drm/xe: Add Xe3p support
cover drm/xe: Add Xe3p support
This begins the support for the Xe3p arch - it contains generic support for graphics version 35 and the Xe3p_xpc IP, the Xe3p_LPM IP for media and support for Nova Lake S (NVL-S), that uses a mix of IPs - the display side for NVL-S will be submitted separately.
---
Balasubramani Vivekanandan (4):
drm/xe/xe3p_lpm: Add special check in Media GT for Main GAMCTRL drm/xe/xe3p_lpm: Stop reading the CTC_MODE register drm/xe/xe3p_lpm: Skip disabling NOA on unsupported IPs drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
Brian Welty (1):
drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
Dnyaneshwar Bhadane (1):
drm/xe/nvls: Attach MOCS table for NVL-S
Fei Yang (1):
drm/xe/xe3p_xpc: Add L3 bank mask
Harish Chegondi (1):
drm/xe/xe3p: Add xe3p EU stall data format
Matt Roper (8):
drm/xe/xe3p_lpm: Handle MCR steering
drm/xe/xe3p: Stop programming RCU_MODE's fixed slice mode setting drm/xe/xe3p: Determine service copy availability from fuse drm/xe/nvl: Define NVL-S platform
drm/xe/nvls: Define GuC firmware for NVL-S drm/xe/xe3p_xpc: Add MCR steering
drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs drm/xe/xe3p_xpc: Setup PAT table
S A Muqthyar Ahmed (1):
drm/xe/xe3p_xpc: Add support for compute walker for non-MSIx
Shekhar Chauhan (2):
drm/xe/xe3: Add support for graphics IP versions 30.04 & 30.05 drm/xe/xe3p_lpm: Add support for media IP versions 35.00 & 35.03
Tejas Upadhyay (3):
drm/xe/xe3p: Skip TD flush
drm/xe/xe3p: Enable L2 flush optimization feature drm/xe/xe3p: Flush userptr/shrinker bo cachelines manually
Wang Xin (1):
drm/xe: Dump CURRENT_LRCA and CSMQDEBUG registers
drivers/gpu/drm/xe/regs/xe_engine_regs.h | 5 ++ drivers/gpu/drm/xe/regs/xe_gt_regs.h | 12 ++++ drivers/gpu/drm/xe/regs/xe_irq_regs.h | 1 + drivers/gpu/drm/xe/xe_bo.c | 3 +- drivers/gpu/drm/xe/xe_device.c | 28 ++++++++++ drivers/gpu/drm/xe/xe_device.h | 1 + drivers/gpu/drm/xe/xe_eu_stall.c | 23 ++++++++ drivers/gpu/drm/xe/xe_gt.h | 6 ++ drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++ drivers/gpu/drm/xe/xe_gt_mcr.c | 61 ++++++++++++++++++-- drivers/gpu/drm/xe/xe_gt_topology.c | 6 +- drivers/gpu/drm/xe/xe_gt_types.h | 15 +++++ drivers/gpu/drm/xe/xe_guc.c | 49 ++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +- drivers/gpu/drm/xe/xe_guc_capture.c | 53 +++++++++++++++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 2 + drivers/gpu/drm/xe/xe_hw_engine.c | 50 ++++++++++++++--- drivers/gpu/drm/xe/xe_irq.c | 4 ++ drivers/gpu/drm/xe/xe_mocs.c | 1 + drivers/gpu/drm/xe/xe_oa.c | 3 +- drivers/gpu/drm/xe/xe_pat.c | 96 +++++++++++++++++++++++++++++++- drivers/gpu/drm/xe/xe_pci.c | 23 ++++++++ drivers/gpu/drm/xe/xe_platform_types.h | 1 + drivers/gpu/drm/xe/xe_rtp.c | 6 ++ drivers/gpu/drm/xe/xe_rtp.h | 10 ++++ drivers/gpu/drm/xe/xe_tuning.c | 9 ++- drivers/gpu/drm/xe/xe_uc_fw.c | 1 + drivers/gpu/drm/xe/xe_userptr.c | 3 +- drivers/gpu/drm/xe/xe_wa.c | 6 +- drivers/gpu/drm/xe/xe_wa_oob.rules | 7 ++- include/drm/intel/pciids.h | 9 +++ 32 files changed, 477 insertions(+), 28 deletions(-)
base-commit: c917f7d11493984be9f381ca0a7667bd3e587ada
change-id: 20251013-xe3p-81bb749e9de0
Lucas De Marchi
PATCH 1/23 drm/xe/xe3: Add support for graphics IP versions 30.04 & 30.05
From: Shekhar Chauhan <[email protected]>
Add graphics IP versions 30.04 & 30.05 and initial workarounds for these IP versions.
BSpec: 74201
--- drivers/gpu/drm/xe/xe_pci.c | 2 ++ drivers/gpu/drm/xe/xe_wa.c | 6 +++--- drivers/gpu/drm/xe/xe_wa_oob.rules | 7 +++++-- 3 files changed, 10 insertions(+), 5 deletions(-)
drivers/gpu/drm/xe/xe_pci.c +2 -0
@@ -149,6 +149,8 @@ static const struct xe_ip graphics_ips[] = { { 3000, "Xe3_LPG", &graphics_xe2 }, { 3001, "Xe3_LPG", &graphics_xe2 }, { 3003, "Xe3_LPG", &graphics_xe2 }, + { 3004, "Xe3_LPG", &graphics_xe2 }, + { 3005, "Xe3_LPG", &graphics_xe2 }, };/* Pre-GMDID Media IPs */
drivers/gpu/drm/xe/xe_wa.c +3 -3
@@ -684,7 +684,7 @@ static const struct xe_rtp_entry_sr engine_was[] = { }, {XE_RTP_NAME ("13012615864" ),XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3001 ),OR , -GRAPHICS_VERSION (3003 ), +GRAPHICS_VERSION_RANGE (3003 ,3005 ),FUNC (xe_rtp_match_first_render_or_compute)),XE_RTP_ACTIONS (SET (TDL_TSL_CHICKEN ,RES_CHK_SPR_DIS )) },
@@ -695,7 +695,7 @@ static const struct xe_rtp_entry_sr engine_was[] = { XE_RTP_ACTION_FLAG(ENGINE_BASE))) }, {XE_RTP_NAME ("14021402888" ), -XE_RTP_RULES (GRAPHICS_VERSION (3003 ),FUNC (xe_rtp_match_first_render_or_compute)), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3003 ,3005 ),FUNC (xe_rtp_match_first_render_or_compute)),XE_RTP_ACTIONS (SET (HALF_SLICE_CHICKEN7 ,CLEAR_OPTIMIZATION_DISABLE )) }, { XE_RTP_NAME("18041344222"),
@@ -913,7 +913,7 @@ static const struct xe_rtp_entry_sr lrc_was[] = { DIS_AUTOSTRIP)) }, {XE_RTP_NAME ("22021007897" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3003 ),ENGINE_CLASS (RENDER )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3005 ),ENGINE_CLASS (RENDER )),XE_RTP_ACTIONS (SET (COMMON_SLICE_CHICKEN4 ,SBE_PUSH_CONSTANT_BEHIND_FIX_ENABLE )) }, };
drivers/gpu/drm/xe/xe_wa_oob.rules +5 -2
@@ -34,14 +34,17 @@ 13011645652 GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 14022293748 GRAPHICS_VERSION_RANGE(2001, 2002) GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 22019794406 GRAPHICS_VERSION_RANGE(2001, 2002) GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 22019338487 MEDIA_VERSION(2000) GRAPHICS_VERSION(2001), FUNC(xe_rtp_match_not_sriov_vf) MEDIA_VERSION(3000), MEDIA_STEP(A0, B0), FUNC(xe_rtp_match_not_sriov_vf)
@@ -63,11 +66,11 @@ 16023105232 GRAPHICS_VERSION_RANGE(2001, 3001) MEDIA_VERSION_RANGE(1301, 3000) MEDIA_VERSION(3002) - GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3003, 3005) 16026508708 GRAPHICS_VERSION_RANGE(1200, 3001) MEDIA_VERSION_RANGE(1300, 3000) MEDIA_VERSION(3002) - GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3003, 3005) 14020001231 GRAPHICS_VERSION_RANGE(2001,2004), FUNC(xe_rtp_match_psmi_enabled) MEDIA_VERSION(2000), FUNC(xe_rtp_match_psmi_enabled) MEDIA_VERSION(3000), FUNC(xe_rtp_match_psmi_enabled)
Signature · 1 line
2.51.0
Re: [PATCH 01/23] drm/xe/xe3: Add support for graphics IP versions 30.04 & 30.05
Quoted 64 lines · Lucas De Marchi
From: Shekhar Chauhan <[email protected]>
Add graphics IP versions 30.04 & 30.05 and initial workarounds for these IP versions.
BSpec: 74201
Cc Sai Teja Pottumuttu <[email protected]>Signed-off-by Shekhar Chauhan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pci.c | 2 ++ drivers/gpu/drm/xe/xe_wa.c | 6 +++--- drivers/gpu/drm/xe/xe_wa_oob.rules | 7 +++++-- 3 files changed, 10 insertions(+), 5 deletions(-)drivers/gpu/drm/xe/xe_pci.c +2
-0@@ -149,6 +149,8 @@ static const struct xe_ip graphics_ips[] = { { 3000, "Xe3_LPG", &graphics_xe2 }, { 3001, "Xe3_LPG", &graphics_xe2 }, { 3003, "Xe3_LPG", &graphics_xe2 }, + { 3004, "Xe3_LPG", &graphics_xe2 }, + { 3005, "Xe3_LPG", &graphics_xe2 }, };/* Pre-GMDID Media IPs */ drivers/gpu/drm/xe/xe_wa.c +3
-3@@ -684,7 +684,7 @@ static const struct xe_rtp_entry_sr engine_was[] = { }, {XE_RTP_NAME ("13012615864" ),XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3001 ),OR , -GRAPHICS_VERSION (3003 ), +GRAPHICS_VERSION_RANGE (3003 ,3005 ),FUNC (xe_rtp_match_first_render_or_compute)),XE_RTP_ACTIONS (SET (TDL_TSL_CHICKEN ,RES_CHK_SPR_DIS )) },@@ -695,7 +695,7 @@ static const struct xe_rtp_entry_sr engine_was[] = { XE_RTP_ACTION_FLAG(ENGINE_BASE))) }, {XE_RTP_NAME ("14021402888" ), -XE_RTP_RULES (GRAPHICS_VERSION (3003 ),FUNC (xe_rtp_match_first_render_or_compute)), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3003 ,3005 ),FUNC (xe_rtp_match_first_render_or_compute)),XE_RTP_ACTIONS (SET (HALF_SLICE_CHICKEN7 ,CLEAR_OPTIMIZATION_DISABLE )) }, { XE_RTP_NAME("18041344222"),@@ -913,7 +913,7 @@ static const struct xe_rtp_entry_sr lrc_was[] = { DIS_AUTOSTRIP)) }, {XE_RTP_NAME ("22021007897" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3003 ),ENGINE_CLASS (RENDER )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3005 ),ENGINE_CLASS (RENDER )),XE_RTP_ACTIONS (SET (COMMON_SLICE_CHICKEN4 ,SBE_PUSH_CONSTANT_BEHIND_FIX_ENABLE )) }, };drivers/gpu/drm/xe/xe_wa_oob.rules +0
-0
drivers/gpu/drm/xe/xe_wa_oob.rules line 38
Quoted 5 lines
drivers/gpu/drm/xe/xe_wa_oob.rules +1
-0@@ -34,14 +34,17 @@ 13011645652 GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 14022293748 GRAPHICS_VERSION_RANGE(2001, 2002)
Any specific reason for keeping 3003 different from the range of (3004, 3005)? Can we have a single range from (3003, 3005)? Same for the two additions below.
Other than this, there are a couple of new workarounds which are introduced for these IPs, but maybe we can add them once the initial upstreaming is finished, nothing major.
Apart from these two comments, LGTM, and,
Quoted 27 lines
drivers/gpu/drm/xe/xe_wa_oob.rules +4
-2GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 22019794406 GRAPHICS_VERSION_RANGE(2001, 2002) GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 22019338487 MEDIA_VERSION(2000) GRAPHICS_VERSION(2001), FUNC(xe_rtp_match_not_sriov_vf) MEDIA_VERSION(3000), MEDIA_STEP(A0, B0), FUNC(xe_rtp_match_not_sriov_vf)@@ -63,11 +66,11 @@ 16023105232 GRAPHICS_VERSION_RANGE(2001, 3001) MEDIA_VERSION_RANGE(1301, 3000) MEDIA_VERSION(3002) - GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3003, 3005) 16026508708 GRAPHICS_VERSION_RANGE(1200, 3001) MEDIA_VERSION_RANGE(1300, 3000) MEDIA_VERSION(3002) - GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3003, 3005) 14020001231 GRAPHICS_VERSION_RANGE(2001,2004), FUNC(xe_rtp_match_psmi_enabled) MEDIA_VERSION(2000), FUNC(xe_rtp_match_psmi_enabled) MEDIA_VERSION(3000), FUNC(xe_rtp_match_psmi_enabled)
Re: [PATCH 01/23] drm/xe/xe3: Add support for graphics IP versions 30.04 & 30.05
In reply to Lucas De MarchiQuoted 64 lines · Lucas De Marchi
From: Shekhar Chauhan <[email protected]>
Add graphics IP versions 30.04 & 30.05 and initial workarounds for these IP versions.
BSpec: 74201
Cc Sai Teja Pottumuttu <[email protected]>Signed-off-by Shekhar Chauhan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pci.c | 2 ++ drivers/gpu/drm/xe/xe_wa.c | 6 +++--- drivers/gpu/drm/xe/xe_wa_oob.rules | 7 +++++-- 3 files changed, 10 insertions(+), 5 deletions(-)drivers/gpu/drm/xe/xe_pci.c +2
-0@@ -149,6 +149,8 @@ static const struct xe_ip graphics_ips[] = { { 3000, "Xe3_LPG", &graphics_xe2 }, { 3001, "Xe3_LPG", &graphics_xe2 }, { 3003, "Xe3_LPG", &graphics_xe2 }, + { 3004, "Xe3_LPG", &graphics_xe2 }, + { 3005, "Xe3_LPG", &graphics_xe2 }, };/* Pre-GMDID Media IPs */ drivers/gpu/drm/xe/xe_wa.c +3
-3@@ -684,7 +684,7 @@ static const struct xe_rtp_entry_sr engine_was[] = { }, {XE_RTP_NAME ("13012615864" ),XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3001 ),OR , -GRAPHICS_VERSION (3003 ), +GRAPHICS_VERSION_RANGE (3003 ,3005 ),FUNC (xe_rtp_match_first_render_or_compute)),XE_RTP_ACTIONS (SET (TDL_TSL_CHICKEN ,RES_CHK_SPR_DIS )) },@@ -695,7 +695,7 @@ static const struct xe_rtp_entry_sr engine_was[] = { XE_RTP_ACTION_FLAG(ENGINE_BASE))) }, {XE_RTP_NAME ("14021402888" ), -XE_RTP_RULES (GRAPHICS_VERSION (3003 ),FUNC (xe_rtp_match_first_render_or_compute)), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3003 ,3005 ),FUNC (xe_rtp_match_first_render_or_compute)),XE_RTP_ACTIONS (SET (HALF_SLICE_CHICKEN7 ,CLEAR_OPTIMIZATION_DISABLE )) }, { XE_RTP_NAME("18041344222"),@@ -913,7 +913,7 @@ static const struct xe_rtp_entry_sr lrc_was[] = { DIS_AUTOSTRIP)) }, {XE_RTP_NAME ("22021007897" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3003 ),ENGINE_CLASS (RENDER )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (3000 ,3005 ),ENGINE_CLASS (RENDER )),XE_RTP_ACTIONS (SET (COMMON_SLICE_CHICKEN4 ,SBE_PUSH_CONSTANT_BEHIND_FIX_ENABLE )) }, };drivers/gpu/drm/xe/xe_wa_oob.rules +0
-0
drivers/gpu/drm/xe/xe_wa_oob.rules line 37
Quoted 4 lines
drivers/gpu/drm/xe/xe_wa_oob.rules +1
-0@@ -34,14 +34,17 @@ 13011645652 GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005)
As Shekhar pointed out, 30.04/30.05 can be combined with the 30.03 line for all of these.
Otherwise,
Quoted 31 lines
drivers/gpu/drm/xe/xe_wa_oob.rules +4
-214022293748 GRAPHICS_VERSION_RANGE(2001, 2002) GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 22019794406 GRAPHICS_VERSION_RANGE(2001, 2002) GRAPHICS_VERSION(2004) GRAPHICS_VERSION_RANGE(3000, 3001) GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3004, 3005) 22019338487 MEDIA_VERSION(2000) GRAPHICS_VERSION(2001), FUNC(xe_rtp_match_not_sriov_vf) MEDIA_VERSION(3000), MEDIA_STEP(A0, B0), FUNC(xe_rtp_match_not_sriov_vf)@@ -63,11 +66,11 @@ 16023105232 GRAPHICS_VERSION_RANGE(2001, 3001) MEDIA_VERSION_RANGE(1301, 3000) MEDIA_VERSION(3002) - GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3003, 3005) 16026508708 GRAPHICS_VERSION_RANGE(1200, 3001) MEDIA_VERSION_RANGE(1300, 3000) MEDIA_VERSION(3002) - GRAPHICS_VERSION(3003) + GRAPHICS_VERSION_RANGE(3003, 3005) 14020001231 GRAPHICS_VERSION_RANGE(2001,2004), FUNC(xe_rtp_match_psmi_enabled) MEDIA_VERSION(2000), FUNC(xe_rtp_match_psmi_enabled) MEDIA_VERSION(3000), FUNC(xe_rtp_match_psmi_enabled)Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 2/23 drm/xe/xe3p_lpm: Add support for media IP versions 35.00 & 35.03
In reply to Lucas De MarchiFrom: Shekhar Chauhan <[email protected]>
Xe3p_LPM is very similar to Xe3_LPM on the kmd interface, so it can use the same descriptor structure. Add both 35.00 and 35.03 IP versions.
BSpec: 74201, 74202, 77977
--- drivers/gpu/drm/xe/xe_pci.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/gpu/drm/xe/xe_pci.c +2 -0
@@ -164,6 +164,8 @@ static const struct xe_ip media_ips[] = { { 2000, "Xe2_LPM", &media_xelpmp }, { 3000, "Xe3_LPM", &media_xelpmp }, { 3002, "Xe3_LPM", &media_xelpmp }, + { 3500, "Xe3p_LPM", &media_xelpmp }, + { 3503, "Xe3p_LPM", &media_xelpmp }, }; static const struct xe_device_desc tgl_desc = {
Signature · 1 line
2.51.0
Re: [PATCH 02/23] drm/xe/xe3p_lpm: Add support for media IP versions 35.00 & 35.03
Quoted 9 lines · Lucas De Marchi
From: Shekhar Chauhan <[email protected]>
Xe3p_LPMis very similar toXe3_LPMon the kmd interface, so it can use the same descriptor structure. Add both 35.00 and 35.03 IP versions.BSpec: 74201, 74202, 77977
Cc Balasubramani Vivekanandan <[email protected]>Signed-off-by Shekhar Chauhan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
LGTM,
Quoted 18 lines
--- drivers/gpu/drm/xe/xe_pci.c | 2 ++ 1 file changed, 2 insertions(+)drivers/gpu/drm/xe/xe_pci.c +2
-0@@ -164,6 +164,8 @@ static const struct xe_ip media_ips[] = { { 2000, "Xe2_LPM", &media_xelpmp }, { 3000, "Xe3_LPM", &media_xelpmp }, { 3002, "Xe3_LPM", &media_xelpmp }, + { 3500, "Xe3p_LPM", &media_xelpmp }, + { 3503, "Xe3p_LPM", &media_xelpmp }, }; static const struct xe_device_desc tgl_desc = {
Re: [PATCH 02/23] drm/xe/xe3p_lpm: Add support for media IP versions 35.00 & 35.03
In reply to Lucas De MarchiQuoted 6 lines · Lucas De Marchi
From: Shekhar Chauhan <[email protected]>
Xe3p_LPMis very similar toXe3_LPMon the kmd interface, so it can use the same descriptor structure. Add both 35.00 and 35.03 IP versions.BSpec: 74201, 74202, 77977
Should page 77979 also be included in this list since that's where the 35.03 number is actually documented?
Otherwise,
Quoted 24 lines
Cc Balasubramani Vivekanandan <[email protected]>Signed-off-by Shekhar Chauhan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pci.c | 2 ++ 1 file changed, 2 insertions(+)drivers/gpu/drm/xe/xe_pci.c +2
-0@@ -164,6 +164,8 @@ static const struct xe_ip media_ips[] = { { 2000, "Xe2_LPM", &media_xelpmp }, { 3000, "Xe3_LPM", &media_xelpmp }, { 3002, "Xe3_LPM", &media_xelpmp }, + { 3500, "Xe3p_LPM", &media_xelpmp }, + { 3503, "Xe3p_LPM", &media_xelpmp }, }; static const struct xe_device_desc tgl_desc = {Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 3/23 drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
In reply to Lucas De MarchiFrom: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag, GUC_CTL_MAIN_GAMCTRL_QUEUES to convey this decision. A new helper function, xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.
The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the MAIN_GAMCTRL queues.
--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)
drivers/gpu/drm/xe/regs/xe_gt_regs.h +3 -0
@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)
drivers/gpu/drm/xe/xe_gt.h +6 -0
@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {
drivers/gpu/drm/xe/xe_guc.c +27 -0
@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }
@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }
@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of +* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc); + +return GT_VER (gt) >=35 ; +} +#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )#include "tests/xe_guc_g2g_test.c" #endif
drivers/gpu/drm/xe/xe_guc.h +1 -0
@@ -52,6 +52,7 @@ void xe_guc_stop_prepare(struct xe_guc *guc);void xe_guc_stop (struct xe_guc *guc);int xe_guc_start (struct xe_guc *guc);void xe_guc_declare_wedged (struct xe_guc *guc); +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc);#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )int xe_guc_g2g_test_notification (struct xe_guc *guc,u32 *payload,u32 len);
drivers/gpu/drm/xe/xe_guc_ads.c +5 -1
@@ -820,16 +820,20 @@ static void guc_mmio_reg_state_init(struct xe_guc_ads *ads)static void guc_um_init_params (struct xe_guc_ads *ads) {u32 um_queue_offset =guc_ads_um_queues_offset (ads); +struct xe_guc *guc =ads_to_guc (ads);u64 base_dpa;u32 base_ggtt; +bool with_dpa;int i; + with_dpa = !xe_guc_using_main_gamctrl_queues (guc); + base_ggtt =xe_bo_ggtt_addr (ads->bo) + um_queue_offset; base_dpa =xe_bo_main_addr (ads->bo,PAGE_SIZE ) + um_queue_offset;for (i =0 ; i <GUC_UM_HW_QUEUE_MAX ; ++i) {ads_blob_write (ads, um_init_params.queue_params[i].base_dpa, - base_dpa + (i *GUC_UM_QUEUE_SIZE )); + with_dpa ? (base_dpa + (i *GUC_UM_QUEUE_SIZE )) :0 );ads_blob_write (ads, um_init_params.queue_params[i].base_ggtt_address, base_ggtt + (i *GUC_UM_QUEUE_SIZE )); ads_blob_write(ads, um_init_params.queue_params[i].size_in_bytes,
drivers/gpu/drm/xe/xe_guc_fwif.h +1 -0
@@ -113,6 +113,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_SLPC BIT(2)#define GUC_CTL_ENABLE_LITE_RESTORE BIT(4)#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7) +#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14)#define GUC_CTL_DEBUG 3
Signature · 1 line
2.51.0
Re: [PATCH 03/23] drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
Quoted 102 lines · Lucas De Marchi
From: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag,GUC_CTL_MAIN_GAMCTRL_QUEUESto convey this decision. A new helper function,xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the
MAIN_GAMCTRLqueues.Signed-off-by Brian Welty <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)drivers/gpu/drm/xe/xe_gt.h +6
-0@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {drivers/gpu/drm/xe/xe_guc.c +15
-0@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of
drivers/gpu/drm/xe/xe_guc.c void xe_guc_declare_wedged(struct xe_guc *guc) · line 1684
Quoted 10 lines
drivers/gpu/drm/xe/xe_guc.c +10
-0+* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc); + +return GT_VER (gt) >=35 ;
Revisiting the spec on this, I'm not sure whether using GT_VER() here is actually the right thing to do. As far as I can see, the media GT does not actually have a "main gamctrl" register range at all (i.e., bspec 76445 only lists MCR gamctrl ranges, and 0x38EF00-0x38EFFF falls within a reserved/unused block). That means that registers like MAIN_GAMCTRL_MODE that we're trying to write during xe_guc_upload above don't actually exist for the media GT. Furthermore, the tagging on the register detail page 73540 also seems to imply that this only applies to the primary/graphics GT.
Matt
Quoted 59 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+} +#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )#include "tests/xe_guc_g2g_test.c" #endif drivers/gpu/drm/xe/xe_guc.h +1
-0@@ -52,6 +52,7 @@ void xe_guc_stop_prepare(struct xe_guc *guc);void xe_guc_stop (struct xe_guc *guc);int xe_guc_start (struct xe_guc *guc);void xe_guc_declare_wedged (struct xe_guc *guc); +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc);#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )int xe_guc_g2g_test_notification (struct xe_guc *guc,u32 *payload,u32 len);drivers/gpu/drm/xe/xe_guc_ads.c +5
-1@@ -820,16 +820,20 @@ static void guc_mmio_reg_state_init(struct xe_guc_ads *ads)static void guc_um_init_params (struct xe_guc_ads *ads) {u32 um_queue_offset =guc_ads_um_queues_offset (ads); +struct xe_guc *guc =ads_to_guc (ads);u64 base_dpa;u32 base_ggtt; +bool with_dpa;int i; + with_dpa = !xe_guc_using_main_gamctrl_queues (guc); + base_ggtt =xe_bo_ggtt_addr (ads->bo) + um_queue_offset; base_dpa =xe_bo_main_addr (ads->bo,PAGE_SIZE ) + um_queue_offset;for (i =0 ; i <GUC_UM_HW_QUEUE_MAX ; ++i) {ads_blob_write (ads, um_init_params.queue_params[i].base_dpa, - base_dpa + (i *GUC_UM_QUEUE_SIZE )); + with_dpa ? (base_dpa + (i *GUC_UM_QUEUE_SIZE )) :0 );ads_blob_write (ads, um_init_params.queue_params[i].base_ggtt_address, base_ggtt + (i *GUC_UM_QUEUE_SIZE )); ads_blob_write(ads, um_init_params.queue_params[i].size_in_bytes,drivers/gpu/drm/xe/xe_guc_fwif.h +1
-0@@ -113,6 +113,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_SLPC BIT(2)#define GUC_CTL_ENABLE_LITE_RESTORE BIT(4)#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7) +#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14)#define GUC_CTL_DEBUG 3Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 03/23] drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
Quoted 111 lines · Matt Roper
Quoted 110 lines · Lucas De Marchi
From: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag,GUC_CTL_MAIN_GAMCTRL_QUEUESto convey this decision. A new helper function,xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the
MAIN_GAMCTRLqueues.Signed-off-by Brian Welty <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)drivers/gpu/drm/xe/xe_gt.h +6
-0@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {drivers/gpu/drm/xe/xe_guc.c +23
-0@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of +* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc);
Quoted 8 lines
drivers/gpu/drm/xe/xe_guc.c void xe_guc_declare_wedged(struct xe_guc *guc) · line 1684
Quoted 2 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+ +return GT_VER (gt) >=35 ;Revisiting the spec on this, I'm not sure whether using
GT_VER()here is actually the right thing to do. As far as I can see, the media GT does not actually have a "main gamctrl" register range at all (i.e., bspec 76445 only lists MCR gamctrl ranges, and 0x38EF00-0x38EFFF falls within a reserved/unused block). That means that registers like
true
Quoted 1 line
MAIN_GAMCTRL_MODEthat we're trying to write duringxe_guc_uploadabove
We do have MAIN_GAMCTRL_MODE for xe3p_lpm in bspec 73540. The tagging is odd, but there is a reference to the register at 0x38EF00. It wouldn't make sense to have a 0x38xxxx register instance for primary/graphics GT.
So either
1) we don't have it like you said
2) we have it and there's something missing in the MCR ranges
Quoted 3 lines
don't actually exist for the media GT. Furthermore, the tagging on the register detail page 73540 also seems to imply that this only applies to the primary/graphics GT.
so... in that case we'd need to check both the gt type and graphics ver, so we load GuC with those different flags. I will take a shot at that and check if anything breaks.
Bala, since you did the patch following this, do you remember of anything related to this?
Lucas De Marchi
Quoted 69 lines
Matt
Quoted 59 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+} +#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )#include "tests/xe_guc_g2g_test.c" #endif drivers/gpu/drm/xe/xe_guc.h +1
-0@@ -52,6 +52,7 @@ void xe_guc_stop_prepare(struct xe_guc *guc);void xe_guc_stop (struct xe_guc *guc);int xe_guc_start (struct xe_guc *guc);void xe_guc_declare_wedged (struct xe_guc *guc); +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc);#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )int xe_guc_g2g_test_notification (struct xe_guc *guc,u32 *payload,u32 len);drivers/gpu/drm/xe/xe_guc_ads.c +5
-1@@ -820,16 +820,20 @@ static void guc_mmio_reg_state_init(struct xe_guc_ads *ads)static void guc_um_init_params (struct xe_guc_ads *ads) {u32 um_queue_offset =guc_ads_um_queues_offset (ads); +struct xe_guc *guc =ads_to_guc (ads);u64 base_dpa;u32 base_ggtt; +bool with_dpa;int i; + with_dpa = !xe_guc_using_main_gamctrl_queues (guc); + base_ggtt =xe_bo_ggtt_addr (ads->bo) + um_queue_offset; base_dpa =xe_bo_main_addr (ads->bo,PAGE_SIZE ) + um_queue_offset;for (i =0 ; i <GUC_UM_HW_QUEUE_MAX ; ++i) {ads_blob_write (ads, um_init_params.queue_params[i].base_dpa, - base_dpa + (i *GUC_UM_QUEUE_SIZE )); + with_dpa ? (base_dpa + (i *GUC_UM_QUEUE_SIZE )) :0 );ads_blob_write (ads, um_init_params.queue_params[i].base_ggtt_address, base_ggtt + (i *GUC_UM_QUEUE_SIZE )); ads_blob_write(ads, um_init_params.queue_params[i].size_in_bytes,drivers/gpu/drm/xe/xe_guc_fwif.h +1
-1@@ -113,6 +113,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_SLPC BIT(2)#define GUC_CTL_ENABLE_LITE_RESTORE BIT(4)#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7) +#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14)#define GUC_CTL_DEBUG 3 --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 03/23] drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
Quoted 139 lines · Lucas De Marchi
Quoted 111 lines · Matt Roper
Quoted 110 lines · Lucas De Marchi
From: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag,GUC_CTL_MAIN_GAMCTRL_QUEUESto convey this decision. A new helper function,xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the
MAIN_GAMCTRLqueues.Signed-off-by Brian Welty <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)drivers/gpu/drm/xe/xe_gt.h +6
-0@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {drivers/gpu/drm/xe/xe_guc.c +23
-0@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of +* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc);Quoted 8 lines
drivers/gpu/drm/xe/xe_guc.c void xe_guc_declare_wedged(struct xe_guc *guc) · line 1684
Quoted 2 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+ +return GT_VER (gt) >=35 ;Revisiting the spec on this, I'm not sure whether using
GT_VER()here is actually the right thing to do. As far as I can see, the media GT does not actually have a "main gamctrl" register range at all (i.e., bspec 76445 only lists MCR gamctrl ranges, and 0x38EF00-0x38EFFF falls within a reserved/unused block). That means that registers liketrue
Quoted 1 line
MAIN_GAMCTRL_MODEthat we're trying to write duringxe_guc_uploadaboveWe do have
MAIN_GAMCTRL_MODEforxe3p_lpmin bspec 73540. The tagging is odd, but there is a reference to the register at0x38EF00. It wouldn't make sense to have a 0x38xxxx register instance for primary/graphics GT.So either
1) we don't have it like you said
2) we have it and there's something missing in the MCR rangesQuoted 3 lines
don't actually exist for the media GT. Furthermore, the tagging on the register detail page 73540 also seems to imply that this only applies to the primary/graphics GT.
Quoted 6 lines
so... in that case we'd need to check both the gt type and graphics ver, so we load GuC with those different flags. I will take a shot at that and check if anything breaks.
Bala, since you did the patch following this, do you remember of anything related to this?
