Longhaul support for Via C3 (samuel 2) CPU and Via prosavage PM133 northbridge
Hi,
I try to use cpufreq with a Comwell Lv602 motherboard ( VT8605 [ProSavage PM133]) and a Via C3 (samuel 2) CPU.
I have a 2.6.22.6 kernel with C3 longhaul (CONFIG_X86_LONGHAUL=y) set. Unfortunatly, at boot time, I get the messages:
CPU: Centaur VIA Samuel 2 stepping 03
[...]
longhaul: VIA C3 'Samuel 2' [C5B] CPU detected. Longhaul v1 supported.
longhaul: No ACPI support. Unsupported northbridge
Does it mean that this motherboard is not supported, or I missed something?
Thanks
Sylvain
The output of lspci -vv follows:
00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: e0000000-e7ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 5
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Quoted 1 line
Hi,
Hi
Quoted 5 lines
I try to use cpufreq with a Comwell Lv602 motherboard ( VT8605 [ProSavage PM133]) and a Via C3 (samuel 2) CPU.
I have a 2.6.22.6 kernel with C3 longhaul (CONFIG_X86_LONGHAUL=y) set. Unfortunatly, at boot time, I get the messages:
Quoted 7 lines
CPU: Centaur VIA Samuel 2 stepping 03
[...]
longhaul: VIA C3 'Samuel 2' [C5B] CPU detected. Longhaul v1 supported.
longhaul: No ACPI support. Unsupported northbridgeDoes it mean that this motherboard is not supported, or I missed something?
Northbridge has AGP/PCI arbiter disable bits, but support for this northbridge was never tested. Let me know if You are interested in testing it.
Quoted 3 lines
Thanks
Sylvain
Regards
Rafał
----------------------------------------------------------------------
Wygrasz, czy przegrasz?
Quoted 1 line
Quoted 1 line
Quoted 1 line
Hi,
Sure, I'm interested for testing it! What can I do? Regards
Sylvain
Rafał Bilski a écrit :
Quoted 7 lines
Quoted 6 lines
[...]
longhaul: VIA C3 'Samuel 2' [C5B] CPU detected. Longhaul v1 supported.
longhaul: No ACPI support. Unsupported northbridgeDoes it mean that this motherboard is not supported, or I missed something?
Northbridge has AGP/PCI arbiter disable bits, but support for this northbridge was never tested. Let me know if You are interested in testing it.