New DSA driver for VSC9953 Seville switch
Subsystems (6)
Vladimir Oltean
maintainerv2 cover New DSA driver for VSC9953 Seville switch
From: Vladimir Oltean <[email protected]>
Looking at the Felix and Ocelot drivers, Maxim asked if it would be possible to use them as a base for a new driver for the Seville switch inside NXP T1040. Turns out, it is! The result is that the mscc_felix driver was extended to probe on Seville.
The biggest challenge seems to be getting register read/write API generic enough to cover such wild bitfield variations between hardware generations.
There is a trivial dependency patch on the regmap core which is in Mark Brown's for-next tree:
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git/commit/?h=for-next&id=8baebfc2aca26e3fa67ab28343671b82be42b22c
I didn't know what to do with it, so I just added it here as well, as 01/13, so that net-next builds wouldn't break.
Maxim Kochetkov (4):
soc/mscc: ocelot: add MII registers description
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
net: mscc: ocelot: extend watermark encoding function
net: dsa: felix: introduce support for Seville VSC9953 switch
Vladimir Oltean (9):
regmap: add helper for per-port regfield initialization
net: dsa: felix: set proper link speed in felix_phylink_mac_config
net: mscc: ocelot: convert port registers to regmap
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to
regfields
net: dsa: felix: create a template for the DSA tags on xmit
net: mscc: ocelot: split writes to pause frame enable bit and to
thresholds
net: mscc: ocelot: disable flow control on NPI interface
net: dsa: felix: support half-duplex link modes
net: dsa: felix: move probing to felix_vsc9959.c
.../devicetree/bindings/net/dsa/ocelot.txt | 106 +- drivers/net/dsa/ocelot/Kconfig | 12 +- drivers/net/dsa/ocelot/Makefile | 3 +- drivers/net/dsa/ocelot/felix.c | 269 +--- drivers/net/dsa/ocelot/felix.h | 22 +- drivers/net/dsa/ocelot/felix_vsc9959.c | 313 ++++- drivers/net/dsa/ocelot/seville_vsc9953.c | 1111 +++++++++++++++++ drivers/net/ethernet/mscc/ocelot.c | 86 +- drivers/net/ethernet/mscc/ocelot.h | 9 +- drivers/net/ethernet/mscc/ocelot_board.c | 21 +- drivers/net/ethernet/mscc/ocelot_io.c | 18 +- drivers/net/ethernet/mscc/ocelot_regs.c | 61 +- include/linux/regmap.h | 8 + include/soc/mscc/ocelot.h | 68 +- include/soc/mscc/ocelot_dev.h | 78 -- include/soc/mscc/ocelot_qsys.h | 13 - include/soc/mscc/ocelot_sys.h | 23 - net/dsa/tag_ocelot.c | 21 +- 18 files changed, 1811 insertions(+), 431 deletions(-) create mode 100644 drivers/net/dsa/ocelot/seville_vsc9953.c
Signature · 1 line
2.25.1
Vladimir Oltean
maintainerPATCH v2 1/13 regmap: add helper for per-port regfield initialization
From: Vladimir Oltean <[email protected]>
Similar to the standalone regfields, add an initializer for the users who need to set .id_size and .id_offset in order to use the regmap_fields_update_bits_base API.
--- include/linux/regmap.h | 8 ++++++++ 1 file changed, 8 insertions(+)
include/linux/regmap.h +8 -0
@@ -1134,6 +1134,14 @@ struct reg_field { .msb = _msb, \ } +#define REG_FIELD_ID (_reg, _lsb, _msb, _size, _offset) { \ + .reg = _reg, \ + .lsb = _lsb, \ + .msb = _msb, \ + .id_size = _size, \ + .id_offset = _offset, \ + } +struct regmap_field *regmap_field_alloc (struct regmap *regmap,struct reg_field reg_field);void regmap_field_free (struct regmap_field *field);
Signature · 1 line
2.25.1
Vladimir Oltean
maintainerPATCH v2 2/13 net: dsa: felix: set proper link speed in felix_phylink_mac_config
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
state->speed holds a value of 10, 100, 1000 or 2500, but SYS_MAC_FC_CFG_FC_LINK_SPEE and DEV_CLOCK_CFG_LINK_SPEED expect a value in the range 0, 1, 2 or 3.
Even truncated to 2 bits, we are still writing incorrect values to the registers, but for some reason Felix still works.
On Seville (which we're introducing now), however, we need to set correct values for the link speed into the MAC registers. Do that now.
---
Changes in v2:
Patch is new.
drivers/net/dsa/ocelot/felix.c | 40 +++++++++++++++++++++++++++------- 1 file changed, 32 insertions(+), 8 deletions(-)
drivers/net/dsa/ocelot/felix.c +32 -8
@@ -208,18 +208,39 @@ static void felix_phylink_mac_config(struct dsa_switch *ds, int port,struct ocelot *ocelot = ds->priv;struct ocelot_port *ocelot_port = ocelot->ports[port];struct felix *felix =ocelot_to_felix (ocelot); -u32 mac_fc_cfg; +u32 clock_cfg, mac_fc_cfg; + +switch (state->speed) { +case SPEED_10 : + mac_fc_cfg =SYS_MAC_FC_CFG_FC_LINK_SPEED (3 ); + clock_cfg =DEV_CLOCK_CFG_LINK_SPEED (3 ); +break ; +case SPEED_100 : + mac_fc_cfg =SYS_MAC_FC_CFG_FC_LINK_SPEED (2 ); + clock_cfg =DEV_CLOCK_CFG_LINK_SPEED (2 ); +break ; +case SPEED_1000 : + mac_fc_cfg =SYS_MAC_FC_CFG_FC_LINK_SPEED (1 ); + clock_cfg =DEV_CLOCK_CFG_LINK_SPEED (1 ); +break ; +case SPEED_2500 : + mac_fc_cfg =SYS_MAC_FC_CFG_FC_LINK_SPEED (1 ); + clock_cfg =DEV_CLOCK_CFG_LINK_SPEED (0 ); +break ; +case SPEED_UNKNOWN : + mac_fc_cfg =SYS_MAC_FC_CFG_FC_LINK_SPEED (0 ); + clock_cfg =DEV_CLOCK_CFG_LINK_SPEED (0 ); +break ; +default : +dev_err (ocelot->dev,"Unsupported speed on port %d: %d\n" , + port, state->speed); +return ; + }/* Take port out of reset by clearing the MAC_TX_RST, MAC_RX_RST and * PORT_RST bits in CLOCK_CFG */ -ocelot_port_writel (ocelot_port,DEV_CLOCK_CFG_LINK_SPEED (state->speed), -DEV_CLOCK_CFG ); - -/* Flow control. Link speed is only used here to evaluate the time -* specification in incoming pause frames. -*/ - mac_fc_cfg =SYS_MAC_FC_CFG_FC_LINK_SPEED (state->speed); +ocelot_port_writel (ocelot_port, clock_cfg,DEV_CLOCK_CFG );/* handle Rx pause in all cases, with 2500base-X this is used for rate * adaptation.
@@ -231,6 +252,9 @@ static void felix_phylink_mac_config(struct dsa_switch *ds, int port,SYS_MAC_FC_CFG_PAUSE_VAL_CFG (0xffff ) |SYS_MAC_FC_CFG_FC_LATENCY_CFG (0x7 ) |SYS_MAC_FC_CFG_ZERO_PAUSE_ENA ; +/* Flow control. Link speed is only used here to evaluate the time +* specification in incoming pause frames. +*/ ocelot_write_rix (ocelot, mac_fc_cfg,SYS_MAC_FC_CFG , port);ocelot_write_rix (ocelot,0 ,ANA_POL_FLOWC , port);
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 02/13] net: dsa: felix: set proper link speed in felix_phylink_mac_config
Quoted 6 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
state->speedholds a value of 10, 100, 1000 or 2500, butSYS_MAC_FC_CFG_FC_LINK_SPEEandDEV_CLOCK_CFG_LINK_SPEEDexpect a value in the range 0, 1, 2 or 3.
Quoted 7 lines
Even truncated to 2 bits, we are still writing incorrect values to the registers, but for some reason Felix still works.
On Seville (which we're introducing now), however, we need to set correct values for the link speed into the MAC registers. Do that now.
Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 3/13 net: mscc: ocelot: convert port registers to regmap
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
At the moment, there are some minimal register differences between VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences are more pronounced. The MAC registers are located at different offsets within the DEV_GMII target. So we need to refactor the driver to keep a regmap even for per-port registers. The callers of the ocelot_port_readl and ocelot_port_writel were kept unchanged, only the implementation is now more generic.
---
Changes in v2:
None.