There seems to be a conflict between the Bspec and the HSD. HSD 16017994409 and the HAS claim the MainGAMCTRL is supported in Xe3p Media IP whereas the Bspec page 73542 and the Steering table show the MainGAMCTRL register range as not available for Xe3p Media.
For me it looks like a Bspec update issue. We have tested and verified the current implementation which enables MainGAMCTRL for Media. I would say lets keep the code as it is though it conflicts with the spec and raise a Bspec issue to get it clarified.
Regards,
Bala
Quoted 72 lines
Lucas De Marchi
Quoted 69 lines
Matt
Quoted 59 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+} +#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )#include "tests/xe_guc_g2g_test.c" #endif drivers/gpu/drm/xe/xe_guc.h +1
-0@@ -52,6 +52,7 @@ void xe_guc_stop_prepare(struct xe_guc *guc);void xe_guc_stop (struct xe_guc *guc);int xe_guc_start (struct xe_guc *guc);void xe_guc_declare_wedged (struct xe_guc *guc); +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc);#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )int xe_guc_g2g_test_notification (struct xe_guc *guc,u32 *payload,u32 len);drivers/gpu/drm/xe/xe_guc_ads.c +5
-1@@ -820,16 +820,20 @@ static void guc_mmio_reg_state_init(struct xe_guc_ads *ads)static void guc_um_init_params (struct xe_guc_ads *ads) {u32 um_queue_offset =guc_ads_um_queues_offset (ads); +struct xe_guc *guc =ads_to_guc (ads);u64 base_dpa;u32 base_ggtt; +bool with_dpa;int i; + with_dpa = !xe_guc_using_main_gamctrl_queues (guc); + base_ggtt =xe_bo_ggtt_addr (ads->bo) + um_queue_offset; base_dpa =xe_bo_main_addr (ads->bo,PAGE_SIZE ) + um_queue_offset;for (i =0 ; i <GUC_UM_HW_QUEUE_MAX ; ++i) {ads_blob_write (ads, um_init_params.queue_params[i].base_dpa, - base_dpa + (i *GUC_UM_QUEUE_SIZE )); + with_dpa ? (base_dpa + (i *GUC_UM_QUEUE_SIZE )) :0 );ads_blob_write (ads, um_init_params.queue_params[i].base_ggtt_address, base_ggtt + (i *GUC_UM_QUEUE_SIZE )); ads_blob_write(ads, um_init_params.queue_params[i].size_in_bytes,drivers/gpu/drm/xe/xe_guc_fwif.h +1
-1@@ -113,6 +113,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_SLPC BIT(2)#define GUC_CTL_ENABLE_LITE_RESTORE BIT(4)#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7) +#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14)#define GUC_CTL_DEBUG 3 --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 03/23] drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
Quoted 152 lines · Balasubramani
Quoted 139 lines · Lucas De Marchi
Quoted 111 lines · Matt Roper
Quoted 110 lines · Lucas De Marchi
From: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag,GUC_CTL_MAIN_GAMCTRL_QUEUESto convey this decision. A new helper function,xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the
MAIN_GAMCTRLqueues.Signed-off-by Brian Welty <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)drivers/gpu/drm/xe/xe_gt.h +6
-0@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {drivers/gpu/drm/xe/xe_guc.c +23
-0@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of +* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc);Quoted 8 lines
drivers/gpu/drm/xe/xe_guc.c void xe_guc_declare_wedged(struct xe_guc *guc) · line 1684
Quoted 2 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+ +return GT_VER (gt) >=35 ;Revisiting the spec on this, I'm not sure whether using
GT_VER()here is actually the right thing to do. As far as I can see, the media GT does not actually have a "main gamctrl" register range at all (i.e., bspec 76445 only lists MCR gamctrl ranges, and 0x38EF00-0x38EFFF falls within a reserved/unused block). That means that registers liketrue
Quoted 1 line
MAIN_GAMCTRL_MODEthat we're trying to write duringxe_guc_uploadaboveWe do have
MAIN_GAMCTRL_MODEforxe3p_lpmin bspec 73540. The tagging is odd, but there is a reference to the register at0x38EF00. It wouldn't make sense to have a 0x38xxxx register instance for primary/graphics GT.So either
1) we don't have it like you said
2) we have it and there's something missing in the MCR rangesQuoted 3 lines
don't actually exist for the media GT. Furthermore, the tagging on the register detail page 73540 also seems to imply that this only applies to the primary/graphics GT.
Quoted 6 lines
so... in that case we'd need to check both the gt type and graphics ver, so we load GuC with those different flags. I will take a shot at that and check if anything breaks.
Bala, since you did the patch following this, do you remember of anything related to this?
There seems to be a conflict between the Bspec and the HSD. HSD 16017994409 and the HAS claim the MainGAMCTRL is supported in Xe3p Media IP whereas the Bspec page 73542 and the Steering table show the MainGAMCTRL register range as not available for Xe3p Media.
Quoted 4 lines
For me it looks like a Bspec update issue. We have tested and verified the current implementation which enables MainGAMCTRL for Media. I would say lets keep the code as it is though it conflicts with the spec and raise a Bspec issue to get it clarified.
I'm circling this back with HW and Spec people. I also did some changes local changes to test. Although since the old queues are still valid, I guess it will just pass, but without this optimization. On the other hand, I'd expect it to not work at all with the current code if it didn't apply to media.
Another point is that we can delay this patch a little bit, since the next patch turns this off for media with the special bits set.
thanks
Lucas De Marchi
Re: [PATCH 03/23] drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
Quoted 158 lines · Lucas De Marchi
Quoted 152 lines · Balasubramani
Quoted 139 lines · Lucas De Marchi
Quoted 111 lines · Matt Roper
Quoted 110 lines · Lucas De Marchi
From: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag,GUC_CTL_MAIN_GAMCTRL_QUEUESto convey this decision. A new helper function,xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the
MAIN_GAMCTRLqueues.Signed-off-by Brian Welty <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)drivers/gpu/drm/xe/xe_gt.h +6
-0@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {drivers/gpu/drm/xe/xe_guc.c +23
-0@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of +* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc);Quoted 8 lines
drivers/gpu/drm/xe/xe_guc.c void xe_guc_declare_wedged(struct xe_guc *guc) · line 1684
Quoted 2 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+ +return GT_VER (gt) >=35 ;Revisiting the spec on this, I'm not sure whether using
GT_VER()here is actually the right thing to do. As far as I can see, the media GT does not actually have a "main gamctrl" register range at all (i.e., bspec 76445 only lists MCR gamctrl ranges, and 0x38EF00-0x38EFFF falls within a reserved/unused block). That means that registers liketrue
Quoted 1 line
MAIN_GAMCTRL_MODEthat we're trying to write duringxe_guc_uploadaboveWe do have
MAIN_GAMCTRL_MODEforxe3p_lpmin bspec 73540. The tagging is odd, but there is a reference to the register at0x38EF00. It wouldn't make sense to have a 0x38xxxx register instance for primary/graphics GT.So either
1) we don't have it like you said
2) we have it and there's something missing in the MCR rangesQuoted 3 lines
don't actually exist for the media GT. Furthermore, the tagging on the register detail page 73540 also seems to imply that this only applies to the primary/graphics GT.
Quoted 6 lines
so... in that case we'd need to check both the gt type and graphics ver, so we load GuC with those different flags. I will take a shot at that and check if anything breaks.
Bala, since you did the patch following this, do you remember of anything related to this?
There seems to be a conflict between the Bspec and the HSD. HSD 16017994409 and the HAS claim the MainGAMCTRL is supported in Xe3p Media IP whereas the Bspec page 73542 and the Steering table show the MainGAMCTRL register range as not available for Xe3p Media.
Quoted 4 lines
For me it looks like a Bspec update issue. We have tested and verified the current implementation which enables MainGAMCTRL for Media. I would say lets keep the code as it is though it conflicts with the spec and raise a Bspec issue to get it clarified.
Quoted 5 lines
I'm circling this back with HW and Spec people. I also did some changes local changes to test. Although since the old queues are still valid, I guess it will just pass, but without this optimization. On the other hand, I'd expect it to not work at all with the current code if it didn't apply to media.
There is an Bspec update to the steering table yesterday which now lists the address range 0x38EF00 - 0x38EFFF as non-MCR. But still the Bspec filtering is not correct. So the register range doesn't show up when filtered for Xe3p Media.
Regards,
Bala
Quoted 6 lines
Another point is that we can delay this patch a little bit, since the next patch turns this off for media with the special bits set.
thanks
Lucas De Marchi
Re: [PATCH 03/23] drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT
In reply to Lucas De MarchiQuoted 121 lines · Lucas De Marchi
Quoted 111 lines · Matt Roper
Quoted 110 lines · Lucas De Marchi
From: Brian Welty <[email protected]>
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a new unicast copy known as "main_gamctrl." The Xe driver doesn't use these registers directly, but we need to instruct the GuC on which set it should use. Since the new, unicast registers are preferred (since they avoid the need for unnecessary MCR synchronization), set a new GuC feature flag,GUC_CTL_MAIN_GAMCTRL_QUEUESto convey this decision. A new helper function,xe_guc_using_main_gamctrl_queues(), is added for use in the 3 independent places that need to handle configuration of the new reporting queues.The mmio write to enable the main gamctl is only done during the general GuC upload. The gamctrl registers are not accessed by the GuC during hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a DPA and GGTT offset. The GuC documentation states that DPA is now MBZ when using the
MAIN_GAMCTRLqueues.Signed-off-by Brian Welty <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_gt.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 27 +++++++++++++++++++++++++++ drivers/gpu/drm/xe/xe_guc.h | 1 + drivers/gpu/drm/xe/xe_guc_ads.c | 6 +++++- drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 6 files changed, 43 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -545,6 +545,9 @@#define SARB_CHICKEN1 XE_REG_MCR(0xe90c)#define COMP_CKN_IN REG_GENMASK(30, 29) +#define MAIN_GAMCTRL_MODE XE_REG(0xef00) +#define MAIN_GAMCTRL_QUEUE_SELECT REG_BIT(0) +#define RCU_MODE XE_REG(0x14800, XE_REG_OPTION_MASKED)#define RCU_MODE_FIXED_SLICE_CCS_MODE REG_BIT(1)#define RCU_MODE_CCS_ENABLE REG_BIT(0)drivers/gpu/drm/xe/xe_gt.h +6
-0@@ -22,6 +22,12 @@#define CCS_MASK (gt) (((gt)->info.engine_mask & XE_HW_ENGINE_CCS_MASK) >> XE_HW_ENGINE_CCS0) +#define GT_VER (gt) ({ \ + typeof(gt) gt_ = (gt); \ + struct xe_device *xe = gt_to_xe(gt_); \ + xe_gt_is_media_type(gt_) ? MEDIA_VER(xe) : GRAPHICS_VER(xe); \ +}) +extern struct fault_attr gt_reset_failure;static inline bool xe_fault_inject_gt_reset (void ) {drivers/gpu/drm/xe/xe_guc.c +23
-0@@ -91,6 +91,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_configfs_get_psmi_enabled (to_pci_dev (xe->drm.dev))) flags |=GUC_CTL_ENABLE_PSMI_LOGGING ; +if (xe_guc_using_main_gamctrl_queues (guc)) + flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +return flags; }@@ -1255,8 +1258,13 @@ int xe_guc_min_load_for_hwconfig(struct xe_guc *guc)int xe_guc_upload (struct xe_guc *guc) { +struct xe_gt *gt =guc_to_gt (guc); +xe_guc_ads_populate (&guc->ads); +if (xe_guc_using_main_gamctrl_queues (guc)) +xe_mmio_write32 (>->mmio,MAIN_GAMCTRL_MODE ,MAIN_GAMCTRL_QUEUE_SELECT ); +return __xe_guc_upload (guc); }@@ -1657,6 +1665,25 @@ void xe_guc_declare_wedged(struct xe_guc *guc)xe_guc_submit_wedge (guc); } +/** +* xe_guc_using_main_gamctrl_queues() - Detect which reporting queues to use. +* @guc: The GuC object +* +* For Xe3p and beyond, we want to program the hardware to use the +* "Main GAMCTRL queue" rather than the legacy queue before we upload +* the GuC firmware. This will allow the GuC to use a new set of +* registers for pagefault handling and avoid some unnecessary +* complications with MCR register range handling. +* +* Return: true if can use new main gamctrl queues. +*/ +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc) +{ +struct xe_gt *gt =guc_to_gt (guc);Quoted 8 lines
drivers/gpu/drm/xe/xe_guc.c void xe_guc_declare_wedged(struct xe_guc *guc) · line 1684
Quoted 2 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+ +return GT_VER (gt) >=35 ;Revisiting the spec on this, I'm not sure whether using
GT_VER()here is actually the right thing to do. As far as I can see, the media GT does not actually have a "main gamctrl" register range at all (i.e., bspec 76445 only lists MCR gamctrl ranges, and 0x38EF00-0x38EFFF falls within a reserved/unused block). That means that registers like
Quoted 8 lines
true
Quoted 1 line
MAIN_GAMCTRL_MODEthat we're trying to write duringxe_guc_uploadaboveWe do have
MAIN_GAMCTRL_MODEforxe3p_lpmin bspec 73540. The tagging is odd, but there is a reference to the register at0x38EF00. It wouldn't make sense to have a 0x38xxxx register instance for primary/graphics GT.
I think this is an artifact of how the bspec's web interface is being strained beyond its original design considerations. 0x38xxxx copies of GT registers get listed somewhat automatically, but on platforms where they've split things into separate "die" designators, the 0x38xxxx register should be ignored if it _only_ applies to the "graphics" die and isn't also tagged as existing on the die that actually holds the media IP. That's the case here since the media die doesn't show up in the list of "platforms."
This is unfortunately very non-obvious and confusing. :-(
Matt
Quoted 88 lines
So either
1) we don't have it like you said
2) we have it and there's something missing in the MCR rangeQuoted 3 lines
don't actually exist for the media GT. Furthermore, the tagging on the register detail page 73540 also seems to imply that this only applies to the primary/graphics GT.
so... in that case we'd need to check both the gt type and graphics ver, so we load GuC with those different flags. I will take a shot at that and check if anything breaks.
Bala, since you did the patch following this, do you remember of anything related to this?
Lucas De Marchi
Quoted 69 lines
Matt
Quoted 59 lines
drivers/gpu/drm/xe/xe_guc.c +2
-0+} +#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )#include "tests/xe_guc_g2g_test.c" #endif drivers/gpu/drm/xe/xe_guc.h +1
-0@@ -52,6 +52,7 @@ void xe_guc_stop_prepare(struct xe_guc *guc);void xe_guc_stop (struct xe_guc *guc);int xe_guc_start (struct xe_guc *guc);void xe_guc_declare_wedged (struct xe_guc *guc); +bool xe_guc_using_main_gamctrl_queues (struct xe_guc *guc);#if IS_ENABLED (CONFIG_DRM_XE_KUNIT_TEST )int xe_guc_g2g_test_notification (struct xe_guc *guc,u32 *payload,u32 len);drivers/gpu/drm/xe/xe_guc_ads.c +5
-1@@ -820,16 +820,20 @@ static void guc_mmio_reg_state_init(struct xe_guc_ads *ads)static void guc_um_init_params (struct xe_guc_ads *ads) {u32 um_queue_offset =guc_ads_um_queues_offset (ads); +struct xe_guc *guc =ads_to_guc (ads);u64 base_dpa;u32 base_ggtt; +bool with_dpa;int i; + with_dpa = !xe_guc_using_main_gamctrl_queues (guc); + base_ggtt =xe_bo_ggtt_addr (ads->bo) + um_queue_offset; base_dpa =xe_bo_main_addr (ads->bo,PAGE_SIZE ) + um_queue_offset;for (i =0 ; i <GUC_UM_HW_QUEUE_MAX ; ++i) {ads_blob_write (ads, um_init_params.queue_params[i].base_dpa, - base_dpa + (i *GUC_UM_QUEUE_SIZE )); + with_dpa ? (base_dpa + (i *GUC_UM_QUEUE_SIZE )) :0 );ads_blob_write (ads, um_init_params.queue_params[i].base_ggtt_address, base_ggtt + (i *GUC_UM_QUEUE_SIZE )); ads_blob_write(ads, um_init_params.queue_params[i].size_in_bytes,drivers/gpu/drm/xe/xe_guc_fwif.h +1
-1@@ -113,6 +113,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_SLPC BIT(2)#define GUC_CTL_ENABLE_LITE_RESTORE BIT(4)#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7) +#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14)#define GUC_CTL_DEBUG 3 --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 4/23 drm/xe/xe3p_lpm: Add special check in Media GT for Main GAMCTRL
In reply to Lucas De MarchiFrom: Balasubramani Vivekanandan <[email protected]>
For Xe3p arch some subunits of an IP may be different. The GMD_ID register returns the Xe3p arch and dedicates the reserved field to mark possible subunit differences. Generally this is an under-the-hood implementation detail that drivers don't need to worry about, but the new Main_GAMCTRL may be enabled or not depending on those.
Those reserved bits are described for Xe3p as: "If Zero, No special case to be handled. If Non-Zero, special case to be handled by Software agent.". That special case is defined per Arch. So if media version is 35, also check the additional reserved bits. To avoid confusion with the usual meaning of "reserved", define them as GMD_ID_SUBIP_FLAG_MASK.
Bspec: 74201
--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 19 +++++++++++++++++++ 2 files changed, 25 insertions(+)
drivers/gpu/drm/xe/regs/xe_gt_regs.h +6 -0
@@ -37,6 +37,12 @@#define GMD_ID XE_REG(0xd8c)#define GMD_ID_ARCH_MASK REG_GENMASK(31, 22)#define GMD_ID_RELEASE_MASK REG_GENMASK(21, 14) +/* +* Spec defines these bits as "Reserved", but then make them assume some +* meaning that depends on the ARCH. To avoid any confusion, call them +* SUBIP_FLAG_MASK. +*/ +#define GMD_ID_SUBIP_FLAG_MASK REG_GENMASK(13, 6)#define GMD_ID_REVID REG_GENMASK(5, 0)#define FORCEWAKE_ACK_GSC XE_REG(0xdf8)
drivers/gpu/drm/xe/xe_guc.c +19 -0
@@ -1681,6 +1681,25 @@ bool xe_guc_using_main_gamctrl_queues(struct xe_guc *guc) {struct xe_gt *gt =guc_to_gt (guc); +/* +* For Xe3p media gt (35), the GuC and the CS subunits may be still Xe3 +* that lacks the Main GAMCTRL support. Reserved bits from the GMD_ID +* inform the IP version of the subunits. +*/ +if (xe_gt_is_media_type (gt) &&MEDIA_VER (gt_to_xe (gt)) ==35 ) { +u32 val =xe_mmio_read32 (>->mmio,GMD_ID ); +u32 subip =REG_FIELD_GET (GMD_ID_SUBIP_FLAG_MASK , val); + +if (!subip) +return true; + +xe_gt_WARN (gt, subip !=1 , +"GMD_ID has unknown value in the SUBIP_FLAG field - 0x%x\n" , + subip); + +return false; + } +return GT_VER (gt) >=35 ; }
Signature · 1 line
2.51.0
Re: [PATCH 04/23] drm/xe/xe3p_lpm: Add special check in Media GT for Main GAMCTRL
Quoted 44 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
For Xe3p arch some subunits of an IP may be different. The
GMD_IDregister returns the Xe3p arch and dedicates the reserved field to mark possible subunit differences. Generally this is an under-the-hood implementation detail that drivers don't need to worry about, but the newMain_GAMCTRLmay be enabled or not depending on those.Those reserved bits are described for Xe3p as: "If Zero, No special case to be handled. If Non-Zero, special case to be handled by Software agent.". That special case is defined per Arch. So if media version is 35, also check the additional reserved bits. To avoid confusion with the usual meaning of "reserved", define them as
GMD_ID_SUBIP_FLAG_MASK.Bspec: 74201
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 6 ++++++ drivers/gpu/drm/xe/xe_guc.c | 19 +++++++++++++++++++ 2 files changed, 25 insertions(+)drivers/gpu/drm/xe/regs/xe_gt_regs.h +6
-0@@ -37,6 +37,12 @@#define GMD_ID XE_REG(0xd8c)#define GMD_ID_ARCH_MASK REG_GENMASK(31, 22)#define GMD_ID_RELEASE_MASK REG_GENMASK(21, 14) +/* +* Spec defines these bits as "Reserved", but then make them assume some +* meaning that depends on the ARCH. To avoid any confusion, call them +* SUBIP_FLAG_MASK. +*/ +#define GMD_ID_SUBIP_FLAG_MASK REG_GENMASK(13, 6)#define GMD_ID_REVID REG_GENMASK(5, 0)#define FORCEWAKE_ACK_GSC XE_REG(0xdf8)drivers/gpu/drm/xe/xe_guc.c +0
-0
drivers/gpu/drm/xe/xe_guc.c bool xe_guc_using_main_gamctrl_queues(struct xe_guc *guc) · line 1687
Quoted 7 lines
drivers/gpu/drm/xe/xe_guc.c +4
-0@@ -1681,6 +1681,25 @@ bool xe_guc_using_main_gamctrl_queues(struct xe_guc *guc) {struct xe_gt *gt =guc_to_gt (guc); +/* +* For Xe3p media gt (35), the GuC and the CS subunits may be still Xe3 +* that lacks the Main GAMCTRL support. Reserved bits from the GMD_ID +* inform the IP version of the subunits.
See feedback on previous patch; I think it may turn out to be the case that main gamctrl doesn't exist for the media GT even for the cases where GuC and CS subunits are fully Xe3p. If so, we may be able to drop this patch.
Matt
Quoted 22 lines
drivers/gpu/drm/xe/xe_guc.c +15
-0+*/ +if (xe_gt_is_media_type (gt) &&MEDIA_VER (gt_to_xe (gt)) ==35 ) { +u32 val =xe_mmio_read32 (>->mmio,GMD_ID ); +u32 subip =REG_FIELD_GET (GMD_ID_SUBIP_FLAG_MASK , val); + +if (!subip) +return true; + +xe_gt_WARN (gt, subip !=1 , +"GMD_ID has unknown value in the SUBIP_FLAG field - 0x%x\n" , + subip); + +return false; + } +return GT_VER (gt) >=35 ; }Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 5/23 drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
In reply to Lucas De MarchiFrom: Balasubramani Vivekanandan <[email protected]>
CTC_MODE register is removed by Xe3p. Stop reading that register on Xe3p and later platforms.
Bspec: 62395
--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/gpu/drm/xe/xe_gt_clock.c +4 -0
@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2
Signature · 1 line
2.51.0
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
Quoted 6 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Again, maybe I'm referencing the Bspec in a wrong way, but I do see this register existing for IP 35. Maybe a possible tagging issue in the Bspec? Can someone comment here, if I'm missing something.
-shekhar
Quoted 22 lines
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
Quoted 4 lines · Shekhar Chauhan
Quoted 2 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Quoted 8 lines
Quoted 4 lines
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Again, maybe I'm referencing the Bspec in a wrong way, but I do see this register existing for IP 35. Maybe a possible tagging issue in the Bspec? Can someone comment here, if I'm missing something.
So looking a bit closer based on your comment, I think maybe this should actually be a GRAPHICS_VER() test rather than a GT_VER() test. It gets a bit confusing since the bspec website still tries to print stuff out in a platform-based manner, which makes it hard to follow exactly which IP versions and GTs are actually relevant. In this case the first REMOVEDBY() tag listed is what documents the removal of the CTC_MODE register, but it appears that tag only applies to primary GT; the media GT is not included by the change referenced. And then if you look through the jumble of platform names that come after that, it does indeed appear that media is still listed as having the register, but the primary GT no longer appears in the list for platforms with Xe3p IP.
So maybe this is another case where we should be using GRAPHICS_VER instead of GT_VER. I'm not sure it really matters too much though since we don't actually use the register for anything, except to complain about a condition we expect to never show up.
Matt
Quoted 24 lines
-shekhar
Quoted 21 lines
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
Quoted 26 lines · Matt Roper
Quoted 4 lines · Shekhar Chauhan
Quoted 2 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Quoted 8 lines
Quoted 4 lines
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Again, maybe I'm referencing the Bspec in a wrong way, but I do see this register existing for IP 35. Maybe a possible tagging issue in the Bspec? Can someone comment here, if I'm missing something.
So looking a bit closer based on your comment, I think maybe this should actually be a
GRAPHICS_VER()test rather than aGT_VER()test. It gets a bit confusing since the bspec website still tries to print stuff out in a platform-based manner, which makes it hard to follow exactly which IP versions and GTs are actually relevant. In this case the firstREMOVEDBY()tag listed is what documents the removal of theCTC_MODEregister, but it appears that tag only applies to primary GT; the media GT is not included by the change referenced. And then if you look through the jumble of platform names that come after that, it does indeed appear that media is still listed as having the register, but the primary GT no longer appears in the list for platforms with Xe3p IP.
Quoted 4 lines
So maybe this is another case where we should be using
GRAPHICS_VERinstead ofGT_VER. I'm not sure it really matters too much though since we don't actually use the register for anything, except to complain about a condition we expect to never show up.
maybe at this point we should just drop the entire thing? It's not supported for xe2/xe3, it's dropped for xe3p. It's supported for unofficially supported platforms, but we don't really know what to do in that case.
So I think it'd be safe to just drop the entire function and now worry about what is the exact gt version. Thoughts?
Lucas De Marchi
Quoted 34 lines
Matt
Quoted 24 lines
-shekhar
Quoted 21 lines
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2 Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
Quoted 32 lines · Lucas De Marchi
Quoted 26 lines · Matt Roper
Quoted 4 lines · Shekhar Chauhan
Quoted 2 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Quoted 8 lines
Quoted 4 lines
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Again, maybe I'm referencing the Bspec in a wrong way, but I do see this register existing for IP 35. Maybe a possible tagging issue in the Bspec? Can someone comment here, if I'm missing something.
So looking a bit closer based on your comment, I think maybe this should actually be a
GRAPHICS_VER()test rather than aGT_VER()test. It gets a bit confusing since the bspec website still tries to print stuff out in a platform-based manner, which makes it hard to follow exactly which IP versions and GTs are actually relevant. In this case the firstREMOVEDBY()tag listed is what documents the removal of theCTC_MODEregister, but it appears that tag only applies to primary GT; the media GT is not included by the change referenced. And then if you look through the jumble of platform names that come after that, it does indeed appear that media is still listed as having the register, but the primary GT no longer appears in the list for platforms with Xe3p IP.Quoted 4 lines
So maybe this is another case where we should be using
GRAPHICS_VERinstead ofGT_VER. I'm not sure it really matters too much though since we don't actually use the register for anything, except to complain about a condition we expect to never show up.
Quoted 7 lines
maybe at this point we should just drop the entire thing? It's not supported for xe2/xe3, it's dropped for xe3p. It's supported for unofficially supported platforms, but we don't really know what to do in that case.
So I think it'd be safe to just drop the entire function and now worry about what is the exact gt version. Thoughts?
+1 from me to complete remove it.
Regards,
Bala
Quoted 37 lines
Lucas De Marchi
Quoted 34 lines
Matt
Quoted 24 lines
-shekhar
Quoted 21 lines
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2 Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
Quoted 38 lines · Balasubramani
Quoted 37 lines · Lucas De Marchi
Quoted 26 lines · Matt Roper
Quoted 4 lines · Shekhar Chauhan
Quoted 2 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Quoted 8 lines
Quoted 4 lines
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Again, maybe I'm referencing the Bspec in a wrong way, but I do see this register existing for IP 35. Maybe a possible tagging issue in the Bspec? Can someone comment here, if I'm missing something.
So looking a bit closer based on your comment, I think maybe this should actually be a
GRAPHICS_VER()test rather than aGT_VER()test. It gets a bit confusing since the bspec website still tries to print stuff out in a platform-based manner, which makes it hard to follow exactly which IP versions and GTs are actually relevant. In this case the firstREMOVEDBY()tag listed is what documents the removal of theCTC_MODEregister, but it appears that tag only applies to primary GT; the media GT is not included by the change referenced. And then if you look through the jumble of platform names that come after that, it does indeed appear that media is still listed as having the register, but the primary GT no longer appears in the list for platforms with Xe3p IP.Quoted 4 lines
So maybe this is another case where we should be using
GRAPHICS_VERinstead ofGT_VER. I'm not sure it really matters too much though since we don't actually use the register for anything, except to complain about a condition we expect to never show up.maybe at this point we should just drop the entire thing? It's not supported for xe2/xe3, it's dropped for xe3p. It's supported for unofficially supported platforms, but we don't really know what to do in that case.
Quoted 4 lines
Quoted 2 lines
So I think it'd be safe to just drop the entire function and now worry about what is the exact gt version. Thoughts?
+1 from me to complete remove it.
Ack; just dropping it sounds fine to me. I don't believe we've ever seen a log containing the warning that this is set.
Matt
Quoted 41 lines
Regards,
BalaQuoted 37 lines
Lucas De Marchi
Quoted 34 lines
Matt
Quoted 24 lines
-shekhar
Quoted 21 lines
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2 Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
In reply to Lucas De MarchiQuoted 8 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
Quoted 23 lines
--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2 Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 05/23] drm/xe/xe3p_lpm: Stop reading the CTC_MODE register
Quoted 11 lines · Matt Roper
Quoted 8 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
CTC_MODEregister is removed by Xe3p. Stop reading that register on Xe3p and later platforms.Bspec: 62395
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>Reviewed-by Matt Roper <[email protected]>
Actually, based on Shekhar's comment I took a 2nd look and maybe this is a case where it should be a GRAPHICS_VER check instead of GT_VER. See my reply to Shekhar for details.
Matt
Quoted 30 lines
Quoted 24 lines
--- drivers/gpu/drm/xe/xe_gt_clock.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/gpu/drm/xe/xe_gt_clock.c +4
-0@@ -57,6 +57,10 @@ static void read_crystal_clock(struct xe_gt *gt, u32 rpm_config_reg, u32 *freq,static void check_ctc_mode (struct xe_gt *gt) { +/* CTC_MODE register is removed by Xe3p */ +if (GT_VER (gt) >=35 ) +return ; +/* * CTC_MODE[0] = 1 is definitely not supported for Xe2 and later * platforms. In theory it could be a valid setting for pre-Xe2 Signature · 2 lines
-- 2.51.0Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 6/23 drm/xe/xe3p_lpm: Skip disabling NOA on unsupported IPs
In reply to Lucas De MarchiFrom: Balasubramani Vivekanandan <[email protected]>
IP version 35 has removed "NOA Enable Signal" bit from RPM_CONFIG1 register. Skip clearing that bit on unsupported IPs.
--- drivers/gpu/drm/xe/xe_oa.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/xe/xe_oa.c +2 -1
@@ -837,7 +837,8 @@ static void xe_oa_disable_metric_set(struct xe_oa_stream *stream)xe_oa_configure_oa_context (stream, false);/* Make sure we disable noa to save power. */ -xe_mmio_rmw32 (mmio,RPM_CONFIG1 ,GT_NOA_ENABLE ,0 ); +if (GT_VER (stream->gt) <35 ) +xe_mmio_rmw32 (mmio,RPM_CONFIG1 ,GT_NOA_ENABLE ,0 ); sqcnt1 =SQCNT1_PMON_ENABLE | (HAS_OA_BPC_REPORTING (stream->oa->xe) ?SQCNT1_OABPC :0 );
Signature · 1 line
2.51.0
Re: [PATCH 06/23] drm/xe/xe3p_lpm: Skip disabling NOA on unsupported IPs
Quoted 7 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
IP version 35 has removed "NOA Enable Signal" bit from
RPM_CONFIG1register. Skip clearing that bit on unsupported IPs.Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
Bspec: 62391
Quoted 22 lines
--- drivers/gpu/drm/xe/xe_oa.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/xe_oa.c +2
-1@@ -837,7 +837,8 @@ static void xe_oa_disable_metric_set(struct xe_oa_stream *stream)xe_oa_configure_oa_context (stream, false);/* Make sure we disable noa to save power. */ -xe_mmio_rmw32 (mmio,RPM_CONFIG1 ,GT_NOA_ENABLE ,0 ); +if (GT_VER (stream->gt) <35 ) +xe_mmio_rmw32 (mmio,RPM_CONFIG1 ,GT_NOA_ENABLE ,0 ); sqcnt1 =SQCNT1_PMON_ENABLE | (HAS_OA_BPC_REPORTING (stream->oa->xe) ?SQCNT1_OABPC :0 );Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 7/23 drm/xe/xe3p_lpm: Handle MCR steering
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Xe3p_LPM's MCR steering has the same ranges and behavior as Xe3_LPM. However one register range that was reserved on Xe3_LPM has now become a unicast range (0x384200-0x38427F), so we need to stop consolidating the adjacent MCR ranges into a single table entry in the table. With this change to the Xe3_LPM table, we can continue to use the same table for both IP families.
