_BASE + (cluster == 0 ? CA15RESCNT : CA7RESCNT); + writel((readl(rescnt) & ~mask) | magic, rescnt); +} + +void __secure r8a7790_system_reset(void) +{ + u32 bar; + + /* +* Before configuring internal watchdog timer (RWDT) to reboot system
+ * we need to re-program BAR registers for the boot CPU to jump to + * bootrom code. Without taking care of, the boot CPU will jump to + * the reset vector previously installed in ICRAM1, since BAR registers
+ * keep their values after watchdog triggered reset.
+ */
+ bar = (BOOTROM >> 8) &0xfffffc00;
+writel(bar, RST_BASE + CA15BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA15BAR);
+writel(bar, RST_BASE + CA7BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA7BAR);
+dsb();arch/arm/mach-rmobile/pm-r8a7790.c new file +11
-0+ + /* Now, configure watchdog timer to reboot the system */ + + /* Trigger reset when counter overflows */ + writel(WDTRSTCR_CODE | 0x2, RST_BASE + WDTRSTCR); + dsb(); + + /* Stop counter */ + writel(RWTCSRA_CODE, RWDT_BASE + RWTCSRA); + + /* Initialize counter with the highest value */Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 228
Quoted 7 lines
+
writel(RWTCNT_CODE | 0xffff, RWDT_BASE + RWTCNT);arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+ + while (readb(RWDT_BASE + RWTCSRA) & RWTCSRA_WRFLG) + ; + + /* Start counter */ + writel(RWTCSRA_CODE | RWTCSRA_TME, RWDT_BASE + RWTCSRA);This seems to reimplement the reset code that's in U-Boot already. Why ?
Yes. I had to re-implement. Let me describe why.
From my understanding (I may mistake), the PSCI backend code which lives in secure section should be as lightweight as possible
and shouldn't call any U-Boot routines not marked as
__secure, except simple static inline functions.
Quoted 7 lines
You can see PSCI implementation for any platform in U-Boot, and only simple "macroses/inlines" are used across all of them.
Even for realizing some delay in code, they have specially implemented something simple. As an example
__mdelay()realization here:https://elixir.bootlin.com/u-boot/v2019.01/source/arch/arm/cpu/armv7/sunxi/psci.c#L61
Can the U-Boot code be refactored somehow to avoid the duplication ?
Quoted 3 lines
I know that PMIC (for Lager) and CPLD (for Stout) assist SoC to perform reset. But, I couldn't use that functional here in PSCI backend, as it pulls a lot of code (i2c for PMIC, gpio manipulation for CPLD, etc),
How can the reset work properly if the CPLD/PMIC isn't even used then ?
Quoted 133 lines
so for that reason (AFAIK the PSCI system reset is a mandatory option) I chose WDT as a entity for doing a reset. This is quite simple and can be used on both boards, what is more that it can be used on other Gen2 SoC if required.
Quoted 91 lines
Quoted 91 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +4
-0+} + +/***************************************************************************** +* Functions which intended to be called from PSCI board initialization.
+ *****************************************************************************/arch/arm/mach-rmobile/pm-r8a7790.c new file +62
-0+static int sysc_power_up (int scu) +{ + u32 status, chan_offs, isr_bit; + int i, j, ret = 0; + + if (scu == CA15_SCU) { + chan_offs = CA15_SCU_CHAN_OFFS; + isr_bit = CA15_SCU_ISR_BIT; + } else { + chan_offs = CA7_SCU_CHAN_OFFS; + isr_bit = CA7_SCU_ISR_BIT; + } + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + /* Submit power resume request until it was accepted */ + for (i = 0; i < PWRER_RETRIES; i++) { + /* Wait until SYSC is ready to accept a power resume request */ + for (j = 0; j < SYSCSR_RETRIES; j++) { + if (readl(SYSC_BASE + SYSCSR) & BIT(1)) + break; + + udelay(SYSCSR_DELAY_US); + } + + if (j == SYSCSR_RETRIES) + return -EAGAIN; + + /* Submit power resume request */ + writel(BIT(0), SYSC_BASE + chan_offs + PWRONCR_OFFS); + + /* Check if power resume request was accepted */ + status = readl(SYSC_BASE + chan_offs + PWRER_OFFS); + if (!(status & BIT(0))) + break; + + udelay(PWRER_DELAY_US); + } + + if (i == PWRER_RETRIES) + return -EIO; + + /* Wait until the power resume request has completed */ + for (i = 0; i < SYSCISR_RETRIES; i++) { + if (readl(SYSC_BASE + SYSCISR) & BIT(isr_bit)) + break; + udelay(SYSCISR_DELAY_US); + } + + if (i == SYSCISR_RETRIES) + ret = -EIO; + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + return ret; +} + +static bool sysc_power_is_off (int scu) +{ + u32 status, chan_offs; + + chan_offs = scu == CA15_SCU ? CA15_SCU_CHAN_OFFS :
CA7_SCU_CHAN_OFFS;arch/arm/mach-rmobile/pm-r8a7790.c new file +18
-0+ + /* Check if SCU is in power shutoff state */ + status = readl(SYSC_BASE + chan_offs + PWRSR_OFFS); + if (status & BIT(0)) + return true; + + return false; +} + +static void apmu_setup_debug_mode (int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base, reg; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* +* Enable reset requests derived from power shutoff to the AP-system
Quoted 8 lines
Quoted 7 lines
+ * CPU cores in debug mode. Without taking care of, they may fail to
+ * resume from the power shutoff state.
+ */
+ reg =readl(apmu_base + DBGRCR_OFFS);
+ reg |= DBGCPUREN | DBGCPUNREN(r8a7790_core_id(cpu)) | DBGCPUPREN; +writel(reg, apmu_base + DBGRCR_OFFS);
setbits_le32()Agree, will re-use
Quoted 15 lines
Quoted 15 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +15
-0+} + +/* +* Reset vector for secondary CPUs. +* This will be mapped at address 0 by SBAR register. +* We need _long_ jump to the physical address. +*/ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n" + " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"Quoted 8 lines
Quoted 7 lines
+ " .align 2\n"
+ " .globl shmobile_boot_fn\n"
+ "shmobile_boot_fn:\n"
+ "1: .space 4\n"
+ " .globl shmobile_boot_size\n"
+ "shmobile_boot_size:\n"
+ " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
Quoted 7 lines
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not to mix C and ASM. What do you think about it?
U-Boot already has a reset vector code, can't that be reused ?
Quoted 9 lines
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 345
Quoted 3 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+extern void shmobile_boot_vector (void ); +extern unsigned long shmobile_boot_fn; +extern unsigned long shmobile_boot_size;Are the externs necessary ?
Yes, otherwise, compiler will complain.
I can hide them in a header file. Shall I do that with moving ASM code to a separate file?
Only if you cannot reuse the U-Boot reset vector ones , which I think you can ?
Quoted 74 lines
Quoted 6 lines
Quoted 6 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus) +{ + int cpu = get_current_cpu(); + int i, ret = 0; + u32 bar; +Quoted 8 lines
Quoted 7 lines
+
shmobile_boot_fn= addr;
+dsb();
+
+ /* Install reset vector */
+memcpy_toio((void __iomem *)ICRAM1, shmobile_boot_vector, + shmobile_boot_size);
+dmb();Does this take into consideration caches ?
Good question... Probably, I should have added
flush_dcache_range()after copy.Quoted 19 lines
Quoted 19 lines
+ /* Setup reset vectors */
+ bar = (ICRAM1 >> 8) &0xfffffc00;
+writel(bar, RST_BASE + CA15BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA15BAR); +writel(bar, RST_BASE + CA7BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA7BAR); +dsb();arch/arm/mach-rmobile/pm-r8a7790.c new file +12
-0+ + /* Perform setup for debug mode for all CPUs */ + for (i = 0; i < nr_cpus; i++) + apmu_setup_debug_mode(i); + + /* + * Indicate the completion status of power shutoff/resume procedure + * for CA15/CA7 SCU. + */ + writel(BIT(CA15_SCU_ISR_BIT) | BIT(CA7_SCU_ISR_BIT), + SYSC_BASE + SYSCIER); +Quoted 8 lines
Quoted 7 lines
+ /* Power on CA15/CA7 SCU */
+ if (sysc_power_is_off(CA15_SCU))
+ ret +=sysc_power_up(CA15_SCU);
+ if (sysc_power_is_off(CA7_SCU))
+ ret +=sysc_power_up(CA7_SCU);
+ if (ret)
+printf("warning: some of secondary CPUs may not boot\n");"some" is not very useful for debugging,.
OK, will provide more concrete output.
Quoted 14 lines
Quoted 14 lines
+ /* Keep secondary CPUs in reset */
+ for (i = 0; i <nr_cpus; i++) {
+ /* Make sure that we don't reset boot CPU */ + if (i == cpu)
+ continue;arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+ + r8a7790_assert_reset(i); + } + + /* +* Enable snoop requests and DVM message requests for slave interfaces
+ * S4 (CA7) and S3 (CA15).
+ */Quoted 8 lines
Quoted 7 lines
+ writel(readl(CCI_BASE +
CCI_SLAVE3+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE3+CCI_SNOOP);
+ writel(readl(CCI_BASE +CCI_SLAVE4+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE4+CCI_SNOOP);
+ /* Wait for pending bit low */
+ while (readl(CCI_BASE + CCI_STATUS))
+ ;can this spin forever ?
Paragraph "3.3.4 Status Register" in "ARM CoreLink™CCI-400 Cache Coherent Interconnect" document says nothing
Quoted 6 lines
about possibility to spin forever. Just next:
"After writing to the snoop or DVM enable bits, the controller must wait for the register write to
complete, then test that thechange_pendingbit is LOW before it turns an attached device on or off."
So what if this code spins forever, will this also completely hang Linux which calls this code ?
[...]
Signature · 2 lines
Best regards, Marek Vasut
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
Quoted 5 lines · Marek Vasut
Quoted 3 lines · Oleksandr
On 05.02.19 20:55, Marek Vasut wrote:
Hi Marek
Hi,
Hi Marek
Quoted 91 lines
Quoted 91 lines
Quoted 33 lines · Oleksandr Tyshchenko
Quoted 32 lines
From: Oleksandr Tyshchenko <[email protected]>
Also enable PSCI support for Stout and Lager boards where actually the r8a7790 SoC is installed.
All secondary CPUs will be switched to a non-secure HYP mode after booting.