drivers/net/dsa/ocelot/felix.c | 13 ++-- drivers/net/dsa/ocelot/felix_vsc9959.c | 47 +++++++++++++- drivers/net/ethernet/mscc/ocelot.c | 5 +- drivers/net/ethernet/mscc/ocelot.h | 3 +- drivers/net/ethernet/mscc/ocelot_board.c | 8 +-- drivers/net/ethernet/mscc/ocelot_io.c | 16 ++++- drivers/net/ethernet/mscc/ocelot_regs.c | 45 +++++++++++++- include/soc/mscc/ocelot.h | 42 ++++++++++++- include/soc/mscc/ocelot_dev.h | 78 ------------------------ 9 files changed, 158 insertions(+), 99 deletions(-)
drivers/net/dsa/ocelot/felix.c +7 -6
@@ -502,7 +502,7 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)for (port =0 ; port < num_phys_ports; port++) {struct ocelot_port *ocelot_port; -void __iomem *port_regs; +struct regmap *target; ocelot_port = devm_kzalloc(ocelot->dev, sizeof(struct ocelot_port),
@@ -519,17 +519,18 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports) res.start += switch_base; res.end += switch_base; - port_regs =devm_ioremap_resource (ocelot->dev, &res); -if (IS_ERR (port_regs)) { + target =ocelot_regmap_init (ocelot, &res); +if (IS_ERR (target)) {dev_err (ocelot->dev, -"failed to map registers for port %d\n" , port); +"Failed to map memory space for port %d\n" , + port);kfree (port_phy_modes); -return PTR_ERR (port_regs); +return PTR_ERR (target); } ocelot_port->phy_mode = port_phy_modes[port]; ocelot_port->ocelot = ocelot; - ocelot_port->regs = port_regs; + ocelot_port->target = target; ocelot->ports[port] = ocelot_port; }
drivers/net/dsa/ocelot/felix_vsc9959.c +45 -2
62 lines not on this page · raw message
drivers/net/ethernet/mscc/ocelot.c +2 -3
@@ -2109,8 +2109,7 @@ void ocelot_init_port(struct ocelot *ocelot, int port) }EXPORT_SYMBOL (ocelot_init_port); -int ocelot_probe_port (struct ocelot *ocelot,u8 port, -void __iomem *regs, +int ocelot_probe_port (struct ocelot *ocelot,int port,struct regmap *target,struct phy_device *phy) {struct ocelot_port_private *priv;
@@ -2128,7 +2127,7 @@ int ocelot_probe_port(struct ocelot *ocelot, u8 port, priv->chip_port = port; ocelot_port = &priv->port; ocelot_port->ocelot = ocelot; - ocelot_port->regs = regs; + ocelot_port->target = target; ocelot->ports[port] = ocelot_port; dev->netdev_ops = &ocelot_port_netdev_ops;
drivers/net/ethernet/mscc/ocelot.h +1 -2
@@ -67,8 +67,7 @@ void ocelot_port_writel(struct ocelot_port *port, u32 val, u32 reg);#define ocelot_field_read (ocelot, reg, val) regmap_field_read((ocelot)->regfields[(reg)], (val))int ocelot_chip_init (struct ocelot *ocelot,const struct ocelot_ops *ops); -int ocelot_probe_port (struct ocelot *ocelot,u8 port, -void __iomem *regs, +int ocelot_probe_port (struct ocelot *ocelot,int port,struct regmap *target,struct phy_device *phy); void ocelot_set_cpu_port(struct ocelot *ocelot, int cpu,
drivers/net/ethernet/mscc/ocelot_board.c +4 -4
@@ -506,9 +506,9 @@ static int mscc_ocelot_probe(struct platform_device *pdev)struct device_node *phy_node;phy_interface_t phy_mode;struct phy_device *phy; +struct regmap *target;struct resource *res;struct phy *serdes; -void __iomem *regs;char res_name[8 ];u32 port;
@@ -519,8 +519,8 @@ static int mscc_ocelot_probe(struct platform_device *pdev) res =platform_get_resource_byname (pdev,IORESOURCE_MEM , res_name); - regs =devm_ioremap_resource (&pdev->dev, res); -if (IS_ERR (regs)) + target =ocelot_regmap_init (ocelot, res); +if (IS_ERR (target))continue ; phy_node =of_parse_phandle (portnp,"phy-handle" ,0 );
@@ -532,7 +532,7 @@ static int mscc_ocelot_probe(struct platform_device *pdev)if (!phy)continue ; - err =ocelot_probe_port (ocelot, port, regs, phy); + err =ocelot_probe_port (ocelot, port, target, phy);if (err) {of_node_put (portnp); goto out_put_ports;
drivers/net/ethernet/mscc/ocelot_io.c +14 -2
@@ -49,13 +49,25 @@ EXPORT_SYMBOL(__ocelot_rmw_ix);u32 ocelot_port_readl (struct ocelot_port *port,u32 reg) { -return readl (port->regs + reg); +struct ocelot *ocelot = port->ocelot; +u16 target = reg >>TARGET_OFFSET ; +u32 val; + +WARN_ON (!target); + +regmap_read (port->target, ocelot->map[target][reg ®_MASK ], &val); +return val; }EXPORT_SYMBOL (ocelot_port_readl);void ocelot_port_writel (struct ocelot_port *port,u32 val,u32 reg) { -writel (val, port->regs + reg); +struct ocelot *ocelot = port->ocelot; +u16 target = reg >>TARGET_OFFSET ; + +WARN_ON (!target); + +regmap_write (port->target, ocelot->map[target][reg ®_MASK ], val); }EXPORT_SYMBOL (ocelot_port_writel);
drivers/net/ethernet/mscc/ocelot_regs.c +44 -1
57 lines not on this page · raw message
include/soc/mscc/ocelot.h +41 -1
60 lines not on this page · raw message
include/soc/mscc/ocelot_dev.h +0 -78
213 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 03/13] net: mscc: ocelot: convert port registers to regmap
Quoted 6 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
At the moment, there are some minimal register differences between VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are missing from Felix because it was integrated with an NXP PCS.
Quoted 8 lines
But with VSC9953 Seville (not yet introduced), the register differences are more pronounced. The MAC registers are located at different offsets within the
DEV_GMIItarget. So we need to refactor the driver to keep a regmap even for per-port registers. The callers of theocelot_port_readlandocelot_port_writelwere kept unchanged, only the implementation is now more generic.Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 4/13 soc/mscc: ocelot: add MII registers description
In reply to Vladimir OlteanFrom: Maxim Kochetkov <[email protected]>
Add the register definitions for the MSCC MIIM MDIO controller in preparation for seville_vsc9959.c to create its accessors for the internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not instantiated by felix and ocelot, we need to define the size of the regfields arrays explicitly, otherwise ocelot_regfields_init, which iterates up to REGFIELD_MAX, will fault on the undefined regfield entries (if we're lucky).
---
Changes in v2:
Initialize regfields array with correct size.
drivers/net/dsa/ocelot/felix_vsc9959.c | 2 +- drivers/net/ethernet/mscc/ocelot_regs.c | 2 +- include/soc/mscc/ocelot.h | 5 +++++ 3 files changed, 7 insertions(+), 2 deletions(-)
drivers/net/dsa/ocelot/felix_vsc9959.c +1 -1
@@ -469,7 +469,7 @@ static const struct resource vsc9959_imdio_res = { .name = "imdio", }; -static const struct reg_field vsc9959_regfields[] = { +static const struct reg_field vsc9959_regfields[REGFIELD_MAX ] = { [ANA_ADVLEARN_VLAN_CHK ] =REG_FIELD (ANA_ADVLEARN ,6 ,6 ), [ANA_ADVLEARN_LEARN_MIRROR ] =REG_FIELD (ANA_ADVLEARN ,0 ,5 ), [ANA_ANEVENTS_FLOOD_DISCARD ] =REG_FIELD (ANA_ANEVENTS ,30 ,30 ),
drivers/net/ethernet/mscc/ocelot_regs.c +1 -1
@@ -299,7 +299,7 @@ static const u32 *ocelot_regmap[TARGET_MAX] = { [DEV_GMII] = ocelot_dev_gmii_regmap, }; -static const struct reg_field ocelot_regfields[] = { +static const struct reg_field ocelot_regfields[REGFIELD_MAX ] = { [ANA_ADVLEARN_VLAN_CHK ] =REG_FIELD (ANA_ADVLEARN ,11 ,11 ), [ANA_ADVLEARN_LEARN_MIRROR ] =REG_FIELD (ANA_ADVLEARN ,0 ,10 ), [ANA_ANEVENTS_MSTI_DROP ] =REG_FIELD (ANA_ANEVENTS ,27 ,27 ),
include/soc/mscc/ocelot.h +5 -0
@@ -394,6 +394,9 @@ enum ocelot_reg {PTP_CLK_CFG_ADJ_CFG ,PTP_CLK_CFG_ADJ_FREQ ,GCB_SOFT_RST =GCB <<TARGET_OFFSET , +GCB_MIIM_MII_STATUS , +GCB_MIIM_MII_CMD , +GCB_MIIM_MII_DATA ,DEV_CLOCK_CFG =DEV_GMII <<TARGET_OFFSET ,DEV_PORT_MISC , DEV_EVENTS,
@@ -481,6 +484,8 @@ enum ocelot_regfield {SYS_RESET_CFG_MEM_ENA ,SYS_RESET_CFG_MEM_INIT ,GCB_SOFT_RST_SWC_RST , +GCB_MIIM_MII_STATUS_PENDING , +GCB_MIIM_MII_STATUS_BUSY , REGFIELD_MAX };
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 04/13] soc/mscc: ocelot: add MII registers description
Quoted 6 lines · Vladimir Oltean
From: Maxim Kochetkov <[email protected]>
Add the register definitions for the MSCC MIIM MDIO controller in preparation for
seville_vsc9959.cto create its accessors for the internal MDIO bus.
Quoted 8 lines
Since we've introduced elements to
ocelot_regfieldsthat are not instantiated by felix and ocelot, we need to define the size of the regfields arrays explicitly, otherwiseocelot_regfields_init, which iterates up toREGFIELD_MAX, will fault on the undefined regfield entries (if we're lucky).Signed-off-by Maxim Kochetkov <[email protected]>Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 5/13 net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
Currently Felix and Ocelot share the same bit layout in these per-port registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the number of ports, and register size per port, and use the regmap API for multiple ports.
---
Changes in v2:
None.