While we're touching this table, take the opportunity to fix a whitespace mistake and clarify that one of the other consolidated range entries includes a reserved range.
Bspec: 76445
--- drivers/gpu/drm/xe/xe_gt_mcr.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/gpu/drm/xe/xe_gt_mcr.c +3 -2
@@ -236,12 +236,13 @@ static const struct xe_mmio_range xe2lpm_instance0_steering_table[] = { };static const struct xe_mmio_range xe3lpm_instance0_steering_table[] = { - {0x384000 ,0x3847DF },/* GAM, rsvd, GAM */ + {0x384000 ,0x3841FF },/* GAM */ + {0x384400 ,0x3847DF },/* GAM */ {0x384900 ,0x384AFF },/* GAM */ {0x389560 ,0x3895FF },/* MEDIAINF */ {0x38B600 ,0x38B8FF },/* L3BANK */ {0x38C800 ,0x38D07F },/* GAM, MEDIAINF */ - {0x38D0D0 ,0x38F0FF },/* MEDIAINF, GAM */ + {0x38D0D0 ,0x38F0FF },/* MEDIAINF, rsvd, GAM */ {0x393C00 ,0x393C7F },/* MEDIAINF */ {}, };
Signature · 1 line
2.51.0
Re: [PATCH 07/23] drm/xe/xe3p_lpm: Handle MCR steering
Quoted 9 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
Xe3p_LPM's MCR steering has the same ranges and behavior as
Xe3_LPM. However one register range that was reserved onXe3_LPMhas now become a unicast range (0x384200-0x38427F), so we need to stop consolidating the adjacent MCR ranges into a single table entry in the table. With this change to theXe3_LPMtable, we can continue to use the same table for both IP families.
Quoted 7 lines
While we're touching this table, take the opportunity to fix a whitespace mistake and clarify that one of the other consolidated range entries includes a reserved range.
Bspec: 76445
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
LGTM.
Quoted 28 lines
--- drivers/gpu/drm/xe/xe_gt_mcr.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)drivers/gpu/drm/xe/xe_gt_mcr.c +3
-2@@ -236,12 +236,13 @@ static const struct xe_mmio_range xe2lpm_instance0_steering_table[] = { };static const struct xe_mmio_range xe3lpm_instance0_steering_table[] = { - {0x384000 ,0x3847DF },/* GAM, rsvd, GAM */ + {0x384000 ,0x3841FF },/* GAM */ + {0x384400 ,0x3847DF },/* GAM */ {0x384900 ,0x384AFF },/* GAM */ {0x389560 ,0x3895FF },/* MEDIAINF */ {0x38B600 ,0x38B8FF },/* L3BANK */ {0x38C800 ,0x38D07F },/* GAM, MEDIAINF */ - {0x38D0D0 ,0x38F0FF },/* MEDIAINF, GAM */ + {0x38D0D0 ,0x38F0FF },/* MEDIAINF, rsvd, GAM */ {0x393C00 ,0x393C7F },/* MEDIAINF */ {}, };Signature · 2 lines
-- 2.51.0
PATCH 8/23 drm/xe/xe3p: Stop programming RCU_MODE's fixed slice mode setting
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Since the hardware load balancing is no longer supported, the programming in RCU_MODE is no longer necessary.
Bspec: 60382
--- drivers/gpu/drm/xe/xe_hw_engine.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/gpu/drm/xe/xe_hw_engine.c +7 -0
@@ -349,6 +349,13 @@ void xe_hw_engine_enable_ring(struct xe_hw_engine *hwe)static bool xe_hw_engine_match_fixed_cslice_mode (const struct xe_gt *gt,const struct xe_hw_engine *hwe) { +/* +* Xe3p no longer supports load balance mode, so "fixed cslice" mode +* is automatic and no RCU_MODE programming is required. +*/ +if (GRAPHICS_VER (gt_to_xe (gt)) >=35 ) +return false; +return xe_gt_ccs_mode_enabled (gt) &&xe_rtp_match_first_render_or_compute (gt, hwe); }
Signature · 1 line
2.51.0
Re: [PATCH 08/23] drm/xe/xe3p: Stop programming RCU_MODE's fixed slice mode setting
Quoted 8 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
Since the hardware load balancing is no longer supported, the programming in
RCU_MODEis no longer necessary.Bspec: 60382
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
LGTM
Quoted 26 lines
--- drivers/gpu/drm/xe/xe_hw_engine.c | 7 +++++++ 1 file changed, 7 insertions(+)drivers/gpu/drm/xe/xe_hw_engine.c +7
-0@@ -349,6 +349,13 @@ void xe_hw_engine_enable_ring(struct xe_hw_engine *hwe)static bool xe_hw_engine_match_fixed_cslice_mode (const struct xe_gt *gt,const struct xe_hw_engine *hwe) { +/* +* Xe3p no longer supports load balance mode, so "fixed cslice" mode +* is automatic and no RCU_MODE programming is required. +*/ +if (GRAPHICS_VER (gt_to_xe (gt)) >=35 ) +return false; +return xe_gt_ccs_mode_enabled (gt) &&xe_rtp_match_first_render_or_compute (gt, hwe); }Signature · 2 lines
-- 2.51.0
PATCH 9/23 drm/xe/xe3p: Determine service copy availability from fuse
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Xe3p introduces a dedicated SERVICE_COPY_ENABLE fuse register to reflect the availability of the service copy engines (BCS1-BCS8).
Bspec: 74624
--- drivers/gpu/drm/xe/regs/xe_gt_regs.h | 3 +++ drivers/gpu/drm/xe/xe_hw_engine.c | 43 ++++++++++++++++++++++++++++-------- 2 files changed, 37 insertions(+), 9 deletions(-)
drivers/gpu/drm/xe/regs/xe_gt_regs.h +3 -0
@@ -245,6 +245,9 @@#define XE2_GT_GEOMETRY_DSS_1 XE_REG(0x9150)#define XE2_GT_GEOMETRY_DSS_2 XE_REG(0x9154) +#define SERVICE_COPY_ENABLE XE_REG(0x9170) +#define FUSE_SERVICE_COPY_ENABLE_MASK REG_GENMASK(7, 0) +#define GDRST XE_REG(0x941c)#define GRDOM_GUC REG_BIT(3)#define GRDOM_FULL REG_BIT(0)
drivers/gpu/drm/xe/xe_hw_engine.c +34 -9
61 lines not on this page · raw message
Signature · 1 line
2.51.0
Re: [PATCH 09/23] drm/xe/xe3p: Determine service copy availability from fuse
Quoting Lucas De Marchi (2025-10-14 00:24:41-03:00)
Quoted 8 lines
From: Matt Roper <[email protected]>
Xe3p introduces a dedicated
SERVICE_COPY_ENABLEfuse register to reflect the availability of the service copy engines (BCS1-BCS8).Bspec: 74624
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
Quoted 89 lines
---
drivers/gpu/drm/xe/regs/xe_gt_regs.h| 3 +++drivers/gpu/drm/xe/xe_hw_engine.c| 43 ++++++++++++++++++++++++++++--------2 files changed, 37 insertions(+), 9 deletions(-)drivers/gpu/drm/xe/regs/xe_gt_regs.h +3
-0@@ -245,6 +245,9 @@#define XE2_GT_GEOMETRY_DSS_1 XE_REG(0x9150)#define XE2_GT_GEOMETRY_DSS_2 XE_REG(0x9154) +#define SERVICE_COPY_ENABLE XE_REG(0x9170) +#define FUSE_SERVICE_COPY_ENABLE_MASK REG_GENMASK(7, 0) +#define GDRST XE_REG(0x941c)#define GRDOM_GUC REG_BIT(3)#define GRDOM_FULL REG_BIT(0)drivers/gpu/drm/xe/xe_hw_engine.c +34
-9@@ -716,27 +716,52 @@ static void read_media_fuses(struct xe_gt *gt) } } +static u32 infer_svccopy_from_meml3 (struct xe_gt *gt) +{ +u32 meml3 =REG_FIELD_GET (MEML3_EN_MASK , +xe_mmio_read32 (>->mmio,MIRROR_FUSE3 )); +u32 svccopy_mask =0 ; + +/* +* Each of the four meml3 bits determines the fusing of two service +* copy engines. +*/ +for (int i =0 ; i <4 ; i++) + svccopy_mask |= (meml3 &BIT (i)) ?0b11 <<2 * i :0 ; + +return svccopy_mask; +} + +static u32 read_svccopy_fuses (struct xe_gt *gt) +{ +return REG_FIELD_GET (FUSE_SERVICE_COPY_ENABLE_MASK , +xe_mmio_read32 (>->mmio,SERVICE_COPY_ENABLE )); +} +static void read_copy_fuses (struct xe_gt *gt) {struct xe_device *xe =gt_to_xe (gt);u32 bcs_mask; -if (GRAPHICS_VERx100 (xe) <1260 ||GRAPHICS_VERx100 (xe) >=1270 ) -return ; -xe_force_wake_assert_held (gt_to_fw (gt),XE_FW_GT ); - bcs_mask =xe_mmio_read32 (>->mmio,MIRROR_FUSE3 ); - bcs_mask =REG_FIELD_GET (MEML3_EN_MASK , bcs_mask); +if (GRAPHICS_VER (xe) >=35 ) + bcs_mask =read_svccopy_fuses (gt); +else if (GRAPHICS_VERx100 (xe) ==1260 ) + bcs_mask =infer_svccopy_from_meml3 (gt); +else +return ; -/* BCS0 is always present; only BCS1-BCS8 may be fused off */ -for (int i =XE_HW_ENGINE_BCS1 , j =0 ; i <=XE_HW_ENGINE_BCS8 ; ++i, ++j) { +/* Only BCS1-BCS8 may be fused off */ + bcs_mask <<=XE_HW_ENGINE_BCS1 ; +for (int i =XE_HW_ENGINE_BCS1 ; i <=XE_HW_ENGINE_BCS8 ; ++i) {if (!(gt->info.engine_mask &BIT (i)))continue ; -if (!(BIT (j /2 ) & bcs_mask)) { +if (!(bcs_mask &BIT (i))) { gt->info.engine_mask &= ~BIT (i); -xe_gt_info (gt,"bcs%u fused off\n" , j); +xe_gt_info (gt,"bcs%u fused off\n" , + i -XE_HW_ENGINE_BCS0 ); } } }Signature · 2 lines
-- 2.51.0
PATCH 10/23 drm/xe/xe3p: Skip TD flush
In reply to Lucas De MarchiFrom: Tejas Upadhyay <[email protected]>
Xe3p has HW ability to do transient display flush so the xe driver can enable this HW feature by default and skip the software TD flush.
Bspec: 60002
--- drivers/gpu/drm/xe/xe_device.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/gpu/drm/xe/xe_device.c +8 -0
@@ -1103,6 +1103,14 @@ void xe_device_td_flush(struct xe_device *xe) {struct xe_gt *root_gt; +/* +* From Xe3p onward the HW takes care of flush of TD entries also along +* with flushing XA entries, which will be at the usual sync points, +* like at the end of submission, so no manual flush is needed here. +*/ +if (GRAPHICS_VER (xe) >=35 ) +return ; +if (!IS_DGFX (xe) ||GRAPHICS_VER (xe) <20 )return ;
Signature · 1 line
2.51.0
Re: [PATCH 10/23] drm/xe/xe3p: Skip TD flush
Quoted 4 lines · Lucas De Marchi
From: Tejas Upadhyay <[email protected]>
Xe3p has HW ability to do transient display flush so the xe driver can enable this HW feature by default and skip the software TD flush.
I think we need to expand on the description here. "has HW ability to do flush" is very ambiguous --- how/when specifically will the hardware decide to flush the TD data if software isn't explicitly triggering it anymore?
If I remember this feature correctly, the actual hardware change here is that "display transient" data will now get flushed automatically anytime "app transient" data gets flushed (whereas previously the display transient data had to be flushed independently). But I don't remember the details for "app transient" off the top of my head now (I remember it was complicated with different rules depending on whether the media hardware was awake or asleep), and there's no reference to it in the driver yet (I believe Xe3p is the first time it shows up, right?). The only Xe3p PAT table we have in this series (Xe3p_XPC) has neither XD nor XA entries, so maybe this patch is coming too early to be useful.
Matt
Quoted 31 lines
Bspec: 60002
Signed-off-by Tejas Upadhyay <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_device.c | 8 ++++++++ 1 file changed, 8 insertions(+)drivers/gpu/drm/xe/xe_device.c +8
-0@@ -1103,6 +1103,14 @@ void xe_device_td_flush(struct xe_device *xe) {struct xe_gt *root_gt; +/* +* From Xe3p onward the HW takes care of flush of TD entries also along +* with flushing XA entries, which will be at the usual sync points, +* like at the end of submission, so no manual flush is needed here. +*/ +if (GRAPHICS_VER (xe) >=35 ) +return ; +if (!IS_DGFX (xe) ||GRAPHICS_VER (xe) <20 )return ;Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 11/23 drm/xe/xe3p: Enable L2 flush optimization feature
In reply to Lucas De MarchiFrom: Tejas Upadhyay <[email protected]>
When set, the L2 flush optimization feature will control whether L2 is in Persistent or Transient mode through monitoring of media activity.
To enable L2 flush optimization include new feature flag GUC_CTL_ENABLE_L2FLUSH_OPT is used when media gt type is detected.
--- drivers/gpu/drm/xe/xe_guc.c | 3 +++ drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 2 files changed, 4 insertions(+)
drivers/gpu/drm/xe/xe_guc.c +3 -0
@@ -94,6 +94,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_guc_using_main_gamctrl_queues (guc)) flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +if (GRAPHICS_VER (xe) >=35 && !IS_DGFX (xe) &&xe_gt_is_media_type (guc_to_gt (guc))) + flags |=GUC_CTL_ENABLE_L2FLUSH_OPT ; +return flags; }
drivers/gpu/drm/xe/xe_guc_fwif.h +1 -0
@@ -115,6 +115,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7)#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14) +#define GUC_CTL_ENABLE_L2FLUSH_OPT BIT(15)#define GUC_CTL_DEBUG 3#define GUC_LOG_VERBOSITY REG_GENMASK(1, 0)
Signature · 1 line
2.51.0
Re: [PATCH 11/23] drm/xe/xe3p: Enable L2 flush optimization feature
Quoted 4 lines · Lucas De Marchi
From: Tejas Upadhyay <[email protected]>
When set, the L2 flush optimization feature will control whether L2 is in Persistent or Transient mode through monitoring of media activity.
Similar to the previous patch, this commit message doesn't really help the reader understand what's going on. I believe the intent here was to inform the GuC that it should be doing some of the special handling for app-transient caching according to whether media is active or not; that's why we have an unusual condition that checks the primary GT's version, but then applies the GuC flag on the media GT.
But as noted on the previous patch, we still don't have a way to mark data as transient yet on Xe3p (of either the display- or app- variety), so this change may be a bit premature; we should postpone this to a later series. And at that time we should probably start out with a kerneldoc patch first that explains these new caching behaviors so that readers have the necessary context before we start changing the code behavior.
Matt
Quoted 42 lines
To enable L2 flush optimization include new feature flag
GUC_CTL_ENABLE_L2FLUSH_OPTis used when media gt type is detected.Cc Gwan-gyeong Mun <[email protected]>Signed-off-by Tejas Upadhyay <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_guc.c | 3 +++ drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 2 files changed, 4 insertions(+)drivers/gpu/drm/xe/xe_guc.c +3
-0@@ -94,6 +94,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_guc_using_main_gamctrl_queues (guc)) flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +if (GRAPHICS_VER (xe) >=35 && !IS_DGFX (xe) &&xe_gt_is_media_type (guc_to_gt (guc))) + flags |=GUC_CTL_ENABLE_L2FLUSH_OPT ; +return flags; }drivers/gpu/drm/xe/xe_guc_fwif.h +1
-0@@ -115,6 +115,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7)#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14) +#define GUC_CTL_ENABLE_L2FLUSH_OPT BIT(15)#define GUC_CTL_DEBUG 3#define GUC_LOG_VERBOSITY REG_GENMASK(1, 0)Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 11/23] drm/xe/xe3p: Enable L2 flush optimization feature
Quoted 13 lines · Matt Roper
Quoted 4 lines · Lucas De Marchi
From: Tejas Upadhyay <[email protected]>
When set, the L2 flush optimization feature will control whether L2 is in Persistent or Transient mode through monitoring of media activity.
Similar to the previous patch, this commit message doesn't really help the reader understand what's going on. I believe the intent here was to inform the GuC that it should be doing some of the special handling for app-transient caching according to whether media is active or not; that's why we have an unusual condition that checks the primary GT's version, but then applies the GuC flag on the media GT.
Quoted 7 lines
But as noted on the previous patch, we still don't have a way to mark data as transient yet on Xe3p (of either the display- or app- variety), so this change may be a bit premature; we should postpone this to a later series. And at that time we should probably start out with a kerneldoc patch first that explains these new caching behaviors so that readers have the necessary context before we start changing the code behavior.
agreed. I will drop this on next rev
thanks
Lucas De Marchi
Quoted 52 lines
Matt
Quoted 42 lines
To enable L2 flush optimization include new feature flag
GUC_CTL_ENABLE_L2FLUSH_OPTis used when media gt type is detected.Cc Gwan-gyeong Mun <[email protected]>Signed-off-by Tejas Upadhyay <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_guc.c | 3 +++ drivers/gpu/drm/xe/xe_guc_fwif.h | 1 + 2 files changed, 4 insertions(+)drivers/gpu/drm/xe/xe_guc.c +3
-0@@ -94,6 +94,9 @@ static u32 guc_ctl_feature_flags(struct xe_guc *guc)if (xe_guc_using_main_gamctrl_queues (guc)) flags |=GUC_CTL_MAIN_GAMCTRL_QUEUES ; +if (GRAPHICS_VER (xe) >=35 && !IS_DGFX (xe) &&xe_gt_is_media_type (guc_to_gt (guc))) + flags |=GUC_CTL_ENABLE_L2FLUSH_OPT ; +return flags; }drivers/gpu/drm/xe/xe_guc_fwif.h +1
-1@@ -115,6 +115,7 @@ struct guc_update_exec_queue_policy {#define GUC_CTL_ENABLE_PSMI_LOGGING BIT(7)#define GUC_CTL_MAIN_GAMCTRL_QUEUES BIT(9)#define GUC_CTL_DISABLE_SCHEDULER BIT(14) +#define GUC_CTL_ENABLE_L2FLUSH_OPT BIT(15)#define GUC_CTL_DEBUG 3#define GUC_LOG_VERBOSITY REG_GENMASK(1, 0) --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 12/23 drm/xe/xe3p: Flush userptr/shrinker bo cachelines manually
In reply to Lucas De MarchiFrom: Tejas Upadhyay <[email protected]>
Starting with Xe3p, HW will flush cachelines marked with XA only when media is off. We have few cases where kernel will have non-XA cachelines which needs manual flush as we postpone the invalidation.
Flush asap from correctness POV to ensure non accelerated CPU copy to swap/shmem file will see coherent view of memory, but also from security POV where later flush can't corrupt the next user of those pages.
[ TODO: xe_device_needs_cache_flush() seems a bad name that doesn't
really review the context - it may need to be renamed/localized ]
--- drivers/gpu/drm/xe/xe_bo.c | 3 ++- drivers/gpu/drm/xe/xe_device.c | 20 ++++++++++++++++++++ drivers/gpu/drm/xe/xe_device.h | 1 + drivers/gpu/drm/xe/xe_userptr.c | 3 ++- 4 files changed, 25 insertions(+), 2 deletions(-)
drivers/gpu/drm/xe/xe_bo.c +2 -1
@@ -673,7 +673,8 @@ static int xe_bo_trigger_rebind(struct xe_device *xe, struct xe_bo *bo,if (!xe_vm_in_fault_mode (vm)) {drm_gpuvm_bo_evict (vm_bo, true); -continue ; +if (!xe_device_needs_cache_flush (xe)) +continue ; }if (!idle) {
drivers/gpu/drm/xe/xe_device.c +20 -0
@@ -1081,6 +1081,26 @@ void xe_device_l2_flush(struct xe_device *xe)xe_force_wake_put (gt_to_fw (gt), fw_ref); } +/** +* xe_device_needs_cache_flush - Whether the cache needs to be flushed +* @xe: The device to check. +* +* Return: true if the device needs cache flush, false otherwise. +*/ +bool xe_device_needs_cache_flush (struct xe_device *xe) +{ +/* +* Xe3p will flush cachelines marked with XA only when media is off. We +* have few cases where kernel will have non-XA cachelines which needs +* manual flush and this is one of them as we postpone the +* invalidation. Flush asap from correctness POV to ensure non +* accelerated CPU copy to swap/shmem file will see coherent view of +* memory, but also from security POV where later flush can't corrupt +* the next user of those pages. +*/ +return GRAPHICS_VER (xe) >=35 && !IS_DGFX (xe); +} +/** * xe_device_td_flush() - Flush transient L3 cache entries * @xe: The device
drivers/gpu/drm/xe/xe_device.h +1 -0
@@ -179,6 +179,7 @@ void xe_device_snapshot_print(struct xe_device *xe, struct drm_printer *p);u64 xe_device_canonicalize_addr (struct xe_device *xe,u64 address);u64 xe_device_uncanonicalize_addr (struct xe_device *xe,u64 address); +bool xe_device_needs_cache_flush (struct xe_device *xe);void xe_device_td_flush (struct xe_device *xe);void xe_device_l2_flush (struct xe_device *xe);
drivers/gpu/drm/xe/xe_userptr.c +2 -1
@@ -112,7 +112,8 @@ static void __vma_userptr_invalidate(struct xe_vm *vm, struct xe_userptr_vma *uv false, MAX_SCHEDULE_TIMEOUT);XE_WARN_ON (err <=0 ); -if (xe_vm_in_fault_mode (vm) && userptr->initial_bind) { +if ((xe_vm_in_fault_mode (vm) ||xe_device_needs_cache_flush (vm->xe)) && + userptr->initial_bind) { err =xe_vm_invalidate_vma (vma);XE_WARN_ON (err); }
Signature · 1 line
2.51.0
Thomas Hellström
maintainerRe: [PATCH 12/23] drm/xe/xe3p: Flush userptr/shrinker bo cachelines manually
Hi,
Quoted 6 lines · Lucas De Marchi
From: Tejas Upadhyay <[email protected]>
Starting with Xe3p, HW will flush cachelines marked with XA only when media is off. We have few cases where kernel will have non-XA cachelines
which needs manual flush as we postpone the invalidation.
is XA- and non-XA cachelines described somewhere in the code?
Quoted 10 lines
Flush asap from correctness POV to ensure non accelerated CPU copy to swap/shmem file will see coherent view of memory, but also from security
POV where later flush can't corrupt the next user of those pages.Signed-off-by Tejas Upadhyay <[email protected]>[ TODO:
xe_device_needs_cache_flush()seems a bad name that doesn't really review the context - it may need to be renamed/localized ]Signed-off-by Lucas De Marchi <[email protected]>
This worries me. Any dma-fence *must*, when signaled, have flushed all caches from data resulting from the operation it marks the completion of. The code below indicates that's not the case?
Note also that the wait for idle in xe_bo_trigger_rebind does not guarantee that the bo is idle, just that there are no pending bind operations.
In fault mode we have a slightly different approach to ensure data is flushed before pages are released.
Could you elaborate a bit on how this is intendend to work.
Thanks,
Thomas
Quoted 93 lines
---
drivers/gpu/drm/xe/xe_bo.c | 3 ++- drivers/gpu/drm/xe/xe_device.c | 20 ++++++++++++++++++++ drivers/gpu/drm/xe/xe_device.h | 1 +drivers/gpu/drm/xe/xe_userptr.c| 3 ++-4 files changed, 25 insertions(+), 2 deletions(-)drivers/gpu/drm/xe/xe_bo.c +0
-0@@ -673,7 +673,8 @@ static int xe_bo_trigger_rebind(struct xe_device *xe, struct xe_bo *bo,
if (!xe_vm_in_fault_mode(vm)) {drm_gpuvm_bo_evict(vm_bo, true);drivers/gpu/drm/xe/xe_bo.c +2
-1-continue ; +if (!xe_device_needs_cache_flush (xe)) +continue ;}
if (!idle) {drivers/gpu/drm/xe/xe_device.c +0
-0@@ -1081,6 +1081,26 @@ void xe_device_l2_flush(struct xe_device *xe) xe_force_wake_put(gt_to_fw(gt), fw_ref); }
+/**
+ *xe_device_needs_cache_flush- Whether the cache needs to be flushed
+ * @xe: The device to check.
+ *
+ * Return: true if the device needs cache flush, false otherwise.
+ */drivers/gpu/drm/xe/xe_device.c +4
-0+bool xe_device_needs_cache_flush (struct xe_device *xe) +{ +/* +* Xe3p will flush cachelines marked with XA only when media is off. We
drivers/gpu/drm/xe/xe_device.c +1
-0+* have few cases where kernel will have non-XA cachelines which needs
drivers/gpu/drm/xe/xe_device.c +2
-0+* manual flush and this is one of them as we postpone the +* invalidation. Flush asap from correctness POV to ensure non
drivers/gpu/drm/xe/xe_device.c +1
-0+* accelerated CPU copy to swap/shmem file will see coherent view of
drivers/gpu/drm/xe/xe_device.c +1
-0+* memory, but also from security POV where later flush can't corrupt
drivers/gpu/drm/xe/xe_device.c +5
-0+* the next user of those pages. +*/ +return GRAPHICS_VER (xe) >=35 && !IS_DGFX (xe); +} +/**
*xe_device_td_flush()- Flush transient L3 cache entries
* @xe: The devicedrivers/gpu/drm/xe/xe_device.h +0
-0@@ -179,6 +179,7 @@ void xe_device_snapshot_print(struct xe_device *xe, struct drm_printer *p); u64 xe_device_canonicalize_addr(struct xe_device *xe, u64 address);u64
xe_device_uncanonicalize_addr(struct xe_device *xe, u64 address);
+boolxe_device_needs_cache_flush(struct xe_device *xe); voidxe_device_td_flush(struct xe_device *xe); voidxe_device_l2_flush(struct xe_device *xe);drivers/gpu/drm/xe/xe_userptr.c +0
-0@@ -112,7 +112,8 @@ static void __vma_userptr_invalidate(struct xe_vm *vm, struct xe_userptr_vma *uv false, MAX_SCHEDULE_TIMEOUT); XE_WARN_ON(err <= 0);drivers/gpu/drm/xe/xe_userptr.c +1
-1-if (xe_vm_in_fault_mode (vm) && userptr->initial_bind) { + if ((xe_vm_in_fault_mode(vm) ||
xe_device_needs_cache_flush(vm->xe)) &&drivers/gpu/drm/xe/xe_userptr.c +1
-0+ userptr->initial_bind) {err =
xe_vm_invalidate_vma(vma);
XE_WARN_ON(err);
}
Re: [PATCH 12/23] drm/xe/xe3p: Flush userptr/shrinker bo cachelines manually
Quoted 11 lines · Thomas Hellström
Hi,
Quoted 6 lines · Lucas De Marchi
From: Tejas Upadhyay <[email protected]>
Starting with Xe3p, HW will flush cachelines marked with XA only when media is off. We have few cases where kernel will have non-XA cachelines
which needs manual flush as we postpone the invalidation.is XA- and non-XA cachelines described somewhere in the code?
no, not yet. See reply from Matt to "[PATCH 10/23] drm/xe/xe3p: Skip TD flush".
I will drop this patch and the 2 before this one on next version.
Lucas De Marchi
Quoted 123 lines
Quoted 11 lines
Flush asap from correctness POV to ensure non accelerated CPU copy to swap/shmem file will see coherent view of memory, but also from security
POV where later flush can't corrupt the next user of those pages.Signed-off-by Tejas Upadhyay <[email protected]>[ TODO:
xe_device_needs_cache_flush()seems a bad name that doesn't really review the context - it may need to be renamed/localized ]Signed-off-by Lucas De Marchi <[email protected]>This worries me. Any dma-fence *must*, when signaled, have flushed all caches from data resulting from the operation it marks the completion of. The code below indicates that's not the case?
Note also that the wait for idle in
xe_bo_trigger_rebinddoes not guarantee that the bo is idle, just that there are no pending bind operations.In fault mode we have a slightly different approach to ensure data is flushed before pages are released.
Could you elaborate a bit on how this is intendend to work.
Thanks,
ThomasQuoted 93 lines
---
drivers/gpu/drm/xe/xe_bo.c | 3 ++- drivers/gpu/drm/xe/xe_device.c | 20 ++++++++++++++++++++ drivers/gpu/drm/xe/xe_device.h | 1 +drivers/gpu/drm/xe/xe_userptr.c| 3 ++-4 files changed, 25 insertions(+), 2 deletions(-)drivers/gpu/drm/xe/xe_bo.c +0
-0@@ -673,7 +673,8 @@ static int xe_bo_trigger_rebind(struct xe_device *xe, struct xe_bo *bo,
if (!xe_vm_in_fault_mode(vm)) {drm_gpuvm_bo_evict(vm_bo, true);drivers/gpu/drm/xe/xe_bo.c +2
-1-continue ; +if (!xe_device_needs_cache_flush (xe)) +continue ;}
if (!idle) {drivers/gpu/drm/xe/xe_device.c +0
-0@@ -1081,6 +1081,26 @@ void xe_device_l2_flush(struct xe_device *xe) xe_force_wake_put(gt_to_fw(gt), fw_ref); }
+/**
+ *xe_device_needs_cache_flush- Whether the cache needs to be flushed
+ * @xe: The device to check.
+ *
+ * Return: true if the device needs cache flush, false otherwise.
+ */drivers/gpu/drm/xe/xe_device.c +4
-0+bool xe_device_needs_cache_flush (struct xe_device *xe) +{ +/* +* Xe3p will flush cachelines marked with XA only when media is off. We
drivers/gpu/drm/xe/xe_device.c +1
-0+* have few cases where kernel will have non-XA cachelines which needs
drivers/gpu/drm/xe/xe_device.c +2
-0+* manual flush and this is one of them as we postpone the +* invalidation. Flush asap from correctness POV to ensure non
drivers/gpu/drm/xe/xe_device.c +1
-0+* accelerated CPU copy to swap/shmem file will see coherent view of
drivers/gpu/drm/xe/xe_device.c +1
-0+* memory, but also from security POV where later flush can't corrupt
drivers/gpu/drm/xe/xe_device.c +5
-0+* the next user of those pages. +*/ +return GRAPHICS_VER (xe) >=35 && !IS_DGFX (xe); +} +/**
*xe_device_td_flush()- Flush transient L3 cache entries
* @xe: The devicedrivers/gpu/drm/xe/xe_device.h +0
-0@@ -179,6 +179,7 @@ void xe_device_snapshot_print(struct xe_device *xe, struct drm_printer *p); u64 xe_device_canonicalize_addr(struct xe_device *xe, u64 address);u64
xe_device_uncanonicalize_addr(struct xe_device *xe, u64 address);
+boolxe_device_needs_cache_flush(struct xe_device *xe); voidxe_device_td_flush(struct xe_device *xe); voidxe_device_l2_flush(struct xe_device *xe);drivers/gpu/drm/xe/xe_userptr.c +0
-0@@ -112,7 +112,8 @@ static void __vma_userptr_invalidate(struct xe_vm *vm, struct xe_userptr_vma *uv false, MAX_SCHEDULE_TIMEOUT); XE_WARN_ON(err <= 0);drivers/gpu/drm/xe/xe_userptr.c +1
-1-if (xe_vm_in_fault_mode (vm) && userptr->initial_bind) { + if ((xe_vm_in_fault_mode(vm) ||
xe_device_needs_cache_flush(vm->xe)) &&drivers/gpu/drm/xe/xe_userptr.c +1
-0+ userptr->initial_bind) {err =
xe_vm_invalidate_vma(vma);
XE_WARN_ON(err);
}
PATCH 13/23 drm/xe: Dump CURRENT_LRCA and CSMQDEBUG registers
In reply to Lucas De MarchiFrom: Wang Xin <[email protected]>
Add CURRENT_LRCA and CSMQDEBUG to register dump to help debugging.