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/Kconfig.32 | 2 + arch/arm/mach-rmobile/Makefile | 6 + arch/arm/mach-rmobile/pm-r8a7790.c | 408 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/pm-r8a7790.h | 72 +++++++ arch/arm/mach-rmobile/psci.c | 193 ++++++++++++++++++ include/configs/lager.h | 2 + include/configs/stout.h | 2 + 7 files changed, 685 insertions(+)create mode 100644
arch/arm/mach-rmobile/pm-r8a7790.ccreate mode 100644arch/arm/mach-rmobile/pm-r8a7790.hcreate mode 100644arch/arm/mach-rmobile/psci.carch/arm/mach-rmobile/Kconfig.32 +0
-0@@ -78,6 +78,7 @@ config TARGET_LAGER imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRTQuoted 8 lines
arch/arm/mach-rmobile/Kconfig.32 config TARGET_STOUT · line 123
Quoted 8 lines
arch/arm/mach-rmobile/Kconfig.32 +2
-0+ select ARCH_SUPPORT_PSCI config TARGET_KZM9G bool "KZM9D board"@@ -119,6 +120,7 @@ config TARGET_STOUT imply CMD_DM select CPU_V7_HAS_NONSEC select CPU_V7_HAS_VIRT + select ARCH_SUPPORT_PSCITo myself: Move this option under "config R8A7790".
Quoted 48 lines
Quoted 37 lines
arch/arm/mach-rmobile/Kconfig.32 +0
-0endchoice diff --git a/arch/arm/mach-rmobile/Makefileb/arch/arm/mach-rmobile/Makefile
index 1f26ada..6f4c513 100644arch/arm/mach-rmobile/Makefile +0
-0@@ -13,3 +13,9 @@ obj-$(CONFIG_SH73A0) += lowlevel_init.ocpu_info-sh73a0.o pfc-sh73a0.o
obj-$(CONFIG_R8A7740) += lowlevel_init.o cpu_info-r8a7740.o
pfc-r8a7740.o
obj-$(CONFIG_RCAR_GEN2) += lowlevel_init_ca15.o cpu_info-rcar.o obj-$(CONFIG_RCAR_GEN3) += lowlevel_init_gen3.o cpu_info-rcar.o
memmap-gen3.oarch/arm/mach-rmobile/Makefile +6
-0+ +ifndef CONFIG_SPL_BUILD +ifdef CONFIG_R8A7790 +obj-$(CONFIG_ARMV7_PSCI) += psci.o pm-r8a7790.o +endif +endifarch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0@@ -0,0 +1,408 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* CPU power management support for Renesas r8a7790 SoC +* +* Contains functions to control ARM Cortex A15/A7 cores and +* related peripherals basically used for PSCI. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Mainly based on Renesas R-Car Gen2 platform code from Linux: arch/arm/mach-rmobile/pm-r8a7790.c line 20
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+* arch/arm/mach-shmobile/... +*/ + +#include <common.h> +#include <asm/secure.h> +#include <asm/io.h> + +#include "pm-r8a7790.h" + +/***************************************************************************** I'd expect checkpatch to complain about these long lines of asterisks.
Quoted 4 lines
Quoted 2 lines
No, there was no complain about it. I have checked. Anyway, I can remove them if required.
Yes please, keep the comment style consistent with the rest of the codebase, which is also the kernel comment style.
OK, will remove
Quoted 14 lines
Quoted 14 lines
Quoted 11 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 24
Quoted 7 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +2
-0+* APMU definitions +*****************************************************************************/
arch/arm/mach-rmobile/pm-r8a7790.c new file +2
-0+#define CA15_APMU_BASE 0xe6152000 +#define CA7_APMU_BASE 0xe6151000All these addresses should come from DT. And the driver should be DM capable and live in
drivers/[...]
All PSCI backends for ARMV7 in U-Boot which I was able to found, are located either in
arch/arm/cpu/armv7/
Quoted 7 lines
Quoted 5 lines
or in
arch/arm/mach-X. As well as other PSCI backends, this one will be located in a separate secure section and acts as secure monitor,so it will be still alive, when U-Boot is gone away. Do we really want this one to go into drivers?
I'd much prefer it if we stopped adding more stuff to
arch/arm/mach-*, but I think we cannot avoid that in this case, can we ?
I am afraid, we can't avoid.
Quoted 27 lines
Quoted 27 lines
Quoted 9 lines
Quoted 9 lines
+/*****************************************************************************
+ * Functions which intended to be called from PSCI handlers. These functions
+ * marked as__secureand are placed in .secure section.
+ *****************************************************************************/Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 154
Quoted 9 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +9
-0+void __secure r8a7790_apmu_power_on(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* Request power on */ + writel(BIT(r8a7790_core_id(cpu)), apmu_base + WUPCR_OFFS);
wait_for_bitof some sorts ?probably yes, will re-use
Quoted 4 lines
Quoted 3 lines
+ /* Wait for APMU to finish */
+ while (readl(apmu_base + WUPCR_OFFS))
+ ;Can this spin forever ?
I didn't find anything in TRM which describes how long it may take. Linux also doesn't use timeout.
Quoted 6 lines
Quoted 4 lines
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/platsmp-apmu.c#L46
Shall I add some timeout (probably 1s) in order to be completely safe?
I think so, because if you start spinning in here forever, the system will just completely freeze without any way of recovering.
Yes, the CPU executing that PSCI request (SMC) will block here.
Quoted 2 lines
I don't think
that's what you want to happen while using virtualization, right ?
Absolutely, will use timeout.
Quoted 83 lines
Quoted 83 lines
Quoted 67 lines
Quoted 67 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +11
-0+} + +void __secure r8a7790_apmu_power_off(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* Request Core Standby for next WFI */ + writel(CPUPWR_STANDBY, apmu_base +CPUNCR_OFFS(r8a7790_core_id(cpu)));
arch/arm/mach-rmobile/pm-r8a7790.c new file +30
-0+} + +void __secure r8a7790_assert_reset(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 mask, magic, rescnt; + + mask = BIT(3 - r8a7790_core_id(cpu)); + magic = cluster == 0 ? CA15RESCNT_CODE : CA7RESCNT_CODE; + rescnt = RST_BASE + (cluster == 0 ? CA15RESCNT : CA7RESCNT); + writel((readl(rescnt) | mask) | magic, rescnt); +} + +void __secure r8a7790_deassert_reset(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 mask, magic, rescnt; + + mask = BIT(3 - r8a7790_core_id(cpu)); + magic = cluster == 0 ? CA15RESCNT_CODE : CA7RESCNT_CODE; + rescnt = RST_BASE + (cluster == 0 ? CA15RESCNT : CA7RESCNT); + writel((readl(rescnt) & ~mask) | magic, rescnt); +} + +void __secure r8a7790_system_reset(void) +{ + u32 bar; + + /* +* Before configuring internal watchdog timer (RWDT) to reboot system
+ * we need to re-program BAR registers for the boot CPU to jump to + * bootrom code. Without taking care of, the boot CPU will jump to + * the reset vector previously installed in ICRAM1, since BAR registers
+ * keep their values after watchdog triggered reset.
+ */
+ bar = (BOOTROM >> 8) &0xfffffc00;
+writel(bar, RST_BASE + CA15BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA15BAR);
+writel(bar, RST_BASE + CA7BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA7BAR);
+dsb();arch/arm/mach-rmobile/pm-r8a7790.c new file +11
-0+ + /* Now, configure watchdog timer to reboot the system */ + + /* Trigger reset when counter overflows */ + writel(WDTRSTCR_CODE | 0x2, RST_BASE + WDTRSTCR); + dsb(); + + /* Stop counter */ + writel(RWTCSRA_CODE, RWDT_BASE + RWTCSRA); + + /* Initialize counter with the highest value */Quoted 8 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 228
Quoted 7 lines
+
writel(RWTCNT_CODE | 0xffff, RWDT_BASE + RWTCNT);arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+ + while (readb(RWDT_BASE + RWTCSRA) & RWTCSRA_WRFLG) + ; + + /* Start counter */ + writel(RWTCSRA_CODE | RWTCSRA_TME, RWDT_BASE + RWTCSRA);This seems to reimplement the reset code that's in U-Boot already. Why ?
Yes. I had to re-implement. Let me describe why.
From my understanding (I may mistake), the PSCI backend code which lives
in secure section should be as lightweight as possibleand shouldn't call any U-Boot routines not marked as
__secure, except simple static inline functions.
Quoted 8 lines
Quoted 7 lines
You can see PSCI implementation for any platform in U-Boot, and only simple "macroses/inlines" are used across all of them.
Even for realizing some delay in code, they have specially implemented something simple. As an example
__mdelay()realization here:https://elixir.bootlin.com/u-boot/v2019.01/source/arch/arm/cpu/armv7/sunxi/psci.c#L61
Can the U-Boot code be refactored somehow to avoid the duplication ?
Sorry, what duplication you are speaking about?
Quoted 5 lines
Quoted 4 lines
I know that PMIC (for Lager) and CPLD (for Stout) assist SoC to perform reset. But, I couldn't use that functional here in PSCI backend, as it pulls a lot of code (i2c for PMIC, gpio manipulation for CPLD, etc),
How can the reset work properly if the CPLD/PMIC isn't even used then ?
We ask WDT to perform a CPU reset, although this is not the same reset as an external reset from CPLD/PMIC,
but, why not use it, if we don't have alternative? This is certainly better than nothing, I think.
Actually, we ask WDT to do what it is intended to do, and it seems to work properly as the system up and running after WDT reset in 100% cases.
What is more, this PSCI reset implementation could be common for Gen2 SoCs where WDT is present...
Quoted 131 lines
Quoted 131 lines
so for that reason (AFAIK the PSCI system reset is a mandatory option) I chose WDT as a entity for doing a reset. This is quite simple and can be used on both boards, what is more that it can be used on other Gen2 SoC if required.
Quoted 91 lines
Quoted 91 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +4
-0+} + +/***************************************************************************** +* Functions which intended to be called from PSCI board initialization.
+ *****************************************************************************/arch/arm/mach-rmobile/pm-r8a7790.c new file +62
-0+static int sysc_power_up (int scu) +{ + u32 status, chan_offs, isr_bit; + int i, j, ret = 0; + + if (scu == CA15_SCU) { + chan_offs = CA15_SCU_CHAN_OFFS; + isr_bit = CA15_SCU_ISR_BIT; + } else { + chan_offs = CA7_SCU_CHAN_OFFS; + isr_bit = CA7_SCU_ISR_BIT; + } + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + /* Submit power resume request until it was accepted */ + for (i = 0; i < PWRER_RETRIES; i++) { + /* Wait until SYSC is ready to accept a power resume request */ + for (j = 0; j < SYSCSR_RETRIES; j++) { + if (readl(SYSC_BASE + SYSCSR) & BIT(1)) + break; + + udelay(SYSCSR_DELAY_US); + } + + if (j == SYSCSR_RETRIES) + return -EAGAIN; + + /* Submit power resume request */ + writel(BIT(0), SYSC_BASE + chan_offs + PWRONCR_OFFS); + + /* Check if power resume request was accepted */ + status = readl(SYSC_BASE + chan_offs + PWRER_OFFS); + if (!(status & BIT(0))) + break; + + udelay(PWRER_DELAY_US); + } + + if (i == PWRER_RETRIES) + return -EIO; + + /* Wait until the power resume request has completed */ + for (i = 0; i < SYSCISR_RETRIES; i++) { + if (readl(SYSC_BASE + SYSCISR) & BIT(isr_bit)) + break; + udelay(SYSCISR_DELAY_US); + } + + if (i == SYSCISR_RETRIES) + ret = -EIO; + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + return ret; +} + +static bool sysc_power_is_off (int scu) +{ + u32 status, chan_offs; + + chan_offs = scu == CA15_SCU ? CA15_SCU_CHAN_OFFS :
CA7_SCU_CHAN_OFFS;arch/arm/mach-rmobile/pm-r8a7790.c new file +18
-0+ + /* Check if SCU is in power shutoff state */ + status = readl(SYSC_BASE + chan_offs + PWRSR_OFFS); + if (status & BIT(0)) + return true; + + return false; +} + +static void apmu_setup_debug_mode (int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base, reg; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* +* Enable reset requests derived from power shutoff to the AP-system
Quoted 8 lines
Quoted 7 lines
+ * CPU cores in debug mode. Without taking care of, they may fail to
+ * resume from the power shutoff state.