drivers/net/dsa/ocelot/felix.c | 11 +++---- drivers/net/dsa/ocelot/felix_vsc9959.c | 11 +++++++ drivers/net/ethernet/mscc/ocelot.c | 44 ++++++++++++------------- drivers/net/ethernet/mscc/ocelot.h | 6 ---- drivers/net/ethernet/mscc/ocelot_io.c | 2 ++ drivers/net/ethernet/mscc/ocelot_regs.c | 11 +++++++ include/soc/mscc/ocelot.h | 15 +++++++++ include/soc/mscc/ocelot_qsys.h | 13 -------- include/soc/mscc/ocelot_sys.h | 13 -------- 9 files changed, 66 insertions(+), 60 deletions(-)
drivers/net/dsa/ocelot/felix.c +5 -6
@@ -284,8 +284,7 @@ static void felix_phylink_mac_link_down(struct dsa_switch *ds, int port,struct ocelot_port *ocelot_port = ocelot->ports[port];ocelot_port_writel (ocelot_port,0 ,DEV_MAC_ENA_CFG ); -ocelot_rmw_rix (ocelot,0 ,QSYS_SWITCH_PORT_MODE_PORT_ENA , -QSYS_SWITCH_PORT_MODE , port); +ocelot_fields_write (ocelot, port,QSYS_SWITCH_PORT_MODE_PORT_ENA ,0 ); } static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port,
@@ -311,10 +310,10 @@ static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port, ANA_PORT_PORT_CFG, port);/* Core: Enable port for frame transfer */ -ocelot_write_rix (ocelot,QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE | -QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG (1 ) | -QSYS_SWITCH_PORT_MODE_PORT_ENA , -QSYS_SWITCH_PORT_MODE , port); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE ,1 ); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_PORT_ENA ,1 ); }static void felix_port_qos_map_init (struct ocelot *ocelot,int port)
drivers/net/dsa/ocelot/felix_vsc9959.c +11 -0
@@ -503,6 +503,17 @@ static const struct reg_field vsc9959_regfields[REGFIELD_MAX] = { [ANA_TABLES_MACTINDX_M_INDEX] = REG_FIELD(ANA_TABLES_MACTINDX, 0, 10), [SYS_RESET_CFG_CORE_ENA] = REG_FIELD(SYS_RESET_CFG, 0, 0), [GCB_SOFT_RST_SWC_RST ] =REG_FIELD (GCB_SOFT_RST ,0 ,0 ), + /* Replicated per number of ports (7), register size 4 per port */ + [QSYS_SWITCH_PORT_MODE_PORT_ENA] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 14, 14, 7, 4), + [QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 11, 13, 7, 4), + [QSYS_SWITCH_PORT_MODE_YEL_RSRVD] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 10, 10, 7, 4), + [QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 9, 9, 7, 4), + [QSYS_SWITCH_PORT_MODE_TX_PFC_ENA] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 1, 8, 7, 4), + [QSYS_SWITCH_PORT_MODE_TX_PFC_MODE] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 0, 0, 7, 4), + [SYS_PORT_MODE_DATA_WO_TS] = REG_FIELD_ID(SYS_PORT_MODE, 5, 6, 7, 4), + [SYS_PORT_MODE_INCL_INJ_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 3, 4, 7, 4), + [SYS_PORT_MODE_INCL_XTR_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 1, 2, 7, 4), + [SYS_PORT_MODE_INCL_HDR_ERR] = REG_FIELD_ID(SYS_PORT_MODE, 0, 0, 7, 4), };static const struct ocelot_stat_layout vsc9959_stats_layout[] = {
drivers/net/ethernet/mscc/ocelot.c +22 -22
67 lines not on this page · raw message
drivers/net/ethernet/mscc/ocelot.h +0 -6
@@ -63,9 +63,6 @@ struct ocelot_port_private {u32 ocelot_port_readl (struct ocelot_port *port,u32 reg);void ocelot_port_writel (struct ocelot_port *port,u32 val,u32 reg); -#define ocelot_field_write (ocelot, reg, val) regmap_field_write((ocelot)->regfields[(reg)], (val)) -#define ocelot_field_read (ocelot, reg, val) regmap_field_read((ocelot)->regfields[(reg)], (val)) -int ocelot_chip_init (struct ocelot *ocelot,const struct ocelot_ops *ops);int ocelot_probe_port (struct ocelot *ocelot,int port,struct regmap *target,struct phy_device *phy);
@@ -78,7 +75,4 @@ extern struct notifier_block ocelot_netdevice_nb;extern struct notifier_block ocelot_switchdev_nb;extern struct notifier_block ocelot_switchdev_blocking_nb; -#define ocelot_field_write (ocelot, reg, val) regmap_field_write((ocelot)->regfields[(reg)], (val)) -#define ocelot_field_read (ocelot, reg, val) regmap_field_read((ocelot)->regfields[(reg)], (val)) -#endif
drivers/net/ethernet/mscc/ocelot_io.c +2 -0
@@ -89,6 +89,8 @@ int ocelot_regfields_init(struct ocelot *ocelot, regfield.reg = ocelot->map[target][reg ®_MASK ]; regfield.lsb = regfields[i].lsb; regfield.msb = regfields[i].msb; + regfield.id_size = regfields[i].id_size; + regfield.id_offset = regfields[i].id_offset; ocelot->regfields[i] = devm_regmap_field_alloc(ocelot->dev,
drivers/net/ethernet/mscc/ocelot_regs.c +11 -0
@@ -341,6 +341,17 @@ static const struct reg_field ocelot_regfields[REGFIELD_MAX] = { [SYS_RESET_CFG_CORE_ENA] = REG_FIELD(SYS_RESET_CFG, 2, 2), [SYS_RESET_CFG_MEM_ENA] = REG_FIELD(SYS_RESET_CFG, 1, 1), [SYS_RESET_CFG_MEM_INIT ] =REG_FIELD (SYS_RESET_CFG ,0 ,0 ), + /* Replicated per number of ports (11), register size 4 per port */ + [QSYS_SWITCH_PORT_MODE_PORT_ENA] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 14, 14, 11, 4), + [QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 11, 13, 11, 4), + [QSYS_SWITCH_PORT_MODE_YEL_RSRVD] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 10, 10, 11, 4), + [QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 9, 9, 11, 4), + [QSYS_SWITCH_PORT_MODE_TX_PFC_ENA] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 1, 8, 11, 4), + [QSYS_SWITCH_PORT_MODE_TX_PFC_MODE] = REG_FIELD_ID(QSYS_SWITCH_PORT_MODE, 0, 0, 11, 4), + [SYS_PORT_MODE_DATA_WO_TS] = REG_FIELD_ID(SYS_PORT_MODE, 5, 6, 11, 4), + [SYS_PORT_MODE_INCL_INJ_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 3, 4, 11, 4), + [SYS_PORT_MODE_INCL_XTR_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 1, 2, 11, 4), + [SYS_PORT_MODE_INCL_HDR_ERR] = REG_FIELD_ID(SYS_PORT_MODE, 0, 0, 11, 4), };static const struct ocelot_stat_layout ocelot_stats_layout[] = {
include/soc/mscc/ocelot.h +15 -0
@@ -475,11 +475,21 @@ enum ocelot_regfield {ANA_TABLES_MACACCESS_B_DOM ,ANA_TABLES_MACTINDX_BUCKET ,ANA_TABLES_MACTINDX_M_INDEX , +QSYS_SWITCH_PORT_MODE_PORT_ENA , +QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG , +QSYS_SWITCH_PORT_MODE_YEL_RSRVD , +QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE , +QSYS_SWITCH_PORT_MODE_TX_PFC_ENA , +QSYS_SWITCH_PORT_MODE_TX_PFC_MODE ,QSYS_TIMED_FRAME_ENTRY_TFRM_VLD ,QSYS_TIMED_FRAME_ENTRY_TFRM_FP ,QSYS_TIMED_FRAME_ENTRY_TFRM_PORTNO ,QSYS_TIMED_FRAME_ENTRY_TFRM_TM_SEL ,QSYS_TIMED_FRAME_ENTRY_TFRM_TM_T , +SYS_PORT_MODE_DATA_WO_TS , +SYS_PORT_MODE_INCL_INJ_HDR , +SYS_PORT_MODE_INCL_XTR_HDR , +SYS_PORT_MODE_INCL_HDR_ERR ,SYS_RESET_CFG_CORE_ENA ,SYS_RESET_CFG_MEM_ENA , SYS_RESET_CFG_MEM_INIT,
@@ -623,6 +633,11 @@ struct ocelot_policer {#define ocelot_rmw_rix (ocelot, val, m, reg, ri) __ocelot_rmw_ix(ocelot, val, m, reg, reg##_RSZ * (ri))#define ocelot_rmw (ocelot, val, m, reg) __ocelot_rmw_ix(ocelot, val, m, reg, 0) +#define ocelot_field_write (ocelot, reg, val) regmap_field_write((ocelot)->regfields[(reg)], (val)) +#define ocelot_field_read (ocelot, reg, val) regmap_field_read((ocelot)->regfields[(reg)], (val)) +#define ocelot_fields_write (ocelot, id, reg, val) regmap_fields_write((ocelot)->regfields[(reg)], (id), (val)) +#define ocelot_fields_read (ocelot, id, reg, val) regmap_fields_read((ocelot)->regfields[(reg)], (id), (val)) +/* I/O */ u32 ocelot_port_readl (struct ocelot_port *port,u32 reg);void ocelot_port_writel (struct ocelot_port *port,u32 val,u32 reg);
include/soc/mscc/ocelot_qsys.h +0 -13
@@ -13,19 +13,6 @@#define QSYS_PORT_MODE_DEQUEUE_DIS BIT(1)#define QSYS_PORT_MODE_DEQUEUE_LATE BIT(0) -#define QSYS_SWITCH_PORT_MODE_RSZ 0x4 - -#define QSYS_SWITCH_PORT_MODE_PORT_ENA BIT(14) -#define QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG (x) (((x) << 11) & GENMASK(13, 11)) -#define QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG_M GENMASK(13, 11) -#define QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG_X (x) (((x) & GENMASK(13, 11)) >> 11) -#define QSYS_SWITCH_PORT_MODE_YEL_RSRVD BIT(10) -#define QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE BIT(9) -#define QSYS_SWITCH_PORT_MODE_TX_PFC_ENA (x) (((x) << 1) & GENMASK(8, 1)) -#define QSYS_SWITCH_PORT_MODE_TX_PFC_ENA_M GENMASK(8, 1) -#define QSYS_SWITCH_PORT_MODE_TX_PFC_ENA_X (x) (((x) & GENMASK(8, 1)) >> 1) -#define QSYS_SWITCH_PORT_MODE_TX_PFC_MODE BIT(0) -#define QSYS_STAT_CNT_CFG_TX_GREEN_CNT_MODE BIT(5)#define QSYS_STAT_CNT_CFG_TX_YELLOW_CNT_MODE BIT(4)#define QSYS_STAT_CNT_CFG_DROP_GREEN_CNT_MODE BIT(3)
include/soc/mscc/ocelot_sys.h +0 -13
@@ -12,19 +12,6 @@#define SYS_COUNT_TX_OCTETS_RSZ 0x4 -#define SYS_PORT_MODE_RSZ 0x4 - -#define SYS_PORT_MODE_DATA_WO_TS (x) (((x) << 5) & GENMASK(6, 5)) -#define SYS_PORT_MODE_DATA_WO_TS_M GENMASK(6, 5) -#define SYS_PORT_MODE_DATA_WO_TS_X (x) (((x) & GENMASK(6, 5)) >> 5) -#define SYS_PORT_MODE_INCL_INJ_HDR (x) (((x) << 3) & GENMASK(4, 3)) -#define SYS_PORT_MODE_INCL_INJ_HDR_M GENMASK(4, 3) -#define SYS_PORT_MODE_INCL_INJ_HDR_X (x) (((x) & GENMASK(4, 3)) >> 3) -#define SYS_PORT_MODE_INCL_XTR_HDR (x) (((x) << 1) & GENMASK(2, 1)) -#define SYS_PORT_MODE_INCL_XTR_HDR_M GENMASK(2, 1) -#define SYS_PORT_MODE_INCL_XTR_HDR_X (x) (((x) & GENMASK(2, 1)) >> 1) -#define SYS_PORT_MODE_INJ_HDR_ERR BIT(0) -#define SYS_FRONT_PORT_MODE_RSZ 0x4#define SYS_FRONT_PORT_MODE_HDX_MODE BIT(0)
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 05/13] net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
Quoted 13 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
Currently Felix and Ocelot share the same bit layout in these per-port registers, but Seville does not. So we need
reg_fieldsfor that.Actually since these are per-port registers, we need to also specify the number of ports, and register size per port, and use the regmap API for multiple ports.
Signed-off-by Vladimir Oltean <[email protected]>---
Changes in v2:
None.
[snip]
drivers/net/dsa/ocelot/felix.c static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port, · line 316
Quoted 9 lines
drivers/net/dsa/ocelot/felix.c +4
-4/* Core: Enable port for frame transfer */ -ocelot_write_rix (ocelot,QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE | -QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG (1 ) | -QSYS_SWITCH_PORT_MODE_PORT_ENA , -QSYS_SWITCH_PORT_MODE , port); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE ,1 ); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_PORT_ENA ,1 );
I am a bit confused throughout this patch sometimes SCH_NEXT_CFG is set to 1, sometimes not, this makes it a bit harder to review the conversion, assuming this is fine:
Signature · 1 line
Florian
Vladimir Oltean
maintainerRe: [PATCH v2 net-next 05/13] net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
Hi Florian,
Quoted 31 lines · Florian Fainelli
Quoted 13 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
Currently Felix and Ocelot share the same bit layout in these per-port registers, but Seville does not. So we need
reg_fieldsfor that.Actually since these are per-port registers, we need to also specify the number of ports, and register size per port, and use the regmap API for multiple ports.