--- drivers/gpu/drm/xe/regs/xe_engine_regs.h | 5 +++ drivers/gpu/drm/xe/xe_guc_capture.c | 53 +++++++++++++++++++++++++++++++- 2 files changed, 57 insertions(+), 1 deletion(-)
drivers/gpu/drm/xe/regs/xe_engine_regs.h +5 -0
@@ -141,6 +141,9 @@#define INHIBIT_SWITCH_UNTIL_PREEMPTED REG_BIT(31)#define IDLE_DELAY REG_GENMASK(20, 0) +#define RING_CURRENT_LRCA (base) XE_REG((base) + 0x240) +#define CURRENT_LRCA_VALID REG_BIT(0) +#define RING_CONTEXT_CONTROL (base) XE_REG((base) + 0x244, XE_REG_OPTION_MASKED)#define CTX_CTRL_PXP_ENABLE REG_BIT(10)#define CTX_CTRL_OAC_CONTEXT_ENABLE REG_BIT(8)
@@ -153,6 +156,8 @@#define GFX_DISABLE_LEGACY_MODE REG_BIT(3)#define GFX_MSIX_INTERRUPT_ENABLE REG_BIT(13) +#define RING_CSMQDEBUG (base) XE_REG((base) + 0x2b0) +#define RING_TIMESTAMP (base) XE_REG((base) + 0x358)#define RING_TIMESTAMP_UDW (base) XE_REG((base) + 0x358 + 4)
drivers/gpu/drm/xe/xe_guc_capture.c +52 -1
83 lines not on this page · raw message
Signature · 1 line
2.51.0
Re: [PATCH 13/23] drm/xe: Dump CURRENT_LRCA and CSMQDEBUG registers
Quoted 3 lines · Lucas De Marchi
From: Wang Xin <[email protected]>
Add
CURRENT_LRCAand CSMQDEBUG to register dump to help debugging.
It might be worth splitting this into two patches since CURRENT_LRCA is something that's been around forever and can already be dumped unconditionally on existing platforms, whereas CSMQDEBUG is a new Xe3p register.
Also, I think CSMQDEBUG dumping would probably make more sense to be included as part of the MQ patch series that Niranjana will be sending later; dumping this register doesn't really have any value outside the context of that other work.
A couple more comments farther down...
Quoted 56 lines
Cc Niranjana Vishwanathapura <[email protected]>Cc Matt Roper <[email protected]>Signed-off-by Wang Xin <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_engine_regs.h | 5 +++ drivers/gpu/drm/xe/xe_guc_capture.c | 53 +++++++++++++++++++++++++++++++- 2 files changed, 57 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_engine_regs.h +5
-0@@ -141,6 +141,9 @@#define INHIBIT_SWITCH_UNTIL_PREEMPTED REG_BIT(31)#define IDLE_DELAY REG_GENMASK(20, 0) +#define RING_CURRENT_LRCA (base) XE_REG((base) + 0x240) +#define CURRENT_LRCA_VALID REG_BIT(0) +#define RING_CONTEXT_CONTROL (base) XE_REG((base) + 0x244, XE_REG_OPTION_MASKED)#define CTX_CTRL_PXP_ENABLE REG_BIT(10)#define CTX_CTRL_OAC_CONTEXT_ENABLE REG_BIT(8)@@ -153,6 +156,8 @@#define GFX_DISABLE_LEGACY_MODE REG_BIT(3)#define GFX_MSIX_INTERRUPT_ENABLE REG_BIT(13) +#define RING_CSMQDEBUG (base) XE_REG((base) + 0x2b0) +#define RING_TIMESTAMP (base) XE_REG((base) + 0x358)#define RING_TIMESTAMP_UDW (base) XE_REG((base) + 0x358 + 4)drivers/gpu/drm/xe/xe_guc_capture.c +4
-0@@ -122,6 +122,7 @@ struct __guc_capture_parsed_output { { RING_IPEHR(0), REG_32BIT, 0, 0, 0, "IPEHR"}, \ { RING_INSTDONE(0), REG_32BIT, 0, 0, 0, "RING_INSTDONE"}, \ { INDIRECT_RING_STATE(0), REG_32BIT, 0, 0, 0, "INDIRECT_RING_STATE"}, \ + { RING_CURRENT_LRCA(0), REG_32BIT, 0, 0, 0, "CURRENT_LRCA"}, \ { RING_ACTHD(0), REG_64BIT_LOW_DW, 0, 0, 0, NULL}, \ { RING_ACTHD_UDW(0), REG_64BIT_HI_DW, 0, 0, 0, "ACTHD"}, \ { RING_BBADDR(0), REG_64BIT_LOW_DW, 0, 0, 0, NULL}, \@@ -149,6 +150,9 @@ struct __guc_capture_parsed_output { { SFC_DONE(2), 0, 0, 0, 0, "SFC_DONE[2]"}, \ { SFC_DONE(3), 0, 0, 0, 0, "SFC_DONE[3]"} +#define XE3P_BASE_ENGINE_INSTANCE \ + { RING_CSMQDEBUG(0), REG_32BIT, 0, 0, 0, "CSMQDEBUG"} + /* XE_LP Global */ static const struct __guc_mmio_reg_descr xe_lp_global_regs[] = { COMMON_XELP_BASE_GLOBAL,
drivers/gpu/drm/xe/xe_guc_capture.c static const struct __guc_mmio_reg_descr xe_lp_gsc_inst_regs[] = { · line 208
Quoted 10 lines
drivers/gpu/drm/xe/xe_guc_capture.c +7
-0@@ -195,6 +199,36 @@ static const struct __guc_mmio_reg_descr xe_lp_gsc_inst_regs[] = { COMMON_BASE_ENGINE_INSTANCE, }; +/* Render / Compute Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_rc_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* Media Decode/Encode Per-Engine-Instance */
I'm also wondering if we really need to dump it for the vcs/vecs/gsc engines; although the register technically exists there, those engines don't actually support MQ so maybe it's only worth dumping on the CCS and BCS engines?
Quoted 49 lines
drivers/gpu/drm/xe/xe_guc_capture.c +38
-0+static const struct __guc_mmio_reg_descr xe3p_vd_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* Video Enhancement Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_vec_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* Blitter Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_blt_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* XE3P - GSC Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_gsc_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; +/* * Empty list to prevent warnings about unknown class/instance types * as not all class/instance types have entries on all platforms. @@ -245,6 +279,21 @@ static const struct __guc_mmio_reg_descr_group xe_hpg_lists[] = { {} }; +/* List of lists for graphic product version >= 3500 */ +static const struct __guc_mmio_reg_descr_group xe3p_lists[] = { +MAKE_REGLIST (xe_lp_global_regs,PF ,GLOBAL ,0 ), +MAKE_REGLIST (xe_hpg_rc_class_regs,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_RENDER_COMPUTE ), +MAKE_REGLIST (xe3p_rc_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_RENDER_COMPUTE ), +MAKE_REGLIST (empty_regs_list,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_VIDEO ), +MAKE_REGLIST (xe3p_vd_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_VIDEO ), +MAKE_REGLIST (xe_vec_class_regs,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_VIDEOENHANCE ), +MAKE_REGLIST (xe3p_vec_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_VIDEOENHANCE ), +MAKE_REGLIST (empty_regs_list,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_BLITTER ), +MAKE_REGLIST (xe3p_blt_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_BLITTER ), +MAKE_REGLIST (empty_regs_list,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_GSC_OTHER ), +MAKE_REGLIST (xe3p_gsc_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_GSC_OTHER ), + {} +};static const char *const capture_list_type_names[] = {"Global" ,"Class" ,
drivers/gpu/drm/xe/xe_guc_capture.c guc_capture_remove_stale_matches_from_list(struct xe_guc_state_capture *gc, · line 344
Quoted 5 lines
drivers/gpu/drm/xe/xe_guc_capture.c +1
-1@@ -292,7 +341,9 @@ guc_capture_remove_stale_matches_from_list(struct xe_guc_state_capture *gc,static const struct __guc_mmio_reg_descr_group *guc_capture_get_device_reglist (struct xe_device *xe) { -if (GRAPHICS_VERx100 (xe) >=1255 ) +if (GRAPHICS_VERx100 (xe) >=3500 )
Since there's no IP with a version of exactly 35.00, I'd just do "GRAPHICS_VER(xe) >= 35" to avoid any confusion. Also in the comment a little bit farther up, I'd replace the "graphic product version >= 3500" with "Xe3p and beyond."
Matt
Quoted 9 lines
drivers/gpu/drm/xe/xe_guc_capture.c +2
-0+return xe3p_lists; + else if (GRAPHICS_VERx100(xe) >= 1255) return xe_hpg_lists; else return xe_lp_lists;Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 13/23] drm/xe: Dump CURRENT_LRCA and CSMQDEBUG registers
Quoted 10 lines · Matt Roper
Quoted 3 lines · Lucas De Marchi
From: Wang Xin <[email protected]>
Add
CURRENT_LRCAand CSMQDEBUG to register dump to help debugging.It might be worth splitting this into two patches since
CURRENT_LRCAis something that's been around forever and can already be dumped unconditionally on existing platforms, whereas CSMQDEBUG is a new Xe3p register.
Quoted 4 lines
Also, I think CSMQDEBUG dumping would probably make more sense to be included as part of the MQ patch series that Niranjana will be sending later; dumping this register doesn't really have any value outside the context of that other work.
ack on splitting. I will do it, but also send the CSMQDEBUG support on next rev. My thought was that have that in would actually help getting the MQ changes. But we can also decide not to pick that patch now, in which case Niranjana can add it to his series.
Quoted 126 lines
A couple more comments farther down...
Quoted 56 lines
Cc Niranjana Vishwanathapura <[email protected]>Cc Matt Roper <[email protected]>Signed-off-by Wang Xin <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_engine_regs.h | 5 +++ drivers/gpu/drm/xe/xe_guc_capture.c | 53 +++++++++++++++++++++++++++++++- 2 files changed, 57 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/regs/xe_engine_regs.h +5
-0@@ -141,6 +141,9 @@#define INHIBIT_SWITCH_UNTIL_PREEMPTED REG_BIT(31)#define IDLE_DELAY REG_GENMASK(20, 0) +#define RING_CURRENT_LRCA (base) XE_REG((base) + 0x240) +#define CURRENT_LRCA_VALID REG_BIT(0) +#define RING_CONTEXT_CONTROL (base) XE_REG((base) + 0x244, XE_REG_OPTION_MASKED)#define CTX_CTRL_PXP_ENABLE REG_BIT(10)#define CTX_CTRL_OAC_CONTEXT_ENABLE REG_BIT(8)@@ -153,6 +156,8 @@#define GFX_DISABLE_LEGACY_MODE REG_BIT(3)#define GFX_MSIX_INTERRUPT_ENABLE REG_BIT(13) +#define RING_CSMQDEBUG (base) XE_REG((base) + 0x2b0) +#define RING_TIMESTAMP (base) XE_REG((base) + 0x358)#define RING_TIMESTAMP_UDW (base) XE_REG((base) + 0x358 + 4)drivers/gpu/drm/xe/xe_guc_capture.c +4
-0@@ -122,6 +122,7 @@ struct __guc_capture_parsed_output { { RING_IPEHR(0), REG_32BIT, 0, 0, 0, "IPEHR"}, \ { RING_INSTDONE(0), REG_32BIT, 0, 0, 0, "RING_INSTDONE"}, \ { INDIRECT_RING_STATE(0), REG_32BIT, 0, 0, 0, "INDIRECT_RING_STATE"}, \ + { RING_CURRENT_LRCA(0), REG_32BIT, 0, 0, 0, "CURRENT_LRCA"}, \ { RING_ACTHD(0), REG_64BIT_LOW_DW, 0, 0, 0, NULL}, \ { RING_ACTHD_UDW(0), REG_64BIT_HI_DW, 0, 0, 0, "ACTHD"}, \ { RING_BBADDR(0), REG_64BIT_LOW_DW, 0, 0, 0, NULL}, \@@ -149,6 +150,9 @@ struct __guc_capture_parsed_output { { SFC_DONE(2), 0, 0, 0, 0, "SFC_DONE[2]"}, \ { SFC_DONE(3), 0, 0, 0, 0, "SFC_DONE[3]"} +#define XE3P_BASE_ENGINE_INSTANCE \ + { RING_CSMQDEBUG(0), REG_32BIT, 0, 0, 0, "CSMQDEBUG"} + /* XE_LP Global */ static const struct __guc_mmio_reg_descr xe_lp_global_regs[] = { COMMON_XELP_BASE_GLOBAL,drivers/gpu/drm/xe/xe_guc_capture.c static const struct __guc_mmio_reg_descr xe_lp_gsc_inst_regs[] = { · line 208
Quoted 10 lines
drivers/gpu/drm/xe/xe_guc_capture.c +7
-0@@ -195,6 +199,36 @@ static const struct __guc_mmio_reg_descr xe_lp_gsc_inst_regs[] = { COMMON_BASE_ENGINE_INSTANCE, }; +/* Render / Compute Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_rc_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* Media Decode/Encode Per-Engine-Instance */ I'm also wondering if we really need to dump it for the vcs/vecs/gsc engines; although the register technically exists there, those engines don't actually support MQ so maybe it's only worth dumping on the CCS and BCS engines?
Quoted 51 lines
drivers/gpu/drm/xe/xe_guc_capture.c +38
-0+static const struct __guc_mmio_reg_descr xe3p_vd_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* Video Enhancement Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_vec_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* Blitter Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_blt_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; + +/* XE3P - GSC Per-Engine-Instance */ +static const struct __guc_mmio_reg_descr xe3p_gsc_inst_regs[] = { +COMMON_BASE_ENGINE_INSTANCE , +XE3P_BASE_ENGINE_INSTANCE , +}; +/* * Empty list to prevent warnings about unknown class/instance types * as not all class/instance types have entries on all platforms. @@ -245,6 +279,21 @@ static const struct __guc_mmio_reg_descr_group xe_hpg_lists[] = { {} }; +/* List of lists for graphic product version >= 3500 */ +static const struct __guc_mmio_reg_descr_group xe3p_lists[] = { +MAKE_REGLIST (xe_lp_global_regs,PF ,GLOBAL ,0 ), +MAKE_REGLIST (xe_hpg_rc_class_regs,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_RENDER_COMPUTE ), +MAKE_REGLIST (xe3p_rc_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_RENDER_COMPUTE ), +MAKE_REGLIST (empty_regs_list,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_VIDEO ), +MAKE_REGLIST (xe3p_vd_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_VIDEO ), +MAKE_REGLIST (xe_vec_class_regs,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_VIDEOENHANCE ), +MAKE_REGLIST (xe3p_vec_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_VIDEOENHANCE ), +MAKE_REGLIST (empty_regs_list,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_BLITTER ), +MAKE_REGLIST (xe3p_blt_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_BLITTER ), +MAKE_REGLIST (empty_regs_list,PF ,ENGINE_CLASS ,GUC_CAPTURE_LIST_CLASS_GSC_OTHER ), +MAKE_REGLIST (xe3p_gsc_inst_regs,PF ,ENGINE_INSTANCE ,GUC_CAPTURE_LIST_CLASS_GSC_OTHER ), + {} +};static const char *const capture_list_type_names[] = {"Global" ,"Class" ,@@ -292,7 +341,9 @@ guc_capture_remove_stale_matches_from_list(struct xe_guc_state_capture *gc,static const struct __guc_mmio_reg_descr_group *guc_capture_get_device_reglist (struct xe_device *xe)
Quoted 8 lines
drivers/gpu/drm/xe/xe_guc_capture.c guc_capture_remove_stale_matches_from_list(struct xe_guc_state_capture *gc, · line 344
Quoted 3 lines
drivers/gpu/drm/xe/xe_guc_capture.c +1
-1{ -if (GRAPHICS_VERx100 (xe) >=1255 ) +if (GRAPHICS_VERx100 (xe) >=3500 )Since there's no IP with a version of exactly 35.00, I'd just do "
GRAPHICS_VER(xe)>= 35" to avoid any confusion. Also in the comment a little bit farther up, I'd replace the "graphic product version >= 3500" with "Xe3p and beyond."
thanks
Lucas De Marchi
Quoted 19 lines
Matt
Quoted 9 lines
drivers/gpu/drm/xe/xe_guc_capture.c +2
-1+return xe3p_lists; + else if (GRAPHICS_VERx100(xe) >= 1255) return xe_hpg_lists; else return xe_lp_lists; --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 14/23 drm/xe/nvl: Define NVL-S platform
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Provide the basic platform definitions and PCI IDs for NVL-S.
--- drivers/gpu/drm/xe/xe_pci.c | 9 +++++++++ drivers/gpu/drm/xe/xe_platform_types.h | 1 + include/drm/intel/pciids.h | 9 +++++++++ 3 files changed, 19 insertions(+)
drivers/gpu/drm/xe/xe_pci.c +9 -0
@@ -354,6 +354,14 @@ static const struct xe_device_desc ptl_desc = { .needs_shared_vf_gt_wq = true, }; +static const struct xe_device_desc nvls_desc = { +PLATFORM (NOVALAKE_S ), + .dma_mask_size =46 , + .has_display = true, + .max_gt_per_tile =2 , + .require_force_probe = true, +}; +#undef PLATFORM__diag_pop ();
@@ -382,6 +390,7 @@ static const struct pci_device_id pciidlist[] = {INTEL_BMG_IDS (INTEL_VGA_DEVICE , &bmg_desc),INTEL_PTL_IDS (INTEL_VGA_DEVICE , &ptl_desc),INTEL_WCL_IDS (INTEL_VGA_DEVICE , &ptl_desc), +INTEL_NVLS_IDS (INTEL_VGA_DEVICE , &nvls_desc), { } };MODULE_DEVICE_TABLE (pci, pciidlist);
drivers/gpu/drm/xe/xe_platform_types.h +1 -0
@@ -24,6 +24,7 @@ enum xe_platform {XE_LUNARLAKE ,XE_BATTLEMAGE ,XE_PANTHERLAKE , + XE_NOVALAKE_S, }; enum xe_subplatform {
include/drm/intel/pciids.h +9 -0
@@ -884,4 +884,13 @@ MACRO__(0xFD80, ## __VA_ARGS__), \ MACRO__(0xFD81, ## __VA_ARGS__) +/* NVL-S */ +#define INTEL_NVLS_IDS (MACRO__ , ...) \ + MACRO__(0xD740, ## __VA_ARGS__), \ + MACRO__(0xD741, ## __VA_ARGS__), \ + MACRO__(0xD742, ## __VA_ARGS__), \ + MACRO__(0xD743, ## __VA_ARGS__), \ + MACRO__(0xD744, ## __VA_ARGS__), \ + MACRO__(0xD745, ## __VA_ARGS__) +#endif /* __PCIIDS_H__ */
Signature · 1 line
2.51.0
Re: [PATCH 14/23] drm/xe/nvl: Define NVL-S platform
Quoted 6 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
Provide the basic platform definitions and PCI IDs for NVL-S.
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
LGTM,
Quoted 64 lines
--- drivers/gpu/drm/xe/xe_pci.c | 9 +++++++++ drivers/gpu/drm/xe/xe_platform_types.h | 1 + include/drm/intel/pciids.h | 9 +++++++++ 3 files changed, 19 insertions(+)drivers/gpu/drm/xe/xe_pci.c +9
-0@@ -354,6 +354,14 @@ static const struct xe_device_desc ptl_desc = { .needs_shared_vf_gt_wq = true, }; +static const struct xe_device_desc nvls_desc = { +PLATFORM (NOVALAKE_S ), + .dma_mask_size =46 , + .has_display = true, + .max_gt_per_tile =2 , + .require_force_probe = true, +}; +#undef PLATFORM__diag_pop ();@@ -382,6 +390,7 @@ static const struct pci_device_id pciidlist[] = {INTEL_BMG_IDS (INTEL_VGA_DEVICE , &bmg_desc),INTEL_PTL_IDS (INTEL_VGA_DEVICE , &ptl_desc),INTEL_WCL_IDS (INTEL_VGA_DEVICE , &ptl_desc), +INTEL_NVLS_IDS (INTEL_VGA_DEVICE , &nvls_desc), { } };MODULE_DEVICE_TABLE (pci, pciidlist);drivers/gpu/drm/xe/xe_platform_types.h +1
-0@@ -24,6 +24,7 @@ enum xe_platform {XE_LUNARLAKE ,XE_BATTLEMAGE ,XE_PANTHERLAKE , + XE_NOVALAKE_S, }; enum xe_subplatform {include/drm/intel/pciids.h +9
-0@@ -884,4 +884,13 @@ MACRO__(0xFD80, ## __VA_ARGS__), \ MACRO__(0xFD81, ## __VA_ARGS__) +/* NVL-S */ +#define INTEL_NVLS_IDS (MACRO__ , ...) \ + MACRO__(0xD740, ## __VA_ARGS__), \ + MACRO__(0xD741, ## __VA_ARGS__), \ + MACRO__(0xD742, ## __VA_ARGS__), \ + MACRO__(0xD743, ## __VA_ARGS__), \ + MACRO__(0xD744, ## __VA_ARGS__), \ + MACRO__(0xD745, ## __VA_ARGS__) +#endif /* __PCIIDS_H__ */
PATCH 15/23 drm/xe/nvls: Define GuC firmware for NVL-S
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Although NVL-S has a similar Xe3 to PTL/WCL, it requires a unique GuC firmware.
--- drivers/gpu/drm/xe/xe_uc_fw.c | 1 + 1 file changed, 1 insertion(+)
drivers/gpu/drm/xe/xe_uc_fw.c +1 -0
@@ -115,6 +115,7 @@ struct fw_blobs_by_type {#define XE_GT_TYPE_ANY XE_GT_TYPE_UNINITIALIZED#define XE_GUC_FIRMWARE_DEFS (fw_def, mmp_ver, major_ver) \ + fw_def(NOVALAKE_S, GT_TYPE_ANY, mmp_ver(xe, guc, nvl, 70, 49, 4)) \ fw_def(PANTHERLAKE, GT_TYPE_ANY, major_ver(xe, guc, ptl, 70, 49, 4)) \ fw_def(BATTLEMAGE, GT_TYPE_ANY, major_ver(xe, guc, bmg, 70, 49, 4)) \ fw_def(LUNARLAKE, GT_TYPE_ANY, major_ver(xe, guc, lnl, 70, 45, 2)) \
Signature · 1 line
2.51.0
Re: [PATCH 15/23] drm/xe/nvls: Define GuC firmware for NVL-S
Quoted 16 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
Although NVL-S has a similar Xe3 to PTL/WCL, it requires a unique GuC firmware.
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>---
drivers/gpu/drm/xe/xe_uc_fw.c| 1 +1 file changed, 1 insertion(+)drivers/gpu/drm/xe/xe_uc_fw.c +0
-0
drivers/gpu/drm/xe/xe_uc_fw.c struct fw_blobs_by_type { · line 118
Quoted 4 lines
drivers/gpu/drm/xe/xe_uc_fw.c +1
-0@@ -115,6 +115,7 @@ struct fw_blobs_by_type {#define XE_GT_TYPE_ANY XE_GT_TYPE_UNINITIALIZED#define XE_GUC_FIRMWARE_DEFS (fw_def, mmp_ver, major_ver) \ + fw_def(NOVALAKE_S, GT_TYPE_ANY, mmp_ver(xe, guc, nvl, 70, 49, 4)) \
just a note that this patch, as a user of mmp_ver() and with no firmware blob published yet, it's targeting the topic/xe-for-CI branch.
Lucas De Marchi
Quoted 7 lines
drivers/gpu/drm/xe/xe_uc_fw.c +0
-0fw_def(PANTHERLAKE, GT_TYPE_ANY, major_ver(xe, guc, ptl, 70, 49, 4)) \ fw_def(BATTLEMAGE, GT_TYPE_ANY, major_ver(xe, guc, bmg, 70, 49, 4)) \fw_def (LUNARLAKE ,GT_TYPE_ANY ,major_ver (xe, guc, lnl,70 ,45 ,2 )) \Signature · 2 lines
-- 2.51.0
PATCH 16/23 drm/xe/nvls: Attach MOCS table for NVL-S
In reply to Lucas De MarchiFrom: Dnyaneshwar Bhadane <[email protected]>
The MOCS table for NVL-S is the same of Xe2.
--- drivers/gpu/drm/xe/xe_mocs.c | 1 + 1 file changed, 1 insertion(+)
drivers/gpu/drm/xe/xe_mocs.c +1 -0
@@ -576,6 +576,7 @@ static unsigned int get_mocs_settings(struct xe_device *xe,memset (info,0 ,sizeof (struct xe_mocs_info ));switch (xe->info.platform) { +case XE_NOVALAKE_S :case XE_PANTHERLAKE :case XE_LUNARLAKE :case XE_BATTLEMAGE :
Signature · 1 line
2.51.0
Re: [PATCH 16/23] drm/xe/nvls: Attach MOCS table for NVL-S
Quoted 3 lines · Lucas De Marchi
From: Dnyaneshwar Bhadane <[email protected]>
The MOCS table for NVL-S is the same of Xe2.
Nitpick: Maybe rephrase it to "The MOCS table for NVL-S is the same as that of Xe2". Also, can we have the Bspec listed for this, to assist the reviewer.
Aside from this, LGTM,
Quoted 20 lines
Signed-off-by Dnyaneshwar Bhadane <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_mocs.c | 1 + 1 file changed, 1 insertion(+)drivers/gpu/drm/xe/xe_mocs.c +1
-0@@ -576,6 +576,7 @@ static unsigned int get_mocs_settings(struct xe_device *xe,memset (info,0 ,sizeof (struct xe_mocs_info ));switch (xe->info.platform) { +case XE_NOVALAKE_S :case XE_PANTHERLAKE :case XE_LUNARLAKE :case XE_BATTLEMAGE :
PATCH 17/23 drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
In reply to Lucas De MarchiFrom: Balasubramani Vivekanandan <[email protected]>
Add support for graphics IP Xe3p_XPC having IP version 35.11.
Bspec: 77979, 77975
--- drivers/gpu/drm/xe/xe_pci.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
drivers/gpu/drm/xe/xe_pci.c +10 -0
@@ -119,6 +119,15 @@ static const struct xe_graphics_desc graphics_xe2 = { XE2_GFX_FEATURES, }; +static const struct xe_graphics_desc graphics_xe3p_xpc = { +XE2_GFX_FEATURES , + .hw_engine_mask = +GENMASK (XE_HW_ENGINE_BCS8 ,XE_HW_ENGINE_BCS1 ) | +GENMASK (XE_HW_ENGINE_CCS3 ,XE_HW_ENGINE_CCS0 ), + .va_bits =57 , + .has_flat_ccs = false, +}; +static const struct xe_media_desc media_xem = { .hw_engine_mask = GENMASK(XE_HW_ENGINE_VCS7, XE_HW_ENGINE_VCS0) |
@@ -151,6 +160,7 @@ static const struct xe_ip graphics_ips[] = { { 3003, "Xe3_LPG", &graphics_xe2 }, { 3004, "Xe3_LPG", &graphics_xe2 }, { 3005, "Xe3_LPG", &graphics_xe2 }, + { 3511, "Xe3p_XPC", &graphics_xe3p_xpc }, };/* Pre-GMDID Media IPs */
Signature · 1 line
2.51.0
Re: [PATCH 17/23] drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
Quoted 16 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Add support for graphics IP
Xe3p_XPChaving IP version 35.11.Bspec: 77979, 77975
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pci.c | 10 ++++++++++ 1 file changed, 10 insertions(+)drivers/gpu/drm/xe/xe_pci.c +0
-0
drivers/gpu/drm/xe/xe_pci.c static const struct xe_graphics_desc graphics_xe2 = { · line 125
Quoted 7 lines
drivers/gpu/drm/xe/xe_pci.c +4
-0@@ -119,6 +119,15 @@ static const struct xe_graphics_desc graphics_xe2 = { XE2_GFX_FEATURES, }; +static const struct xe_graphics_desc graphics_xe3p_xpc = { +XE2_GFX_FEATURES , + .hw_engine_mask = + GENMASK(XE_HW_ENGINE_BCS8, XE_HW_ENGINE_BCS1) |
In Bspec, I see the number of RES_COPY_ENGINES as 0, which signals that there is no BCS0. But, at the same time, I see SERVICE_COPY_ENGINES as 0. So, why are we having a mask from BCS1 to BCS8? Maybe I'm interpreting the table wrong in some way.
But, aside from this change, other changes look fine, I can provide the RB once the above query is clarified.
Quoted 17 lines
drivers/gpu/drm/xe/xe_pci.c +6
-0+ GENMASK(XE_HW_ENGINE_CCS3, XE_HW_ENGINE_CCS0), + .va_bits = 57, + .has_flat_ccs = false, +}; +static const struct xe_media_desc media_xem = { .hw_engine_mask = GENMASK(XE_HW_ENGINE_VCS7, XE_HW_ENGINE_VCS0) |@@ -151,6 +160,7 @@ static const struct xe_ip graphics_ips[] = { { 3003, "Xe3_LPG", &graphics_xe2 }, { 3004, "Xe3_LPG", &graphics_xe2 }, { 3005, "Xe3_LPG", &graphics_xe2 }, + { 3511, "Xe3p_XPC", &graphics_xe3p_xpc }, };/* Pre-GMDID Media IPs */
Re: [PATCH 17/23] drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
Quoted 28 lines · Shekhar Chauhan
Quoted 16 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Add support for graphics IP
Xe3p_XPChaving IP version 35.11.Bspec: 77979, 77975
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>---
drivers/gpu/drm/xe/xe_pci.c| 10 ++++++++++1 file changed, 10 insertions(+)drivers/gpu/drm/xe/xe_pci.c +0
-0drivers/gpu/drm/xe/xe_pci.c static const struct xe_graphics_desc · line 125
Quoted 7 lines
drivers/gpu/drm/xe/xe_pci.c +3
-0@@ -119,6 +119,15 @@ static const struct xe_graphics_desc graphics_xe2 = { XE2_GFX_FEATURES, }; +static const struct xe_graphics_desc graphics_xe3p_xpc = { + XE2_GFX_FEATURES, + .hw_engine_mask = + GENMASK(XE_HW_ENGINE_BCS8, XE_HW_ENGINE_BCS1) |In Bspec, I see the number of
RES_COPY_ENGINESas 0, which signals that there is no BCS0. But, at the same time, I seeSERVICE_COPY_ENGINESas 0. So, why are we having a mask from BCS1 to BCS8? Maybe I'm interpreting the table wrong in some way.
Quoted 1 line
But, aside from this change, other changes look fine, I can provide the RB once the above query is clarified.
Forgot to add the name/signature here, so, for future conversations and references, adding it now,
-shekhar
Quoted 17 lines
Quoted 17 lines
drivers/gpu/drm/xe/xe_pci.c +5
-0+ GENMASK(XE_HW_ENGINE_CCS3, XE_HW_ENGINE_CCS0), + .va_bits = 57, + .has_flat_ccs = false, +}; + static const struct xe_media_desc media_xem = {.hw_engine_mask =
GENMASK(XE_HW_ENGINE_VCS7, XE_HW_ENGINE_VCS0)|drivers/gpu/drm/xe/xe_pci.c +1
-0@@ -151,6 +160,7 @@ static const struct xe_ip graphics_ips[] = { { 3003, "Xe3_LPG", &graphics_xe2 }, { 3004, "Xe3_LPG", &graphics_xe2 }, { 3005, "Xe3_LPG", &graphics_xe2 }, + { 3511, "Xe3p_XPC", &graphics_xe3p_xpc }, }; /* Pre-GMDID Media IPs */
Re: [PATCH 17/23] drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
In reply to Shekhar ChauhanQuoted 13 lines · Shekhar Chauhan
Quoted 11 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Add support for graphics IP
Xe3p_XPChaving IP version 35.11.Bspec: 77979, 77975
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pci.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
Quoted 16 lines
drivers/gpu/drm/xe/xe_pci.c static const struct xe_graphics_desc graphics_xe2 = { · line 124
Quoted 11 lines
drivers/gpu/drm/xe/xe_pci.c +4
-0@@ -119,6 +119,15 @@ static const struct xe_graphics_desc graphics_xe2 = { XE2_GFX_FEATURES, }; +static const struct xe_graphics_desc graphics_xe3p_xpc = { +XE2_GFX_FEATURES , + .hw_engine_mask = + GENMASK(XE_HW_ENGINE_BCS8, XE_HW_ENGINE_BCS1) |In Bspec, I see the number of
RES_COPY_ENGINESas 0, which signals that there is no BCS0. But, at the same time, I seeSERVICE_COPY_ENGINESas 0. So, why are we having a mask from BCS1 to BCS8? Maybe I'm interpreting the table wrong in some way.
The table on page 74110? I see all non-zero values for SERVICE_COPY_ENGINES (which makes sense because I don't think we'd be able to function at all without at least one copy engine to assist with various vram operations).
But note that the details on that page are product/SKU-specific numbers and not something we're allowed to hardcode in the driver. In general we have a way to discover the presence/absence of up to 8 engines via fuses, so we give a mask that matches what the fuses allow us to discover. The actual engine mask will get reduced down during initialization according to what we discover upon fuse readout. We do the same thing with other engine types that are runtime discoverable as well.
Matt
Quoted 20 lines
But, aside from this change, other changes look fine, I can provide the RB once the above query is clarified.