+ */
+ reg =readl(apmu_base + DBGRCR_OFFS);
+ reg |= DBGCPUREN | DBGCPUNREN(r8a7790_core_id(cpu)) | DBGCPUPREN; +writel(reg, apmu_base + DBGRCR_OFFS);
setbits_le32()Agree, will re-use
Quoted 15 lines
Quoted 15 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +15
-0+} + +/* +* Reset vector for secondary CPUs. +* This will be mapped at address 0 by SBAR register. +* We need _long_ jump to the physical address. +*/ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n" + " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"Quoted 8 lines
Quoted 7 lines
+ " .align 2\n"
+ " .globl shmobile_boot_fn\n"
+ "shmobile_boot_fn:\n"
+ "1: .space 4\n"
+ " .globl shmobile_boot_size\n"
+ "shmobile_boot_size:\n"
+ " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
Quoted 8 lines
Quoted 7 lines
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not to mix C and ASM. What do you think about it?
U-Boot already has a reset vector code, can't that be reused ?
I don't think. Being honest, I couldn't find an obvious way how to reuse (I assume you meant arch/arm/cpu/armv7/start.S).
The newly turned on secondary CPU entry should be common "psci_cpu_entry", which does proper things.
And this reset vector is just "a small piece of code" to be located in on-chip RAM (with limited size) and used for the jump stub...
Quoted 11 lines
Quoted 9 lines
Quoted 5 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 345
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+extern void shmobile_boot_vector (void ); +extern unsigned long shmobile_boot_fn; +extern unsigned long shmobile_boot_size;Are the externs necessary ?
Yes, otherwise, compiler will complain.
I can hide them in a header file. Shall I do that with moving ASM code to a separate file?
Only if you cannot reuse the U-Boot reset vector ones , which I think you can ?
I tried to explain above, why I can't reuse. So, if you and other reviewers OK with it,
I will move it to a separate file in V2.
Quoted 74 lines
Quoted 74 lines
Quoted 15 lines
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus) +{ + int cpu = get_current_cpu();arch/arm/mach-rmobile/pm-r8a7790.c line 359
Quoted 10 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +10
-0+ int i, ret = 0; + u32 bar; + + shmobile_boot_fn = addr; + dsb(); + + /* Install reset vector */ + memcpy_toio((void __iomem *)ICRAM1, shmobile_boot_vector, + shmobile_boot_size); + dmb();Does this take into consideration caches ?
Good question... Probably, I should have added
flush_dcache_range()after copy.Quoted 19 lines
Quoted 19 lines
+ /* Setup reset vectors */
+ bar = (ICRAM1 >> 8) &0xfffffc00;
+writel(bar, RST_BASE + CA15BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA15BAR); +writel(bar, RST_BASE + CA7BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA7BAR); +dsb();arch/arm/mach-rmobile/pm-r8a7790.c new file +12
-0+ + /* Perform setup for debug mode for all CPUs */ + for (i = 0; i < nr_cpus; i++) + apmu_setup_debug_mode(i); + + /* + * Indicate the completion status of power shutoff/resume procedure + * for CA15/CA7 SCU. + */ + writel(BIT(CA15_SCU_ISR_BIT) | BIT(CA7_SCU_ISR_BIT), + SYSC_BASE + SYSCIER); +Quoted 8 lines
Quoted 7 lines
+ /* Power on CA15/CA7 SCU */
+ if (sysc_power_is_off(CA15_SCU))
+ ret +=sysc_power_up(CA15_SCU);
+ if (sysc_power_is_off(CA7_SCU))
+ ret +=sysc_power_up(CA7_SCU);
+ if (ret)
+printf("warning: some of secondary CPUs may not boot\n");"some" is not very useful for debugging,.
OK, will provide more concrete output.
Quoted 14 lines
Quoted 14 lines
+ /* Keep secondary CPUs in reset */
+ for (i = 0; i <nr_cpus; i++) {
+ /* Make sure that we don't reset boot CPU */ + if (i == cpu)
+ continue;arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+ + r8a7790_assert_reset(i); + } + + /* +* Enable snoop requests and DVM message requests for slave interfaces
+ * S4 (CA7) and S3 (CA15).
+ */Quoted 8 lines
Quoted 7 lines
+ writel(readl(CCI_BASE +
CCI_SLAVE3+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE3+CCI_SNOOP);
+ writel(readl(CCI_BASE +CCI_SLAVE4+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE4+CCI_SNOOP);
+ /* Wait for pending bit low */
+ while (readl(CCI_BASE + CCI_STATUS))
+ ;can this spin forever ?
Paragraph "3.3.4 Status Register" in "ARM CoreLink™CCI-400 Cache Coherent Interconnect" document says nothing
about possibility to spin forever. Just next:
Quoted 7 lines
Quoted 4 lines
"After writing to the snoop or DVM enable bits, the controller must wait for the register write to
complete, then test that thechange_pendingbit is LOW before it turns an attached device on or off."So what if this code spins forever, will this also completely hang Linux which calls this code ?
[...]
In this case, no. This is PSCI board initialization code, which is being executed while we are still in U-Boot.
Unlike r8a7790_apmu_power_on()/r8a7790_apmu_power_off() functions, which are indented to be called from PSCI handlers (at runtime), when the "main" U-Boot is gone away.
If this code spins forever, U-Boot will get stuck before even starting Linux/Hypervisor.
Probably, it would be better to add safe timeout (~1s) here as well.
Quoted 1 line
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
On 2/11/19 9:10 PM, Oleksandr wrote:
[...]
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
Yes. I had to re-implement. Let me describe why.
From my understanding (I may mistake), the PSCI backend code which lives
in secure section should be as lightweight as possibleand shouldn't call any U-Boot routines not marked as
__secure, except simple static inline functions.You can see PSCI implementation for any platform in U-Boot, and only simple "macroses/inlines" are used across all of them.
Quoted 8 lines
Quoted 6 lines
Quoted 5 lines
Even for realizing some delay in code, they have specially implemented something simple. As an example
__mdelay()realization here:https://elixir.bootlin.com/u-boot/v2019.01/source/arch/arm/cpu/armv7/sunxi/psci.c#L61
Can the U-Boot code be refactored somehow to avoid the duplication ?
Sorry, what duplication you are speaking about?
It is my impression that we're reimplementing code we already have either in drivers/ or in Linux, again, in arch/arm/ . Isn't it the case ?
Quoted 11 lines
Quoted 4 lines
Quoted 3 lines
I know that PMIC (for Lager) and CPLD (for Stout) assist SoC to perform reset. But, I couldn't use that functional here in PSCI backend, as it pulls a lot of code (i2c for PMIC, gpio manipulation for CPLD, etc),
How can the reset work properly if the CPLD/PMIC isn't even used then ?
We ask WDT to perform a CPU reset, although this is not the same reset as an external reset from CPLD/PMIC,
but, why not use it, if we don't have alternative? This is certainly better than nothing, I think.
Do we need to do a full board reset in this case ?
Quoted 145 lines
Actually, we ask WDT to do what it is intended to do, and it seems to work properly as the system up and running after WDT reset in 100% cases.
What is more, this PSCI reset implementation could be common for Gen2 SoCs where WDT is present...
Quoted 138 lines
Quoted 138 lines
so for that reason (AFAIK the PSCI system reset is a mandatory option) I chose WDT as a entity for doing a reset. This is quite simple and can be used on both boards, what is more that it can be used on other Gen2 SoC if required.
Quoted 94 lines
Quoted 94 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +4
-0+} + +/***************************************************************************** +* Functions which intended to be called from PSCI board initialization.
+ *****************************************************************************/arch/arm/mach-rmobile/pm-r8a7790.c new file +18
-0+static int sysc_power_up (int scu) +{ + u32 status, chan_offs, isr_bit; + int i, j, ret = 0; + + if (scu == CA15_SCU) { + chan_offs = CA15_SCU_CHAN_OFFS; + isr_bit = CA15_SCU_ISR_BIT; + } else { + chan_offs = CA7_SCU_CHAN_OFFS; + isr_bit = CA7_SCU_ISR_BIT; + } + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + /* Submit power resume request until it was accepted */ + for (i = 0; i < PWRER_RETRIES; i++) { + /* Wait until SYSC is ready to accept a power resumerequest */
+ for (j = 0; j <SYSCSR_RETRIES; j++) { + if (readl(SYSC_BASE + SYSCSR)& BIT(1)) + break;arch/arm/mach-rmobile/pm-r8a7790.c new file +41
-0+ + udelay(SYSCSR_DELAY_US); + } + + if (j == SYSCSR_RETRIES) + return -EAGAIN; + + /* Submit power resume request */ + writel(BIT(0), SYSC_BASE + chan_offs + PWRONCR_OFFS); + + /* Check if power resume request was accepted */ + status = readl(SYSC_BASE + chan_offs + PWRER_OFFS); + if (!(status & BIT(0))) + break; + + udelay(PWRER_DELAY_US); + } + + if (i == PWRER_RETRIES) + return -EIO; + + /* Wait until the power resume request has completed */ + for (i = 0; i < SYSCISR_RETRIES; i++) { + if (readl(SYSC_BASE + SYSCISR) & BIT(isr_bit)) + break; + udelay(SYSCISR_DELAY_US); + } + + if (i == SYSCISR_RETRIES) + ret = -EIO; + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + return ret; +} + +static bool sysc_power_is_off (int scu) +{ + u32 status, chan_offs; + + chan_offs = scu == CA15_SCU ? CA15_SCU_CHAN_OFFS :
CA7_SCU_CHAN_OFFS;arch/arm/mach-rmobile/pm-r8a7790.c new file +18
-0+ + /* Check if SCU is in power shutoff state */ + status = readl(SYSC_BASE + chan_offs + PWRSR_OFFS); + if (status & BIT(0)) + return true; + + return false; +} + +static void apmu_setup_debug_mode (int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base, reg; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* +* Enable reset requests derived from power shutoff to the AP-system
Quoted 8 lines
Quoted 7 lines
+ * CPU cores in debug mode. Without taking care of, they may fail to
+ * resume from the power shutoff state.