Signed-off-by Vladimir Oltean <[email protected]>---
Changes in v2:
None.[snip]
drivers/net/dsa/ocelot/felix.c static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port, · line 316
Quoted 9 lines
/* Core: Enable port for frame transfer */drivers/net/dsa/ocelot/felix.c +4
-4-ocelot_write_rix (ocelot,QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE | -QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG (1 ) | -QSYS_SWITCH_PORT_MODE_PORT_ENA , -QSYS_SWITCH_PORT_MODE , port); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE ,1 ); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_PORT_ENA ,1 );
Quoted 7 lines
I am a bit confused throughout this patch sometimes
SCH_NEXT_CFGis set to 1, sometimes not, this makes it a bit harder to review the conversion, assuming this is fine:Reviewed-by Florian Fainelli <[email protected]>--
Florian
Yes, this is a subtle point, but it's correct the way it is, and I didn't want to insist on the details of it, but now that you mentioned it, let's go.
Seville does not have the QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG register field at all. And using the previous API (ocelot_write_rix), we were only writing 1 for Felix and Ocelot, which was their hardware-default value, so we weren't changing its value in practice. So the equivalent with ocelot_fields_write would be to simply not do anything at all for the SCH_NEXT_CFG field, which is actually something that is required if we want to support Seville too.
Thank you so much for reviewing the entire series!
-Vladimir
Re: [PATCH v2 net-next 05/13] net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
Quoted 42 lines · Vladimir Oltean
Hi Florian,
Quoted 31 lines · Florian Fainelli
Quoted 13 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
Currently Felix and Ocelot share the same bit layout in these per-port registers, but Seville does not. So we need
reg_fieldsfor that.Actually since these are per-port registers, we need to also specify the number of ports, and register size per port, and use the regmap API for multiple ports.
Signed-off-by Vladimir Oltean <[email protected]>---
Changes in v2:
None.[snip]
drivers/net/dsa/ocelot/felix.c static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port, · line 316
Quoted 9 lines
/* Core: Enable port for frame transfer */drivers/net/dsa/ocelot/felix.c +4
-4-ocelot_write_rix (ocelot,QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE | -QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG (1 ) | -QSYS_SWITCH_PORT_MODE_PORT_ENA , -QSYS_SWITCH_PORT_MODE , port); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE ,1 ); +ocelot_fields_write (ocelot, port, +QSYS_SWITCH_PORT_MODE_PORT_ENA ,1 );Quoted 7 lines
I am a bit confused throughout this patch sometimes
SCH_NEXT_CFGis set to 1, sometimes not, this makes it a bit harder to review the conversion, assuming this is fine:Reviewed-by Florian Fainelli <[email protected]>--
Florian
Quoted 10 lines
Yes, this is a subtle point, but it's correct the way it is, and I didn't want to insist on the details of it, but now that you mentioned it, let's go.
Seville does not have theQSYS_SWITCH_PORT_MODE_SCH_NEXT_CFGregister field at all. And using the previous API (ocelot_write_rix), we were only writing 1 for Felix and Ocelot, which was their hardware-default value, so we weren't changing its value in practice. So the equivalent withocelot_fields_writewould be to simply not do anything at all for theSCH_NEXT_CFGfield, which is actually something that is required if we want to support Seville too.
OK, thank you for providing these details.
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 6/13 net: dsa: felix: create a template for the DSA tags on xmit
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact same bitfield layout for the DSA tags. The destination ports field is different for Seville VSC9953 for example. So the choices are to either duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow take into account a supposed ocelot->dest_ports_offset when packing this field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero and call some packing() functions of dubious performance in the fastpath. And most of the values it needs to pack are pretty much constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good if we could improve that.
The proposed solution is to allocate a memory area per port at probe time, initialize that with the statically defined bits as per chip hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1 bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like tag_brcm.c, which would have a separate .xmit function. Again, too much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c module, instead of from the driver: couldn't figure out a method of accessing the correct port template corresponding to the correct tagger in the .xmit function.
---
Changes in v2:
Created a function pointer such that Seville could reuse more code.
drivers/net/dsa/ocelot/felix.c | 13 +++++++++++++ drivers/net/dsa/ocelot/felix.h | 1 + drivers/net/dsa/ocelot/felix_vsc9959.c | 20 ++++++++++++++++++++ include/soc/mscc/ocelot.h | 2 ++ net/dsa/tag_ocelot.c | 21 ++++++++------------- 5 files changed, 44 insertions(+), 13 deletions(-)
drivers/net/dsa/ocelot/felix.c +13 -0
@@ -502,6 +502,7 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)for (port =0 ; port < num_phys_ports; port++) {struct ocelot_port *ocelot_port;struct regmap *target; +u8 *template; ocelot_port = devm_kzalloc(ocelot->dev, sizeof(struct ocelot_port),
@@ -527,10 +528,22 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)return PTR_ERR (target); } + template =devm_kzalloc (ocelot->dev,OCELOT_TAG_LEN , +GFP_KERNEL ); +if (!template) { +dev_err (ocelot->dev, +"Failed to allocate memory for DSA tag\n" ); +kfree (port_phy_modes); +return -ENOMEM ; + } + ocelot_port->phy_mode = port_phy_modes[port]; ocelot_port->ocelot = ocelot; ocelot_port->target = target; + ocelot_port->xmit_template = template; ocelot->ports[port] = ocelot_port; + + felix->info->xmit_template_populate (ocelot, port); }kfree (port_phy_modes);
drivers/net/dsa/ocelot/felix.h +1 -0
@@ -40,6 +40,7 @@ struct felix_info { enum tc_setup_type type, void *type_data);void (*port_sched_speed_set)(struct ocelot *ocelot,int port,u32 speed); +void (*xmit_template_populate)(struct ocelot *ocelot,int port); };extern struct felix_info felix_info_vsc9959;
drivers/net/dsa/ocelot/felix_vsc9959.c +20 -0
@@ -8,6 +8,7 @@#include <soc/mscc/ocelot_ptp.h> #include <soc/mscc/ocelot_sys.h> #include <soc/mscc/ocelot.h> +#include <linux/packing.h> #include <net/pkt_sched.h> #include <linux/iopoll.h> #include <linux/pci.h>
@@ -1446,6 +1447,24 @@ static int vsc9959_port_setup_tc(struct dsa_switch *ds, int port, } } +static void vsc9959_xmit_template_populate (struct ocelot *ocelot,int port) +{ +struct ocelot_port *ocelot_port = ocelot->ports[port]; +u8 *template = ocelot_port->xmit_template; +u64 bypass, dest, src; + +/* Set the source port as the CPU port module and not the +* NPI port +*/ + src = ocelot->num_phys_ports; + dest =BIT (port); + bypass = true; + +packing (template, &bypass,127 ,127 ,OCELOT_TAG_LEN ,PACK ,0 ); +packing (template, &dest,68 ,56 ,OCELOT_TAG_LEN ,PACK ,0 ); +packing (template, &src,46 ,43 ,OCELOT_TAG_LEN ,PACK ,0 ); +} +struct felix_info felix_info_vsc9959 = { .target_io_res = vsc9959_target_io_res, .port_io_res = vsc9959_port_io_res,
@@ -1472,4 +1491,5 @@ struct felix_info felix_info_vsc9959 = { .prevalidate_phy_mode = vsc9959_prevalidate_phy_mode, .port_setup_tc = vsc9959_port_setup_tc, .port_sched_speed_set = vsc9959_sched_speed_set, + .xmit_template_populate = vsc9959_xmit_template_populate, };
include/soc/mscc/ocelot.h +2 -0
@@ -549,6 +549,8 @@ struct ocelot_port {u8 ts_id;phy_interface_t phy_mode; + +u8 *xmit_template; };struct ocelot {
net/dsa/tag_ocelot.c +8 -13
@@ -137,11 +137,10 @@ static struct sk_buff *ocelot_xmit(struct sk_buff *skb, struct net_device *netdev) {struct dsa_port *dp =dsa_slave_to_port (netdev); -u64 bypass, dest, src, qos_class, rew_op;struct dsa_switch *ds = dp->ds; -int port = dp->index;struct ocelot *ocelot = ds->priv; -struct ocelot_port *ocelot_port = ocelot->ports[port]; +struct ocelot_port *ocelot_port; +u64 qos_class, rew_op;u8 *injection;if (unlikely (skb_cow_head (skb,OCELOT_TAG_LEN ) <0 )) {
@@ -149,19 +148,15 @@ static struct sk_buff *ocelot_xmit(struct sk_buff *skb,return NULL ; } - injection =skb_push (skb,OCELOT_TAG_LEN ); + ocelot_port = ocelot->ports[dp->index]; -memset (injection,0 ,OCELOT_TAG_LEN ); + injection =skb_push (skb,OCELOT_TAG_LEN ); -/* Set the source port as the CPU port module and not the NPI port */ - src = ocelot->num_phys_ports; - dest =BIT (port); - bypass = true; +memcpy (injection, ocelot_port->xmit_template,OCELOT_TAG_LEN ); +/* Fix up the fields which are not statically determined +* in the template +*/ qos_class = skb->priority; - -packing (injection, &bypass,127 ,127 ,OCELOT_TAG_LEN ,PACK ,0 ); -packing (injection, &dest,68 ,56 ,OCELOT_TAG_LEN ,PACK ,0 ); -packing (injection, &src,46 ,43 ,OCELOT_TAG_LEN ,PACK ,0 );packing (injection, &qos_class,19 ,17 ,OCELOT_TAG_LEN ,PACK ,0 );if (ocelot->ptp && (skb_shinfo (skb)->tx_flags &SKBTX_HW_TSTAMP )) {
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 06/13] net: dsa: felix: create a template for the DSA tags on xmit
Quoted 17 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use
tag_ocelot.cdon't have the exact same bitfield layout for the DSA tags. The destination ports field is different for Seville VSC9953 for example. So the choices are to either duplicatetag_ocelot.cinto a newtag_seville.c(sub-optimal) or somehow take into account a supposedocelot->dest_ports_offsetwhen packing this field into the DSA injection header (again not ideal).Secondly,
tag_ocelot.calready needs to memset a 128-bit area to zero and call somepacking()functions of dubious performance in the fastpath. And most of the values it needs to pack are pretty much constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good if we could improve that.
Quoted 7 lines
The proposed solution is to allocate a memory area per port at probe time, initialize that with the statically defined bits as per chip hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separatetag_seville.c: too much code duplication for just 1 bit field difference.
If this is really the only difference, we could have added a device ID or something that would allow tag_ocelot.c to differentiate Seville from Felix and just have a conditional for using the right definition.