Quoted 16 lines
drivers/gpu/drm/xe/xe_pci.c +6
-0+ GENMASK(XE_HW_ENGINE_CCS3, XE_HW_ENGINE_CCS0), + .va_bits = 57, + .has_flat_ccs = false, +}; +static const struct xe_media_desc media_xem = { .hw_engine_mask = GENMASK(XE_HW_ENGINE_VCS7, XE_HW_ENGINE_VCS0) |@@ -151,6 +160,7 @@ static const struct xe_ip graphics_ips[] = { { 3003, "Xe3_LPG", &graphics_xe2 }, { 3004, "Xe3_LPG", &graphics_xe2 }, { 3005, "Xe3_LPG", &graphics_xe2 }, + { 3511, "Xe3p_XPC", &graphics_xe3p_xpc }, };/* Pre-GMDID Media IPs */
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 17/23] drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
Quoted 43 lines · Matt Roper
Quoted 12 lines · Shekhar Chauhan
Quoted 11 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Add support for graphics IP
Xe3p_XPChaving IP version 35.11.Bspec: 77979, 77975
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pci.c | 10 ++++++++++ 1 file changed, 10 insertions(+)Quoted 15 lines
drivers/gpu/drm/xe/xe_pci.c static const struct xe_graphics_desc graphics_xe2 = { · line 124
Quoted 11 lines
drivers/gpu/drm/xe/xe_pci.c +4
-0@@ -119,6 +119,15 @@ static const struct xe_graphics_desc graphics_xe2 = { XE2_GFX_FEATURES, }; +static const struct xe_graphics_desc graphics_xe3p_xpc = { +XE2_GFX_FEATURES , + .hw_engine_mask = + GENMASK(XE_HW_ENGINE_BCS8, XE_HW_ENGINE_BCS1) |In Bspec, I see the number of
RES_COPY_ENGINESas 0, which signals that there is no BCS0. But, at the same time, I seeSERVICE_COPY_ENGINESas 0. So, why are we having a mask from BCS1 to BCS8? Maybe I'm interpreting the table wrong in some way.The table on page 74110? I see all non-zero values for
SERVICE_COPY_ENGINES(which makes sense because I don't think we'd be able to function at all without at least one copy engine to assist with various vram operations).But note that the details on that page are product/SKU-specific numbers and not something we're allowed to hardcode in the driver. In general we have a way to discover the presence/absence of up to 8 engines via fuses, so we give a mask that matches what the fuses allow us to discover. The actual engine mask will get reduced down during initialization according to what we discover upon fuse readout. We do the same thing with other engine types that are runtime discoverable as well.
Quoted 1 line
Matt
Okay okay, thanks
-shekhar
Quoted 20 lines
Quoted 20 lines
But, aside from this change, other changes look fine, I can provide the RB once the above query is clarified.
Quoted 16 lines
drivers/gpu/drm/xe/xe_pci.c +6
-0+ GENMASK(XE_HW_ENGINE_CCS3, XE_HW_ENGINE_CCS0), + .va_bits = 57, + .has_flat_ccs = false, +}; +static const struct xe_media_desc media_xem = { .hw_engine_mask = GENMASK(XE_HW_ENGINE_VCS7, XE_HW_ENGINE_VCS0) |@@ -151,6 +160,7 @@ static const struct xe_ip graphics_ips[] = { { 3003, "Xe3_LPG", &graphics_xe2 }, { 3004, "Xe3_LPG", &graphics_xe2 }, { 3005, "Xe3_LPG", &graphics_xe2 }, + { 3511, "Xe3p_XPC", &graphics_xe3p_xpc }, };/* Pre-GMDID Media IPs */
Re: [PATCH 17/23] drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition
In reply to Lucas De MarchiQuoted 7 lines · Lucas De Marchi
From: Balasubramani Vivekanandan <[email protected]>
Add support for graphics IP
Xe3p_XPChaving IP version 35.11.Bspec: 77979, 77975
Signed-off-by Balasubramani Vivekanandan <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
Quoted 36 lines
--- drivers/gpu/drm/xe/xe_pci.c | 10 ++++++++++ 1 file changed, 10 insertions(+)drivers/gpu/drm/xe/xe_pci.c +10
-0@@ -119,6 +119,15 @@ static const struct xe_graphics_desc graphics_xe2 = { XE2_GFX_FEATURES, }; +static const struct xe_graphics_desc graphics_xe3p_xpc = { +XE2_GFX_FEATURES , + .hw_engine_mask = +GENMASK (XE_HW_ENGINE_BCS8 ,XE_HW_ENGINE_BCS1 ) | +GENMASK (XE_HW_ENGINE_CCS3 ,XE_HW_ENGINE_CCS0 ), + .va_bits =57 , + .has_flat_ccs = false, +}; +static const struct xe_media_desc media_xem = { .hw_engine_mask = GENMASK(XE_HW_ENGINE_VCS7, XE_HW_ENGINE_VCS0) |@@ -151,6 +160,7 @@ static const struct xe_ip graphics_ips[] = { { 3003, "Xe3_LPG", &graphics_xe2 }, { 3004, "Xe3_LPG", &graphics_xe2 }, { 3005, "Xe3_LPG", &graphics_xe2 }, + { 3511, "Xe3p_XPC", &graphics_xe3p_xpc }, };/* Pre-GMDID Media IPs */ Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 18/23 drm/xe/xe3p_xpc: Add L3 bank mask
In reply to Lucas De MarchiFrom: Fei Yang <[email protected]>
Expose L3 bank mask through topology query interface.
Bspec: 74110
--- drivers/gpu/drm/xe/xe_gt_topology.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/gpu/drm/xe/xe_gt_topology.c +5 -1
@@ -148,7 +148,11 @@ load_l3_bank_mask(struct xe_gt *gt, xe_l3_bank_mask_t l3_bank_mask)if (!xe_gt_topology_report_l3 (gt))return ; -if (GRAPHICS_VER (xe) >=30 ) { +if (GRAPHICS_VERx100 (xe) ==3511 ) { +u32 fuse_val =xe_mmio_read32 (mmio,MIRROR_L3BANK_ENABLE ); + +bitmap_from_arr32 (l3_bank_mask, &fuse_val,32 ); + }else if (GRAPHICS_VER (xe) >=30 ) {xe_l3_bank_mask_t per_node = {};u32 meml3_en =REG_FIELD_GET (XE2_NODE_ENABLE_MASK , fuse3);u32 mirror_l3bank_enable =xe_mmio_read32 (mmio,MIRROR_L3BANK_ENABLE );
Signature · 1 line
2.51.0
Re: [PATCH 18/23] drm/xe/xe3p_xpc: Add L3 bank mask
Quoted 5 lines · Lucas De Marchi
From: Fei Yang <[email protected]>
Expose L3 bank mask through topology query interface.
Bspec: 74110
This is the wrong reference; 73439 is probably the one we want to use.
We should also expand the commit message a bit. On this IP, MIRROR_L3BANK_ENABLE represents the full L3 bank mask (not just a per-node mask), and each bit represents a single bank. That's why we don't need the extra complexity that we had on other recent platforms.
Matt
Quoted 27 lines
Signed-off-by Fei Yang <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_gt_topology.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/xe_gt_topology.c +5
-1@@ -148,7 +148,11 @@ load_l3_bank_mask(struct xe_gt *gt, xe_l3_bank_mask_t l3_bank_mask)if (!xe_gt_topology_report_l3 (gt))return ; -if (GRAPHICS_VER (xe) >=30 ) { +if (GRAPHICS_VERx100 (xe) ==3511 ) { +u32 fuse_val =xe_mmio_read32 (mmio,MIRROR_L3BANK_ENABLE ); + +bitmap_from_arr32 (l3_bank_mask, &fuse_val,32 ); + }else if (GRAPHICS_VER (xe) >=30 ) {xe_l3_bank_mask_t per_node = {};u32 meml3_en =REG_FIELD_GET (XE2_NODE_ENABLE_MASK , fuse3);u32 mirror_l3bank_enable =xe_mmio_read32 (mmio,MIRROR_L3BANK_ENABLE );Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 19/23 drm/xe/xe3p_xpc: Add MCR steering
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Xe3p_XPC's steering has a few changes from Xe3. Aside from minor changes to the XeCore (the new name for what used to be "DSS") and INSTANCE0 tables, different rules apply to different subranges of type "GAM." Certain GAM subranges require steering to grp/instance (0,0) (and thus use the INSTANCE0 table), while others require special steering to (1,0) instead. Similarly, there are multiple classes of "PSMI" steering, with some requiring steering to (0,0) while others require (19,0).
FIXME: There's an "L3BANK" range listed in the bspec that needs clarification.
Bspec: 74418
--- drivers/gpu/drm/xe/xe_gt_mcr.c | 56 ++++++++++++++++++++++++++++++++++++++-- drivers/gpu/drm/xe/xe_gt_types.h | 15 +++++++++++ 2 files changed, 69 insertions(+), 2 deletions(-)
drivers/gpu/drm/xe/xe_gt_mcr.c +54 -2
@@ -169,6 +169,15 @@ static const struct xe_mmio_range xelpg_dss_steering_table[] = { {}, }; +static const struct xe_mmio_range xe3p_xpc_xecore_steering_table[] = { + {0x008140 ,0x00817F },/* SLICE, XeCore, SLICE */ + {0x009480 ,0x00955F },/* SLICE, XeCore */ + {0x00D800 ,0x00D87F },/* SLICE */ + {0x00DC00 ,0x00E9FF },/* SLICE, rsvd, XeCore, rsvd, XeCore, rsvd, XeCore */ + {0x013000 ,0x0135FF },/* XeCore, SLICE */ + {}, +}; +static const struct xe_mmio_range xelpmp_oaddrm_steering_table[] = { {0x393200 ,0x39323F }, {0x393400 ,0x3934FF },
@@ -247,6 +256,30 @@ static const struct xe_mmio_range xe3lpm_instance0_steering_table[] = { {}, }; +/* +* Different "GAM" ranges have different rules; GAMWKRS, STLB, and GAMREQSTRM +* range subtypes need to be steered to (1,0), while all other GAM subtypes +* are steered to (0,0) and are included in the "INSTANCE0" table farther +* down. +*/ +static const struct xe_mmio_range xe3p_xpc_gam_grp1_steering_table[] = { + {0x004000 ,0x004AFF },/* GAMREQSTRM, rsvd, STLB, GAMWKRS, GAMREQSTRM */ + {0x00F100 ,0x00FFFF },/* GAMWKRS */ + {}, +}; + +static const struct xe_mmio_range xe3p_xpc_psmi_grp19_steering_table[] = { + {0x00B500 ,0x00B5FF }, + {}, +}; + +static const struct xe_mmio_range xe3p_xpc_instance0_steering_table[] = { + {0x00B600 ,0x00B6FF },/* PSMI0 */ + {0x00C800 ,0x00CFFF },/* GAMCTRL */ + {0x00F000 ,0x00F0FF },/* GAMCTRL */ + {}, +}; +static void init_steering_l3bank (struct xe_gt *gt) {struct xe_mmio *mmio = >->mmio;
@@ -419,6 +452,18 @@ static void init_steering_sqidi_psmi(struct xe_gt *gt) gt->steering[SQIDI_PSMI ].instance_target = select &0x1 ; } +static void init_steering_psmi (struct xe_gt *gt) +{ + gt->steering[PSMI19 ].group_target =19 ; + gt->steering[PSMI19 ].instance_target =0 ; +} + +static void init_steering_gam1 (struct xe_gt *gt) +{ + gt->steering[GAM1 ].group_target =1 ; + gt->steering[GAM1 ].instance_target =0 ; +} + static const struct { const char *name; void (*init)(struct xe_gt *gt);
@@ -426,9 +471,11 @@ static const struct { [L3BANK] = { "L3BANK", init_steering_l3bank }, [MSLICE] = { "MSLICE", init_steering_mslice }, [LNCF] = { "LNCF", NULL }, /* initialized by mslice init */ - [DSS] = { "DSS", init_steering_dss }, + [DSS] = { "DSS / XeCore", init_steering_dss }, [OADDRM] = { "OADDRM / GPMXMT", init_steering_oaddrm }, [SQIDI_PSMI] = { "SQIDI_PSMI", init_steering_sqidi_psmi }, + [PSMI19] = { "PSMI[19]", init_steering_psmi }, + [GAM1] = { "GAMWKRS / STLB / GAMREQSTRM", init_steering_gam1 }, [INSTANCE0] = { "INSTANCE 0", NULL }, [IMPLICIT_STEERING] = { "IMPLICIT", NULL }, };
@@ -467,7 +514,12 @@ void xe_gt_mcr_init_early(struct xe_gt *gt) gt->steering[OADDRM ].ranges = xelpmp_oaddrm_steering_table; } }else { -if (GRAPHICS_VER (xe) >=20 ) { +if (GRAPHICS_VERx100 (xe) ==3511 ) { + gt->steering[DSS ].ranges = xe3p_xpc_xecore_steering_table; + gt->steering[GAM1 ].ranges = xe3p_xpc_gam_grp1_steering_table; + gt->steering[INSTANCE0 ].ranges = xe3p_xpc_instance0_steering_table; + gt->steering[PSMI19 ].ranges = xe3p_xpc_psmi_grp19_steering_table; + }else if (GRAPHICS_VER (xe) >=20 ) { gt->steering[DSS ].ranges = xe2lpg_dss_steering_table; gt->steering[SQIDI_PSMI ].ranges = xe2lpg_sqidi_psmi_steering_table; gt->steering[INSTANCE0 ].ranges = xe2lpg_instance0_steering_table;
drivers/gpu/drm/xe/xe_gt_types.h +15 -0
@@ -72,6 +72,21 @@ enum xe_steering_type {OADDRM ,SQIDI_PSMI , +/* +* The bspec lists multiple ranges as "PSMI," but the different +* ranges with that label have different grpid steering values so we +* treat them independently in code. Note that the ranges with grpid=0 +* are included in the INSTANCE0 group above. +*/ +PSMI19 , + +/* +* Although most GAM ranges must be steered to (0,0) and thus use the +* INSTANCE0 type farther down, some platforms have special rules +* for specific subtypes that require steering to (1,0) instead. +*/ +GAM1 , +/* * On some platforms there are multiple types of MCR registers that * will always return a non-terminated value at instance (0, 0). We'll
Signature · 1 line
2.51.0
PATCH 20/23 drm/xe/xe3p_xpc: Add support for compute walker for non-MSIx
In reply to Lucas De MarchiFrom: S A Muqthyar Ahmed <[email protected]>
Current implementation of compute walker has dependency on GPU/SW Stack which requires SW/UMD to wait for event from KMD to indicate PIPE_CONTROL interrup was done. This created latency on SW stack.
This feature adds support to generate completion interrupt from GPGPU walker which does not support MSIx and avoid software using Pipe control drain/idle latency.
--- drivers/gpu/drm/xe/regs/xe_irq_regs.h | 1 + drivers/gpu/drm/xe/xe_irq.c | 4 ++++ 2 files changed, 5 insertions(+)
drivers/gpu/drm/xe/regs/xe_irq_regs.h +1 -0
@@ -82,6 +82,7 @@#define GSC_ER_COMPLETE REG_BIT(5)#define GT_RENDER_PIPECTL_NOTIFY_INTERRUPT REG_BIT(4)#define GT_CS_MASTER_ERROR_INTERRUPT REG_BIT(3) +#define GT_COMPUTE_WALKER_INTERRUPT REG_BIT(2)#define GT_RENDER_USER_INTERRUPT REG_BIT(0)/* irqs for OTHER_KCR_INSTANCE */
drivers/gpu/drm/xe/xe_irq.c +4 -0
@@ -150,6 +150,10 @@ void xe_irq_enable_hwe(struct xe_gt *gt)if (xe_device_uc_enabled (xe)) { irqs =GT_RENDER_USER_INTERRUPT |GT_RENDER_PIPECTL_NOTIFY_INTERRUPT ; + +/* Enable Compute Walker Interrupt for non-MSIX platforms */ +if (GRAPHICS_VERx100 (xe) >=3511 && !xe_device_has_msix (xe)) + irqs |=GT_COMPUTE_WALKER_INTERRUPT ; }else { irqs =GT_RENDER_USER_INTERRUPT | GT_CS_MASTER_ERROR_INTERRUPT |
Signature · 1 line
2.51.0
Re: [PATCH 20/23] drm/xe/xe3p_xpc: Add support for compute walker for non-MSIx
Quoted 35 lines · Lucas De Marchi
From: S A Muqthyar Ahmed <[email protected]>
Current implementation of compute walker has dependency on GPU/SW Stack which requires SW/UMD to wait for event from KMD to indicate
PIPE_CONTROLinterrup was done. This created latency on SW stack.This feature adds support to generate completion interrupt from GPGPU walker which does not support MSIx and avoid software using Pipe control drain/idle latency.
Suggested-by Himal Prasad Ghimiray <[email protected]>Signed-off-by S A Muqthyar Ahmed <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_irq_regs.h | 1 + drivers/gpu/drm/xe/xe_irq.c | 4 ++++ 2 files changed, 5 insertions(+)drivers/gpu/drm/xe/regs/xe_irq_regs.h +1
-0@@ -82,6 +82,7 @@#define GSC_ER_COMPLETE REG_BIT(5)#define GT_RENDER_PIPECTL_NOTIFY_INTERRUPT REG_BIT(4)#define GT_CS_MASTER_ERROR_INTERRUPT REG_BIT(3) +#define GT_COMPUTE_WALKER_INTERRUPT REG_BIT(2)#define GT_RENDER_USER_INTERRUPT REG_BIT(0)/* irqs for OTHER_KCR_INSTANCE */ drivers/gpu/drm/xe/xe_irq.c +0
-0
drivers/gpu/drm/xe/xe_irq.c void xe_irq_enable_hwe(struct xe_gt *gt) · line 156
Quoted 7 lines
drivers/gpu/drm/xe/xe_irq.c +4
-0@@ -150,6 +150,10 @@ void xe_irq_enable_hwe(struct xe_gt *gt)if (xe_device_uc_enabled (xe)) { irqs =GT_RENDER_USER_INTERRUPT |GT_RENDER_PIPECTL_NOTIFY_INTERRUPT ; + +/* Enable Compute Walker Interrupt for non-MSIX platforms */ +if (GRAPHICS_VERx100 (xe) >=3511 && !xe_device_has_msix (xe)) + irqs |=GT_COMPUTE_WALKER_INTERRUPT ;
This bit only exists in the compute engine interrupt vector (bspec 62346) and render engine interrupt vector (bspec 62353). It does not exist in the blitter (62345), vcs (62354), vecs (62355), or gsc (63341), which makes sense because none of those engines can run compute walkers. Should we be making sure we only try to unmask and enable this interrupt on supported engine types?
Matt
Quoted 7 lines
drivers/gpu/drm/xe/xe_irq.c +0
-0}else { irqs =GT_RENDER_USER_INTERRUPT | GT_CS_MASTER_ERROR_INTERRUPT |Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 20/23] drm/xe/xe3p_xpc: Add support for compute walker for non-MSIx
Quoted 42 lines · Matt Roper
Quoted 41 lines · Lucas De Marchi
From: S A Muqthyar Ahmed <[email protected]>
Current implementation of compute walker has dependency on GPU/SW Stack which requires SW/UMD to wait for event from KMD to indicate
PIPE_CONTROLinterrup was done. This created latency on SW stack.This feature adds support to generate completion interrupt from GPGPU walker which does not support MSIx and avoid software using Pipe control drain/idle latency.
Suggested-by Himal Prasad Ghimiray <[email protected]>Signed-off-by S A Muqthyar Ahmed <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_irq_regs.h | 1 + drivers/gpu/drm/xe/xe_irq.c | 4 ++++ 2 files changed, 5 insertions(+)drivers/gpu/drm/xe/regs/xe_irq_regs.h +1
-0@@ -82,6 +82,7 @@#define GSC_ER_COMPLETE REG_BIT(5)#define GT_RENDER_PIPECTL_NOTIFY_INTERRUPT REG_BIT(4)#define GT_CS_MASTER_ERROR_INTERRUPT REG_BIT(3) +#define GT_COMPUTE_WALKER_INTERRUPT REG_BIT(2)#define GT_RENDER_USER_INTERRUPT REG_BIT(0)/* irqs for OTHER_KCR_INSTANCE */ drivers/gpu/drm/xe/xe_irq.c +3
-0@@ -150,6 +150,10 @@ void xe_irq_enable_hwe(struct xe_gt *gt)if (xe_device_uc_enabled (xe)) { irqs =GT_RENDER_USER_INTERRUPT |GT_RENDER_PIPECTL_NOTIFY_INTERRUPT ; + +/* Enable Compute Walker Interrupt for non-MSIX platforms */ +if (GRAPHICS_VERx100 (xe) >=3511 && !xe_device_has_msix (xe))
Quoted 8 lines
drivers/gpu/drm/xe/xe_irq.c void xe_irq_enable_hwe(struct xe_gt *gt) · line 156
Quoted 1 line
drivers/gpu/drm/xe/xe_irq.c +1
-0+ irqs |=GT_COMPUTE_WALKER_INTERRUPT ;This bit only exists in the compute engine interrupt vector (bspec 62346) and render engine interrupt vector (bspec 62353). It does not exist in the blitter (62345), vcs (62354), vecs (62355), or gsc (63341), which makes sense because none of those engines can run compute walkers. Should we be making sure we only try to unmask and enable this interrupt on supported engine types?
right... but then we also have similar issues about being lazy with other bits as well. Checking the other interrupt vector structures, bit 2 is not defined for them.
I'm leaning towards we are being lazy in the programming here and this is not currently a problem. Then we can refactor this on top to stop being lazy and make the intention of the code clearer (e.g. I don't really like that use of smask/dmask because engines are bundled together in a single register).
Lucas De Marchi
Quoted 17 lines
Matt
Quoted 7 lines
drivers/gpu/drm/xe/xe_irq.c +0
-1}else { irqs =GT_RENDER_USER_INTERRUPT | GT_CS_MASTER_ERROR_INTERRUPT | --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 20/23] drm/xe/xe3p_xpc: Add support for compute walker for non-MSIx
Quoted 56 lines · Lucas De Marchi
Quoted 42 lines · Matt Roper
Quoted 41 lines · Lucas De Marchi
From: S A Muqthyar Ahmed <[email protected]>
Current implementation of compute walker has dependency on GPU/SW Stack which requires SW/UMD to wait for event from KMD to indicate
PIPE_CONTROLinterrup was done. This created latency on SW stack.This feature adds support to generate completion interrupt from GPGPU walker which does not support MSIx and avoid software using Pipe control drain/idle latency.
Suggested-by Himal Prasad Ghimiray <[email protected]>Signed-off-by S A Muqthyar Ahmed <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/regs/xe_irq_regs.h | 1 + drivers/gpu/drm/xe/xe_irq.c | 4 ++++ 2 files changed, 5 insertions(+)drivers/gpu/drm/xe/regs/xe_irq_regs.h +1
-0@@ -82,6 +82,7 @@#define GSC_ER_COMPLETE REG_BIT(5)#define GT_RENDER_PIPECTL_NOTIFY_INTERRUPT REG_BIT(4)#define GT_CS_MASTER_ERROR_INTERRUPT REG_BIT(3) +#define GT_COMPUTE_WALKER_INTERRUPT REG_BIT(2)#define GT_RENDER_USER_INTERRUPT REG_BIT(0)/* irqs for OTHER_KCR_INSTANCE */ drivers/gpu/drm/xe/xe_irq.c +3
-0@@ -150,6 +150,10 @@ void xe_irq_enable_hwe(struct xe_gt *gt)if (xe_device_uc_enabled (xe)) { irqs =GT_RENDER_USER_INTERRUPT |GT_RENDER_PIPECTL_NOTIFY_INTERRUPT ; + +/* Enable Compute Walker Interrupt for non-MSIX platforms */ +if (GRAPHICS_VERx100 (xe) >=3511 && !xe_device_has_msix (xe))Quoted 8 lines
drivers/gpu/drm/xe/xe_irq.c void xe_irq_enable_hwe(struct xe_gt *gt) · line 156
Quoted 1 line
drivers/gpu/drm/xe/xe_irq.c +1
-0+ irqs |=GT_COMPUTE_WALKER_INTERRUPT ;This bit only exists in the compute engine interrupt vector (bspec 62346) and render engine interrupt vector (bspec 62353). It does not exist in the blitter (62345), vcs (62354), vecs (62355), or gsc (63341), which makes sense because none of those engines can run compute walkers. Should we be making sure we only try to unmask and enable this interrupt on supported engine types?
right... but then we also have similar issues about being lazy with other bits as well. Checking the other interrupt vector structures, bit 2 is not defined for them.
Quoted 5 lines
I'm leaning towards we are being lazy in the programming here and this is not currently a problem. Then we can refactor this on top to stop being lazy and make the intention of the code clearer (e.g. I don't really like that use of smask/dmask because engines are bundled together in a single register).
My main worry here is that since different engines do explicitly have different interrupt vectors, there's more potential for a future platform to use this "unused" bit for a completely different type of interrupt on blitter, media, etc. That would be easy for us to overlook during early platform bringup.
It's less likely that the enable/mask bits for an engine (for example, BCS6) would get repurposed on a platform that doesn't have that engine, because the engine still has reserved register ranges and such in the architecture, even for individual platforms that don't use it.
Matt
Quoted 20 lines
Lucas De Marchi
Quoted 17 lines
Matt
Quoted 7 lines
drivers/gpu/drm/xe/xe_irq.c +0
-1}else { irqs =GT_RENDER_USER_INTERRUPT | GT_CS_MASTER_ERROR_INTERRUPT | --2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
PATCH 21/23 drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In Xe3p_XPC (and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.
Note that our xe_rtp_match_has_flatccs() function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.
--- drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++ drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++ drivers/gpu/drm/xe/xe_tuning.c | 9 ++++++--- 3 files changed, 22 insertions(+), 3 deletions(-)
drivers/gpu/drm/xe/xe_rtp.c +6 -0
@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, {return xe_gt_has_discontiguous_dss_groups (gt); } + +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe) +{ +return gt_to_xe (gt)->info.has_flat_ccs; +}
drivers/gpu/drm/xe/xe_rtp.h +10 -0
@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const struct xe_gt *gt,bool xe_rtp_match_gt_has_discontiguous_dss_groups (const struct xe_gt *gt,const struct xe_hw_engine *hwe); +/** +* xe_rtp_match_has_flat_ccs - Match when platform has FlatCCS compression +* @gt: GT structure +* @hwe: Engine instance +* +* Returns: true if platform has FlatCCS compression, false otherwise +*/ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe); +#endif
drivers/gpu/drm/xe/xe_tuning.c +6 -3
@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, {XE_RTP_NAME ("Tuning: Compression Overfetch" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (CLR (CCCHKNREG1 ,ENCOMPPERFFIX ),SET (CCCHKNREG1 ,L3CMPCTRL )) },
@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = {XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG3 ,COMPPWOVERFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), -XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) },
Signature · 1 line
2.51.0
Re: [PATCH 21/23] drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
Quoted 15 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In
Xe3p_XPC(and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.Note that our
xe_rtp_match_has_flatccs()function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.
Quoted 2 lines
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>
The patch in itself looks fine to me, but, the patch doesn't specifically play only around Xe3p_XPC. Maybe we can move this patch out of the current series, or if we wish to keep it here, can we instead drop the xe3p_xpc from the prefix? Thoughts?
Quoted 71 lines
--- drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++ drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++ drivers/gpu/drm/xe/xe_tuning.c | 9 ++++++--- 3 files changed, 22 insertions(+), 3 deletions(-)drivers/gpu/drm/xe/xe_rtp.c +6
-0@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, {return xe_gt_has_discontiguous_dss_groups (gt); } + +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe) +{ +return gt_to_xe (gt)->info.has_flat_ccs; +}drivers/gpu/drm/xe/xe_rtp.h +10
-0@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const struct xe_gt *gt,bool xe_rtp_match_gt_has_discontiguous_dss_groups (const struct xe_gt *gt,const struct xe_hw_engine *hwe); +/** +* xe_rtp_match_has_flat_ccs - Match when platform has FlatCCS compression +* @gt: GT structure +* @hwe: Engine instance +* +* Returns: true if platform has FlatCCS compression, false otherwise +*/ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe); +#endif drivers/gpu/drm/xe/xe_tuning.c +6
-3@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, {XE_RTP_NAME ("Tuning: Compression Overfetch" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (CLR (CCCHKNREG1 ,ENCOMPPERFFIX ),SET (CCCHKNREG1 ,L3CMPCTRL )) },@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = {XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG3 ,COMPPWOVERFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), -XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) },
Re: [PATCH 21/23] drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
Quoted 17 lines · Shekhar Chauhan
Quoted 15 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In
Xe3p_XPC(and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.Note that our
xe_rtp_match_has_flatccs()function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.
Quoted 3 lines
Quoted 2 lines
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>The patch in itself looks fine to me, but, the patch doesn't specifically play only around
Xe3p_XPC. Maybe we can move this patch out of the current series, or if we wish to keep it here, can we instead drop thexe3p_xpcfrom the prefix? Thoughts?
Forgot to add the name/signature here, apologies, and adding it now for future references/conversations,
-shekhar
Quoted 79 lines
Quoted 79 lines
---
drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++
drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++
drivers/gpu/drm/xe/xe_tuning.c| 9 ++++++---3 files changed, 22 insertions(+), 3 deletions(-)drivers/gpu/drm/xe/xe_rtp.c +0
-0@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, { return xe_gt_has_discontiguous_dss_groups(gt);}
drivers/gpu/drm/xe/xe_rtp.c +6
-0+ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, + const struct xe_hw_engine *hwe) +{ + return gt_to_xe(gt)->info.has_flat_ccs; +}drivers/gpu/drm/xe/xe_rtp.h +0
-0@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const structxe_gt *gt, bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, const struct xe_hw_engine *hwe);+/**
+ *xe_rtp_match_has_flat_ccs- Match when platform has FlatCCS compression
+ * @gt: GT structure
+ * @hwe: Engine instance
+ *
+ * Returns: true if platform has FlatCCS compression, false otherwise
+ */drivers/gpu/drm/xe/xe_rtp.h +3
-0+bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, + const struct xe_hw_engine *hwe); +#endif
drivers/gpu/drm/xe/xe_tuning.c +2
-1@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, { XE_RTP_NAME("Tuning: Compression Overfetch"), - XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED)), + XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001,XE_RTP_END_VERSION_UNDEFINED ), + FUNC(xe_rtp_match_has_flat_ccs)), XE_RTP_ACTIONS(CLR(CCCHKNREG1, ENCOMPPERFFIX),
SET(CCCHKNREG1, L3CMPCTRL))
},drivers/gpu/drm/xe/xe_tuning.c +3
-2@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { XE_RTP_ACTIONS(SET(XE2LPM_L3SQCREG3, COMPPWOVERFETCHEN)) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), - XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED)), + XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED), + FUNC(xe_rtp_match_has_flat_ccs)), XE_RTP_ACTIONS(SET(L3SQCREG2, COMPMEMRD256BOVRFETCHEN)) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), - XE_RTP_RULES(MEDIA_VERSION_RANGE(2000, XE_RTP_END_VERSION_UNDEFINED)), + XE_RTP_RULES(MEDIA_VERSION_RANGE(2000,
XE_RTP_END_VERSION_UNDEFINED),
+FUNC(xe_rtp_match_has_flat_ccs)),
XE_RTP_ACTIONS(SET(XE2LPM_L3SQCREG2,
COMPMEMRD256BOVRFETCHEN))
},
Re: [PATCH 21/23] drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
In reply to Shekhar ChauhanQuoted 17 lines · Shekhar Chauhan
Quoted 15 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In
Xe3p_XPC(and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.Note that our
xe_rtp_match_has_flatccs()function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.
Quoted 6 lines
Quoted 2 lines
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>The patch in itself looks fine to me, but, the patch doesn't specifically play only around
Xe3p_XPC. Maybe we can move this patch out of the current series, or if we wish to keep it here, can we instead drop thexe3p_xpcfrom the prefix? Thoughts?
Aside from PVC (which is Xe1 and not relevant to these tuning settings), Xe3p_XPC is the only IP we have without FlatCCS in the design, so at the moment this patch is specific to Xe3p_XPC. As a general architecture though, if we eventually wind up with other IPs down the road that also lack FlatCCS, then these tuning settings will also not apply to them for the same reasons.