+ */
+ reg =readl(apmu_base + DBGRCR_OFFS);
+ reg |= DBGCPUREN | DBGCPUNREN(r8a7790_core_id(cpu)) | DBGCPUPREN; +writel(reg, apmu_base + DBGRCR_OFFS);
setbits_le32()Agree, will re-use
Quoted 15 lines
Quoted 15 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +15
-0+} + +/* +* Reset vector for secondary CPUs. +* This will be mapped at address 0 by SBAR register. +* We need _long_ jump to the physical address. +*/ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n" + " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"Quoted 8 lines
Quoted 7 lines
+ " .align 2\n"
+ " .globl shmobile_boot_fn\n"
+ "shmobile_boot_fn:\n"
+ "1: .space 4\n"
+ " .globl shmobile_boot_size\n"
+ "shmobile_boot_size:\n"
+ " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Quoted 8 lines
Quoted 5 lines
Quoted 4 lines
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not to mix C and ASM. What do you think about it?
U-Boot already has a reset vector code, can't that be reused ?
I don't think. Being honest, I couldn't find an obvious way how to reuse (I assume you meant
arch/arm/cpu/armv7/start.S).
Maybe it needs some additional work first ?
It seems Altera socfpga somehow uses the U-Boot reset vectors for PSCI, so it should at least be possible.
Quoted 5 lines
The newly turned on secondary CPU entry should be common "
psci_cpu_entry", which does proper things.And this reset vector is just "a small piece of code" to be located in on-chip RAM (with limited size) and used for the jump stub...
We already have the SPL reset vectors in SRAM, maybe that can be recycled somehow ?
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines
arch/arm/mach-rmobile/pm-r8a7790.c line 345
Quoted 3 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +3
-0+extern void shmobile_boot_vector (void ); +extern unsigned long shmobile_boot_fn; +extern unsigned long shmobile_boot_size;Are the externs necessary ?
Yes, otherwise, compiler will complain.
I can hide them in a header file. Shall I do that with moving ASM code to a separate file?
Quoted 7 lines
Quoted 2 lines
Only if you cannot reuse the U-Boot reset vector ones , which I think you can ?
I tried to explain above, why I can't reuse. So, if you and other reviewers OK with it,
I will move it to a separate file in V2.
I don't quite see why it's a problem to use the U-Boot reset vectors. Sure, it might be needed to adjust that code first if it cannot be used as-is.
Quoted 86 lines
Quoted 74 lines
Quoted 74 lines
Quoted 6 lines
Quoted 6 lines
arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+void r8a7790_prepare_cpus (unsigned long addr,u32 nr_cpus) +{ + int cpu = get_current_cpu(); + int i, ret = 0; + u32 bar; +Quoted 8 lines
Quoted 7 lines
+
shmobile_boot_fn= addr;
+dsb();
+
+ /* Install reset vector */
+memcpy_toio((void __iomem *)ICRAM1, shmobile_boot_vector, + shmobile_boot_size);
+dmb();Does this take into consideration caches ?
Good question... Probably, I should have added
flush_dcache_range()after copy.Quoted 20 lines
Quoted 20 lines
+ /* Setup reset vectors */
+ bar = (ICRAM1 >> 8) &0xfffffc00;
+writel(bar, RST_BASE + CA15BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA15BAR); +writel(bar, RST_BASE + CA7BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA7BAR); +dsb();arch/arm/mach-rmobile/pm-r8a7790.c new file +7
-0+ + /* Perform setup for debug mode for all CPUs */ + for (i = 0; i < nr_cpus; i++) + apmu_setup_debug_mode(i); + + /* +* Indicate the completion status of power shutoff/resume procedure
+ * for CA15/CA7 SCU.
+ */
+writel(BIT(CA15_SCU_ISR_BIT) | BIT(CA7_SCU_ISR_BIT), + SYSC_BASE + SYSCIER);
+Quoted 8 lines
Quoted 7 lines
+ /* Power on CA15/CA7 SCU */
+ if (sysc_power_is_off(CA15_SCU))
+ ret +=sysc_power_up(CA15_SCU);
+ if (sysc_power_is_off(CA7_SCU))
+ ret +=sysc_power_up(CA7_SCU);
+ if (ret)
+printf("warning: some of secondary CPUs may not boot\n");"some" is not very useful for debugging,.
OK, will provide more concrete output.
Quoted 14 lines
Quoted 14 lines
+ /* Keep secondary CPUs in reset */
+ for (i = 0; i <nr_cpus; i++) {
+ /* Make sure that we don't reset boot CPU */ + if (i == cpu)
+ continue;arch/arm/mach-rmobile/pm-r8a7790.c new file +6
-0+ + r8a7790_assert_reset(i); + } + + /* +* Enable snoop requests and DVM message requests for slave interfaces
+ * S4 (CA7) and S3 (CA15).
+ */Quoted 8 lines
Quoted 7 lines
+ writel(readl(CCI_BASE +
CCI_SLAVE3+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE3+CCI_SNOOP);
+ writel(readl(CCI_BASE +CCI_SLAVE4+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE4+CCI_SNOOP);
+ /* Wait for pending bit low */
+ while (readl(CCI_BASE + CCI_STATUS))
+ ;can this spin forever ?
Paragraph "3.3.4 Status Register" in "ARM CoreLink™CCI-400 Cache Coherent Interconnect" document says nothing
about possibility to spin forever. Just next:
Quoted 7 lines
Quoted 4 lines
"After writing to the snoop or DVM enable bits, the controller must wait for the register write to
complete, then test that thechange_pendingbit is LOW before it turns an attached device on or off."So what if this code spins forever, will this also completely hang Linux which calls this code ?
[...]In this case, no. This is PSCI board initialization code, which is being executed while we are still in U-Boot.
Quoted 8 lines
Unlike r8a7790_apmu_power_on()/r8a7790_apmu_power_off() functions, which are indented to be called from PSCI handlers (at runtime), when the "main" U-Boot is gone away.
If this code spins forever, U-Boot will get stuck before even starting Linux/Hypervisor.
Probably, it would be better to add safe timeout (~1s) here as well.
I think so.
Signature · 2 lines
Best regards, Marek Vasut
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
On 11.02.19 22:40, Marek Vasut wrote:
Hi
Quoted 19 lines · Oleksandr
[...]
Quoted 15 lines
Quoted 15 lines
Quoted 15 lines
Yes. I had to re-implement. Let me describe why.
From my understanding (I may mistake), the PSCI backend code which
lives
in secure section should be as lightweight as possibleand shouldn't call any U-Boot routines not marked as
__secure, except simple static inline functions.You can see PSCI implementation for any platform in U-Boot, and only simple "macroses/inlines" are used across all of them.
Even for realizing some delay in code, they have specially implemented something simple. As an example
__mdelay()realization here:
Quoted 6 lines
Quoted 4 lines
Quoted 3 lines
Can the U-Boot code be refactored somehow to avoid the duplication ?
Sorry, what duplication you are speaking about?
It is my impression that we're reimplementing code we already have either in
drivers/or in Linux, again, inarch/arm/. Isn't it the case ?
All this code (for preparing, powering up/down the CPUs and related peripherals) which this patch introduces, is new for U-Boot.
But, yes, it is present in Linux (arch/arm/mach-shmobile/...).
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
I know that PMIC (for Lager) and CPLD (for Stout) assist SoC to perform reset. But, I couldn't use that functional here in PSCI backend, as it pulls a lot of code (i2c for PMIC, gpio manipulation for CPLD, etc),
Quoted 8 lines
Quoted 7 lines
Quoted 1 line
How can the reset work properly if the CPLD/PMIC isn't even used then ?
We ask WDT to perform a CPU reset, although this is not the same reset as an external reset from CPLD/PMIC,
but, why not use it, if we don't have alternative? This is certainly better than nothing, I think.
Do we need to do a full board reset in this case ?
After WDT reset CPU will be brought up to bootrom code, then starts executing SPL, U-Boot...
So, we will get all required SoC/Board peripherals re-initialized, I think.
Quoted 148 lines
Quoted 148 lines
Actually, we ask WDT to do what it is intended to do, and it seems to work properly as the system up and running after WDT reset in 100% cases.
What is more, this PSCI reset implementation could be common for Gen2 SoCs where WDT is present...
Quoted 140 lines
Quoted 140 lines
so for that reason (AFAIK the PSCI system reset is a mandatory option) I chose WDT as a entity for doing a reset. This is quite simple and can be used on both boards, what is more that it can be used on other Gen2 SoC if required.
Quoted 94 lines
Quoted 94 lines
(quoted diff) +4
-0+} + +/***************************************************************************** + * Functions which intended to be called from PSCI boardinitialization.
+ *****************************************************************************/(quoted diff) +18
-0+static int sysc_power_up(int scu) +{ + u32 status, chan_offs, isr_bit; + int i, j, ret = 0; + + if (scu == CA15_SCU) { + chan_offs = CA15_SCU_CHAN_OFFS; + isr_bit = CA15_SCU_ISR_BIT; + } else { + chan_offs = CA7_SCU_CHAN_OFFS; + isr_bit = CA7_SCU_ISR_BIT; + } + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + /* Submit power resume request until it was accepted */ + for (i = 0; i < PWRER_RETRIES; i++) { + /* Wait until SYSC is ready to accept a power resumerequest */
+ for (j = 0; j <SYSCSR_RETRIES; j++) { + if (readl(SYSC_BASE + SYSCSR)& BIT(1)) + break;(quoted diff) +41
-0+ + udelay(SYSCSR_DELAY_US); + } + + if (j == SYSCSR_RETRIES) + return -EAGAIN; + + /* Submit power resume request */ + writel(BIT(0), SYSC_BASE + chan_offs + PWRONCR_OFFS); + + /* Check if power resume request was accepted */ + status = readl(SYSC_BASE + chan_offs + PWRER_OFFS); + if (!(status & BIT(0))) + break; + + udelay(PWRER_DELAY_US); + } + + if (i == PWRER_RETRIES) + return -EIO; + + /* Wait until the power resume request has completed */ + for (i = 0; i < SYSCISR_RETRIES; i++) { + if (readl(SYSC_BASE + SYSCISR) & BIT(isr_bit)) + break; + udelay(SYSCISR_DELAY_US); + } + + if (i == SYSCISR_RETRIES) + ret = -EIO; + + writel(BIT(isr_bit), SYSC_BASE + SYSCISCR); + + return ret; +} + +static bool sysc_power_is_off(int scu) +{ + u32 status, chan_offs; + + chan_offs = scu == CA15_SCU ? CA15_SCU_CHAN_OFFS :
CA7_SCU_CHAN_OFFS;(quoted diff) +18
-0+ + /* Check if SCU is in power shutoff state */ + status = readl(SYSC_BASE + chan_offs + PWRSR_OFFS); + if (status & BIT(0)) + return true; + + return false; +} + +static void apmu_setup_debug_mode(int cpu) +{ + int cluster = r8a7790_cluster_id(cpu); + u32 apmu_base, reg; + + apmu_base = cluster == 0 ? CA15_APMU_BASE : CA7_APMU_BASE; + + /* + * Enable reset requests derived from power shutoff to theAP-system
Quoted 8 lines
Quoted 7 lines
+ * CPU cores in debug mode. Without taking care of, they may fail to
+ * resume from the power shutoff state.