The solution proposed here is okay and scales beyond a single bit field difference. Maybe this will open up the door for consolidating the various Microchip KSZ tag implementations at some point.
Signature · 1 line
Florian
Vladimir Oltean
maintainerRe: [PATCH v2 net-next 06/13] net: dsa: felix: create a template for the DSA tags on xmit
Hi Florian,
Quoted 33 lines · Florian Fainelli
Quoted 17 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use
tag_ocelot.cdon't have the exact same bitfield layout for the DSA tags. The destination ports field is different for Seville VSC9953 for example. So the choices are to either duplicatetag_ocelot.cinto a newtag_seville.c(sub-optimal) or somehow take into account a supposedocelot->dest_ports_offsetwhen packing this field into the DSA injection header (again not ideal).Secondly,
tag_ocelot.calready needs to memset a 128-bit area to zero and call somepacking()functions of dubious performance in the fastpath. And most of the values it needs to pack are pretty much constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good if we could improve that.Quoted 7 lines
The proposed solution is to allocate a memory area per port at probe time, initialize that with the statically defined bits as per chip hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separatetag_seville.c: too much code duplication for just 1 bit field difference.If this is really the only difference, we could have added a device ID or something that would allow
tag_ocelot.cto differentiate Seville from Felix and just have a conditional for using the right definition.
Quoted 7 lines
The solution proposed here is okay and scales beyond a single bit field difference. Maybe this will open up the door for consolidating the various Microchip KSZ tag implementations at some point.
Reviewed-by Florian Fainelli <[email protected]>--
Florian
Yes, but with a check for device id in the fast path, the xmit performance would have been slightly worse, and this way it is slightly better. Again, not the magnitude is important here (which is marginal either way), but the sign :)
Thanks,
-Vladimir
Vladimir Oltean
maintainerPATCH v2 7/13 net: mscc: ocelot: split writes to pause frame enable bit and to thresholds
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
We don't want ocelot_port_set_maxlen to enable pause frame TX, just to adjust the pause thresholds.
Move the unconditional enabling of pause TX to ocelot_init_port. There is no good place to put such setting because it shouldn't be unconditional. But at the moment it is, we're not changing that.
---
Changes in v2:
None.
drivers/net/ethernet/mscc/ocelot.c | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-)
drivers/net/ethernet/mscc/ocelot.c +12 -7
@@ -2013,6 +2013,7 @@ void ocelot_port_set_maxlen(struct ocelot *ocelot, int port, size_t sdu) {struct ocelot_port *ocelot_port = ocelot->ports[port];int maxlen = sdu +ETH_HLEN +ETH_FCS_LEN ; +int pause_start, pause_stop;int atop_wm;if (port == ocelot->npi) {
@@ -2026,13 +2027,13 @@ void ocelot_port_set_maxlen(struct ocelot *ocelot, int port, size_t sdu)ocelot_port_writel (ocelot_port, maxlen,DEV_MAC_MAXLEN_CFG ); -/* Set Pause WM hysteresis -* 152 = 6 * maxlen / OCELOT_BUFFER_CELL_SZ -* 101 = 4 * maxlen / OCELOT_BUFFER_CELL_SZ -*/ -ocelot_write_rix (ocelot,SYS_PAUSE_CFG_PAUSE_ENA | -SYS_PAUSE_CFG_PAUSE_STOP (101 ) | -SYS_PAUSE_CFG_PAUSE_START (152 ),SYS_PAUSE_CFG , port); +/* Set Pause watermark hysteresis */ + pause_start =6 * maxlen /OCELOT_BUFFER_CELL_SZ ; + pause_stop =4 * maxlen /OCELOT_BUFFER_CELL_SZ ; +ocelot_rmw_rix (ocelot,SYS_PAUSE_CFG_PAUSE_START (pause_start), +SYS_PAUSE_CFG_PAUSE_START_M ,SYS_PAUSE_CFG , port); +ocelot_rmw_rix (ocelot,SYS_PAUSE_CFG_PAUSE_STOP (pause_stop), +SYS_PAUSE_CFG_PAUSE_STOP_M ,SYS_PAUSE_CFG , port);/* Tail dropping watermark */ atop_wm = (ocelot->shared_queue_sz - 9 * maxlen) /
@@ -2095,6 +2096,10 @@ void ocelot_init_port(struct ocelot *ocelot, int port)ocelot_port_writel (ocelot_port,0 ,DEV_MAC_FC_MAC_HIGH_CFG );ocelot_port_writel (ocelot_port,0 ,DEV_MAC_FC_MAC_LOW_CFG ); +/* Enable transmission of pause frames */ +ocelot_rmw_rix (ocelot,SYS_PAUSE_CFG_PAUSE_ENA ,SYS_PAUSE_CFG_PAUSE_ENA , +SYS_PAUSE_CFG , port); +/* Drop frames with multicast source address */ ocelot_rmw_gix(ocelot, ANA_PORT_DROP_CFG_DROP_MC_SMAC_ENA, ANA_PORT_DROP_CFG_DROP_MC_SMAC_ENA,
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 07/13] net: mscc: ocelot: split writes to pause frame enable bit and to thresholds
Quoted 10 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
We don't want
ocelot_port_set_maxlento enable pause frame TX, just to adjust the pause thresholds.Move the unconditional enabling of pause TX to
ocelot_init_port. There is no good place to put such setting because it shouldn't be unconditional. But at the moment it is, we're not changing that.Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 8/13 net: mscc: ocelot: disable flow control on NPI interface
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
The Ocelot switches do not support flow control on Ethernet interfaces where a DSA tag must be added. If pause frames are enabled, they will be encapsulated in the DSA tag just like regular frames, and the DSA master will not recognize them.
---
Changes in v2:
None.
drivers/net/ethernet/mscc/ocelot.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/net/ethernet/mscc/ocelot.c +4 -0
@@ -2202,6 +2202,10 @@ void ocelot_configure_cpu(struct ocelot *ocelot, int npi, extraction);ocelot_fields_write (ocelot, npi,SYS_PORT_MODE_INCL_INJ_HDR , injection); + +/* Disable transmission of pause frames */ +ocelot_rmw_rix (ocelot,0 ,SYS_PAUSE_CFG_PAUSE_ENA , +SYS_PAUSE_CFG , npi); }/* Enable CPU port module */
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 08/13] net: mscc: ocelot: disable flow control on NPI interface
Quoted 8 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
The Ocelot switches do not support flow control on Ethernet interfaces where a DSA tag must be added. If pause frames are enabled, they will be encapsulated in the DSA tag just like regular frames, and the DSA master will not recognize them.
Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 9/13 net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
In reply to Vladimir OlteanFrom: Maxim Kochetkov <[email protected]>
Seville has a different bitwise layout than Ocelot and Felix.
---
Changes in v2:
None.
drivers/net/dsa/ocelot/felix_vsc9959.c | 3 +++ drivers/net/ethernet/mscc/ocelot.c | 14 ++++++-------- drivers/net/ethernet/mscc/ocelot_regs.c | 3 +++ include/soc/mscc/ocelot.h | 3 +++ include/soc/mscc/ocelot_sys.h | 10 ---------- 5 files changed, 15 insertions(+), 18 deletions(-)
drivers/net/dsa/ocelot/felix_vsc9959.c +3 -0
@@ -515,6 +515,9 @@ static const struct reg_field vsc9959_regfields[REGFIELD_MAX] = { [SYS_PORT_MODE_INCL_INJ_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 3, 4, 7, 4), [SYS_PORT_MODE_INCL_XTR_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 1, 2, 7, 4), [SYS_PORT_MODE_INCL_HDR_ERR] = REG_FIELD_ID(SYS_PORT_MODE, 0, 0, 7, 4), + [SYS_PAUSE_CFG_PAUSE_START] = REG_FIELD_ID(SYS_PAUSE_CFG, 10, 18, 7, 4), + [SYS_PAUSE_CFG_PAUSE_STOP] = REG_FIELD_ID(SYS_PAUSE_CFG, 1, 9, 7, 4), + [SYS_PAUSE_CFG_PAUSE_ENA] = REG_FIELD_ID(SYS_PAUSE_CFG, 0, 1, 7, 4), };static const struct ocelot_stat_layout vsc9959_stats_layout[] = {
drivers/net/ethernet/mscc/ocelot.c +6 -8
@@ -2030,10 +2030,10 @@ void ocelot_port_set_maxlen(struct ocelot *ocelot, int port, size_t sdu)/* Set Pause watermark hysteresis */ pause_start =6 * maxlen /OCELOT_BUFFER_CELL_SZ ; pause_stop =4 * maxlen /OCELOT_BUFFER_CELL_SZ ; -ocelot_rmw_rix (ocelot,SYS_PAUSE_CFG_PAUSE_START (pause_start), -SYS_PAUSE_CFG_PAUSE_START_M ,SYS_PAUSE_CFG , port); -ocelot_rmw_rix (ocelot,SYS_PAUSE_CFG_PAUSE_STOP (pause_stop), -SYS_PAUSE_CFG_PAUSE_STOP_M ,SYS_PAUSE_CFG , port); +ocelot_fields_write (ocelot, port,SYS_PAUSE_CFG_PAUSE_START , + pause_start); +ocelot_fields_write (ocelot, port,SYS_PAUSE_CFG_PAUSE_STOP , + pause_stop);/* Tail dropping watermark */ atop_wm = (ocelot->shared_queue_sz - 9 * maxlen) /
@@ -2097,8 +2097,7 @@ void ocelot_init_port(struct ocelot *ocelot, int port)ocelot_port_writel (ocelot_port,0 ,DEV_MAC_FC_MAC_LOW_CFG );/* Enable transmission of pause frames */ -ocelot_rmw_rix (ocelot,SYS_PAUSE_CFG_PAUSE_ENA ,SYS_PAUSE_CFG_PAUSE_ENA , -SYS_PAUSE_CFG , port); +ocelot_fields_write (ocelot, port,SYS_PAUSE_CFG_PAUSE_ENA ,1 );/* Drop frames with multicast source address */ ocelot_rmw_gix(ocelot, ANA_PORT_DROP_CFG_DROP_MC_SMAC_ENA,
@@ -2204,8 +2203,7 @@ void ocelot_configure_cpu(struct ocelot *ocelot, int npi, injection);/* Disable transmission of pause frames */ -ocelot_rmw_rix (ocelot,0 ,SYS_PAUSE_CFG_PAUSE_ENA , -SYS_PAUSE_CFG , npi); +ocelot_fields_write (ocelot, npi,SYS_PAUSE_CFG_PAUSE_ENA ,0 ); }/* Enable CPU port module */
drivers/net/ethernet/mscc/ocelot_regs.c +3 -0
@@ -352,6 +352,9 @@ static const struct reg_field ocelot_regfields[REGFIELD_MAX] = { [SYS_PORT_MODE_INCL_INJ_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 3, 4, 11, 4), [SYS_PORT_MODE_INCL_XTR_HDR] = REG_FIELD_ID(SYS_PORT_MODE, 1, 2, 11, 4), [SYS_PORT_MODE_INCL_HDR_ERR] = REG_FIELD_ID(SYS_PORT_MODE, 0, 0, 11, 4), + [SYS_PAUSE_CFG_PAUSE_START] = REG_FIELD_ID(SYS_PAUSE_CFG, 10, 18, 11, 4), + [SYS_PAUSE_CFG_PAUSE_STOP] = REG_FIELD_ID(SYS_PAUSE_CFG, 1, 9, 11, 4), + [SYS_PAUSE_CFG_PAUSE_ENA] = REG_FIELD_ID(SYS_PAUSE_CFG, 0, 1, 11, 4), };static const struct ocelot_stat_layout ocelot_stats_layout[] = {