Matt
Quoted 70 lines
Quoted 70 lines
--- drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++ drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++ drivers/gpu/drm/xe/xe_tuning.c | 9 ++++++--- 3 files changed, 22 insertions(+), 3 deletions(-)drivers/gpu/drm/xe/xe_rtp.c +6
-0@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, {return xe_gt_has_discontiguous_dss_groups (gt); } + +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe) +{ +return gt_to_xe (gt)->info.has_flat_ccs; +}drivers/gpu/drm/xe/xe_rtp.h +10
-0@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const struct xe_gt *gt,bool xe_rtp_match_gt_has_discontiguous_dss_groups (const struct xe_gt *gt,const struct xe_hw_engine *hwe); +/** +* xe_rtp_match_has_flat_ccs - Match when platform has FlatCCS compression +* @gt: GT structure +* @hwe: Engine instance +* +* Returns: true if platform has FlatCCS compression, false otherwise +*/ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe); +#endif drivers/gpu/drm/xe/xe_tuning.c +6
-3@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, {XE_RTP_NAME ("Tuning: Compression Overfetch" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (CLR (CCCHKNREG1 ,ENCOMPPERFFIX ),SET (CCCHKNREG1 ,L3CMPCTRL )) },@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = {XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG3 ,COMPPWOVERFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), -XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) },
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Shekhar Chauhan
Reviewed-byRe: [PATCH 21/23] drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
Quoted 31 lines · Matt Roper
Quoted 16 lines · Shekhar Chauhan
Quoted 15 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In
Xe3p_XPC(and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.Note that our
xe_rtp_match_has_flatccs()function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.Quoted 6 lines
Quoted 2 lines
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>The patch in itself looks fine to me, but, the patch doesn't specifically play only around
Xe3p_XPC. Maybe we can move this patch out of the current series, or if we wish to keep it here, can we instead drop thexe3p_xpcfrom the prefix? Thoughts?Aside from PVC (which is Xe1 and not relevant to these tuning settings),
Xe3p_XPCis the only IP we have without FlatCCS in the design, so at the moment this patch is specific toXe3p_XPC. As a general architecture though, if we eventually wind up with other IPs down the road that also lack FlatCCS, then these tuning settings will also not apply to them for the same reasons.
Quoted 1 line
Matt
Okay, makes sense, I'm still skeptical on whether this should be named with the prefix Xe3p_XPC if we expect it to carry it's effect to other future platforms as well. For that reason, I believe, the commit title can be 'drm/xe: Skip compression tuning on platforms without flatccs'. This in itself engulfs Xe3p_XPC (and any other future platforms). But, consider this feedback as only a nitpick.
Since the changes already look good,
Quoted 71 lines
Quoted 71 lines
Quoted 71 lines
--- drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++ drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++ drivers/gpu/drm/xe/xe_tuning.c | 9 ++++++--- 3 files changed, 22 insertions(+), 3 deletions(-)drivers/gpu/drm/xe/xe_rtp.c +6
-0@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, {return xe_gt_has_discontiguous_dss_groups (gt); } + +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe) +{ +return gt_to_xe (gt)->info.has_flat_ccs; +}drivers/gpu/drm/xe/xe_rtp.h +10
-0@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const struct xe_gt *gt,bool xe_rtp_match_gt_has_discontiguous_dss_groups (const struct xe_gt *gt,const struct xe_hw_engine *hwe); +/** +* xe_rtp_match_has_flat_ccs - Match when platform has FlatCCS compression +* @gt: GT structure +* @hwe: Engine instance +* +* Returns: true if platform has FlatCCS compression, false otherwise +*/ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe); +#endif drivers/gpu/drm/xe/xe_tuning.c +6
-3@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, {XE_RTP_NAME ("Tuning: Compression Overfetch" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (CLR (CCCHKNREG1 ,ENCOMPPERFFIX ),SET (CCCHKNREG1 ,L3CMPCTRL )) },@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = {XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG3 ,COMPPWOVERFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), -XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) },
Re: [PATCH 21/23] drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
Quoted 33 lines · Shekhar Chauhan
Quoted 31 lines · Matt Roper
Quoted 16 lines · Shekhar Chauhan
Quoted 15 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In
Xe3p_XPC(and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.Note that our
xe_rtp_match_has_flatccs()function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.Quoted 6 lines
Quoted 2 lines
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>The patch in itself looks fine to me, but, the patch doesn't specifically play only around
Xe3p_XPC. Maybe we can move this patch out of the current series, or if we wish to keep it here, can we instead drop thexe3p_xpcfrom the prefix? Thoughts?Aside from PVC (which is Xe1 and not relevant to these tuning settings),
Xe3p_XPCis the only IP we have without FlatCCS in the design, so at the moment this patch is specific toXe3p_XPC. As a general architecture though, if we eventually wind up with other IPs down the road that also lack FlatCCS, then these tuning settings will also not apply to them for the same reasons.
Quoted 3 lines
Quoted 1 line
Matt
Okay, makes sense, I'm still skeptical on whether this should be named with the prefix
Xe3p_XPCif we expect it to carry it's effect to other future platforms as well. For that reason, I believe, the commit title can be 'drm/xe: Skip compression tuning on platforms without flatccs'.
Makes sense changing it, but I don't mind either way since we are also adding Xe3p_XPC in the same series so it's clear why we are doing so.
Lucas De Marchi
Quoted 77 lines
This in itself engulfs
Xe3p_XPC(and any other future platforms). But, consider this feedback as only a nitpick.Since the changes already look good,
Reviewed-by Shekhar Chauhan <[email protected]>Quoted 71 lines
Quoted 71 lines
Quoted 71 lines
--- drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++ drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++ drivers/gpu/drm/xe/xe_tuning.c | 9 ++++++--- 3 files changed, 22 insertions(+), 3 deletions(-)drivers/gpu/drm/xe/xe_rtp.c +6
-0@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, {return xe_gt_has_discontiguous_dss_groups (gt); } + +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe) +{ +return gt_to_xe (gt)->info.has_flat_ccs; +}drivers/gpu/drm/xe/xe_rtp.h +10
-0@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const struct xe_gt *gt,bool xe_rtp_match_gt_has_discontiguous_dss_groups (const struct xe_gt *gt,const struct xe_hw_engine *hwe); +/** +* xe_rtp_match_has_flat_ccs - Match when platform has FlatCCS compression +* @gt: GT structure +* @hwe: Engine instance +* +* Returns: true if platform has FlatCCS compression, false otherwise +*/ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, +const struct xe_hw_engine *hwe); +#endif drivers/gpu/drm/xe/xe_tuning.c +6
-3@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, {XE_RTP_NAME ("Tuning: Compression Overfetch" ), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (CLR (CCCHKNREG1 ,ENCOMPPERFFIX ),SET (CCCHKNREG1 ,L3CMPCTRL )) },@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = {XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG3 ,COMPPWOVERFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), -XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (GRAPHICS_VERSION_RANGE (2001 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), -XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED )), +XE_RTP_RULES (MEDIA_VERSION_RANGE (2000 ,XE_RTP_END_VERSION_UNDEFINED ), +FUNC (xe_rtp_match_has_flat_ccs)),XE_RTP_ACTIONS (SET (XE2LPM_L3SQCREG2 ,COMPMEMRD256BOVRFETCHEN )) },
Re: [PATCH 21/23] drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs
Quoted 34 lines · Lucas De Marchi
Quoted 33 lines · Shekhar Chauhan
Quoted 31 lines · Matt Roper
Quoted 16 lines · Shekhar Chauhan
Quoted 15 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
The compression overfetch tuning settings only apply to platforms that support FlatCCS. In
Xe3p_XPC(and any future IPs that also lack compression) some of the registers being adjusted by this tuning will not exist or may have been repurposed for something else, so we should take care not to try to program them.Note that our
xe_rtp_match_has_flatccs()function will also return false on platforms that do have FlatCCS in the hardware design, but have compression manually disabled in the BIOS. On such platforms the registers still exist (and it would be fine to continue programming them), but they would have no effect, so skipping that tuning is also safe.Quoted 6 lines
Quoted 2 lines
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>The patch in itself looks fine to me, but, the patch doesn't specifically play only around
Xe3p_XPC. Maybe we can move this patch out of the current series, or if we wish to keep it here, can we instead drop thexe3p_xpcfrom the prefix? Thoughts?Aside from PVC (which is Xe1 and not relevant to these tuning settings),
Xe3p_XPCis the only IP we have without FlatCCS in the design, so at the moment this patch is specific to Xe3p_XPC. As a general architecture though, if we eventually wind up with other IPs down the road that also lack FlatCCS, then these tuning settings will also not apply to them for the same reasons.
Quoted 8 lines
Quoted 3 lines
Quoted 1 line
Matt
Okay, makes sense, I'm still skeptical on whether this should be named with the prefix
Xe3p_XPCif we expect it to carry it's effect to other future platforms as well. For that reason, I believe, the commit title can be 'drm/xe: Skip compression tuning on platforms without flatccs'.Makes sense changing it, but I don't mind either way since we are also adding
Xe3p_XPCin the same series so it's clear why we are doing so.Lucas De Marchi
Alright then, let's keep it this way.
-shekhar
Quoted 90 lines
Quoted 90 lines
This in itself engulfs
Xe3p_XPC(and any other future platforms). But, consider this feedback as only a nitpick.Since the changes already look good,
Reviewed-by Shekhar Chauhan <[email protected]>Quoted 83 lines
Quoted 83 lines
Quoted 83 lines
---
drivers/gpu/drm/xe/xe_rtp.c | 6 ++++++
drivers/gpu/drm/xe/xe_rtp.h | 10 ++++++++++
drivers/gpu/drm/xe/xe_tuning.c| 9 ++++++---3 files changed, 22 insertions(+), 3 deletions(-)drivers/gpu/drm/xe/xe_rtp.c +0
-0@@ -376,3 +376,9 @@ bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, { return xe_gt_has_discontiguous_dss_groups(gt);}
drivers/gpu/drm/xe/xe_rtp.c +6
-0+ +bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, + const struct xe_hw_engine *hwe) +{ + return gt_to_xe(gt)->info.has_flat_ccs; +}drivers/gpu/drm/xe/xe_rtp.h +2
-0@@ -483,4 +483,14 @@ bool xe_rtp_match_psmi_enabled(const structxe_gt *gt, bool xe_rtp_match_gt_has_discontiguous_dss_groups(const struct xe_gt *gt, const struct xe_hw_engine *hwe); +/** +* xe_rtp_match_has_flat_ccs - Match when platform has FlatCCS compression
+ * @gt: GT structure
+ * @hwe: Engine instance
+ *
+ * Returns: true if platform has FlatCCS compression, false otherwise
+ */drivers/gpu/drm/xe/xe_rtp.h +3
-0+bool xe_rtp_match_has_flat_ccs (const struct xe_gt *gt, + const struct xe_hw_engine *hwe); +#endif
drivers/gpu/drm/xe/xe_tuning.c +2
-1@@ -40,7 +40,8 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { REG_FIELD_PREP(L3_PWM_TIMER_INIT_VAL_MASK, 0x7f))) }, { XE_RTP_NAME("Tuning: Compression Overfetch"), - XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED)), + XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED), + FUNC(xe_rtp_match_has_flat_ccs)),
XE_RTP_ACTIONS(CLR(CCCHKNREG1, ENCOMPPERFFIX), SET(CCCHKNREG1, L3CMPCTRL))
},drivers/gpu/drm/xe/xe_tuning.c +2
-2@@ -58,12 +59,14 @@ static const struct xe_rtp_entry_sr gt_tunings[] = { XE_RTP_ACTIONS(SET(XE2LPM_L3SQCREG3, COMPPWOVERFETCHEN)) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only"), - XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED)), + XE_RTP_RULES(GRAPHICS_VERSION_RANGE(2001, XE_RTP_END_VERSION_UNDEFINED), + FUNC(xe_rtp_match_has_flat_ccs)), XE_RTP_ACTIONS(SET(L3SQCREG2, COMPMEMRD256BOVRFETCHEN)) }, { XE_RTP_NAME("Tuning: L2 Overfetch Compressible Only - media"), - XE_RTP_RULES(MEDIA_VERSION_RANGE(2000,
XE_RTP_END_VERSION_UNDEFINED)),
+ XE_RTP_RULES(MEDIA_VERSION_RANGE(2000,XE_RTP_END_VERSION_UNDEFINED),
+FUNC(xe_rtp_match_has_flat_ccs)),
XE_RTP_ACTIONS(SET(XE2LPM_L3SQCREG2,
COMPMEMRD256BOVRFETCHEN))
},
PATCH 22/23 drm/xe/xe3p_xpc: Setup PAT table
In reply to Lucas De MarchiFrom: Matt Roper <[email protected]>
Xe3p_XPC IP requires a new PAT table; note that this table has one fewer column than the Xe2/Xe3 tables since compression is not supported. There's also no "WT" entry (which we wouldn't have used on a platform without display anyway).
Bspec: 71582
--- drivers/gpu/drm/xe/xe_pat.c | 96 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 95 insertions(+), 1 deletion(-)
drivers/gpu/drm/xe/xe_pat.c +95 -1
@@ -154,6 +154,41 @@ static const struct xe_pat_table_entry xe2_pat_table[] = {static const struct xe_pat_table_entry xe2_pat_ats =XE2_PAT (0 ,0 ,0 ,0 ,3 ,3 );static const struct xe_pat_table_entry xe2_pat_pta =XE2_PAT (0 ,0 ,0 ,0 ,3 ,0 ); +/* +* Xe3p_XPC PAT table uses the same layout as Xe2/Xe3, except that there's no +* option for compression. Also note that the "L3" and "L4" register fields +* actually control L2 and L3 cache respectively on this platform. +*/ +#define XE3P_XPC_PAT (no_promote, l3clos, l3_policy, l4_policy, __coh_mode) \ + XE2_PAT(no_promote, 0, l3clos, l3_policy, l4_policy, __coh_mode) + +static const struct xe_pat_table_entry xe3p_xpc_pat_ats =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,3 ); +static const struct xe_pat_table_entry xe3p_xpc_pat_pta =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,0 ); + +static const struct xe_pat_table_entry xe3p_xpc_pat_table[] = { + [0 ] =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,0 ), + [1 ] =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,2 ), + [2 ] =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,3 ), + [3 ] =XE3P_XPC_PAT (0 ,0 ,3 ,3 ,0 ), + [4 ] =XE3P_XPC_PAT (0 ,0 ,3 ,3 ,2 ), + [5 ] =XE3P_XPC_PAT (0 ,0 ,3 ,0 ,0 ), + [6 ] =XE3P_XPC_PAT (0 ,0 ,3 ,0 ,2 ), + [7 ] =XE3P_XPC_PAT (0 ,0 ,3 ,0 ,3 ), + [8 ] =XE3P_XPC_PAT (0 ,0 ,0 ,3 ,0 ), + [9 ] =XE3P_XPC_PAT (0 ,0 ,0 ,3 ,2 ), + [10 ] =XE3P_XPC_PAT (0 ,0 ,0 ,3 ,3 ), +/* 11..22 are reserved; leave set to all 0's */ + [23 ] =XE3P_XPC_PAT (0 ,1 ,0 ,0 ,0 ), + [24 ] =XE3P_XPC_PAT (0 ,1 ,0 ,0 ,2 ), + [25 ] =XE3P_XPC_PAT (0 ,1 ,0 ,0 ,3 ), + [26 ] =XE3P_XPC_PAT (0 ,2 ,0 ,0 ,0 ), + [27 ] =XE3P_XPC_PAT (0 ,2 ,0 ,0 ,2 ), + [28 ] =XE3P_XPC_PAT (0 ,2 ,0 ,0 ,3 ), + [29 ] =XE3P_XPC_PAT (0 ,3 ,0 ,0 ,0 ), + [30 ] =XE3P_XPC_PAT (0 ,3 ,0 ,0 ,2 ), + [31 ] =XE3P_XPC_PAT (0 ,3 ,0 ,0 ,3 ), +}; +u16 xe_pat_index_get_coh_mode (struct xe_device *xe,u16 pat_index) {WARN_ON (pat_index >= xe->pat.n_entries);
@@ -380,9 +415,68 @@ static const struct xe_pat_ops xe2_pat_ops = { .dump = xe2_dump, }; +static int xe3p_xpc_dump (struct xe_gt *gt,struct drm_printer *p) +{ +struct xe_device *xe =gt_to_xe (gt); +unsigned int fw_ref; +u32 pat; +int i; + + fw_ref =xe_force_wake_get (gt_to_fw (gt),XE_FW_GT ); +if (!fw_ref) +return -ETIMEDOUT ; + +drm_printf (p,"PAT table:\n" ); + +for (i =0 ; i < xe->pat.n_entries; i++) { + pat =xe_gt_mcr_unicast_read_any (gt,XE_REG_MCR (_PAT_INDEX (i))); + +drm_printf (p,"PAT[%2d] = [ %u, %u, %u, %u, %u ] (%#8x)\n" , i, + !!(pat &XE2_NO_PROMOTE ), +REG_FIELD_GET (XE2_L3_CLOS , pat), +REG_FIELD_GET (XE2_L3_POLICY , pat), +REG_FIELD_GET (XE2_L4_POLICY , pat), +REG_FIELD_GET (XE2_COH_MODE , pat), + pat); + } + +/* +* Also print PTA_MODE, which describes how the hardware accesses +* PPGTT entries. +*/ + pat =xe_gt_mcr_unicast_read_any (gt,XE_REG_MCR (_PAT_PTA)); + +drm_printf (p,"Page Table Access:\n" ); +drm_printf (p,"PTA_MODE= [ %u, %u, %u, %u, %u ] (%#8x)\n" , + !!(pat &XE2_NO_PROMOTE ), +REG_FIELD_GET (XE2_L3_CLOS , pat), +REG_FIELD_GET (XE2_L3_POLICY , pat), +REG_FIELD_GET (XE2_L4_POLICY , pat), +REG_FIELD_GET (XE2_COH_MODE , pat), + pat); + +xe_force_wake_put (gt_to_fw (gt), fw_ref); +return 0 ; +} + +static const struct xe_pat_ops xe3p_xpc_pat_ops = { + .program_graphics = program_pat_mcr, + .program_media = program_pat, + .dump = xe3p_xpc_dump, +}; +void xe_pat_init_early (struct xe_device *xe) { -if (GRAPHICS_VER (xe) ==30 ||GRAPHICS_VER (xe) ==20 ) { +if (GRAPHICS_VERx100 (xe) ==3511 ) { + xe->pat.ops = &xe3p_xpc_pat_ops; + xe->pat.table = xe3p_xpc_pat_table; + xe->pat.pat_ats = &xe3p_xpc_pat_ats; + xe->pat.pat_pta = &xe3p_xpc_pat_pta; + xe->pat.n_entries =ARRAY_SIZE (xe3p_xpc_pat_table); + xe->pat.idx[XE_CACHE_NONE ] =3 ; + xe->pat.idx[XE_CACHE_WT ] =3 ;/* N/A (no display); use UC */ + xe->pat.idx[XE_CACHE_WB ] =2 ; + }else if (GRAPHICS_VER (xe) ==30 ||GRAPHICS_VER (xe) ==20 ) { xe->pat.ops = &xe2_pat_ops; xe->pat.table = xe2_pat_table; xe->pat.pat_ats = &xe2_pat_ats;
Signature · 1 line
2.51.0
Re: [PATCH 22/23] drm/xe/xe3p_xpc: Setup PAT table
Quoted 93 lines · Lucas De Marchi
From: Matt Roper <[email protected]>
Xe3p_XPCIP requires a new PAT table; note that this table has one fewer column than the Xe2/Xe3 tables since compression is not supported. There's also no "WT" entry (which we wouldn't have used on a platform without display anyway).Bspec: 71582
Signed-off-by Matt Roper <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_pat.c | 96 ++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 95 insertions(+), 1 deletion(-)drivers/gpu/drm/xe/xe_pat.c +64
-0@@ -154,6 +154,41 @@ static const struct xe_pat_table_entry xe2_pat_table[] = {static const struct xe_pat_table_entry xe2_pat_ats =XE2_PAT (0 ,0 ,0 ,0 ,3 ,3 );static const struct xe_pat_table_entry xe2_pat_pta =XE2_PAT (0 ,0 ,0 ,0 ,3 ,0 ); +/* +* Xe3p_XPC PAT table uses the same layout as Xe2/Xe3, except that there's no +* option for compression. Also note that the "L3" and "L4" register fields +* actually control L2 and L3 cache respectively on this platform. +*/ +#define XE3P_XPC_PAT (no_promote, l3clos, l3_policy, l4_policy, __coh_mode) \ + XE2_PAT(no_promote, 0, l3clos, l3_policy, l4_policy, __coh_mode) + +static const struct xe_pat_table_entry xe3p_xpc_pat_ats =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,3 ); +static const struct xe_pat_table_entry xe3p_xpc_pat_pta =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,0 ); + +static const struct xe_pat_table_entry xe3p_xpc_pat_table[] = { + [0 ] =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,0 ), + [1 ] =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,2 ), + [2 ] =XE3P_XPC_PAT (0 ,0 ,0 ,0 ,3 ), + [3 ] =XE3P_XPC_PAT (0 ,0 ,3 ,3 ,0 ), + [4 ] =XE3P_XPC_PAT (0 ,0 ,3 ,3 ,2 ), + [5 ] =XE3P_XPC_PAT (0 ,0 ,3 ,0 ,0 ), + [6 ] =XE3P_XPC_PAT (0 ,0 ,3 ,0 ,2 ), + [7 ] =XE3P_XPC_PAT (0 ,0 ,3 ,0 ,3 ), + [8 ] =XE3P_XPC_PAT (0 ,0 ,0 ,3 ,0 ), + [9 ] =XE3P_XPC_PAT (0 ,0 ,0 ,3 ,2 ), + [10 ] =XE3P_XPC_PAT (0 ,0 ,0 ,3 ,3 ), +/* 11..22 are reserved; leave set to all 0's */ + [23 ] =XE3P_XPC_PAT (0 ,1 ,0 ,0 ,0 ), + [24 ] =XE3P_XPC_PAT (0 ,1 ,0 ,0 ,2 ), + [25 ] =XE3P_XPC_PAT (0 ,1 ,0 ,0 ,3 ), + [26 ] =XE3P_XPC_PAT (0 ,2 ,0 ,0 ,0 ), + [27 ] =XE3P_XPC_PAT (0 ,2 ,0 ,0 ,2 ), + [28 ] =XE3P_XPC_PAT (0 ,2 ,0 ,0 ,3 ), + [29 ] =XE3P_XPC_PAT (0 ,3 ,0 ,0 ,0 ), + [30 ] =XE3P_XPC_PAT (0 ,3 ,0 ,0 ,2 ), + [31 ] =XE3P_XPC_PAT (0 ,3 ,0 ,0 ,3 ), +}; +u16 xe_pat_index_get_coh_mode (struct xe_device *xe,u16 pat_index) {WARN_ON (pat_index >= xe->pat.n_entries);@@ -380,9 +415,68 @@ static const struct xe_pat_ops xe2_pat_ops = { .dump = xe2_dump, }; +static int xe3p_xpc_dump (struct xe_gt *gt,struct drm_printer *p) +{ +struct xe_device *xe =gt_to_xe (gt); +unsigned int fw_ref; +u32 pat; +int i; + + fw_ref =xe_force_wake_get (gt_to_fw (gt),XE_FW_GT ); +if (!fw_ref) +return -ETIMEDOUT ; + +drm_printf (p,"PAT table:\n" ); + +for (i =0 ; i < xe->pat.n_entries; i++) { + pat =xe_gt_mcr_unicast_read_any (gt,XE_REG_MCR (_PAT_INDEX (i))); + +drm_printf (p,"PAT[%2d] = [ %u, %u, %u, %u, %u ] (%#8x)\n" , i, + !!(pat &XE2_NO_PROMOTE ), +REG_FIELD_GET (XE2_L3_CLOS , pat), +REG_FIELD_GET (XE2_L3_POLICY , pat), +REG_FIELD_GET (XE2_L4_POLICY , pat), +REG_FIELD_GET (XE2_COH_MODE , pat), + pat); + } + +/* +* Also print PTA_MODE, which describes how the hardware accesses +* PPGTT entries. +*/
drivers/gpu/drm/xe/xe_pat.c static const struct xe_pat_ops xe2_pat_ops = { · line 456
Quoted 10 lines
drivers/gpu/drm/xe/xe_pat.c +10
-0+ pat =xe_gt_mcr_unicast_read_any (gt,XE_REG_MCR (_PAT_PTA)); + +drm_printf (p,"Page Table Access:\n" ); +drm_printf (p,"PTA_MODE= [ %u, %u, %u, %u, %u ] (%#8x)\n" , + !!(pat &XE2_NO_PROMOTE ), +REG_FIELD_GET (XE2_L3_CLOS , pat), +REG_FIELD_GET (XE2_L3_POLICY , pat), +REG_FIELD_GET (XE2_L4_POLICY , pat), +REG_FIELD_GET (XE2_COH_MODE , pat), + pat);
For completeness, we can print the _PTA_ATS register also. Outside that, patch LGTM.
Quoted 31 lines
drivers/gpu/drm/xe/xe_pat.c +21
-1+ +xe_force_wake_put (gt_to_fw (gt), fw_ref); +return 0 ; +} + +static const struct xe_pat_ops xe3p_xpc_pat_ops = { + .program_graphics = program_pat_mcr, + .program_media = program_pat, + .dump = xe3p_xpc_dump, +}; +void xe_pat_init_early (struct xe_device *xe) { -if (GRAPHICS_VER (xe) ==30 ||GRAPHICS_VER (xe) ==20 ) { +if (GRAPHICS_VERx100 (xe) ==3511 ) { + xe->pat.ops = &xe3p_xpc_pat_ops; + xe->pat.table = xe3p_xpc_pat_table; + xe->pat.pat_ats = &xe3p_xpc_pat_ats; + xe->pat.pat_pta = &xe3p_xpc_pat_pta; + xe->pat.n_entries =ARRAY_SIZE (xe3p_xpc_pat_table); + xe->pat.idx[XE_CACHE_NONE ] =3 ; + xe->pat.idx[XE_CACHE_WT ] =3 ;/* N/A (no display); use UC */ + xe->pat.idx[XE_CACHE_WB ] =2 ; + }else if (GRAPHICS_VER (xe) ==30 ||GRAPHICS_VER (xe) ==20 ) { xe->pat.ops = &xe2_pat_ops; xe->pat.table = xe2_pat_table; xe->pat.pat_ats = &xe2_pat_ats;Signature · 2 lines
-- 2.51.0
PATCH 23/23 drm/xe/xe3p: Add xe3p EU stall data format
In reply to Lucas De MarchiFrom: Harish Chegondi <[email protected]>
Starting with Xe3p, IP address in EU stall data is increases to 61 bits.
--- drivers/gpu/drm/xe/xe_eu_stall.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
drivers/gpu/drm/xe/xe_eu_stall.c +23 -0
@@ -124,6 +124,27 @@ struct xe_eu_stall_data_xe2 {__u64 unused[6 ]; } __packed; +/* +* EU stall data format for Xe3p arch GPUs. +*/ +struct xe_eu_stall_data_xe3p { +__u64 ip_addr:61 ;/* Bits 0 to 60 */ +__u64 tdr_count:8 ;/* Bits 61 to 68 */ +__u64 other_count:8 ;/* Bits 69 to 76 */ +__u64 control_count:8 ;/* Bits 77 to 84 */ +__u64 pipestall_count:8 ;/* Bits 85 to 92 */ +__u64 send_count:8 ;/* Bits 93 to 100 */ +__u64 dist_acc_count:8 ;/* Bits 101 to 108 */ +__u64 sbid_count:8 ;/* Bits 109 to 116 */ +__u64 sync_count:8 ;/* Bits 117 to 124 */ +__u64 inst_fetch_count:8 ;/* Bits 125 to 132 */ +__u64 active_count:8 ;/* Bits 133 to 140 */ +__u64 ex_id:3 ;/* Bits 141 to 143 */ +__u64 end_flag:1 ;/* Bit 144 */ +__u64 unused_bits:47 ; +__u64 unused[5 ]; +} __packed; +const u64 eu_stall_sampling_rates[] = {251 ,251 *2 ,251 *3 ,251 *4 ,251 *5 ,251 *6 ,251 *7 };/**
@@ -169,6 +190,8 @@ size_t xe_eu_stall_data_record_size(struct xe_device *xe)if (xe->info.platform ==XE_PVC ) record_size =sizeof (struct xe_eu_stall_data_pvc ); +else if (GRAPHICS_VER (xe) >=35 ) + record_size =sizeof (struct xe_eu_stall_data_xe3p );else if (GRAPHICS_VER (xe) >=20 ) record_size =sizeof (struct xe_eu_stall_data_xe2 );
Signature · 1 line
2.51.0
Re: [PATCH 23/23] drm/xe/xe3p: Add xe3p EU stall data format
Quoted 3 lines · Lucas De Marchi
From: Harish Chegondi <[email protected]>
Starting with Xe3p, IP address in EU stall data is increases to 61 bits.
As far as I can see, the EU stall format isn't documented anywhere in the bspec (which seems like a major oversight!) but the early architecture document related to this change seems to indicate that a full 64-bit IP was supposed to be written by hardware now
"Bit filed[sic] 0-28 is now 0-63"
Your structure is only using 61 bits (which definitely makes sense if the addresses are aligned since the lowest three bits would always be 0's); is there somewhere other than the bspec or architecture document that we should be looking at to confirm this?
If you've been working directly with the hardware architects on this feature, please poke them about documenting this clearly in the bspec (with proper tagging by IP/platform) so that we can verify this is handled correctly and also notice if/when the format changes again on future platforms.
Matt
Quoted 53 lines
Cc Ashutosh Dixit <[email protected]>Signed-off-by Harish Chegondi <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_eu_stall.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)drivers/gpu/drm/xe/xe_eu_stall.c +23
-0@@ -124,6 +124,27 @@ struct xe_eu_stall_data_xe2 {__u64 unused[6 ]; } __packed; +/* +* EU stall data format for Xe3p arch GPUs. +*/ +struct xe_eu_stall_data_xe3p { +__u64 ip_addr:61 ;/* Bits 0 to 60 */ +__u64 tdr_count:8 ;/* Bits 61 to 68 */ +__u64 other_count:8 ;/* Bits 69 to 76 */ +__u64 control_count:8 ;/* Bits 77 to 84 */ +__u64 pipestall_count:8 ;/* Bits 85 to 92 */ +__u64 send_count:8 ;/* Bits 93 to 100 */ +__u64 dist_acc_count:8 ;/* Bits 101 to 108 */ +__u64 sbid_count:8 ;/* Bits 109 to 116 */ +__u64 sync_count:8 ;/* Bits 117 to 124 */ +__u64 inst_fetch_count:8 ;/* Bits 125 to 132 */ +__u64 active_count:8 ;/* Bits 133 to 140 */ +__u64 ex_id:3 ;/* Bits 141 to 143 */ +__u64 end_flag:1 ;/* Bit 144 */ +__u64 unused_bits:47 ; +__u64 unused[5 ]; +} __packed; +const u64 eu_stall_sampling_rates[] = {251 ,251 *2 ,251 *3 ,251 *4 ,251 *5 ,251 *6 ,251 *7 };/** @@ -169,6 +190,8 @@ size_t xe_eu_stall_data_record_size(struct xe_device *xe)if (xe->info.platform ==XE_PVC ) record_size =sizeof (struct xe_eu_stall_data_pvc ); +else if (GRAPHICS_VER (xe) >=35 ) + record_size =sizeof (struct xe_eu_stall_data_xe3p );else if (GRAPHICS_VER (xe) >=20 ) record_size =sizeof (struct xe_eu_stall_data_xe2 );Signature · 2 lines
-- 2.51.0
Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Re: [PATCH 23/23] drm/xe/xe3p: Add xe3p EU stall data format
Quoted 10 lines · Matt Roper
Quoted 3 lines · Lucas De Marchi
From: Harish Chegondi <[email protected]>
Starting with Xe3p, IP address in EU stall data is increases to 61 bits.
As far as I can see, the EU stall format isn't documented anywhere in the bspec (which seems like a major oversight!) but the early architecture document related to this change seems to indicate that a full 64-bit IP was supposed to be written by hardware now
Quoted 6 lines
"Bit filed[sic] 0-28 is now 0-63"Your structure is only using 61 bits (which definitely makes sense if the addresses are aligned since the lowest three bits would always be 0's); is there somewhere other than the bspec or architecture document that we should be looking at to confirm this?
I agree that EU stall is not properly documented in the B-Spec. I looked up an HSD for Xe3p to confirm and make this change. Also checked with the architect to confirm this change.
Quoted 6 lines
If you've been working directly with the hardware architects on this feature, please poke them about documenting this clearly in the bspec (with proper tagging by IP/platform) so that we can verify this is handled correctly and also notice if/when the format changes again on future platforms.
Sure, I will follow up with the HW architects to make sure the EU stall data formats are properly documented in the Bspec and are properly tagged.
Quoted 3 lines
Matt
Thank You
Harish.