+ */
+ reg =readl(apmu_base + DBGRCR_OFFS);
+ reg |= DBGCPUREN | DBGCPUNREN(r8a7790_core_id(cpu)) | DBGCPUPREN; +writel(reg, apmu_base + DBGRCR_OFFS);
setbits_le32()Agree, will re-use
Quoted 15 lines
Quoted 15 lines
(quoted diff) +15
-0+} + +/* + * Reset vector for secondary CPUs. + * This will be mapped at address 0 by SBAR register. + * We need _long_ jump to the physical address. + */ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n" + " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"Quoted 8 lines
Quoted 7 lines
+ " .align 2\n"
+ " .globl shmobile_boot_fn\n"
+ "shmobile_boot_fn:\n"
+ "1: .space 4\n"
+ " .globl shmobile_boot_size\n"
+ "shmobile_boot_size:\n"
+ " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Really don't know whether it can be implemented in C.
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
Quoted 2 lines
I was thinking of moving this code to a separate ASM file in order not to mix C and ASM. What do you think about it?
U-Boot already has a reset vector code, can't that be reused ?
I don't think. Being honest, I couldn't find an obvious way how to reuse (I assume you meant
arch/arm/cpu/armv7/start.S).Maybe it needs some additional work first ?
It seems Altera socfpga somehow uses the U-Boot reset vectors for PSCI, so it should at least be possible.
Could you, please, point me in code? Unfortunately, I wasn't able to find.
Quoted 8 lines
Quoted 6 lines
The newly turned on secondary CPU entry should be common "
psci_cpu_entry", which does proper things.And this reset vector is just "a small piece of code" to be located in on-chip RAM (with limited size) and used for the jump stub...
We already have the SPL reset vectors in SRAM, maybe that can be recycled somehow ?
The only idea I have, how it may be recycled (not sure whether it will work...)
arch/arm/cpu/armv7/start.S +8 -0
@@ -36,6 +36,12 @@ #endif reset: + +#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) + b psci_cpu_entry_jump + /* return only if this is not "a newly turned on CPU" using PSCI) */ +#endif + /* Allow the board to save important registers */ b save_boot_params save_boot_params_ret:
@@ -128,6 +134,21 @@ ENDPROC(switch_to_hypervisor) .weak switch_to_hypervisor #endif +/* + * Each platform which implements psci_cpu_entry_jump function should
perform
+ * in the following way:
+ *
+ * If the executing this call CPU is exactly that CPU we are expecting to be
+ * powered on, then jump to psci_cpu_entry and never return.
+ * Otherwise return to the caller.
+ */
+#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) +ENTRY(psci_cpu_entry_jump)
+ movs pc, lr
+ENDPROC(psci_cpu_entry_jump)
+.weak psci_cpu_entry_jump
+#endif
+
/************************************************************************* *
* cpu_init_cp15
What do you think?
It would be much appreciated, if you could provide some hints.
Quoted 114 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 5 lines
Review
Quoted 4 lines
(quoted diff) +3
-0+extern void shmobile_boot_vector(void); +extern unsigned long shmobile_boot_fn; +extern unsigned long shmobile_boot_size;Are the externs necessary ?
Yes, otherwise, compiler will complain.
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
I can hide them in a header file. Shall I do that with moving ASM code to a separate file?
Only if you cannot reuse the U-Boot reset vector ones , which I think you can ?
I tried to explain above, why I can't reuse. So, if you and other reviewers OK with it,
I will move it to a separate file in V2.
I don't quite see why it's a problem to use the U-Boot reset vectors. Sure, it might be needed to adjust that code first if it cannot be used as-is.
Quoted 85 lines
Quoted 74 lines
Quoted 74 lines
Quoted 6 lines
Quoted 6 lines
(quoted diff) +6
-0+void r8a7790_prepare_cpus(unsigned long addr, u32 nr_cpus) +{ + int cpu = get_current_cpu(); + int i, ret = 0; + u32 bar; +Quoted 8 lines
Quoted 7 lines
+
shmobile_boot_fn= addr;
+dsb();
+
+ /* Install reset vector */
+memcpy_toio((void __iomem *)ICRAM1, shmobile_boot_vector, + shmobile_boot_size);
+dmb();Does this take into consideration caches ?
Good question... Probably, I should have added
flush_dcache_range()after copy.Quoted 20 lines
Quoted 20 lines
+ /* Setup reset vectors */
+ bar = (ICRAM1 >> 8) &0xfffffc00;
+writel(bar, RST_BASE + CA15BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA15BAR); +writel(bar, RST_BASE + CA7BAR);
+writel(bar | SBAR_BAREN, RST_BASE + CA7BAR); +dsb();(quoted diff) +7
-0+ + /* Perform setup for debug mode for all CPUs */ + for (i = 0; i < nr_cpus; i++) + apmu_setup_debug_mode(i); + + /* + * Indicate the completion status of power shutoff/resumeprocedure
+ * for CA15/CA7 SCU.
+ */
+writel(BIT(CA15_SCU_ISR_BIT) | BIT(CA7_SCU_ISR_BIT), + SYSC_BASE + SYSCIER);
+Quoted 8 lines
Quoted 7 lines
+ /* Power on CA15/CA7 SCU */
+ if (sysc_power_is_off(CA15_SCU))
+ ret +=sysc_power_up(CA15_SCU);
+ if (sysc_power_is_off(CA7_SCU))
+ ret +=sysc_power_up(CA7_SCU);
+ if (ret)
+printf("warning: some of secondary CPUs may not boot\n");"some" is not very useful for debugging,.
OK, will provide more concrete output.
Quoted 14 lines
Quoted 14 lines
+ /* Keep secondary CPUs in reset */
+ for (i = 0; i <nr_cpus; i++) {
+ /* Make sure that we don't reset boot CPU */ + if (i == cpu)
+ continue;(quoted diff) +6
-0+ + r8a7790_assert_reset(i); + } + + /* + * Enable snoop requests and DVM message requests for slaveinterfaces
+ * S4 (CA7) and S3 (CA15).
+ */Quoted 8 lines
Quoted 7 lines
+ writel(readl(CCI_BASE +
CCI_SLAVE3+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE3+CCI_SNOOP);
+ writel(readl(CCI_BASE +CCI_SLAVE4+CCI_SNOOP) |CCI_ENABLE_REQ, +CCI_BASE+CCI_SLAVE4+CCI_SNOOP);
+ /* Wait for pending bit low */
+ while (readl(CCI_BASE + CCI_STATUS))
+ ;can this spin forever ?
Paragraph "3.3.4 Status Register" in "ARM CoreLink™CCI-400 Cache Coherent Interconnect" document says nothing
about possibility to spin forever. Just next:
Quoted 7 lines
Quoted 4 lines
"After writing to the snoop or DVM enable bits, the controller must wait for the register write to
complete, then test that thechange_pendingbit is LOW before it turns an attached device on or off."So what if this code spins forever, will this also completely hang Linux which calls this code ?
[...]In this case, no. This is PSCI board initialization code, which is being executed while we are still in U-Boot.
Quoted 8 lines
Unlike r8a7790_apmu_power_on()/r8a7790_apmu_power_off() functions, which are indented to be called from PSCI handlers (at runtime), when the "main" U-Boot is gone away.
If this code spins forever, U-Boot will get stuck before even starting Linux/Hypervisor.
Probably, it would be better to add safe timeout (~1s) here as well.
I think so.
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
Hi, Marek
Quoted 102 lines
Quoted 35 lines
Quoted 35 lines
Quoted 35 lines
Quoted 35 lines
Quoted 15 lines
Quoted 15 lines
(quoted diff) +15
-0+} + +/* + * Reset vector for secondary CPUs. + * This will be mapped at address 0 by SBAR register. + * We need _long_ jump to the physical address. + */ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n" + " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"Quoted 8 lines
Quoted 7 lines
+ " .align 2\n"
+ " .globl shmobile_boot_fn\n"
+ "shmobile_boot_fn:\n"
+ "1: .space 4\n"
+ " .globl shmobile_boot_size\n"
+ "shmobile_boot_size:\n"
+ " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not
to mix C and ASM. What do you think about it?Quoted 7 lines
Quoted 4 lines
Quoted 1 line
U-Boot already has a reset vector code, can't that be reused ?
I don't think. Being honest, I couldn't find an obvious way how to reuse
(I assume you meantarch/arm/cpu/armv7/start.S).Maybe it needs some additional work first ?
It seems Altera socfpga somehow uses the U-Boot reset vectors for PSCI, so it should at least be possible.Could you, please, point me in code? Unfortunately, I wasn't able to find.
Quoted 8 lines
Quoted 6 lines
The newly turned on secondary CPU entry should be common "
psci_cpu_entry", which does proper things.And this reset vector is just "a small piece of code" to be located in on-chip RAM (with limited size) and used for the jump stub...
We already have the SPL reset vectors in SRAM, maybe that can be recycled somehow ?
The only idea I have, how it may be recycled (not sure whether it will work...)
arch/arm/cpu/armv7/start.S +0
-0@@ -36,6 +36,12 @@ #endifreset:
arch/arm/cpu/armv7/start.S +4
-0+ +#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) + b psci_cpu_entry_jump + /* return only if this is not "a newly turned on CPU" usingPSCI) */
arch/arm/cpu/armv7/start.S +2
-0+#endif +/* Allow the board to save important registers */ b
save_boot_paramssave_boot_params_ret:arch/arm/cpu/armv7/start.S +0
-0@@ -128,6 +134,21 @@ ENDPROC(switch_to_hypervisor).weak
switch_to_hypervisor
#endif+/*
+ * Each platform which implementspsci_cpu_entry_jumpfunction should perform
+ * in the following way:
+ *
+ * If the executing this call CPU is exactly that CPU we are expecting to be
+ * powered on, then jump topsci_cpu_entryand never return.
+ * Otherwise return to the caller.
+ */arch/arm/cpu/armv7/start.S +7
-0+#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) +ENTRY(psci_cpu_entry_jump) + movs pc, lr +ENDPROC(psci_cpu_entry_jump) +.weak psci_cpu_entry_jump +#endif +/*************************************************************************
Quoted 8 lines
*
*cpu_init_cp15What do you think?
It would be much appreciated, if you could provide some hints.
Don't want to be annoying, but it would be really nice to get my questions answered...