include/soc/mscc/ocelot.h +3 -0
@@ -496,6 +496,9 @@ enum ocelot_regfield {GCB_SOFT_RST_SWC_RST ,GCB_MIIM_MII_STATUS_PENDING ,GCB_MIIM_MII_STATUS_BUSY , +SYS_PAUSE_CFG_PAUSE_START , +SYS_PAUSE_CFG_PAUSE_STOP , +SYS_PAUSE_CFG_PAUSE_ENA , REGFIELD_MAX };
include/soc/mscc/ocelot_sys.h +0 -10
@@ -43,16 +43,6 @@#define SYS_TIMESTAMP_OFFSET_TIMESTAMP_OFFSET (x) ((x) & GENMASK(5, 0))#define SYS_TIMESTAMP_OFFSET_TIMESTAMP_OFFSET_M GENMASK(5, 0) -#define SYS_PAUSE_CFG_RSZ 0x4 - -#define SYS_PAUSE_CFG_PAUSE_START (x) (((x) << 10) & GENMASK(18, 10)) -#define SYS_PAUSE_CFG_PAUSE_START_M GENMASK(18, 10) -#define SYS_PAUSE_CFG_PAUSE_START_X (x) (((x) & GENMASK(18, 10)) >> 10) -#define SYS_PAUSE_CFG_PAUSE_STOP (x) (((x) << 1) & GENMASK(9, 1)) -#define SYS_PAUSE_CFG_PAUSE_STOP_M GENMASK(9, 1) -#define SYS_PAUSE_CFG_PAUSE_STOP_X (x) (((x) & GENMASK(9, 1)) >> 1) -#define SYS_PAUSE_CFG_PAUSE_ENA BIT(0) -#define SYS_PAUSE_TOT_CFG_PAUSE_TOT_START (x) (((x) << 9) & GENMASK(17, 9))#define SYS_PAUSE_TOT_CFG_PAUSE_TOT_START_M GENMASK(17, 9)#define SYS_PAUSE_TOT_CFG_PAUSE_TOT_START_X (x) (((x) & GENMASK(17, 9)) >> 9)
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 09/13] net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
Quoted 6 lines · Vladimir Oltean
From: Maxim Kochetkov <[email protected]>
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by Maxim Kochetkov <[email protected]>Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 10/13 net: mscc: ocelot: extend watermark encoding function
In reply to Vladimir OlteanFrom: Maxim Kochetkov <[email protected]>
The ocelot_wm_encode function deals with setting thresholds for pause frame start and stop. In Ocelot and Felix the register layout is the same, but for Seville, it isn't. The easiest way to accommodate Seville hardware configuration is to introduce a function pointer for setting this up.
---
Changes in v2:
None.
drivers/net/dsa/ocelot/felix_vsc9959.c | 13 +++++++++++++ drivers/net/ethernet/mscc/ocelot.c | 16 ++-------------- drivers/net/ethernet/mscc/ocelot_board.c | 13 +++++++++++++ include/soc/mscc/ocelot.h | 1 + 4 files changed, 29 insertions(+), 14 deletions(-)
drivers/net/dsa/ocelot/felix_vsc9959.c +13 -0
@@ -1163,8 +1163,21 @@ static int vsc9959_prevalidate_phy_mode(struct ocelot *ocelot, int port, } } +/* Watermark encode +* Bit 8: Unit; 0:1, 1:16 +* Bit 7-0: Value to be multiplied with unit +*/ +static u16 vsc9959_wm_enc (u16 value) +{ +if (value >=BIT (8 )) +return BIT (8 ) | (value /16 ); + +return value; +} +static const struct ocelot_ops vsc9959_ops = { .reset = vsc9959_reset, + .wm_enc = vsc9959_wm_enc, };static int vsc9959_mdio_bus_alloc (struct ocelot *ocelot)
drivers/net/ethernet/mscc/ocelot.c +2 -14
@@ -396,18 +396,6 @@ static void ocelot_vlan_init(struct ocelot *ocelot) } } -/* Watermark encode -* Bit 8: Unit; 0:1, 1:16 -* Bit 7-0: Value to be multiplied with unit -*/ -static u16 ocelot_wm_enc (u16 value) -{ -if (value >=BIT (8 )) -return BIT (8 ) | (value /16 ); - -return value; -} -void ocelot_adjust_link (struct ocelot *ocelot,int port,struct phy_device *phydev) {
@@ -2038,9 +2026,9 @@ void ocelot_port_set_maxlen(struct ocelot *ocelot, int port, size_t sdu)/* Tail dropping watermark */ atop_wm = (ocelot->shared_queue_sz -9 * maxlen) /OCELOT_BUFFER_CELL_SZ ; -ocelot_write_rix (ocelot,ocelot_wm_enc (9 * maxlen), +ocelot_write_rix (ocelot, ocelot->ops->wm_enc (9 * maxlen),SYS_ATOP , port); -ocelot_write (ocelot,ocelot_wm_enc (atop_wm),SYS_ATOP_TOT_CFG ); +ocelot_write (ocelot, ocelot->ops->wm_enc (atop_wm),SYS_ATOP_TOT_CFG ); }EXPORT_SYMBOL (ocelot_port_set_maxlen);
drivers/net/ethernet/mscc/ocelot_board.c +13 -0
@@ -240,8 +240,21 @@ static int ocelot_reset(struct ocelot *ocelot)return 0 ; } +/* Watermark encode +* Bit 8: Unit; 0:1, 1:16 +* Bit 7-0: Value to be multiplied with unit +*/ +static u16 ocelot_wm_enc (u16 value) +{ +if (value >=BIT (8 )) +return BIT (8 ) | (value /16 ); + +return value; +} +static const struct ocelot_ops ocelot_ops = { .reset = ocelot_reset, + .wm_enc = ocelot_wm_enc, };static const struct vcap_field vsc7514_vcap_is2_keys[] = {
include/soc/mscc/ocelot.h +1 -0
@@ -526,6 +526,7 @@ struct ocelot;struct ocelot_ops {int (*reset)(struct ocelot *ocelot); +u16 (*wm_enc)(u16 value); };struct ocelot_acl_block {
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 10/13] net: mscc: ocelot: extend watermark encoding function
Quoted 10 lines · Vladimir Oltean
From: Maxim Kochetkov <[email protected]>
The
ocelot_wm_encodefunction deals with setting thresholds for pause frame start and stop. In Ocelot and Felix the register layout is the same, but for Seville, it isn't. The easiest way to accommodate Seville hardware configuration is to introduce a function pointer for setting this up.Signed-off-by Maxim Kochetkov <[email protected]>Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 11/13 net: dsa: felix: support half-duplex link modes
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx [ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x4
[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down [ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off
[root@LS1028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes (...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 0.383/0.611/1.051 ms
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x10
[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down [ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes (...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss round-trip min/avg/max = 0.301/0.384/1.138 ms
---
Patch resent from:
https://patchwork.ozlabs.org/project/netdev/patch/[email protected]/
Changes in v2:
Added spaces before the ping output in the commit message.
drivers/net/dsa/ocelot/felix.c | 4 +++- drivers/net/dsa/ocelot/felix_vsc9959.c | 13 ++++++++----- 2 files changed, 11 insertions(+), 6 deletions(-)
drivers/net/dsa/ocelot/felix.c +3 -1
@@ -167,14 +167,16 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port,return ; } -/* No half-duplex. */ phylink_set_port_modes (mask);phylink_set (mask, Autoneg);phylink_set (mask, Pause);phylink_set (mask, Asym_Pause); phylink_set(mask, 10baseT_Full); + phylink_set(mask, 10baseT_Half); phylink_set(mask, 100baseT_Full); + phylink_set(mask, 100baseT_Half); phylink_set(mask, 1000baseT_Full); + phylink_set(mask, 1000baseT_Half); if (state->interface == PHY_INTERFACE_MODE_INTERNAL || state->interface == PHY_INTERFACE_MODE_2500BASEX ||
drivers/net/dsa/ocelot/felix_vsc9959.c +8 -5
@@ -875,12 +875,12 @@ static void vsc9959_pcs_init_sgmii(struct phy_device *pcs,phy_write (pcs,MII_BMCR ,BMCR_ANRESTART |BMCR_ANENABLE ); }else { +u16 duplex =0 ;int speed; -if (state->duplex ==DUPLEX_HALF ) { -phydev_err (pcs,"Half duplex not supported\n" ); -return ; - } +if (state->duplex ==DUPLEX_FULL ) + duplex =BMCR_FULLDPLX ; +switch (state->speed) {case SPEED_1000 : speed =ENETC_PCS_SPEED_1000 ;
@@ -906,7 +906,7 @@ static void vsc9959_pcs_init_sgmii(struct phy_device *pcs,/* Yes, not a mistake: speed is given by IF_MODE. */ phy_write (pcs,MII_BMCR ,BMCR_RESET |BMCR_SPEED1000 | -BMCR_FULLDPLX ); + duplex); } }
@@ -983,8 +983,11 @@ static void vsc9959_pcs_init(struct ocelot *ocelot, int port,ARRAY_SIZE (phy_basic_ports_array), pcs->supported);linkmode_set_bit (ETHTOOL_LINK_MODE_10baseT_Full_BIT, pcs->supported); +linkmode_set_bit (ETHTOOL_LINK_MODE_10baseT_Half_BIT, pcs->supported);linkmode_set_bit (ETHTOOL_LINK_MODE_100baseT_Full_BIT, pcs->supported); +linkmode_set_bit (ETHTOOL_LINK_MODE_100baseT_Half_BIT, pcs->supported);linkmode_set_bit (ETHTOOL_LINK_MODE_1000baseT_Full_BIT, pcs->supported); +linkmode_set_bit (ETHTOOL_LINK_MODE_1000baseT_Half_BIT, pcs->supported);if (pcs->interface ==PHY_INTERFACE_MODE_2500BASEX || pcs->interface ==PHY_INTERFACE_MODE_USXGMII ) linkmode_set_bit(ETHTOOL_LINK_MODE_2500baseX_Full_BIT,
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 11/13] net: dsa: felix: support half-duplex link modes
Quoted 32 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx [ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready[root@LS1028ARDB ~] # ethtool -s swp0 advertise
0x4[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down [ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off[root@LS1028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes (...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 0.383/0.611/1.051 ms[root@LS1028ARDB ~] # ethtool -s swp0 advertise
0x10[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down [ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes (...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss round-trip min/avg/max = 0.301/0.384/1.138 ms
Quoted 1 line
Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 12/13 net: dsa: felix: move probing to felix_vsc9959.c
In reply to Vladimir OlteanFrom: Vladimir Oltean <[email protected]>
Felix is not actually meant to be a DSA driver only for the switch inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi / Microchip switches that are register-compatible with Ocelot and that are using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough to be used by other non-PCI switches, we need to move the PCI-specific probing to the low-level translation module felix_vsc9959.c. This way, other switches can have their own probing functions, as platform devices or otherwise.