Quoted 60 lines
Quoted 54 lines
Cc Ashutosh Dixit <[email protected]>Signed-off-by Harish Chegondi <[email protected]>Signed-off-by Lucas De Marchi <[email protected]>--- drivers/gpu/drm/xe/xe_eu_stall.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)drivers/gpu/drm/xe/xe_eu_stall.c +23
-0@@ -124,6 +124,27 @@ struct xe_eu_stall_data_xe2 {__u64 unused[6 ]; } __packed; +/* +* EU stall data format for Xe3p arch GPUs. +*/ +struct xe_eu_stall_data_xe3p { +__u64 ip_addr:61 ;/* Bits 0 to 60 */ +__u64 tdr_count:8 ;/* Bits 61 to 68 */ +__u64 other_count:8 ;/* Bits 69 to 76 */ +__u64 control_count:8 ;/* Bits 77 to 84 */ +__u64 pipestall_count:8 ;/* Bits 85 to 92 */ +__u64 send_count:8 ;/* Bits 93 to 100 */ +__u64 dist_acc_count:8 ;/* Bits 101 to 108 */ +__u64 sbid_count:8 ;/* Bits 109 to 116 */ +__u64 sync_count:8 ;/* Bits 117 to 124 */ +__u64 inst_fetch_count:8 ;/* Bits 125 to 132 */ +__u64 active_count:8 ;/* Bits 133 to 140 */ +__u64 ex_id:3 ;/* Bits 141 to 143 */ +__u64 end_flag:1 ;/* Bit 144 */ +__u64 unused_bits:47 ; +__u64 unused[5 ]; +} __packed; +const u64 eu_stall_sampling_rates[] = {251 ,251 *2 ,251 *3 ,251 *4 ,251 *5 ,251 *6 ,251 *7 };/** @@ -169,6 +190,8 @@ size_t xe_eu_stall_data_record_size(struct xe_device *xe)if (xe->info.platform ==XE_PVC ) record_size =sizeof (struct xe_eu_stall_data_pvc ); +else if (GRAPHICS_VER (xe) >=35 ) + record_size =sizeof (struct xe_eu_stall_data_xe3p );else if (GRAPHICS_VER (xe) >=20 ) record_size =sizeof (struct xe_eu_stall_data_xe2 );Signature · 2 lines
-- 2.51.0Signature · 4 lines
Matt Roper Graphics Software Engineer Linux GPU Platform Enablement Intel Corporation
Patchwork
CI✗ CI.checkpatch: warning for drm/xe: Add Xe3p support
In reply to Lucas De Marchi== Series Details ==
== Series Details ==
Series: drm/xe: Add Xe3p support
URL : https://patchwork.freedesktop.org/series/155866/
State : warning
== Summary ==
+ KERNEL=/kernel
+ git clone https://gitlab.freedesktop.org/drm/maintainer-tools mt Cloning into 'mt'...
warning: redirecting to https://gitlab.freedesktop.org/drm/maintainer-tools.git/
+ git -C mt rev-list -n1 origin/master fbd08a78c3a3bb17964db2a326514c69c1dca660
+ cd /kernel
+ git config --global --add safe.directory /kernel
+ git log -n1
commit fd8bc35abbfa6f3960c9366a516c9b8611cb822c
Author: Harish Chegondi <[email protected]> Date: Mon Oct 13 20:24:55 2025 -0700
drm/xe/xe3p: Add xe3p EU stall data format
Starting with Xe3p, IP address in EU stall data is increases to 61 bits.
+ /mt/dim checkpatch c917f7d11493984be9f381ca0a7667bd3e587ada drm-intel e4dc57b8acaa drm/xe/xe3: Add support for graphics IP versions 30.04 & 30.05 -:46: WARNING:LONG_LINE: line length of 103 exceeds 100 columns #46: FILE: drivers/gpu/drm/xe/xe_wa.c:698:
+ XE_RTP_RULES(GRAPHICS_VERSION_RANGE(3003, 3005), FUNC(xe_rtp_match_first_render_or_compute)),
total: 0 errors, 1 warnings, 0 checks, 62 lines checked28da2adfdb2a drm/xe/xe3p_lpm: Add support for media IP versions 35.00 & 35.03 7c039973bd65 drm/xe/xe3p_lpm: Configure MAIN_GAMCTRL_QUEUE_SELECT f30f780eeb7b drm/xe/xe3p_lpm: Add special check in Media GT for Main GAMCTRL 075fc1a523e1 drm/xe/xe3p_lpm: Stop reading the CTC_MODE register 53adff75d0eb drm/xe/xe3p_lpm: Skip disabling NOA on unsupported IPs ad2b7408d4c4 drm/xe/xe3p_lpm: Handle MCR steering1024935e0655 drm/xe/xe3p: Stop programming RCU_MODE's fixed slice mode setting 8014535b7fb1 drm/xe/xe3p: Determine service copy availability from fuse 3a5ce27e4041 drm/xe/xe3p: Skip TD flushf81700a35eaf drm/xe/xe3p: Enable L2 flush optimization feature 74d12f42e7e4 drm/xe/xe3p: Flush userptr/shrinker bo cachelines manually c71b2b3bd222 drm/xe: Dump CURRENT_LRCA and CSMQDEBUG registers 9ca0a0e9cd51 drm/xe/nvl: Define NVL-S platform
-:59: ERROR:COMPLEX_MACRO: Macros with complex values should be enclosed in parentheses #59: FILE: include/drm/intel/pciids.h:888:
+#define INTEL_NVLS_IDS(MACRO__, ...) \
+ MACRO__(0xD740, ## __VA_ARGS__), \
+ MACRO__(0xD741, ## __VA_ARGS__), \
+ MACRO__(0xD742, ## __VA_ARGS__), \
+ MACRO__(0xD743, ## __VA_ARGS__), \
+ MACRO__(0xD744, ## __VA_ARGS__), \
+ MACRO__(0xD745, ## __VA_ARGS__)
BUT SEE:
do {} while (0) advice is over-stated in a few situations:
The more obvious case is macros, like MODULE_PARM_DESC, invoked at file-scope, where C disallows code (it must be in functions). See $exceptions if you have one to add by name.
More troublesome is declarative macros used at top of new scope, like DECLARE_PER_CPU. These might just compile with a do-while-0 wrapper, but would be incorrect. Most of these are handled by detecting struct,union,etc declaration primitives in $exceptions.
Theres also macros called inside an if (block), which "return" an expression. These cannot do-while, and need a ({}) wrapper.
Enjoy this qualification while we work to improve our heuristics.
-:59: CHECK:MACRO_ARG_REUSE: Macro argument reuse 'MACRO__' - possible side-effects? #59: FILE: include/drm/intel/pciids.h:888:
+#define INTEL_NVLS_IDS(MACRO__, ...) \
+ MACRO__(0xD740, ## __VA_ARGS__), \
+ MACRO__(0xD741, ## __VA_ARGS__), \
+ MACRO__(0xD742, ## __VA_ARGS__), \
+ MACRO__(0xD743, ## __VA_ARGS__), \
+ MACRO__(0xD744, ## __VA_ARGS__), \
+ MACRO__(0xD745, ## __VA_ARGS__)
total: 1 errors, 0 warnings, 1 checks, 41 lines checked bdba729d0a2a drm/xe/nvls: Define GuC firmware for NVL-S 29ad48fc7722 drm/xe/nvls: Attach MOCS table for NVL-S14a24644d423 drm/xe/xe3p_xpc: Add Xe3p_XPC IP definition 7eb51f6706c4 drm/xe/xe3p_xpc: Add L3 bank mask1fb93893a954 drm/xe/xe3p_xpc: Add MCR steeringa098f6e31d13 drm/xe/xe3p_xpc: Add support for compute walker for non-MSIx -:8: WARNING:TYPO_SPELLING: 'interrup' may be misspelled - perhaps 'interrupt'? #8:PIPE_CONTROL interrup was done. This created latency on SW stack.
^^^^^^^^
total: 0 errors, 1 warnings, 0 checks, 17 lines checkede19928035d13 drm/xe/xe3p_xpc: Skip compression tuning on platforms without flatccs -:33: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis #33: FILE: drivers/gpu/drm/xe/xe_rtp.c:381:
+bool xe_rtp_match_has_flat_ccs(const struct xe_gt *gt,
+ const struct xe_hw_engine *hwe)
total: 0 errors, 0 warnings, 1 checks, 48 lines checkedb5b5435b3ac9 drm/xe/xe3p_xpc: Setup PAT table
-:31: ERROR:SPACING: space prohibited after that open parenthesis '('
#31: FILE: drivers/gpu/drm/xe/xe_pat.c:165:
+static const struct xe_pat_table_entry xe3p_xpc_pat_ats = XE3P_XPC_PAT( 0, 0, 0, 0, 3 );
-:31: ERROR:SPACING: space prohibited before that close parenthesis ')' #31: FILE: drivers/gpu/drm/xe/xe_pat.c:165:
+static const struct xe_pat_table_entry xe3p_xpc_pat_ats = XE3P_XPC_PAT( 0, 0, 0, 0, 3 );
-:32: ERROR:SPACING: space prohibited after that open parenthesis '('
#32: FILE: drivers/gpu/drm/xe/xe_pat.c:166:
+static const struct xe_pat_table_entry xe3p_xpc_pat_pta = XE3P_XPC_PAT( 0, 0, 0, 0, 0 );
-:32: ERROR:SPACING: space prohibited before that close parenthesis ')' #32: FILE: drivers/gpu/drm/xe/xe_pat.c:166:
+static const struct xe_pat_table_entry xe3p_xpc_pat_pta = XE3P_XPC_PAT( 0, 0, 0, 0, 0 );
-:35: ERROR:SPACING: space prohibited after that open square bracket '[' #35: FILE: drivers/gpu/drm/xe/xe_pat.c:169:
+ [ 0] = XE3P_XPC_PAT( 0, 0, 0, 0, 0 ),
-:35: ERROR:SPACING: space prohibited after that open parenthesis '(' #35: FILE: drivers/gpu/drm/xe/xe_pat.c:169:
+ [ 0] = XE3P_XPC_PAT( 0, 0, 0, 0, 0 ),
-:35: ERROR:SPACING: space prohibited before that close parenthesis ')' #35: FILE: drivers/gpu/drm/xe/xe_pat.c:169:
+ [ 0] = XE3P_XPC_PAT( 0, 0, 0, 0, 0 ),
-:36: ERROR:SPACING: space prohibited after that open square bracket '[' #36: FILE: drivers/gpu/drm/xe/xe_pat.c:170:
+ [ 1] = XE3P_XPC_PAT( 0, 0, 0, 0, 2 ),
-:36: ERROR:SPACING: space prohibited after that open parenthesis '(' #36: FILE: drivers/gpu/drm/xe/xe_pat.c:170:
+ [ 1] = XE3P_XPC_PAT( 0, 0, 0, 0, 2 ),
-:36: ERROR:SPACING: space prohibited before that close parenthesis ')' #36: FILE: drivers/gpu/drm/xe/xe_pat.c:170:
+ [ 1] = XE3P_XPC_PAT( 0, 0, 0, 0, 2 ),
-:37: ERROR:SPACING: space prohibited after that open square bracket '[' #37: FILE: drivers/gpu/drm/xe/xe_pat.c:171:
+ [ 2] = XE3P_XPC_PAT( 0, 0, 0, 0, 3 ),
-:37: ERROR:SPACING: space prohibited after that open parenthesis '(' #37: FILE: drivers/gpu/drm/xe/xe_pat.c:171:
+ [ 2] = XE3P_XPC_PAT( 0, 0, 0, 0, 3 ),
-:37: ERROR:SPACING: space prohibited before that close parenthesis ')' #37: FILE: drivers/gpu/drm/xe/xe_pat.c:171:
+ [ 2] = XE3P_XPC_PAT( 0, 0, 0, 0, 3 ),
-:38: ERROR:SPACING: space prohibited after that open square bracket '[' #38: FILE: drivers/gpu/drm/xe/xe_pat.c:172:
+ [ 3] = XE3P_XPC_PAT( 0, 0, 3, 3, 0 ),
-:38: ERROR:SPACING: space prohibited after that open parenthesis '(' #38: FILE: drivers/gpu/drm/xe/xe_pat.c:172:
+ [ 3] = XE3P_XPC_PAT( 0, 0, 3, 3, 0 ),
-:38: ERROR:SPACING: space prohibited before that close parenthesis ')' #38: FILE: drivers/gpu/drm/xe/xe_pat.c:172:
+ [ 3] = XE3P_XPC_PAT( 0, 0, 3, 3, 0 ),
-:39: ERROR:SPACING: space prohibited after that open square bracket '[' #39: FILE: drivers/gpu/drm/xe/xe_pat.c:173:
+ [ 4] = XE3P_XPC_PAT( 0, 0, 3, 3, 2 ),
-:39: ERROR:SPACING: space prohibited after that open parenthesis '(' #39: FILE: drivers/gpu/drm/xe/xe_pat.c:173:
+ [ 4] = XE3P_XPC_PAT( 0, 0, 3, 3, 2 ),
-:39: ERROR:SPACING: space prohibited before that close parenthesis ')' #39: FILE: drivers/gpu/drm/xe/xe_pat.c:173:
+ [ 4] = XE3P_XPC_PAT( 0, 0, 3, 3, 2 ),
-:40: ERROR:SPACING: space prohibited after that open square bracket '[' #40: FILE: drivers/gpu/drm/xe/xe_pat.c:174:
+ [ 5] = XE3P_XPC_PAT( 0, 0, 3, 0, 0 ),
-:40: ERROR:SPACING: space prohibited after that open parenthesis '(' #40: FILE: drivers/gpu/drm/xe/xe_pat.c:174:
+ [ 5] = XE3P_XPC_PAT( 0, 0, 3, 0, 0 ),
-:40: ERROR:SPACING: space prohibited before that close parenthesis ')' #40: FILE: drivers/gpu/drm/xe/xe_pat.c:174:
+ [ 5] = XE3P_XPC_PAT( 0, 0, 3, 0, 0 ),
-:41: ERROR:SPACING: space prohibited after that open square bracket '[' #41: FILE: drivers/gpu/drm/xe/xe_pat.c:175:
+ [ 6] = XE3P_XPC_PAT( 0, 0, 3, 0, 2 ),
-:41: ERROR:SPACING: space prohibited after that open parenthesis '(' #41: FILE: drivers/gpu/drm/xe/xe_pat.c:175:
+ [ 6] = XE3P_XPC_PAT( 0, 0, 3, 0, 2 ),
-:41: ERROR:SPACING: space prohibited before that close parenthesis ')' #41: FILE: drivers/gpu/drm/xe/xe_pat.c:175:
+ [ 6] = XE3P_XPC_PAT( 0, 0, 3, 0, 2 ),
-:42: ERROR:SPACING: space prohibited after that open square bracket '[' #42: FILE: drivers/gpu/drm/xe/xe_pat.c:176:
+ [ 7] = XE3P_XPC_PAT( 0, 0, 3, 0, 3 ),
-:42: ERROR:SPACING: space prohibited after that open parenthesis '(' #42: FILE: drivers/gpu/drm/xe/xe_pat.c:176:
+ [ 7] = XE3P_XPC_PAT( 0, 0, 3, 0, 3 ),
-:42: ERROR:SPACING: space prohibited before that close parenthesis ')' #42: FILE: drivers/gpu/drm/xe/xe_pat.c:176:
+ [ 7] = XE3P_XPC_PAT( 0, 0, 3, 0, 3 ),
-:43: ERROR:SPACING: space prohibited after that open square bracket '[' #43: FILE: drivers/gpu/drm/xe/xe_pat.c:177:
+ [ 8] = XE3P_XPC_PAT( 0, 0, 0, 3, 0 ),
-:43: ERROR:SPACING: space prohibited after that open parenthesis '(' #43: FILE: drivers/gpu/drm/xe/xe_pat.c:177:
+ [ 8] = XE3P_XPC_PAT( 0, 0, 0, 3, 0 ),
-:43: ERROR:SPACING: space prohibited before that close parenthesis ')' #43: FILE: drivers/gpu/drm/xe/xe_pat.c:177:
+ [ 8] = XE3P_XPC_PAT( 0, 0, 0, 3, 0 ),
-:44: ERROR:SPACING: space prohibited after that open square bracket '[' #44: FILE: drivers/gpu/drm/xe/xe_pat.c:178:
+ [ 9] = XE3P_XPC_PAT( 0, 0, 0, 3, 2 ),
-:44: ERROR:SPACING: space prohibited after that open parenthesis '(' #44: FILE: drivers/gpu/drm/xe/xe_pat.c:178:
+ [ 9] = XE3P_XPC_PAT( 0, 0, 0, 3, 2 ),
-:44: ERROR:SPACING: space prohibited before that close parenthesis ')' #44: FILE: drivers/gpu/drm/xe/xe_pat.c:178:
+ [ 9] = XE3P_XPC_PAT( 0, 0, 0, 3, 2 ),
-:45: ERROR:SPACING: space prohibited after that open parenthesis '(' #45: FILE: drivers/gpu/drm/xe/xe_pat.c:179:
+ [10] = XE3P_XPC_PAT( 0, 0, 0, 3, 3 ),
-:45: ERROR:SPACING: space prohibited before that close parenthesis ')' #45: FILE: drivers/gpu/drm/xe/xe_pat.c:179:
+ [10] = XE3P_XPC_PAT( 0, 0, 0, 3, 3 ),
-:47: ERROR:SPACING: space prohibited after that open parenthesis '(' #47: FILE: drivers/gpu/drm/xe/xe_pat.c:181:
+ [23] = XE3P_XPC_PAT( 0, 1, 0, 0, 0 ),
-:47: ERROR:SPACING: space prohibited before that close parenthesis ')' #47: FILE: drivers/gpu/drm/xe/xe_pat.c:181:
+ [23] = XE3P_XPC_PAT( 0, 1, 0, 0, 0 ),
-:48: ERROR:SPACING: space prohibited after that open parenthesis '(' #48: FILE: drivers/gpu/drm/xe/xe_pat.c:182:
+ [24] = XE3P_XPC_PAT( 0, 1, 0, 0, 2 ),
-:48: ERROR:SPACING: space prohibited before that close parenthesis ')' #48: FILE: drivers/gpu/drm/xe/xe_pat.c:182:
+ [24] = XE3P_XPC_PAT( 0, 1, 0, 0, 2 ),
-:49: ERROR:SPACING: space prohibited after that open parenthesis '(' #49: FILE: drivers/gpu/drm/xe/xe_pat.c:183:
+ [25] = XE3P_XPC_PAT( 0, 1, 0, 0, 3 ),
-:49: ERROR:SPACING: space prohibited before that close parenthesis ')' #49: FILE: drivers/gpu/drm/xe/xe_pat.c:183:
+ [25] = XE3P_XPC_PAT( 0, 1, 0, 0, 3 ),
-:50: ERROR:SPACING: space prohibited after that open parenthesis '(' #50: FILE: drivers/gpu/drm/xe/xe_pat.c:184:
+ [26] = XE3P_XPC_PAT( 0, 2, 0, 0, 0 ),
-:50: ERROR:SPACING: space prohibited before that close parenthesis ')' #50: FILE: drivers/gpu/drm/xe/xe_pat.c:184:
+ [26] = XE3P_XPC_PAT( 0, 2, 0, 0, 0 ),
-:51: ERROR:SPACING: space prohibited after that open parenthesis '(' #51: FILE: drivers/gpu/drm/xe/xe_pat.c:185:
+ [27] = XE3P_XPC_PAT( 0, 2, 0, 0, 2 ),
-:51: ERROR:SPACING: space prohibited before that close parenthesis ')' #51: FILE: drivers/gpu/drm/xe/xe_pat.c:185:
+ [27] = XE3P_XPC_PAT( 0, 2, 0, 0, 2 ),
-:52: ERROR:SPACING: space prohibited after that open parenthesis '(' #52: FILE: drivers/gpu/drm/xe/xe_pat.c:186:
+ [28] = XE3P_XPC_PAT( 0, 2, 0, 0, 3 ),
-:52: ERROR:SPACING: space prohibited before that close parenthesis ')' #52: FILE: drivers/gpu/drm/xe/xe_pat.c:186:
+ [28] = XE3P_XPC_PAT( 0, 2, 0, 0, 3 ),
-:53: ERROR:SPACING: space prohibited after that open parenthesis '(' #53: FILE: drivers/gpu/drm/xe/xe_pat.c:187:
+ [29] = XE3P_XPC_PAT( 0, 3, 0, 0, 0 ),
-:53: ERROR:SPACING: space prohibited before that close parenthesis ')' #53: FILE: drivers/gpu/drm/xe/xe_pat.c:187:
+ [29] = XE3P_XPC_PAT( 0, 3, 0, 0, 0 ),
-:54: ERROR:SPACING: space prohibited after that open parenthesis '(' #54: FILE: drivers/gpu/drm/xe/xe_pat.c:188:
+ [30] = XE3P_XPC_PAT( 0, 3, 0, 0, 2 ),
-:54: ERROR:SPACING: space prohibited before that close parenthesis ')' #54: FILE: drivers/gpu/drm/xe/xe_pat.c:188:
+ [30] = XE3P_XPC_PAT( 0, 3, 0, 0, 2 ),
-:55: ERROR:SPACING: space prohibited after that open parenthesis '(' #55: FILE: drivers/gpu/drm/xe/xe_pat.c:189:
+ [31] = XE3P_XPC_PAT( 0, 3, 0, 0, 3 ),
-:55: ERROR:SPACING: space prohibited before that close parenthesis ')' #55: FILE: drivers/gpu/drm/xe/xe_pat.c:189:
+ [31] = XE3P_XPC_PAT( 0, 3, 0, 0, 3 ),
total: 54 errors, 0 warnings, 0 checks, 110 lines checked fd8bc35abbfa drm/xe/xe3p: Add xe3p EU stall data format
Patchwork
CI✓ CI.KUnit: success for drm/xe: Add Xe3p support
In reply to Lucas De Marchi== Series Details ==
== Series Details ==
Series: drm/xe: Add Xe3p support
URL : https://patchwork.freedesktop.org/series/155866/
State : success
== Summary ==
+ trap cleanup EXIT
+ /kernel/tools/testing/kunit/kunit.py run --kunitconfig /kernel/drivers/gpu/drm/xe/.kunitconfig [03:45:53] Configuring KUnit Kernel ...
Generating .config ...
Populating config with:
$ make ARCH=um O=.kunit olddefconfig [03:45:57] Building KUnit Kernel ... Populating config with: $ make ARCH=um O=.kunit olddefconfig Building with: $ make all compile_commands.json scripts_gdb ARCH=um O=.kunit --jobs=48 [03:46:28] Starting KUnit Kernel (1/1)... [03:46:28] ============================================================ Running tests with: $ .kunit/linux kunit.enable=1 mem=1G console=tty kunit_shutdown=halt [03:46:28] ================== guc_buf (11 subtests) =================== [03:46:28] [PASSED] test_smallest [03:46:28] [PASSED] test_largest [03:46:28] [PASSED] test_granular [03:46:28] [PASSED] test_unique [03:46:28] [PASSED] test_overlap [03:46:28] [PASSED] test_reusable [03:46:28] [PASSED] test_too_big [03:46:28] [PASSED] test_flush [03:46:28] [PASSED] test_lookup [03:46:28] [PASSED] test_data [03:46:28] [PASSED] test_class [03:46:28] ===================== [PASSED] guc_buf ===================== [03:46:28] =================== guc_dbm (7 subtests) =================== [03:46:28] [PASSED] test_empty [03:46:28] [PASSED] test_default [03:46:28] ======================== test_size ======================== [03:46:28] [PASSED] 4 [03:46:28] [PASSED] 8 [03:46:28] [PASSED] 32 [03:46:28] [PASSED] 256 [03:46:28] ==================== [PASSED] test_size ==================== [03:46:28] ======================= test_reuse ======================== [03:46:28] [PASSED] 4 [03:46:28] [PASSED] 8 [03:46:28] [PASSED] 32 [03:46:28] [PASSED] 256 [03:46:28] =================== [PASSED] test_reuse ==================== [03:46:28] =================== test_range_overlap ==================== [03:46:28] [PASSED] 4 [03:46:28] [PASSED] 8 [03:46:28] [PASSED] 32 [03:46:28] [PASSED] 256 [03:46:28] =============== [PASSED] test_range_overlap ================ [03:46:28] =================== test_range_compact ==================== [03:46:28] [PASSED] 4 [03:46:28] [PASSED] 8 [03:46:28] [PASSED] 32 [03:46:28] [PASSED] 256 [03:46:28] =============== [PASSED] test_range_compact ================ [03:46:28] ==================== test_range_spare ===================== [03:46:28] [PASSED] 4 [03:46:28] [PASSED] 8 [03:46:28] [PASSED] 32 [03:46:28] [PASSED] 256 [03:46:28] ================ [PASSED] test_range_spare ================= [03:46:28] ===================== [PASSED] guc_dbm ===================== [03:46:28] =================== guc_idm (6 subtests) =================== [03:46:28] [PASSED] bad_init [03:46:28] [PASSED] no_init [03:46:28] [PASSED] init_fini [03:46:28] [PASSED] check_used [03:46:28] [PASSED] check_quota [03:46:28] [PASSED] check_all [03:46:28] ===================== [PASSED] guc_idm ===================== [03:46:28] ================== no_relay (3 subtests) =================== [03:46:28] [PASSED] xe_drops_guc2pf_if_not_ready [03:46:28] [PASSED] xe_drops_guc2vf_if_not_ready [03:46:28] [PASSED] xe_rejects_send_if_not_ready [03:46:28] ==================== [PASSED] no_relay ===================== [03:46:28] ================== pf_relay (14 subtests) ================== [03:46:28] [PASSED] pf_rejects_guc2pf_too_short [03:46:28] [PASSED] pf_rejects_guc2pf_too_long [03:46:28] [PASSED] pf_rejects_guc2pf_no_payload [03:46:28] [PASSED] pf_fails_no_payload [03:46:28] [PASSED] pf_fails_bad_origin [03:46:28] [PASSED] pf_fails_bad_type [03:46:28] [PASSED] pf_txn_reports_error [03:46:28] [PASSED] pf_txn_sends_pf2guc [03:46:28] [PASSED] pf_sends_pf2guc [03:46:28] [SKIPPED] pf_loopback_nop [03:46:28] [SKIPPED] pf_loopback_echo [03:46:28] [SKIPPED] pf_loopback_fail [03:46:28] [SKIPPED] pf_loopback_busy [03:46:28] [SKIPPED] pf_loopback_retry [03:46:28] ==================== [PASSED] pf_relay ===================== [03:46:28] ================== vf_relay (3 subtests) =================== [03:46:28] [PASSED] vf_rejects_guc2vf_too_short [03:46:28] [PASSED] vf_rejects_guc2vf_too_long [03:46:28] [PASSED] vf_rejects_guc2vf_no_payload [03:46:28] ==================== [PASSED] vf_relay ===================== [03:46:28] ===================== lmtt (1 subtest) ===================== [03:46:28] ======================== test_ops ========================= [03:46:28] [PASSED] 2-level [03:46:28] [PASSED] multi-level [03:46:28] ==================== [PASSED] test_ops ===================== [03:46:28] ====================== [PASSED] lmtt ======================= [03:46:28] ================= pf_service (11 subtests) ================= [03:46:28] [PASSED] pf_negotiate_any [03:46:28] [PASSED] pf_negotiate_base_match [03:46:28] [PASSED] pf_negotiate_base_newer [03:46:28] [PASSED] pf_negotiate_base_next [03:46:28] [SKIPPED] pf_negotiate_base_older [03:46:28] [PASSED] pf_negotiate_base_prev [03:46:28] [PASSED] pf_negotiate_latest_match [03:46:28] [PASSED] pf_negotiate_latest_newer [03:46:28] [PASSED] pf_negotiate_latest_next [03:46:28] [SKIPPED] pf_negotiate_latest_older [03:46:28] [SKIPPED] pf_negotiate_latest_prev [03:46:28] =================== [PASSED] pf_service ==================== [03:46:28] ================= xe_guc_g2g (2 subtests) ================== [03:46:28] ============== xe_live_guc_g2g_kunit_default ============== [03:46:28] ========= [SKIPPED] xe_live_guc_g2g_kunit_default ========== [03:46:28] ============== xe_live_guc_g2g_kunit_allmem =============== [03:46:28] ========== [SKIPPED] xe_live_guc_g2g_kunit_allmem ========== [03:46:28] =================== [SKIPPED] xe_guc_g2g =================== [03:46:28] =================== xe_mocs (2 subtests) =================== [03:46:28] ================ xe_live_mocs_kernel_kunit ================ [03:46:28] =========== [SKIPPED] xe_live_mocs_kernel_kunit ============ [03:46:28] ================ xe_live_mocs_reset_kunit ================= [03:46:28] ============ [SKIPPED] xe_live_mocs_reset_kunit ============ [03:46:28] ==================== [SKIPPED] xe_mocs ===================== [03:46:28] ================= xe_migrate (2 subtests) ================== [03:46:28] ================= xe_migrate_sanity_kunit ================= [03:46:28] ============ [SKIPPED] xe_migrate_sanity_kunit ============= [03:46:28] ================== xe_validate_ccs_kunit ================== [03:46:28] ============= [SKIPPED] xe_validate_ccs_kunit ============== [03:46:28] =================== [SKIPPED] xe_migrate =================== [03:46:28] ================== xe_dma_buf (1 subtest) ================== [03:46:28] ==================== xe_dma_buf_kunit ===================== [03:46:28] ================ [SKIPPED] xe_dma_buf_kunit ================ [03:46:28] =================== [SKIPPED] xe_dma_buf =================== [03:46:28] ================= xe_bo_shrink (1 subtest) ================= [03:46:28] =================== xe_bo_shrink_kunit ==================== [03:46:28] =============== [SKIPPED] xe_bo_shrink_kunit =============== [03:46:28] ================== [SKIPPED] xe_bo_shrink ================== [03:46:28] ==================== xe_bo (2 subtests) ==================== [03:46:28] ================== xe_ccs_migrate_kunit =================== [03:46:28] ============== [SKIPPED] xe_ccs_migrate_kunit ============== [03:46:28] ==================== xe_bo_evict_kunit ==================== [03:46:28] =============== [SKIPPED] xe_bo_evict_kunit ================ [03:46:28] ===================== [SKIPPED] xe_bo ====================== [03:46:28] ==================== args (11 subtests) ==================== [03:46:28] [PASSED] count_args_test [03:46:28] [PASSED] call_args_example [03:46:28] [PASSED] call_args_test [03:46:28] [PASSED] drop_first_arg_example [03:46:28] [PASSED] drop_first_arg_test [03:46:28] [PASSED] first_arg_example [03:46:28] [PASSED] first_arg_test [03:46:28] [PASSED] last_arg_example [03:46:28] [PASSED] last_arg_test [03:46:28] [PASSED] pick_arg_example [03:46:28] [PASSED] sep_comma_example [03:46:28] ====================== [PASSED] args ======================= [03:46:28] =================== xe_pci (3 subtests) ==================== [03:46:28] ==================== check_graphics_ip ==================== [03:46:28] [PASSED] 12.00 Xe_LP [03:46:28] [PASSED] 12.10 Xe_LP+ [03:46:28] [PASSED] 12.55 Xe_HPG [03:46:28] [PASSED] 12.60 Xe_HPC [03:46:28] [PASSED] 12.70 Xe_LPG [03:46:28] [PASSED] 12.71 Xe_LPG [03:46:28] [PASSED] 12.74 Xe_LPG+ [03:46:28] [PASSED] 20.01 Xe2_HPG [03:46:28] [PASSED] 20.02 Xe2_HPG [03:46:28] [PASSED] 20.04 Xe2_LPG [03:46:28] [PASSED] 30.00 Xe3_LPG [03:46:28] [PASSED] 30.01 Xe3_LPG [03:46:28] [PASSED] 30.03 Xe3_LPG [03:46:28] [PASSED] 30.04 Xe3_LPG [03:46:28] [PASSED] 30.05 Xe3_LPG [03:46:28] [PASSED] 35.11 Xe3p_XPC [03:46:28] ================ [PASSED] check_graphics_ip ================ [03:46:28] ===================== check_media_ip ====================== [03:46:28] [PASSED] 12.00 Xe_M [03:46:28] [PASSED] 12.55 Xe_HPM [03:46:28] [PASSED] 13.00 Xe_LPM+ [03:46:28] [PASSED] 13.01 Xe2_HPM [03:46:28] [PASSED] 20.00 Xe2_LPM [03:46:28] [PASSED] 30.00 Xe3_LPM [03:46:28] [PASSED] 30.02 Xe3_LPM [03:46:28] [PASSED] 35.00 Xe3p_LPM [03:46:28] [PASSED] 35.03 Xe3p_LPM [03:46:28] ================= [PASSED] check_media_ip ================== [03:46:28] ================= check_platform_gt_count ================= [03:46:28] [PASSED] 0x9A60 (TIGERLAKE) [03:46:28] [PASSED] 0x9A68 (TIGERLAKE) [03:46:28] [PASSED] 0x9A70 (TIGERLAKE) [03:46:28] [PASSED] 