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
Quoted 2 lines · Oleksandr
Hi, Marek
Hi,
Quoted 106 lines
Quoted 106 lines
Quoted 35 lines
Quoted 35 lines
Quoted 35 lines
Quoted 35 lines
Quoted 15 lines
Quoted 15 lines
(quoted diff) +15
-0+} + +/* + * Reset vector for secondary CPUs. + * This will be mapped at address 0 by SBAR register. + * We need _long_ jump to the physical address. + */ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n" + " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n"Quoted 8 lines
Quoted 7 lines
+ " .align 2\n"
+ " .globl shmobile_boot_fn\n"
+ "shmobile_boot_fn:\n"
+ "1: .space 4\n"
+ " .globl shmobile_boot_size\n"
+ "shmobile_boot_size:\n"
+ " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
This "reset vector" code was ported from Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not
to mix C and ASM. What do you think about it?Quoted 7 lines
Quoted 4 lines
Quoted 1 line
U-Boot already has a reset vector code, can't that be reused ?
I don't think. Being honest, I couldn't find an obvious way how to reuse
(I assume you meantarch/arm/cpu/armv7/start.S).Maybe it needs some additional work first ?
It seems Altera socfpga somehow uses the U-Boot reset vectors for PSCI, so it should at least be possible.Could you, please, point me in code? Unfortunately, I wasn't able to find.
Quoted 8 lines
Quoted 6 lines
The newly turned on secondary CPU entry should be common "
psci_cpu_entry", which does proper things.And this reset vector is just "a small piece of code" to be located in on-chip RAM (with limited size) and used for the jump stub...
We already have the SPL reset vectors in SRAM, maybe that can be recycled somehow ?
The only idea I have, how it may be recycled (not sure whether it will work...)
arch/arm/cpu/armv7/start.S +0
-0@@ -36,6 +36,12 @@ #endifreset:
arch/arm/cpu/armv7/start.S +4
-0+ +#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) + b psci_cpu_entry_jump + /* return only if this is not "a newly turned on CPU" usingPSCI) */
arch/arm/cpu/armv7/start.S +2
-0+#endif +/* Allow the board to save important registers */ b
save_boot_paramssave_boot_params_ret:arch/arm/cpu/armv7/start.S +0
-0@@ -128,6 +134,21 @@ ENDPROC(switch_to_hypervisor).weak
switch_to_hypervisor
#endif+/*
+ * Each platform which implementspsci_cpu_entry_jumpfunction should perform
+ * in the following way:
+ *
+ * If the executing this call CPU is exactly that CPU we are expecting to be
+ * powered on, then jump topsci_cpu_entryand never return.
+ * Otherwise return to the caller.
+ */arch/arm/cpu/armv7/start.S +7
-0+#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) +ENTRY(psci_cpu_entry_jump) + movs pc, lr +ENDPROC(psci_cpu_entry_jump) +.weak psci_cpu_entry_jump +#endif +/*************************************************************************
*
*cpu_init_cp15
Quoted 8 lines
Quoted 4 lines
What do you think?
It would be much appreciated, if you could provide some hints.
Don't want to be annoying, but it would be really nice to get my questions answered...
I am sorry, I am too busy right now. I will answer that once I can properly study the problem and give you a useful answer.
Signature · 2 lines
Best regards, Marek Vasut
PATCH 2/3 ARM: rmobile: Add basic PSCI support for r8a7790 SoC
Hi, Marek
sorry for possible format issue.
ср, 27 февр. 2019 г., 23:02 Marek Vasut <[email protected]>:
Quoted 117 lines · Oleksandr
Quoted 2 lines
Hi, Marek
Hi,
Quoted 23 lines
Quoted 23 lines
Quoted 23 lines
Quoted 23 lines
Quoted 23 lines
Quoted 23 lines
Quoted 23 lines
Quoted 12 lines
(quoted diff) +12
-0+} + +/* + * Reset vector for secondary CPUs. + * This will be mapped at address 0 by SBAR register. + * We need _long_ jump to the physical address. + */ +asm(" .arm\n" + " .align 12\n" + " .globl shmobile_boot_vector\n" + "shmobile_boot_vector:\n" + " ldr r1, 1f\n"Review
Quoted 10 lines
(quoted diff) +10
-0+ " bx r1\n" + " .type shmobile_boot_vector, %function\n" + " .size shmobile_boot_vector, .-shmobile_boot_vector\n" + " .align 2\n" + " .globl shmobile_boot_fn\n" + "shmobile_boot_fn:\n" + "1: .space 4\n" + " .globl shmobile_boot_size\n" + "shmobile_boot_size:\n" + " .long .-shmobile_boot_vector\n");Why can't this be implemented in C ?
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
This "reset vector" code was ported from Linux:
https://elixir.bootlin.com/linux/v5.0-rc5/source/arch/arm/mach-shmobile/headsmp.S#L21
Quoted 67 lines
Quoted 67 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Really don't know whether it can be implemented in C.
I was thinking of moving this code to a separate ASM file in order not
to mix C and ASM. What do you think about it?Quoted 7 lines
Quoted 4 lines
Quoted 1 line
U-Boot already has a reset vector code, can't that be reused ?
I don't think. Being honest, I couldn't find an obvious way how to reuse
(I assume you meantarch/arm/cpu/armv7/start.S).Maybe it needs some additional work first ?
It seems Altera socfpga somehow uses the U-Boot reset vectors for PSCI, so it should at least be possible.Could you, please, point me in code? Unfortunately, I wasn't able to find.
Quoted 8 lines
Quoted 6 lines
The newly turned on secondary CPU entry should be common "
psci_cpu_entry", which does proper things.And this reset vector is just "a small piece of code" to be located in on-chip RAM (with limited size) and used for the jump stub...
We already have the SPL reset vectors in SRAM, maybe that can be recycled somehow ?
The only idea I have, how it may be recycled (not sure whether it will work...)
arch/arm/cpu/armv7/start.S +4
-0@@ -36,6 +36,12 @@ #endif reset: + +#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) + b psci_cpu_entry_jump + /* return only if this is not "a newly turned on CPU" usingPSCI) */
arch/arm/cpu/armv7/start.S +4
-0+#endif + /* Allow the board to save important registers */ b save_boot_params save_boot_params_ret:@@ -128,6 +134,21 @@ ENDPROC(switch_to_hypervisor) .weak switch_to_hypervisor #endif +/* + * Each platform which implements psci_cpu_entry_jump function shouldperform
+ * in the following way:
+ *
+ * If the executing this call CPU is exactly that CPU we are expecting to be
+ * powered on, then jump topsci_cpu_entryand never return.
+ * Otherwise return to the caller.
+ */Quoted 8 lines
arch/arm/cpu/armv7/start.S
Quoted 8 lines
arch/arm/cpu/armv7/start.S +7
-0+#if defined(CONFIG_ARMV7_PSCI) && !defined(CONFIG_SPL_BUILD) +ENTRY(psci_cpu_entry_jump) + movs pc, lr +ENDPROC(psci_cpu_entry_jump) +.weak psci_cpu_entry_jump +#endif +/*************************************************************************
Quoted 8 lines
Quoted 8 lines
*
*cpu_init_cp15What do you think?
Quoted 9 lines
Quoted 5 lines
Quoted 1 line
It would be much appreciated, if you could provide some hints.
Don't want to be annoying, but it would be really nice to get my questions answered...
I am sorry, I am too busy right now. I will answer that once I can properly study the problem and give you a useful answer.
No problem, I will wait.
Thank you.
Quoted 4 lines
--
Best regards,
Marek Vasut
PATCH 3/3 ARM: rmobile: Add possibility to debug main PSCI commands
In reply to Oleksandr TyshchenkoFrom: Oleksandr Tyshchenko <[email protected]>
Also take care of the fact that Lager and Stout boards use different serial interface for console.
--- arch/arm/mach-rmobile/debug.h | 91 +++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/psci.c | 23 +++++++++++ 2 files changed, 114 insertions(+) create mode 100644 arch/arm/mach-rmobile/debug.h
arch/arm/mach-rmobile/debug.h new file +91 -0
@@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Contains functions used for PSCI debug. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Based on arch/arm/mach-uniphier/debug.h +*/ + +#ifndef __DEBUG_H__ +#define __DEBUG_H__ + +#include <asm/io.h> + +/* SCIFA definitions */ +#define SCIFA_BASE 0xe6c40000 + +#define SCIFA_SCASSR 0x14/* Serial status register */ +#define SCIFA_SCAFTDR 0x20/* Transmit FIFO data register */ + +/* SCIF definitions */ +#define SCIF_BASE 0xe6e60000 + +#define SCIF_SCFSR 0x10/* Serial status register */ +#define SCIF_SCFTDR 0x0c/* Transmit FIFO data register */ + +/* Common for both interfaces definitions */ +#define SCFSR_TDFE BIT(5)/* Transmit FIFO Data Empty */ +#define SCFSR_TEND BIT(6)/* Transmission End */ + +#ifdef CONFIG_SCIF_A +#define UART_BASE SCIFA_BASE +#define UART_STATUS_REG SCIFA_SCASSR +#define UART_TX_FIFO_REG SCIFA_SCAFTDR +#else +#define UART_BASE SCIF_BASE +#define UART_STATUS_REG SCIF_SCFSR +#define UART_TX_FIFO_REG SCIF_SCFTDR +#endif + +/* All functions are inline so that they can be called from .secure section. */ + +#ifdef DEBUG +static inline void debug_putc (int c) +{ +void __iomem *base = (void __iomem *)UART_BASE ; + +while (!(readw (base +UART_STATUS_REG ) &SCFSR_TDFE )) + ; + +writeb (c, base +UART_TX_FIFO_REG ); +writew (readw (base +UART_STATUS_REG ) & ~(SCFSR_TEND |SCFSR_TDFE ), + base +UART_STATUS_REG ); +} + +static inline void debug_puts (const char *s) +{ +while (*s) { +if (*s =='\n' ) +debug_putc ('\r' ); + +debug_putc (*s++); + } +} + +static inline void debug_puth (unsigned long val) +{ +int i; +unsigned char c; + +for (i =8 ; i--; ) { + c = ((val >> (i *4 )) &0xf ); + c += (c >=10 ) ?'a' -10 :'0' ; +debug_putc (c); + } +} +#else +static inline void debug_putc (int c) +{ +} + +static inline void debug_puts (const char *s) +{ +} + +static inline void debug_puth (unsigned long val) +{ +} +#endif + +#endif /* __DEBUG_H__ */
arch/arm/mach-rmobile/psci.c +23 -0
@@ -14,6 +14,7 @@#include <asm/secure.h> #include "pm-r8a7790.h" +#include "debug.h" #define R8A7790_PSCI_NR_CPUS 8#if R8A7790_PSCI_NR_CPUS >CONFIG_ARMV7_PSCI_NR_CPUS
@@ -105,6 +106,16 @@ int __secure psci_cpu_on(u32 function_id, u32 target_cpu, u32 entry_point, {int cpu; +debug_puts ("[U-Boot PSCI] cpu_on: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts (", target_cpu=" ); +debug_puth (target_cpu); +debug_puts (", entry_point=" ); +debug_puth (entry_point); +debug_puts (", context_id=" ); +debug_puth (context_id); +debug_puts ("\n" ); + cpu =mpidr_to_cpu_index (target_cpu);if (cpu ==-1 )return ARM_PSCI_RET_INVAL ;
@@ -130,6 +141,10 @@ int __secure psci_cpu_off(void) {int cpu =get_current_cpu (); +debug_puts ("[U-Boot PSCI] cpu_off: cpu=" ); +debug_puth (cpu); +debug_puts ("\n" ); +/* * Place the CPU interface in a state where it can never make a CPU * exit WFI as result of an asserted interrupt.