This patch also removes the "Felix instance table", which did not stand the test of time and is unnecessary at this point.
---
Changes in v2:
Patch is new.
drivers/net/dsa/ocelot/felix.c | 194 +------------------------ drivers/net/dsa/ocelot/felix.h | 14 +- drivers/net/dsa/ocelot/felix_vsc9959.c | 192 +++++++++++++++++++++++- 3 files changed, 200 insertions(+), 200 deletions(-)
drivers/net/dsa/ocelot/felix.c +8 -186
@@ -158,37 +158,10 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port, struct phylink_link_state *state) {struct ocelot *ocelot = ds->priv; -struct ocelot_port *ocelot_port = ocelot->ports[port]; -__ETHTOOL_DECLARE_LINK_MODE_MASK (mask) = {0 , }; - -if (state->interface !=PHY_INTERFACE_MODE_NA && - state->interface != ocelot_port->phy_mode) { -bitmap_zero (supported, __ETHTOOL_LINK_MODE_MASK_NBITS); -return ; - } - -phylink_set_port_modes (mask); -phylink_set (mask, Autoneg); -phylink_set (mask, Pause); -phylink_set (mask, Asym_Pause); - phylink_set(mask, 10baseT_Full); - phylink_set(mask, 10baseT_Half); - phylink_set(mask, 100baseT_Full); - phylink_set(mask, 100baseT_Half); - phylink_set(mask, 1000baseT_Full); - phylink_set(mask, 1000baseT_Half); - -if (state->interface ==PHY_INTERFACE_MODE_INTERNAL || - state->interface ==PHY_INTERFACE_MODE_2500BASEX || - state->interface ==PHY_INTERFACE_MODE_USXGMII ) { - phylink_set(mask, 2500baseT_Full); - phylink_set(mask, 2500baseX_Full); - } +struct felix *felix =ocelot_to_felix (ocelot); -bitmap_and (supported, supported, mask, - __ETHTOOL_LINK_MODE_MASK_NBITS); -bitmap_and (state->advertising, state->advertising, mask, - __ETHTOOL_LINK_MODE_MASK_NBITS); +if (felix->info->phylink_validate) + felix->info->phylink_validate (ocelot, port, supported, state); } static int felix_phylink_mac_pcs_get_state(struct dsa_switch *ds, int port,
@@ -438,7 +411,6 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports) {struct ocelot *ocelot = &felix->ocelot;phy_interface_t *port_phy_modes; -resource_size_t switch_base;struct resource res;int port, i, err;
@@ -469,9 +441,6 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)return err; } - switch_base =pci_resource_start (felix->pdev, - felix->info->switch_pci_bar); -for (i =0 ; i <TARGET_MAX ; i++) {struct regmap *target;
@@ -480,8 +449,8 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)memcpy (&res, &felix->info->target_io_res[i],sizeof (res)); res.flags =IORESOURCE_MEM ; - res.start += switch_base; - res.end += switch_base; + res.start += felix->switch_base; + res.end += felix->switch_base; target =ocelot_regmap_init (ocelot, &res);if (IS_ERR (target)) {
@@ -518,8 +487,8 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)memcpy (&res, &felix->info->port_io_res[port],sizeof (res)); res.flags =IORESOURCE_MEM ; - res.start += switch_base; - res.end += switch_base; + res.start += felix->switch_base; + res.end += felix->switch_base; target =ocelot_regmap_init (ocelot, &res);if (IS_ERR (target)) {
@@ -786,7 +755,7 @@ static int felix_port_setup_tc(struct dsa_switch *ds, int port,return -EOPNOTSUPP ; } -static const struct dsa_switch_ops felix_switch_ops = { +const struct dsa_switch_ops felix_switch_ops = { .get_tag_protocol = felix_get_tag_protocol, .setup = felix_setup, .teardown = felix_teardown,
@@ -826,150 +795,3 @@ static const struct dsa_switch_ops felix_switch_ops = { .cls_flower_stats = felix_cls_flower_stats, .port_setup_tc = felix_port_setup_tc, }; - -static struct felix_info *felix_instance_tbl[] = { - [FELIX_INSTANCE_VSC9959 ] = &felix_info_vsc9959, -}; - -static irqreturn_t felix_irq_handler (int irq,void *data) -{ -struct ocelot *ocelot = (struct ocelot *)data; - -/* The INTB interrupt is used for both PTP TX timestamp interrupt -* and preemption status change interrupt on each port. -* -* - Get txtstamp if have -* - TODO: handle preemption. Without handling it, driver may get -* interrupt storm. -*/ - -ocelot_get_txtstamp (ocelot); - -return IRQ_HANDLED ; -} - -static int felix_pci_probe (struct pci_dev *pdev, -const struct pci_device_id *id) -{ -enum felix_instance instance = id->driver_data; -struct dsa_switch *ds; -struct ocelot *ocelot; -struct felix *felix; -int err; - -if (pdev->dev.of_node && !of_device_is_available (pdev->dev.of_node)) { -dev_info (&pdev->dev,"device is disabled, skipping\n" ); -return -ENODEV ; - } - - err =pci_enable_device (pdev); -if (err) { -dev_err (&pdev->dev,"device enable failed\n" ); - goto err_pci_enable; - } - -/* set up for high or low dma */ - err =dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (64 )); -if (err) { - err =dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (32 )); -if (err) { -dev_err (&pdev->dev, -"DMA configuration failed: 0x%x\n" , err); - goto err_dma; - } - } - - felix =kzalloc (sizeof (struct felix ),GFP_KERNEL ); -if (!felix) { - err = -ENOMEM ; -dev_err (&pdev->dev,"Failed to allocate driver memory\n" ); - goto err_alloc_felix; - } - -pci_set_drvdata (pdev, felix); - ocelot = &felix->ocelot; - ocelot->dev = &pdev->dev; - felix->pdev = pdev; - felix->info = felix_instance_tbl[instance]; - -pci_set_master (pdev); - - err =devm_request_threaded_irq (&pdev->dev, pdev->irq,NULL , - &felix_irq_handler,IRQF_ONESHOT , -"felix-intb" , ocelot); -if (err) { -dev_err (&pdev->dev,"Failed to request irq\n" ); - goto err_alloc_irq; - } - - ocelot->ptp =1 ; - - ds =kzalloc (sizeof (struct dsa_switch ),GFP_KERNEL ); -if (!ds) { - err = -ENOMEM ; -dev_err (&pdev->dev,"Failed to allocate DSA switch\n" ); - goto err_alloc_ds; - } - - ds->dev = &pdev->dev; - ds->num_ports = felix->info->num_ports; - ds->num_tx_queues = felix->info->num_tx_queues; - ds->ops = &felix_switch_ops; - ds->priv = ocelot; - felix->ds = ds; - - err =dsa_register_switch (ds); -if (err) { -dev_err (&pdev->dev,"Failed to register DSA switch: %d\n" , err); - goto err_register_ds; - } - -return 0 ; - -err_register_ds: -kfree (ds); -err_alloc_ds: -err_alloc_irq: -err_alloc_felix: -kfree (felix); -err_dma: -pci_disable_device (pdev); -err_pci_enable: -return err; -} - -static void felix_pci_remove (struct pci_dev *pdev) -{ -struct felix *felix; - - felix =pci_get_drvdata (pdev); - -dsa_unregister_switch (felix->ds); - -kfree (felix->ds); -kfree (felix); - -pci_disable_device (pdev); -} - -static struct pci_device_id felix_ids[] = { - { -/* NXP LS1028A */ -PCI_DEVICE (PCI_VENDOR_ID_FREESCALE ,0xEEF0 ), - .driver_data =FELIX_INSTANCE_VSC9959 , - }, - {0 , } -}; -MODULE_DEVICE_TABLE (pci, felix_ids); - -static struct pci_driver felix_pci_driver = { - .name =KBUILD_MODNAME , - .id_table = felix_ids, - .probe = felix_pci_probe, - .remove = felix_pci_remove, -}; - -module_pci_driver (felix_pci_driver); - -MODULE_DESCRIPTION ("Felix Switch driver" ); -MODULE_LICENSE ("GPL v2" );
drivers/net/dsa/ocelot/felix.h +7 -7
@@ -34,6 +34,9 @@ struct felix_info {void (*pcs_an_restart)(struct ocelot *ocelot,int port);void (*pcs_link_state)(struct ocelot *ocelot,int port,struct phylink_link_state *state); +void (*phylink_validate)(struct ocelot *ocelot,int port, +unsigned long *supported, +struct phylink_link_state *state);int (*prevalidate_phy_mode)(struct ocelot *ocelot,int port,phy_interface_t phy_mode); int (*port_setup_tc)(struct dsa_switch *ds, int port,
@@ -43,20 +46,17 @@ struct felix_info { void (*xmit_template_populate)(struct ocelot *ocelot, int port); }; -extern struct felix_info felix_info_vsc9959; - -enum felix_instance { -FELIX_INSTANCE_VSC9959 =0 , -}; +extern const struct dsa_switch_ops felix_switch_ops;/* DSA glue / front-end for struct ocelot */ struct felix {struct dsa_switch *ds; -struct pci_dev *pdev; -struct felix_info *info; +const struct felix_info *info;struct ocelot ocelot;struct mii_bus *imdio;struct phy_device **pcs; +resource_size_t switch_base; +resource_size_t imdio_base; };#endif
drivers/net/dsa/ocelot/felix_vsc9959.c +185 -7
226 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 12/13] net: dsa: felix: move probing to felix_vsc9959.c
Quoted 13 lines · Vladimir Oltean
From: Vladimir Oltean <[email protected]>
Felix is not actually meant to be a DSA driver only for the switch inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi / Microchip switches that are register-compatible with Ocelot and that are using in DSA mode (with an NPI Ethernet port).
For the
dsa_switch_opsexported by the felix driver to be generic enough to be used by other non-PCI switches, we need to move the PCI-specific probing to the low-level translation modulefelix_vsc9959.c. This way, other switches can have their own probing functions, as platform devices or otherwise.
Quoted 4 lines
This patch also removes the "Felix instance table", which did not stand the test of time and is unnecessary at this point.
Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
Vladimir Oltean
maintainerPATCH v2 13/13 net: dsa: felix: introduce support for Seville VSC9953 switch
In reply to Vladimir OlteanFrom: Maxim Kochetkov <[email protected]>
This is another switch from Vitesse / Microsemi / Microchip, that has 10 port (8 external, 2 internal) and is integrated into the Freescale / NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A, except that this is a platform device and Felix is a PCI device, and it doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus using a phy_device abstraction for it (yes, it will be refactored to use a raw mdio_device, like other phylink drivers do, but let's keep it like that for now). But unlike Felix, the MDIO bus and the PCS are not from the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it would be difficult to reuse that driver (it doesn't even use regmap, and it's less than 200 lines of code), so we hand-roll here some internal MDIO bus accessors within seville_vsc9953.c, which serves the purpose of driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of SerDes protocol, so we need to do pre-validation of PHY mode from device tree and not let phylink change it.
---
Changes in v2:
Now supporting Seville as part of the Felix driver. This has several
advantages: a lot more code reuse (not only from felix.c, but also from the low-level felix_vsc9959.c, the PCS initialization being an example). But also a disadvantage: the common driver depends on PCI, but Seville is not a PCI device.
Added devicetree bindings documentation.
.../devicetree/bindings/net/dsa/ocelot.txt | 106 +- drivers/net/dsa/ocelot/Kconfig | 12 +- drivers/net/dsa/ocelot/Makefile | 3 +- drivers/net/dsa/ocelot/felix.h | 7 + drivers/net/dsa/ocelot/felix_vsc9959.c | 12 +- drivers/net/dsa/ocelot/seville_vsc9953.c | 1111 +++++++++++++++++ 6 files changed, 1236 insertions(+), 15 deletions(-) create mode 100644 drivers/net/dsa/ocelot/seville_vsc9953.c
Documentation/devicetree/bindings/net/dsa/ocelot.txt +102 -4
@@ -4,10 +4,15 @@ Microchip Ocelot switch driver family Felix ----- -The VSC9959 core is currently the only switch supported by the driver, and is -found in the NXP LS1028A. It is a PCI device, part of the larger ENETC root -complex. As a result, the ethernet-switch node is a sub-node of the PCIe root -complex node and its "reg" property conforms to the parent node bindings: +Currently the switches supported by the felix driver are: + +- VSC9959 (Felix) +- VSC9953 (Seville) + +The VSC9959 switch is found in the NXP LS1028A. It is a PCI device, part of the +larger ENETC root complex. As a result, the ethernet-switch node is a sub-node +of the PCIe root complex node and its "reg" property conforms to the parent +node bindings: * reg: Specifies PCIe Device Number and Function Number of the endpoint device, in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0).
@@ -114,3 +119,96 @@ Example: }; }; }; + +The VSC9953 switch is found inside NXP T1040. It is a platform device with the +following required properties: + +- compatible: + Must be "mscc,vsc9953-switch". + +Supported PHY interface types (appropriate SerDes protocol setting changes are +needed in the RCW binary): + +* phy_mode = "internal": on ports 8 and 9 +* phy_mode = "sgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 +* phy_mode = "qsgmii": on ports 0, 1, 2, 3, 4, 5, 6, 7 +* phy_mode = "2500base-x": on ports 0, 1, 2, 3, 4, 5, 6, 7 + +Example: + +&soc { + ethernet-switch@800000 { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "mscc,vsc9953-switch"; + little-endian; + reg = <0x800000 0x290000>; + + ports { + #address-cells = <0x1>; + #size-cells = <0x0>; + + port@0 { + reg = <0x0>; + label = "swp0"; + }; + + port@1 { + reg = <0x1>; + label = "swp1"; + }; + + port@2 { + reg = <0x2>; + label = "swp2"; + }; + + port@3 { + reg = <0x3>; + label = "swp3"; + }; + + port@4 { + reg = <0x4>; + label = "swp4"; + }; + + port@5 { + reg = <0x5>; + label = "swp5"; + }; + + port@6 { + reg = <0x6>; + label = "swp6"; + }; + + port@7 { + reg = <0x7>; + label = "swp7"; + }; + + port@8 { + reg = <0x8>; + phy-mode = "internal"; + ethernet = <&enet0>; + + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + + port@9 { + reg = <0x9>; + phy-mode = "internal"; + status = "disabled"; + + fixed-link { + speed = <2500>; + full-duplex; + }; + }; + }; + }; +};
drivers/net/dsa/ocelot/Kconfig +8 -4
@@ -8,7 +8,11 @@ config NET_DSA_MSCC_FELIX select NET_DSA_TAG_OCELOT select FSL_ENETC_MDIO help - This driver supports the VSC9959 network switch, which is a member of - the Vitesse / Microsemi / Microchip Ocelot family of switching cores. - It is embedded as a PCIe function of the NXP LS1028A ENETC integrated - endpoint. + This driver supports network switches from the the Vitesse / + Microsemi / Microchip Ocelot family of switching cores that are + connected to their host CPU via Ethernet. + The following switches are supported: + - VSC9959 (Felix): embedded as a PCIe function of the NXP LS1028A + ENETC integrated endpoint. + - VSC9953 (Seville): embedded as a platform device on the + NXP T1040 SoC.
drivers/net/dsa/ocelot/Makefile +2 -1
@@ -3,4 +3,5 @@ obj-$(CONFIG_NET_DSA_MSCC_FELIX) += mscc_felix.o mscc_felix-objs := \ felix.o \ - felix_vsc9959.o + felix_vsc9959.o \ + seville_vsc9953.o
drivers/net/dsa/ocelot/felix.h +7 -0
@@ -59,4 +59,11 @@ struct felix { resource_size_t imdio_base; }; +void vsc9959_pcs_link_state (struct ocelot *ocelot,int port, +struct phylink_link_state *state); +void vsc9959_pcs_init (struct ocelot *ocelot,int port, +unsigned int link_an_mode, +const struct phylink_link_state *state); +void vsc9959_mdio_bus_free (struct ocelot *ocelot); +#endif
drivers/net/dsa/ocelot/felix_vsc9959.c +6 -6
@@ -963,9 +963,9 @@ static void vsc9959_pcs_init_usxgmii(struct phy_device *pcs, USXGMII_ADVERTISE_FDX); } -static void vsc9959_pcs_init (struct ocelot *ocelot,int port, -unsigned int link_an_mode, -const struct phylink_link_state *state) +void vsc9959_pcs_init (struct ocelot *ocelot,int port, +unsigned int link_an_mode, +const struct phylink_link_state *state) {struct felix *felix =ocelot_to_felix (ocelot);struct phy_device *pcs = felix->pcs[port];
@@ -1113,8 +1113,8 @@ static void vsc9959_pcs_link_state_usxgmii(struct phy_device *pcs, pcs->duplex =DUPLEX_HALF ; } -static void vsc9959_pcs_link_state (struct ocelot *ocelot,int port, -struct phylink_link_state *state) +void vsc9959_pcs_link_state (struct ocelot *ocelot,int port, +struct phylink_link_state *state) {struct felix *felix =ocelot_to_felix (ocelot);struct phy_device *pcs = felix->pcs[port];
@@ -1303,7 +1303,7 @@ static int vsc9959_mdio_bus_alloc(struct ocelot *ocelot)return 0 ; } -static void vsc9959_mdio_bus_free (struct ocelot *ocelot) +void vsc9959_mdio_bus_free (struct ocelot *ocelot) {struct felix *felix =ocelot_to_felix (ocelot);int port;
drivers/net/dsa/ocelot/seville_vsc9953.c new file +1111 -0
1,111 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH v2 net-next 13/13] net: dsa: felix: introduce support for Seville VSC9953 switch
Quoted 20 lines · Vladimir Oltean
From: Maxim Kochetkov <[email protected]>
This is another switch from Vitesse / Microsemi / Microchip, that has 10 port (8 external, 2 internal) and is integrated into the Freescale / NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A, except that this is a platform device and Felix is a PCI device, and it doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus using a
phy_deviceabstraction for it (yes, it will be refactored to use a rawmdio_device, like other phylink drivers do, but let's keep it like that for now). But unlike Felix, the MDIO bus and the PCS are not from the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it is actually an instantiation ofdrivers/net/phy/mdio-mscc-miim.c. But it would be difficult to reuse that driver (it doesn't even use regmap, and it's less than 200 lines of code), so we hand-roll here some internal MDIO bus accessors withinseville_vsc9953.c, which serves the purpose of driving the PCS absolutely fine.
Quoted 6 lines
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of SerDes protocol, so we need to do pre-validation of PHY mode from device tree and not let phylink change it.
Signed-off-by Maxim Kochetkov <[email protected]>Signed-off-by Vladimir Oltean <[email protected]>
Signature · 1 line
Florian
David Miller
maintainerFrom: Vladimir Oltean <[email protected]>
Date: Sat, 30 May 2020 14:51:29 +0300
Quoted 11 lines
From: Vladimir Oltean <[email protected]>
Looking at the Felix and Ocelot drivers, Maxim asked if it would be possible to use them as a base for a new driver for the Seville switch inside NXP T1040. Turns out, it is! The result is that the
mscc_felixdriver was extended to probe on Seville.The biggest challenge seems to be getting register read/write API generic enough to cover such wild bitfield variations between hardware generations.
Quoted 5 lines
There is a trivial dependency patch on the regmap core which is in Mark Brown's for-next tree:
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap.git/commit/?h=for-next&id=8baebfc2aca26e3fa67ab28343671b82be42b22c
I didn't know what to do with it, so I just added it here as well, as 01/13, so that net-next builds wouldn't break.
Looks good, series applied, thanks.
David Miller
maintainerFrom: David Miller <[email protected]>
Date: Sat, 30 May 2020 18:03:51 -0700 (PDT)
Quoted 1 line
Looks good, series applied, thanks.
Actually, reverted, this doesn't build:
[davem@localhost net-next]$ make -s -j14
ld: drivers/net/dsa/ocelot/seville_vsc9953.o: in function `seville_driver_init':
seville_vsc9953.c:(.init.text+0x0): multiple definition of `init_module'; drivers/net/dsa/ocelot/felix_vsc9959.o:felix_vsc9959.c:(.init.text+0x0): first defined here
ld: drivers/net/dsa/ocelot/seville_vsc9953.o: in function `seville_driver_exit':
seville_vsc9953.c:(.exit.text+0x0): multiple definition of `cleanup_module'; drivers/net/dsa/ocelot/felix_vsc9959.o:felix_vsc9959.c:(.exit.text+0x0): first defined here make[4]: *** [scripts/Makefile.build:422: drivers/net/dsa/ocelot/mscc_felix.o] Error 1
make[3]: *** [scripts/Makefile.build:488: drivers/net/dsa/ocelot] Error 2
make[2]: *** [scripts/Makefile.build:488: drivers/net/dsa] Error 2