Skip to contentSkip to conversation

Add the "mfill" and "mcheck" memory commands.

PATCH New Benoit Monin 2 participants 2 messages Mar 3, 2009 – Mar 5, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Add the "mfill" and "mcheck" memory commands.

The mfill command writes the value of a counter to a memory area. The mcheck command verifies the memory area against the counter value. Those commands are useful for debugging memory/framebuffer controller.

The configuration option is CONFIG_MFILL and this only takes effect if the memory commands are activated globally (CONFIG_CMD_MEM).

Signed-off-by Beno?t Monin <bmonin <at> adeneo.eu>
---
 README           |   17 +++++++-
 common/cmd_mem.c |  127 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 143 insertions(+), 1 deletions(-)
README +16 -1
index 43fb1c0..d0a636e 100644
@@ -627,7 +627,7 @@ The following options need to be configured:
 		CONFIG_CMD_LOADB	  loadb
 		CONFIG_CMD_LOADS	  loads
 		CONFIG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
-					  loop, loopw, mtest
+					  loop, loopw, mtest, mfill, mcheck
 		CONFIG_CMD_MISC		  Misc functions like sleep etc
 		CONFIG_CMD_MMC		* MMC memory mapped support
 		CONFIG_CMD_MII		* MII utility commands
@@ -2678,6 +2678,21 @@ Low Level (hardware related) configuration options:
 		This only takes effect if the memory commands are activated
 		globally (CONFIG_CMD_MEM).
 
+- CONFIG_MFILL
+		Add the "mfill" and "mcheck" memory commands. "mfill" writes
+		a memory area with the value of a counter. "mcheck" checks
+		a memory area against the value of a counter and can be run
+		after mfill.
+
+		(mfill/mcheck)[.b, .w, .l] address count [init]
+		  [.b, .w, .l] : Access size (default to l).
+		  address : Address in hexadecimal.
+		  count : Number of elements to write in hex.
+		  [init] : Initial value of the counter (default to 0).
+
+		This only takes effect if the memory commands are activated
+		globally (CONFIG_CMD_MEM).
+
 - CONFIG_SKIP_LOWLEVEL_INIT
 - CONFIG_SKIP_RELOCATE_UBOOT
 
common/cmd_mem.c +127 -0

139 lines not on this page · raw message

Signature · 2 lines
 Cr?ez votre adresse ?lectronique prenom.nom at laposte.net 
 1 Go d'espace de stockage, anti-spam et anti-virus int?gr?s.
#1 lore raw

PATCH 1/1 Add the "mfill" and "mcheck" memory commands.

Dear Benoit Monin,

Quoted 7 lines · In message <28907262.11403.1236090567026.JavaMail.www@wwinf8303> you wrote:

The mfill command writes the value of a counter to a memory area. The mcheck command verifies the memory area against the counter value. Those commands are useful for debugging memory/framebuffer controller.

The configuration option is CONFIG_MFILL and this only takes effect if the memory commands are activated globally (CONFIG_CMD_MEM).

What exactly is the purpose of this patch? Looks like an extremely simple memory test to me. Don't we have already a rich selection of better ones available yet?

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"I can call spirits from the vasty deep."
"Why so can I, or so can any man; but will they come when you do call
for them?"          - Shakespeare, 1 King Henry IV, Act III, Scene I.