@@ -154,6 +169,10 @@ int __secure psci_cpu_off(void) void __secure psci_system_reset(u32 function_id) { +debug_puts ("[U-Boot PSCI] system_reset: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts ("\n" ); +r8a7790_system_reset ();/* Drain the WB before WFI */
@@ -166,6 +185,10 @@ void __secure psci_system_reset(u32 function_id) void __secure psci_system_off(u32 function_id) { +debug_puts ("[U-Boot PSCI] system_off: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts ("\n" ); +/* Drain the WB before WFI */ dsb ();
Signature · 1 line
2.7.4
PATCH 3/3 ARM: rmobile: Add possibility to debug main PSCI commands
Quoted 4 lines · Oleksandr Tyshchenko
From: Oleksandr Tyshchenko <[email protected]>
Also take care of the fact that Lager and Stout boards use different serial interface for console.
This describes something else than $subject , please split the patchset such that one patch does one thing and describes that one thing in the commit message.
Quoted 19 lines
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/debug.h | 91 +++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/psci.c | 23 +++++++++++ 2 files changed, 114 insertions(+) create mode 100644 arch/arm/mach-rmobile/debug.harch/arm/mach-rmobile/debug.h new file +6
-0@@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Contains functions used for PSCI debug. +* +* Copyright (C) 2018 EPAM Systems Inc. +*
arch/arm/mach-rmobile/debug.h line 16
Quoted 10 lines
arch/arm/mach-rmobile/debug.h new file +10
-0+* Based on arch/arm/mach-uniphier/debug.h +*/ + +#ifndef __DEBUG_H__ +#define __DEBUG_H__ + +#include <asm/io.h> + +/* SCIFA definitions */ +#define SCIFA_BASE 0xe6c40000
Should come from DT
Quoted 26 lines
arch/arm/mach-rmobile/debug.h new file +26
-0+#define SCIFA_SCASSR 0x14/* Serial status register */ +#define SCIFA_SCAFTDR 0x20/* Transmit FIFO data register */ + +/* SCIF definitions */ +#define SCIF_BASE 0xe6e60000 + +#define SCIF_SCFSR 0x10/* Serial status register */ +#define SCIF_SCFTDR 0x0c/* Transmit FIFO data register */ + +/* Common for both interfaces definitions */ +#define SCFSR_TDFE BIT(5)/* Transmit FIFO Data Empty */ +#define SCFSR_TEND BIT(6)/* Transmission End */ + +#ifdef CONFIG_SCIF_A +#define UART_BASE SCIFA_BASE +#define UART_STATUS_REG SCIFA_SCASSR +#define UART_TX_FIFO_REG SCIFA_SCAFTDR +#else +#define UART_BASE SCIF_BASE +#define UART_STATUS_REG SCIF_SCFSR +#define UART_TX_FIFO_REG SCIF_SCFTDR +#endif + +/* All functions are inline so that they can be called from .secure section. */ + +#ifdef DEBUG
arch/arm/mach-rmobile/debug.h line 53
Quoted 10 lines
arch/arm/mach-rmobile/debug.h new file +10
-0+static inline void debug_putc (int c) +{ +void __iomem *base = (void __iomem *)UART_BASE ; + +while (!(readw (base +UART_STATUS_REG ) &SCFSR_TDFE )) + ; + +writeb (c, base +UART_TX_FIFO_REG ); +writew (readw (base +UART_STATUS_REG ) & ~(SCFSR_TEND |SCFSR_TDFE ), + base +UART_STATUS_REG );
Is this some implementation of debug uart API or is this a reimplementation of the serial driver ?
Quoted 101 lines
arch/arm/mach-rmobile/debug.h new file +38
-0+} + +static inline void debug_puts (const char *s) +{ +while (*s) { +if (*s =='\n' ) +debug_putc ('\r' ); + +debug_putc (*s++); + } +} + +static inline void debug_puth (unsigned long val) +{ +int i; +unsigned char c; + +for (i =8 ; i--; ) { + c = ((val >> (i *4 )) &0xf ); + c += (c >=10 ) ?'a' -10 :'0' ; +debug_putc (c); + } +} +#else +static inline void debug_putc (int c) +{ +} + +static inline void debug_puts (const char *s) +{ +} + +static inline void debug_puth (unsigned long val) +{ +} +#endif + +#endif /* __DEBUG_H__ */ arch/arm/mach-rmobile/psci.c +23
-0@@ -14,6 +14,7 @@#include <asm/secure.h> #include "pm-r8a7790.h" +#include "debug.h" #define R8A7790_PSCI_NR_CPUS 8#if R8A7790_PSCI_NR_CPUS >CONFIG_ARMV7_PSCI_NR_CPUS @@ -105,6 +106,16 @@ int __secure psci_cpu_on(u32 function_id, u32 target_cpu, u32 entry_point, {int cpu; +debug_puts ("[U-Boot PSCI] cpu_on: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts (", target_cpu=" ); +debug_puth (target_cpu); +debug_puts (", entry_point=" ); +debug_puth (entry_point); +debug_puts (", context_id=" ); +debug_puth (context_id); +debug_puts ("\n" ); + cpu =mpidr_to_cpu_index (target_cpu);if (cpu ==-1 )return ARM_PSCI_RET_INVAL ;@@ -130,6 +141,10 @@ int __secure psci_cpu_off(void) {int cpu =get_current_cpu (); +debug_puts ("[U-Boot PSCI] cpu_off: cpu=" ); +debug_puth (cpu); +debug_puts ("\n" ); +/* * Place the CPU interface in a state where it can never make a CPU * exit WFI as result of an asserted interrupt. @@ -154,6 +169,10 @@ int __secure psci_cpu_off(void) void __secure psci_system_reset(u32 function_id) { +debug_puts ("[U-Boot PSCI] system_reset: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts ("\n" ); +r8a7790_system_reset ();/* Drain the WB before WFI */ @@ -166,6 +185,10 @@ void __secure psci_system_reset(u32 function_id) void __secure psci_system_off(u32 function_id) { +debug_puts ("[U-Boot PSCI] system_off: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts ("\n" ); +/* Drain the WB before WFI */ dsb ();
Signature · 2 lines
Best regards, Marek Vasut
PATCH 3/3 ARM: rmobile: Add possibility to debug main PSCI commands
On 05.02.19 20:56, Marek Vasut wrote:
Hi Marek
Quoted 8 lines · Oleksandr Tyshchenko
Quoted 4 lines
From: Oleksandr Tyshchenko <[email protected]>
Also take care of the fact that Lager and Stout boards use different serial interface for console.
This describes something else than $subject , please split the patchset such that one patch does one thing and describes that one thing in the commit message.
Yes, make sense. Will split.
Quoted 22 lines
Quoted 22 lines
Signed-off-by Oleksandr Tyshchenko <[email protected]>--- arch/arm/mach-rmobile/debug.h | 91 +++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-rmobile/psci.c | 23 +++++++++++ 2 files changed, 114 insertions(+)create mode 100644
arch/arm/mach-rmobile/debug.harch/arm/mach-rmobile/debug.h new file +9
-0@@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Contains functions used for PSCI debug. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Based on arch/arm/mach-uniphier/debug.h +*/ +
Quoted 8 lines
arch/arm/mach-rmobile/debug.h line 16
Quoted 7 lines
arch/arm/mach-rmobile/debug.h new file +7
-0+#ifndef __DEBUG_H__ +#define __DEBUG_H__ + +#include <asm/io.h> + +/* SCIFA definitions */ +#define SCIFA_BASE 0xe6c40000Should come from DT
I have just found that rcar-base.h already contains #define-s for all SCIF(A)s.
Quoted 31 lines
Quoted 31 lines
arch/arm/mach-rmobile/debug.h new file +30
-0+#define SCIFA_SCASSR 0x14/* Serial status register */ +#define SCIFA_SCAFTDR 0x20/* Transmit FIFO data register */ + +/* SCIF definitions */ +#define SCIF_BASE 0xe6e60000 + +#define SCIF_SCFSR 0x10/* Serial status register */ +#define SCIF_SCFTDR 0x0c/* Transmit FIFO data register */ + +/* Common for both interfaces definitions */ +#define SCFSR_TDFE BIT(5)/* Transmit FIFO Data Empty */ +#define SCFSR_TEND BIT(6)/* Transmission End */ + +#ifdef CONFIG_SCIF_A +#define UART_BASE SCIFA_BASE +#define UART_STATUS_REG SCIFA_SCASSR +#define UART_TX_FIFO_REG SCIFA_SCAFTDR +#else +#define UART_BASE SCIF_BASE +#define UART_STATUS_REG SCIF_SCFSR +#define UART_TX_FIFO_REG SCIF_SCFTDR +#endif + +/* All functions are inline so that they can be called from .secure section. */ + +#ifdef DEBUG +static inline void debug_putc (int c) +{ +void __iomem *base = (void __iomem *)UART_BASE ; +
Quoted 8 lines
arch/arm/mach-rmobile/debug.h line 53
Quoted 6 lines
arch/arm/mach-rmobile/debug.h new file +6
-0+while (!(readw (base +UART_STATUS_REG ) &SCFSR_TDFE )) + ; + +writeb (c, base +UART_TX_FIFO_REG ); +writew (readw (base +UART_STATUS_REG ) & ~(SCFSR_TEND |SCFSR_TDFE ), + base +UART_STATUS_REG );Is this some implementation of debug uart API or is this a reimplementation of the serial driver ?
I would say it is some implementation of debug uart API.
Let me explain why it is needed. We need something very simple to be called from the PSCI backend
in order to have possibility for debugging it. Actually the only thing we need is a simple function to write a char into uart TX register.
Actually I borrowed that idea from the implementation for mach-uniphier and modified according to the SCIF(A) usage.
These are examples, how it looks like:
1.
[ 3.193974] psci_checker: Trying to turn off and on again group 1 (CPUs 4-7)
[U-Boot PSCI] cpu_off: cpu=00000004
[ 3.233648] Retrying again to check for CPU kill
[ 3.238269] CPU4 killed.
[U-Boot PSCI] cpu_off: cpu=00000005
[ 3.263678] Retrying again to check for CPU kill
[ 3.268298] CPU5 killed.
[U-Boot PSCI] cpu_off: cpu=00000006
[ 3.293648] Retrying again to check for CPU kill
[ 3.298268] CPU6 killed.
[U-Boot PSCI] cpu_off: cpu=00000007
[ 3.323691] Retrying again to check for CPU kill
[ 3.328310] CPU7 killed.
[U-Boot PSCI] cpu_on: cpu=00000001, target_cpu=00000100, entry_point=48102440, context_id=00000000
[U-Boot PSCI] cpu_on: cpu=00000002, target_cpu=00000101, entry_point=48102440, context_id=00000000
[U-Boot PSCI] cpu_on: cpu=00000001, target_cpu=00000102, entry_point=48102440, context_id=00000000
[U-Boot PSCI] cpu_on: cpu=00000001, target_cpu=00000103, entry_point=48102440, context_id=00000000
2.
(XEN) Bringing up CPU4
[U-Boot PSCI] cpu_on: cpu=00000000, target_cpu=00000100, entry_point=4800004c, context_id=0030e208
- CPU 00000100 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 4 to runqueue 0
(XEN) CPU 4 booted.
(XEN) Bringing up CPU5
[U-Boot PSCI] cpu_on: cpu=00000000, target_cpu=00000101, entry_point=4800004c, context_id=0030e208
- CPU 00000101 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 5 to runqueue 0
(XEN) CPU 5 booted.
(XEN) Bringing up CPU6
[U-Boot PSCI] cpu_on: cpu=00000000, target_cpu=00000102, entry_point=4800004c, context_id=0030e208
- CPU 00000102 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 6 to runqueue 0
(XEN) CPU 6 booted.
(XEN) Bringing up CPU7
[U-Boot PSCI] cpu_on: cpu=00000000, target_cpu=00000103, entry_point=4800004c, context_id=0030e208
- CPU 00000103 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 7 to runqueue 0
(XEN) Brought up 8 CPUs
(XEN) CPU 7 booted.
Quoted 102 lines
Quoted 101 lines
arch/arm/mach-rmobile/debug.h new file +38
-0+} + +static inline void debug_puts (const char *s) +{ +while (*s) { +if (*s =='\n' ) +debug_putc ('\r' ); + +debug_putc (*s++); + } +} + +static inline void debug_puth (unsigned long val) +{ +int i; +unsigned char c; + +for (i =8 ; i--; ) { + c = ((val >> (i *4 )) &0xf ); + c += (c >=10 ) ?'a' -10 :'0' ; +debug_putc (c); + } +} +#else +static inline void debug_putc (int c) +{ +} + +static inline void debug_puts (const char *s) +{ +} + +static inline void debug_puth (unsigned long val) +{ +} +#endif + +#endif /* __DEBUG_H__ */ arch/arm/mach-rmobile/psci.c +23
-0@@ -14,6 +14,7 @@#include <asm/secure.h> #include "pm-r8a7790.h" +#include "debug.h" #define R8A7790_PSCI_NR_CPUS 8#if R8A7790_PSCI_NR_CPUS >CONFIG_ARMV7_PSCI_NR_CPUS @@ -105,6 +106,16 @@ int __secure psci_cpu_on(u32 function_id, u32 target_cpu, u32 entry_point, {int cpu; +debug_puts ("[U-Boot PSCI] cpu_on: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts (", target_cpu=" ); +debug_puth (target_cpu); +debug_puts (", entry_point=" ); +debug_puth (entry_point); +debug_puts (", context_id=" ); +debug_puth (context_id); +debug_puts ("\n" ); + cpu =mpidr_to_cpu_index (target_cpu);if (cpu ==-1 )return ARM_PSCI_RET_INVAL ;@@ -130,6 +141,10 @@ int __secure psci_cpu_off(void) {int cpu =get_current_cpu (); +debug_puts ("[U-Boot PSCI] cpu_off: cpu=" ); +debug_puth (cpu); +debug_puts ("\n" ); +/* * Place the CPU interface in a state where it can never make a CPU * exit WFI as result of an asserted interrupt. @@ -154,6 +169,10 @@ int __secure psci_cpu_off(void) void __secure psci_system_reset(u32 function_id) { +debug_puts ("[U-Boot PSCI] system_reset: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts ("\n" ); +r8a7790_system_reset ();/* Drain the WB before WFI */ @@ -166,6 +185,10 @@ void __secure psci_system_reset(u32 function_id) void __secure psci_system_off(u32 function_id) { +debug_puts ("[U-Boot PSCI] system_off: cpu=" ); +debug_puth (get_current_cpu ()); +debug_puts ("\n" ); +/* Drain the WB before WFI */ dsb ();
Signature · 3 lines
Regards, Oleksandr Tyshchenko
PATCH 3/3 ARM: rmobile: Add possibility to debug main PSCI commands
Quoted 4 lines · Oleksandr
On 05.02.19 20:56, Marek Vasut wrote:
Hi Marek
Hi,
Quoted 44 lines
Quoted 8 lines · Oleksandr Tyshchenko
Quoted 4 lines
From: Oleksandr Tyshchenko <[email protected]>
Also take care of the fact that Lager and Stout boards use different serial interface for console.
This describes something else than $subject , please split the patchset such that one patch does one thing and describes that one thing in the commit message.
Yes, make sense. Will split.
Quoted 24 lines
Quoted 24 lines
Signed-off-by Oleksandr Tyshchenko <[email protected]>---
arch/arm/mach-rmobile/debug.h| 91
+++++++++++++++++++++++++++++++++++++++++++
arch/arm/mach-rmobile/psci.c | 23 +++++++++++2 files changed, 114 insertions(+)create mode 100644
arch/arm/mach-rmobile/debug.harch/arm/mach-rmobile/debug.h new file +9
-0@@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Contains functions used for PSCI debug. +* +* Copyright (C) 2018 EPAM Systems Inc. +* +* Based on arch/arm/mach-uniphier/debug.h +*/ +Quoted 8 lines
arch/arm/mach-rmobile/debug.h line 16
Quoted 7 lines
arch/arm/mach-rmobile/debug.h new file +7
-0+#ifndef __DEBUG_H__ +#define __DEBUG_H__ + +#include <asm/io.h> + +/* SCIFA definitions */ +#define SCIFA_BASE 0xe6c40000Should come from DT
Quoted 2 lines
I have just found that
rcar-base.halready contains #define-s for all SCIF(A)s.
So does the DT, and the addresses should come from DT, not from ad-hoc constants in U-Boot. Those will likely be removed at some point.
Quoted 113 lines
Quoted 31 lines
Quoted 31 lines
arch/arm/mach-rmobile/debug.h new file +24
-0+#define SCIFA_SCASSR 0x14/* Serial status register */ +#define SCIFA_SCAFTDR 0x20/* Transmit FIFO data register */ + +/* SCIF definitions */ +#define SCIF_BASE 0xe6e60000 + +#define SCIF_SCFSR 0x10/* Serial status register */ +#define SCIF_SCFTDR 0x0c/* Transmit FIFO data register */ + +/* Common for both interfaces definitions */ +#define SCFSR_TDFE BIT(5)/* Transmit FIFO Data Empty */ +#define SCFSR_TEND BIT(6)/* Transmission End */ + +#ifdef CONFIG_SCIF_A +#define UART_BASE SCIFA_BASE +#define UART_STATUS_REG SCIFA_SCASSR +#define UART_TX_FIFO_REG SCIFA_SCAFTDR +#else +#define UART_BASE SCIF_BASE +#define UART_STATUS_REG SCIF_SCFSR +#define UART_TX_FIFO_REG SCIF_SCFTDR +#endif + +/* All functions are inline so that they can be called from .secure section. */
arch/arm/mach-rmobile/debug.h new file +6
-0+ +#ifdef DEBUG +static inline void debug_putc (int c) +{ + void __iomem *base = (void __iomem *)UART_BASE; +Quoted 8 lines
Quoted 6 lines
+ while (!(readw(base +
UART_STATUS_REG) &SCFSR_TDFE))
+ ;
+
+writeb(c, base + UART_TX_FIFO_REG);
+ writew(readw(base +UART_STATUS_REG) & ~(SCFSR_TEND |SCFSR_TDFE), + base +UART_STATUS_REG);Is this some implementation of debug uart API or is this a reimplementation of the serial driver ?
I would say it is some implementation of debug uart API.
Let me explain why it is needed. We need something very simple to be called from the PSCI backend
in order to have possibility for debugging it. Actually the only thing we need is a simple function to write a char into uart TX register.
Actually I borrowed that idea from the implementation for mach-uniphier and modified according to the SCIF(A) usage.
These are examples, how it looks like:
1.
[ 3.193974]
psci_checker: Trying to turn off and on again group 1 (CPUs 4-7)
[U-Boot PSCI]cpu_off: cpu=00000004
[ 3.233648] Retrying again to check for CPU kill
[ 3.238269] CPU4 killed.
[U-Boot PSCI]cpu_off: cpu=00000005
[ 3.263678] Retrying again to check for CPU kill
[ 3.268298] CPU5 killed.
[U-Boot PSCI]cpu_off: cpu=00000006
[ 3.293648] Retrying again to check for CPU kill
[ 3.298268] CPU6 killed.
[U-Boot PSCI]cpu_off: cpu=00000007
[ 3.323691] Retrying again to check for CPU kill
[ 3.328310] CPU7 killed.
[U-Boot PSCI]cpu_on: cpu=00000001, target_cpu=00000100, entry_point=48102440, context_id=00000000
[U-Boot PSCI]cpu_on: cpu=00000002, target_cpu=00000101, entry_point=48102440, context_id=00000000
[U-Boot PSCI]cpu_on: cpu=00000001, target_cpu=00000102, entry_point=48102440, context_id=00000000
[U-Boot PSCI]cpu_on: cpu=00000001, target_cpu=00000103, entry_point=48102440, context_id=000000002.
(XEN) Bringing up CPU4
[U-Boot PSCI]cpu_on: cpu=00000000, target_cpu=00000100, entry_point=4800004c, context_id=0030e208
- CPU 00000100 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 4 to runqueue 0
(XEN) CPU 4 booted.
(XEN) Bringing up CPU5
[U-Boot PSCI]cpu_on: cpu=00000000, target_cpu=00000101, entry_point=4800004c, context_id=0030e208
- CPU 00000101 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 5 to runqueue 0
(XEN) CPU 5 booted.
(XEN) Bringing up CPU6
[U-Boot PSCI]cpu_on: cpu=00000000, target_cpu=00000102, entry_point=4800004c, context_id=0030e208
- CPU 00000102 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 6 to runqueue 0
(XEN) CPU 6 booted.
(XEN) Bringing up CPU7
[U-Boot PSCI]cpu_on: cpu=00000000, target_cpu=00000103, entry_point=4800004c, context_id=0030e208
Quoted 8 lines
- CPU 00000103 booting -
- Xen starting in Hyp mode -
- Setting up control registers -
- Turning on paging -
- Ready -
(XEN) Adding cpu 7 to runqueue 0
(XEN) Brought up 8 CPUs
(XEN) CPU 7 booted.
OK, this should then sit in drivers/serial/ .
The UART base address and properties should be selected via DT, not via some ad-hoc constant hard-coded into U-Boot.
[...]
Signature · 2 lines
Best regards, Marek Vasut