0x9A40 (TIGERLAKE) [03:46:28] [PASSED] 0x9A49 (TIGERLAKE) [03:46:28] [PASSED] 0x9A59 (TIGERLAKE) [03:46:28] [PASSED] 0x9A78 (TIGERLAKE) [03:46:28] [PASSED] 0x9AC0 (TIGERLAKE) [03:46:28] [PASSED] 0x9AC9 (TIGERLAKE) [03:46:28] [PASSED] 0x9AD9 (TIGERLAKE) [03:46:28] [PASSED] 0x9AF8 (TIGERLAKE) [03:46:28] [PASSED] 0x4C80 (ROCKETLAKE) [03:46:28] [PASSED] 0x4C8A (ROCKETLAKE) [03:46:28] [PASSED] 0x4C8B (ROCKETLAKE) [03:46:28] [PASSED] 0x4C8C (ROCKETLAKE) [03:46:28] [PASSED] 0x4C90 (ROCKETLAKE) [03:46:28] [PASSED] 0x4C9A (ROCKETLAKE) [03:46:28] [PASSED] 0x4680 (ALDERLAKE_S) [03:46:28] [PASSED] 0x4682 (ALDERLAKE_S) [03:46:28] [PASSED] 0x4688 (ALDERLAKE_S) [03:46:28] [PASSED] 0x468A (ALDERLAKE_S) [03:46:28] [PASSED] 0x468B (ALDERLAKE_S) [03:46:28] [PASSED] 0x4690 (ALDERLAKE_S) [03:46:28] [PASSED] 0x4692 (ALDERLAKE_S) [03:46:28] [PASSED] 0x4693 (ALDERLAKE_S) [03:46:28] [PASSED] 0x46A0 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46A1 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46A2 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46A3 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46A6 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46A8 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46AA (ALDERLAKE_P) [03:46:28] [PASSED] 0x462A (ALDERLAKE_P) [03:46:28] [PASSED] 0x4626 (ALDERLAKE_P) [03:46:28] [PASSED] 0x4628 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46B0 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46B1 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46B2 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46B3 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46C0 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46C1 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46C2 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46C3 (ALDERLAKE_P) [03:46:28] [PASSED] 0x46D0 (ALDERLAKE_N) [03:46:28] [PASSED] 0x46D1 (ALDERLAKE_N) [03:46:28] [PASSED] 0x46D2 (ALDERLAKE_N) [03:46:28] [PASSED] 0x46D3 (ALDERLAKE_N) [03:46:28] [PASSED] 0x46D4 (ALDERLAKE_N) [03:46:28] [PASSED] 0xA721 (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7A1 (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7A9 (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7AC (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7AD (ALDERLAKE_P) [03:46:28] [PASSED] 0xA720 (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7A0 (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7A8 (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7AA (ALDERLAKE_P) [03:46:28] [PASSED] 0xA7AB (ALDERLAKE_P) [03:46:28] [PASSED] 0xA780 (ALDERLAKE_S) [03:46:28] [PASSED] 0xA781 (ALDERLAKE_S) [03:46:28] [PASSED] 0xA782 (ALDERLAKE_S) [03:46:28] [PASSED] 0xA783 (ALDERLAKE_S) [03:46:28] [PASSED] 0xA788 (ALDERLAKE_S) [03:46:28] [PASSED] 0xA789 (ALDERLAKE_S) [03:46:28] [PASSED] 0xA78A (ALDERLAKE_S) [03:46:28] [PASSED] 0xA78B (ALDERLAKE_S) [03:46:28] [PASSED] 0x4905 (DG1) [03:46:28] [PASSED] 0x4906 (DG1) [03:46:28] [PASSED] 0x4907 (DG1) [03:46:28] [PASSED] 0x4908 (DG1) [03:46:28] [PASSED] 0x4909 (DG1) [03:46:28] [PASSED] 0x56C0 (DG2) [03:46:28] [PASSED] 0x56C2 (DG2) [03:46:28] [PASSED] 0x56C1 (DG2) [03:46:28] [PASSED] 0x7D51 (METEORLAKE) [03:46:28] [PASSED] 0x7DD1 (METEORLAKE) [03:46:28] [PASSED] 0x7D41 (METEORLAKE) [03:46:28] [PASSED] 0x7D67 (METEORLAKE) [03:46:28] [PASSED] 0xB640 (METEORLAKE) [03:46:28] [PASSED] 0x56A0 (DG2) [03:46:28] [PASSED] 0x56A1 (DG2) [03:46:28] [PASSED] 0x56A2 (DG2) [03:46:28] [PASSED] 0x56BE (DG2) [03:46:28] [PASSED] 0x56BF (DG2) [03:46:28] [PASSED] 0x5690 (DG2) [03:46:28] [PASSED] 0x5691 (DG2) [03:46:28] [PASSED] 0x5692 (DG2) [03:46:28] [PASSED] 0x56A5 (DG2) [03:46:28] [PASSED] 0x56A6 (DG2) [03:46:28] [PASSED] 0x56B0 (DG2) [03:46:28] [PASSED] 0x56B1 (DG2) [03:46:28] [PASSED] 0x56BA (DG2) [03:46:28] [PASSED] 0x56BB (DG2) [03:46:28] [PASSED] 0x56BC (DG2) [03:46:28] [PASSED] 0x56BD (DG2) [03:46:28] [PASSED] 0x5693 (DG2) [03:46:28] [PASSED] 0x5694 (DG2) [03:46:28] [PASSED] 0x5695 (DG2) [03:46:28] [PASSED] 0x56A3 (DG2) [03:46:28] [PASSED] 0x56A4 (DG2) [03:46:28] [PASSED] 0x56B2 (DG2) [03:46:28] [PASSED] 0x56B3 (DG2) [03:46:28] [PASSED] 0x5696 (DG2) [03:46:28] [PASSED] 0x5697 (DG2) [03:46:28] [PASSED] 0xB69 (PVC) [03:46:28] [PASSED] 0xB6E (PVC) [03:46:28] [PASSED] 0xBD4 (PVC) [03:46:28] [PASSED] 0xBD5 (PVC) [03:46:28] [PASSED] 0xBD6 (PVC) [03:46:28] [PASSED] 0xBD7 (PVC) [03:46:28] [PASSED] 0xBD8 (PVC) [03:46:28] [PASSED] 0xBD9 (PVC) [03:46:28] [PASSED] 0xBDA (PVC) [03:46:28] [PASSED] 0xBDB (PVC) [03:46:28] [PASSED] 0xBE0 (PVC) [03:46:28] [PASSED] 0xBE1 (PVC) [03:46:28] [PASSED] 0xBE5 (PVC) [03:46:28] [PASSED] 0x7D40 (METEORLAKE) [03:46:28] [PASSED] 0x7D45 (METEORLAKE) [03:46:28] [PASSED] 0x7D55 (METEORLAKE) [03:46:28] [PASSED] 0x7D60 (METEORLAKE) [03:46:28] [PASSED] 0x7DD5 (METEORLAKE) [03:46:28] [PASSED] 0x6420 (LUNARLAKE) [03:46:28] [PASSED] 0x64A0 (LUNARLAKE) [03:46:28] [PASSED] 0x64B0 (LUNARLAKE) [03:46:28] [PASSED] 0xE202 (BATTLEMAGE) [03:46:28] [PASSED] 0xE209 (BATTLEMAGE) [03:46:28] [PASSED] 0xE20B (BATTLEMAGE) [03:46:28] [PASSED] 0xE20C (BATTLEMAGE) [03:46:28] [PASSED] 0xE20D (BATTLEMAGE) [03:46:28] [PASSED] 0xE210 (BATTLEMAGE) [03:46:28] [PASSED] 0xE211 (BATTLEMAGE) [03:46:28] [PASSED] 0xE212 (BATTLEMAGE) [03:46:28] [PASSED] 0xE216 (BATTLEMAGE) [03:46:28] [PASSED] 0xE220 (BATTLEMAGE) [03:46:28] [PASSED] 0xE221 (BATTLEMAGE) [03:46:28] [PASSED] 0xE222 (BATTLEMAGE) [03:46:28] [PASSED] 0xE223 (BATTLEMAGE) [03:46:28] [PASSED] 0xB080 (PANTHERLAKE) [03:46:28] [PASSED] 0xB081 (PANTHERLAKE) [03:46:28] [PASSED] 0xB082 (PANTHERLAKE) [03:46:28] [PASSED] 0xB083 (PANTHERLAKE) [03:46:28] [PASSED] 0xB084 (PANTHERLAKE) [03:46:28] [PASSED] 0xB085 (PANTHERLAKE) [03:46:28] [PASSED] 0xB086 (PANTHERLAKE) [03:46:28] [PASSED] 0xB087 (PANTHERLAKE) [03:46:28] [PASSED] 0xB08F (PANTHERLAKE) [03:46:28] [PASSED] 0xB090 (PANTHERLAKE) [03:46:28] [PASSED] 0xB0A0 (PANTHERLAKE) [03:46:28] [PASSED] 0xB0B0 (PANTHERLAKE) [03:46:28] [PASSED] 0xFD80 (PANTHERLAKE) [03:46:28] [PASSED] 0xFD81 (PANTHERLAKE) [03:46:28] [PASSED] 0xD740 (NOVALAKE_S) [03:46:28] [PASSED] 0xD741 (NOVALAKE_S) [03:46:28] [PASSED] 0xD742 (NOVALAKE_S) [03:46:28] [PASSED] 0xD743 (NOVALAKE_S) [03:46:28] [PASSED] 0xD744 (NOVALAKE_S) [03:46:28] [PASSED] 0xD745 (NOVALAKE_S) [03:46:28] ============= [PASSED] check_platform_gt_count ============= [03:46:28] ===================== [PASSED] xe_pci ====================== [03:46:28] =================== xe_rtp (2 subtests) ==================== [03:46:28] =============== xe_rtp_process_to_sr_tests ================ [03:46:28] [PASSED] coalesce-same-reg [03:46:28] [PASSED] no-match-no-add [03:46:28] [PASSED] match-or [03:46:28] [PASSED] match-or-xfail [03:46:28] [PASSED] no-match-no-add-multiple-rules [03:46:28] [PASSED] two-regs-two-entries [03:46:28] [PASSED] clr-one-set-other [03:46:28] [PASSED] set-field [03:46:28] [PASSED] conflict-duplicate [03:46:28] [PASSED] conflict-not-disjoint [03:46:28] [PASSED] conflict-reg-type [03:46:28] =========== [PASSED] xe_rtp_process_to_sr_tests ============ [03:46:28] ================== xe_rtp_process_tests =================== [03:46:28] [PASSED] active1 [03:46:28] [PASSED] active2 [03:46:28] [PASSED] active-inactive [03:46:28] [PASSED] inactive-active [03:46:28] [PASSED] inactive-1st_or_active-inactive [03:46:28] [PASSED] inactive-2nd_or_active-inactive [03:46:28] [PASSED] inactive-last_or_active-inactive [03:46:28] [PASSED] inactive-no_or_active-inactive stty: 'standard input': Inappropriate ioctl for device [03:46:28] ============== [PASSED] xe_rtp_process_tests =============== [03:46:28] ===================== [PASSED] xe_rtp ====================== [03:46:28] ==================== xe_wa (1 subtest) ===================== [03:46:28] ======================== xe_wa_gt ========================= [03:46:28] [PASSED] TIGERLAKE B0 [03:46:28] [PASSED] DG1 A0 [03:46:28] [PASSED] DG1 B0 [03:46:28] [PASSED] ALDERLAKE_S A0 [03:46:28] [PASSED] ALDERLAKE_S B0 [03:46:28] [PASSED] ALDERLAKE_S C0 [03:46:28] [PASSED] ALDERLAKE_S D0 [03:46:28] [PASSED] ALDERLAKE_P A0 [03:46:28] [PASSED] ALDERLAKE_P B0 [03:46:28] [PASSED] ALDERLAKE_P C0 [03:46:28] [PASSED] ALDERLAKE_S RPLS D0 [03:46:28] [PASSED] ALDERLAKE_P RPLU E0 [03:46:28] [PASSED] DG2 G10 C0 [03:46:28] [PASSED] DG2 G11 B1 [03:46:28] [PASSED] DG2 G12 A1 [03:46:28] [PASSED] METEORLAKE 12.70(Xe_LPG) A0 13.00(Xe_LPM+) A0 [03:46:28] [PASSED] METEORLAKE 12.71(Xe_LPG) A0 13.00(Xe_LPM+) A0 [03:46:28] [PASSED] METEORLAKE 12.74(Xe_LPG+) A0 13.00(Xe_LPM+) A0 [03:46:28] [PASSED] LUNARLAKE 20.04(Xe2_LPG) A0 20.00(Xe2_LPM) A0 [03:46:28] [PASSED] LUNARLAKE 20.04(Xe2_LPG) B0 20.00(Xe2_LPM) A0 [03:46:28] [PASSED] BATTLEMAGE 20.01(Xe2_HPG) A0 13.01(Xe2_HPM) A1 [03:46:28] [PASSED] PANTHERLAKE 30.00(Xe3_LPG) A0 30.00(Xe3_LPM) A0 [03:46:28] ==================== [PASSED] xe_wa_gt ===================== [03:46:28] ====================== [PASSED] xe_wa ====================== [03:46:28] ============================================================ [03:46:28] Testing complete. Ran 317 tests: passed: 299, skipped: 18 [03:46:28] Elapsed time: 35.114s total, 4.215s configuring, 30.532s building, 0.333s running
+ /kernel/tools/testing/kunit/kunit.py run --kunitconfig /kernel/drivers/gpu/drm/tests/.kunitconfig [03:46:28] Configuring KUnit Kernel ...
Regenerating .config ...
Populating config with:
$ make ARCH=um O=.kunit olddefconfig [03:46:30] Building KUnit Kernel ... Populating config with: $ make ARCH=um O=.kunit olddefconfig Building with: $ make all compile_commands.json scripts_gdb ARCH=um O=.kunit --jobs=48 [03:46:54] Starting KUnit Kernel (1/1)... [03:46:54] ============================================================ Running tests with: $ .kunit/linux kunit.enable=1 mem=1G console=tty kunit_shutdown=halt [03:46:55] ============ drm_test_pick_cmdline (2 subtests) ============ [03:46:55] [PASSED] drm_test_pick_cmdline_res_1920_1080_60 [03:46:55] =============== drm_test_pick_cmdline_named =============== [03:46:55] [PASSED] NTSC [03:46:55] [PASSED] NTSC-J [03:46:55] [PASSED] PAL [03:46:55] [PASSED] PAL-M [03:46:55] =========== [PASSED] drm_test_pick_cmdline_named =========== [03:46:55] ============== [PASSED] drm_test_pick_cmdline ============== [03:46:55] == drm_test_atomic_get_connector_for_encoder (1 subtest) === [03:46:55] [PASSED] drm_test_drm_atomic_get_connector_for_encoder [03:46:55] ==== [PASSED] drm_test_atomic_get_connector_for_encoder ==== [03:46:55] =========== drm_validate_clone_mode (2 subtests) =========== [03:46:55] ============== drm_test_check_in_clone_mode =============== [03:46:55] [PASSED] in_clone_mode [03:46:55] [PASSED] not_in_clone_mode [03:46:55] ========== [PASSED] drm_test_check_in_clone_mode =========== [03:46:55] =============== drm_test_check_valid_clones =============== [03:46:55] [PASSED] not_in_clone_mode [03:46:55] [PASSED] valid_clone [03:46:55] [PASSED] invalid_clone [03:46:55] =========== [PASSED] drm_test_check_valid_clones =========== [03:46:55] ============= [PASSED] drm_validate_clone_mode ============= [03:46:55] ============= drm_validate_modeset (1 subtest) ============= [03:46:55] [PASSED] drm_test_check_connector_changed_modeset [03:46:55] ============== [PASSED] drm_validate_modeset =============== [03:46:55] ====== drm_test_bridge_get_current_state (2 subtests) ====== [03:46:55] [PASSED] drm_test_drm_bridge_get_current_state_atomic [03:46:55] [PASSED] drm_test_drm_bridge_get_current_state_legacy [03:46:55] ======== [PASSED] drm_test_bridge_get_current_state ======== [03:46:55] ====== drm_test_bridge_helper_reset_crtc (3 subtests) ====== [03:46:55] [PASSED] drm_test_drm_bridge_helper_reset_crtc_atomic [03:46:55] [PASSED] drm_test_drm_bridge_helper_reset_crtc_atomic_disabled [03:46:55] [PASSED] drm_test_drm_bridge_helper_reset_crtc_legacy [03:46:55] ======== [PASSED] drm_test_bridge_helper_reset_crtc ======== [03:46:55] ============== drm_bridge_alloc (2 subtests) =============== [03:46:55] [PASSED] drm_test_drm_bridge_alloc_basic [03:46:55] [PASSED] drm_test_drm_bridge_alloc_get_put [03:46:55] ================ [PASSED] drm_bridge_alloc ================= [03:46:55] ================== drm_buddy (8 subtests) ================== [03:46:55] [PASSED] drm_test_buddy_alloc_limit [03:46:55] [PASSED] drm_test_buddy_alloc_optimistic [03:46:55] [PASSED] drm_test_buddy_alloc_pessimistic [03:46:55] [PASSED] drm_test_buddy_alloc_pathological [03:46:55] [PASSED] drm_test_buddy_alloc_contiguous [03:46:55] [PASSED] drm_test_buddy_alloc_clear [03:46:55] [PASSED] drm_test_buddy_alloc_range_bias [03:46:55] [PASSED] drm_test_buddy_fragmentation_performance [03:46:55] ==================== [PASSED] drm_buddy ==================== [03:46:55] ============= drm_cmdline_parser (40 subtests) ============= [03:46:55] [PASSED] drm_test_cmdline_force_d_only [03:46:55] [PASSED] drm_test_cmdline_force_D_only_dvi [03:46:55] [PASSED] drm_test_cmdline_force_D_only_hdmi [03:46:55] [PASSED] drm_test_cmdline_force_D_only_not_digital [03:46:55] [PASSED] drm_test_cmdline_force_e_only [03:46:55] [PASSED] drm_test_cmdline_res [03:46:55] [PASSED] drm_test_cmdline_res_vesa [03:46:55] [PASSED] drm_test_cmdline_res_vesa_rblank [03:46:55] [PASSED] drm_test_cmdline_res_rblank [03:46:55] [PASSED] drm_test_cmdline_res_bpp [03:46:55] [PASSED] drm_test_cmdline_res_refresh [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_interlaced [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_margins [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_force_off [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_force_on [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_force_on_analog [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_force_on_digital [03:46:55] [PASSED] drm_test_cmdline_res_bpp_refresh_interlaced_margins_force_on [03:46:55] [PASSED] drm_test_cmdline_res_margins_force_on [03:46:55] [PASSED] drm_test_cmdline_res_vesa_margins [03:46:55] [PASSED] drm_test_cmdline_name [03:46:55] [PASSED] drm_test_cmdline_name_bpp [03:46:55] [PASSED] drm_test_cmdline_name_option [03:46:55] [PASSED] drm_test_cmdline_name_bpp_option [03:46:55] [PASSED] drm_test_cmdline_rotate_0 [03:46:55] [PASSED] drm_test_cmdline_rotate_90 [03:46:55] [PASSED] drm_test_cmdline_rotate_180 [03:46:55] [PASSED] drm_test_cmdline_rotate_270 [03:46:55] [PASSED] drm_test_cmdline_hmirror [03:46:55] [PASSED] drm_test_cmdline_vmirror [03:46:55] [PASSED] drm_test_cmdline_margin_options [03:46:55] [PASSED] drm_test_cmdline_multiple_options [03:46:55] [PASSED] drm_test_cmdline_bpp_extra_and_option [03:46:55] [PASSED] drm_test_cmdline_extra_and_option [03:46:55] [PASSED] drm_test_cmdline_freestanding_options [03:46:55] [PASSED] drm_test_cmdline_freestanding_force_e_and_options [03:46:55] [PASSED] drm_test_cmdline_panel_orientation [03:46:55] ================ drm_test_cmdline_invalid ================= [03:46:55] [PASSED] margin_only [03:46:55] [PASSED] interlace_only [03:46:55] [PASSED] res_missing_x [03:46:55] [PASSED] res_missing_y [03:46:55] [PASSED] res_bad_y [03:46:55] [PASSED] res_missing_y_bpp [03:46:55] [PASSED] res_bad_bpp [03:46:55] [PASSED] res_bad_refresh [03:46:55] [PASSED] res_bpp_refresh_force_on_off [03:46:55] [PASSED] res_invalid_mode [03:46:55] [PASSED] res_bpp_wrong_place_mode [03:46:55] [PASSED] name_bpp_refresh [03:46:55] [PASSED] name_refresh [03:46:55] [PASSED] name_refresh_wrong_mode [03:46:55] [PASSED] name_refresh_invalid_mode [03:46:55] [PASSED] rotate_multiple [03:46:55] [PASSED] rotate_invalid_val [03:46:55] [PASSED] rotate_truncated [03:46:55] [PASSED] invalid_option [03:46:55] [PASSED] invalid_tv_option [03:46:55] [PASSED] truncated_tv_option [03:46:55] ============ [PASSED] drm_test_cmdline_invalid ============= [03:46:55] =============== drm_test_cmdline_tv_options =============== [03:46:55] [PASSED] NTSC [03:46:55] [PASSED] NTSC_443 [03:46:55] [PASSED] NTSC_J [03:46:55] [PASSED] PAL [03:46:55] [PASSED] PAL_M [03:46:55] [PASSED] PAL_N [03:46:55] [PASSED] SECAM [03:46:55] [PASSED] MONO_525 [03:46:55] [PASSED] MONO_625 [03:46:55] =========== [PASSED] drm_test_cmdline_tv_options =========== [03:46:55] =============== [PASSED] drm_cmdline_parser ================ [03:46:55] ========== drmm_connector_hdmi_init (20 subtests) ========== [03:46:55] [PASSED] drm_test_connector_hdmi_init_valid [03:46:55] [PASSED] drm_test_connector_hdmi_init_bpc_8 [03:46:55] [PASSED] drm_test_connector_hdmi_init_bpc_10 [03:46:55] [PASSED] drm_test_connector_hdmi_init_bpc_12 [03:46:55] [PASSED] drm_test_connector_hdmi_init_bpc_invalid [03:46:55] [PASSED] drm_test_connector_hdmi_init_bpc_null [03:46:55] [PASSED] drm_test_connector_hdmi_init_formats_empty [03:46:55] [PASSED] drm_test_connector_hdmi_init_formats_no_rgb [03:46:55] === drm_test_connector_hdmi_init_formats_yuv420_allowed === [03:46:55] [PASSED] supported_formats=0x9 yuv420_allowed=1 [03:46:55] [PASSED] supported_formats=0x9 yuv420_allowed=0 [03:46:55] [PASSED] supported_formats=0x3 yuv420_allowed=1 [03:46:55] [PASSED] supported_formats=0x3 yuv420_allowed=0 [03:46:55] === [PASSED] drm_test_connector_hdmi_init_formats_yuv420_allowed === [03:46:55] [PASSED] drm_test_connector_hdmi_init_null_ddc [03:46:55] [PASSED] drm_test_connector_hdmi_init_null_product [03:46:55] [PASSED] drm_test_connector_hdmi_init_null_vendor [03:46:55] [PASSED] drm_test_connector_hdmi_init_product_length_exact [03:46:55] [PASSED] drm_test_connector_hdmi_init_product_length_too_long [03:46:55] [PASSED] drm_test_connector_hdmi_init_product_valid [03:46:55] [PASSED] drm_test_connector_hdmi_init_vendor_length_exact [03:46:55] [PASSED] drm_test_connector_hdmi_init_vendor_length_too_long [03:46:55] [PASSED] drm_test_connector_hdmi_init_vendor_valid [03:46:55] ========= drm_test_connector_hdmi_init_type_valid ========= [03:46:55] [PASSED] HDMI-A [03:46:55] [PASSED] HDMI-B [03:46:55] ===== [PASSED] drm_test_connector_hdmi_init_type_valid ===== [03:46:55] ======== drm_test_connector_hdmi_init_type_invalid ======== [03:46:55] [PASSED] Unknown [03:46:55] [PASSED] VGA [03:46:55] [PASSED] DVI-I [03:46:55] [PASSED] DVI-D [03:46:55] [PASSED] DVI-A [03:46:55] [PASSED] Composite [03:46:55] [PASSED] SVIDEO [03:46:55] [PASSED] LVDS [03:46:55] [PASSED] Component [03:46:55] [PASSED] DIN [03:46:55] [PASSED] DP [03:46:55] [PASSED] TV [03:46:55] [PASSED] eDP [03:46:55] [PASSED] Virtual [03:46:55] [PASSED] DSI [03:46:55] [PASSED] DPI [03:46:55] [PASSED] Writeback [03:46:55] [PASSED] SPI [03:46:55] [PASSED] USB [03:46:55] ==== [PASSED] drm_test_connector_hdmi_init_type_invalid ==== [03:46:55] ============ [PASSED] drmm_connector_hdmi_init ============= [03:46:55] ============= drmm_connector_init (3 subtests) ============= [03:46:55] [PASSED] drm_test_drmm_connector_init [03:46:55] [PASSED] drm_test_drmm_connector_init_null_ddc [03:46:55] ========= drm_test_drmm_connector_init_type_valid ========= [03:46:55] [PASSED] Unknown [03:46:55] [PASSED] VGA [03:46:55] [PASSED] DVI-I [03:46:55] [PASSED] DVI-D [03:46:55] [PASSED] DVI-A [03:46:55] [PASSED] Composite [03:46:55] [PASSED] SVIDEO [03:46:55] [PASSED] LVDS [03:46:55] [PASSED] Component [03:46:55] [PASSED] DIN [03:46:55] [PASSED] DP [03:46:55] [PASSED] HDMI-A [03:46:55] [PASSED] HDMI-B [03:46:55] [PASSED] TV [03:46:55] [PASSED] eDP [03:46:55] [PASSED] Virtual [03:46:55] [PASSED] DSI [03:46:55] [PASSED] DPI [03:46:55] [PASSED] Writeback [03:46:55] [PASSED] SPI [03:46:55] [PASSED] USB [03:46:55] ===== [PASSED] drm_test_drmm_connector_init_type_valid ===== [03:46:55] =============== [PASSED] drmm_connector_init =============== [03:46:55] ========= drm_connector_dynamic_init (6 subtests) ========== [03:46:55] [PASSED] drm_test_drm_connector_dynamic_init [03:46:55] [PASSED] drm_test_drm_connector_dynamic_init_null_ddc [03:46:55] [PASSED] drm_test_drm_connector_dynamic_init_not_added [03:46:55] [PASSED] drm_test_drm_connector_dynamic_init_properties [03:46:55] ===== drm_test_drm_connector_dynamic_init_type_valid ====== [03:46:55] [PASSED] Unknown [03:46:55] [PASSED] VGA [03:46:55] [PASSED] DVI-I [03:46:55] [PASSED] DVI-D [03:46:55] [PASSED] DVI-A [03:46:55] [PASSED] Composite [03:46:55] [PASSED] SVIDEO [03:46:55] [PASSED] LVDS [03:46:55] [PASSED] Component [03:46:55] [PASSED] DIN [03:46:55] [PASSED] DP [03:46:55] [PASSED] HDMI-A [03:46:55] [PASSED] HDMI-B [03:46:55] [PASSED] TV [03:46:55] [PASSED] eDP [03:46:55] [PASSED] Virtual [03:46:55] [PASSED] DSI [03:46:55] [PASSED] DPI [03:46:55] [PASSED] Writeback [03:46:55] [PASSED] SPI [03:46:55] [PASSED] USB [03:46:55] = [PASSED] drm_test_drm_connector_dynamic_init_type_valid == [03:46:55] ======== drm_test_drm_connector_dynamic_init_name ========= [03:46:55] [PASSED] Unknown [03:46:55] [PASSED] VGA [03:46:55] [PASSED] DVI-I [03:46:55] [PASSED] DVI-D [03:46:55] [PASSED] DVI-A [03:46:55] [PASSED] Composite [03:46:55] [PASSED] SVIDEO [03:46:55] [PASSED] LVDS [03:46:55] [PASSED] Component [03:46:55] [PASSED] DIN [03:46:55] [PASSED] DP [03:46:55] [PASSED] HDMI-A [03:46:55] [PASSED] HDMI-B [03:46:55] [PASSED] TV [03:46:55] [PASSED] eDP [03:46:55] [PASSED] Virtual [03:46:55] [PASSED] DSI [03:46:55] [PASSED] DPI [03:46:55] [PASSED] Writeback [03:46:55] [PASSED] SPI [03:46:55] [PASSED] USB [03:46:55] ==== [PASSED] drm_test_drm_connector_dynamic_init_name ===== [03:46:55] =========== [PASSED] drm_connector_dynamic_init ============ [03:46:55] ==== drm_connector_dynamic_register_early (4 subtests) ===== [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_early_on_list [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_early_defer [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_early_no_init [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_early_no_mode_object [03:46:55] ====== [PASSED] drm_connector_dynamic_register_early ======= [03:46:55] ======= drm_connector_dynamic_register (7 subtests) ======== [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_on_list [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_no_defer [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_no_init [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_mode_object [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_sysfs [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_sysfs_name [03:46:55] [PASSED] drm_test_drm_connector_dynamic_register_debugfs [03:46:55] ========= [PASSED] drm_connector_dynamic_register ========== [03:46:55] = drm_connector_attach_broadcast_rgb_property (2 subtests) = [03:46:55] [PASSED] drm_test_drm_connector_attach_broadcast_rgb_property [03:46:55] [PASSED] drm_test_drm_connector_attach_broadcast_rgb_property_hdmi_connector [03:46:55] === [PASSED] drm_connector_attach_broadcast_rgb_property === [03:46:55] ========== drm_get_tv_mode_from_name (2 subtests) ========== [03:46:55] ========== drm_test_get_tv_mode_from_name_valid =========== [03:46:55] [PASSED] NTSC [03:46:55] [PASSED] NTSC-443 [03:46:55] [PASSED] NTSC-J [03:46:55] [PASSED] PAL [03:46:55] [PASSED] PAL-M [03:46:55] [PASSED] PAL-N [03:46:55] [PASSED] SECAM [03:46:55] [PASSED] Mono [03:46:55] ====== [PASSED] drm_test_get_tv_mode_from_name_valid ======= [03:46:55] [PASSED] drm_test_get_tv_mode_from_name_truncated [03:46:55] ============ [PASSED] drm_get_tv_mode_from_name ============ [03:46:55] = drm_test_connector_hdmi_compute_mode_clock (12 subtests) = [03:46:55] [PASSED] drm_test_drm_hdmi_compute_mode_clock_rgb [03:46:55] [PASSED] drm_test_drm_hdmi_compute_mode_clock_rgb_10bpc [03:46:55] [PASSED] drm_test_drm_hdmi_compute_mode_clock_rgb_10bpc_vic_1 [03:46:55] [PASSED] drm_test_drm_hdmi_compute_mode_clock_rgb_12bpc [03:46:55] [PASSED] drm_test_drm_hdmi_compute_mode_clock_rgb_12bpc_vic_1 [03:46:55] [PASSED] drm_test_drm_hdmi_compute_mode_clock_rgb_double [03:46:55] = drm_test_connector_hdmi_compute_mode_clock_yuv420_valid = [03:46:55] [PASSED] VIC 96 [03:46:55] [PASSED] VIC 97 [03:46:55] [PASSED] VIC 101 [03:46:55] [PASSED] VIC 102 [03:46:55] [PASSED] VIC 106 [03:46:55] [PASSED] VIC 107 [03:46:55] === [PASSED] drm_test_connector_hdmi_compute_mode_clock_yuv420_valid === [03:46:55] [PASSED] drm_test_connector_hdmi_compute_mode_clock_yuv420_10_bpc [03:46:55] [PASSED] drm_test_connector_hdmi_compute_mode_clock_yuv420_12_bpc [03:46:55] [PASSED] drm_test_connector_hdmi_compute_mode_clock_yuv422_8_bpc [03:46:55] [PASSED] drm_test_connector_hdmi_compute_mode_clock_yuv422_10_bpc [03:46:55] [PASSED] drm_test_connector_hdmi_compute_mode_clock_yuv422_12_bpc [03:46:55] === [PASSED] drm_test_connector_hdmi_compute_mode_clock ==== [03:46:55] == drm_hdmi_connector_get_broadcast_rgb_name (2 subtests) == [03:46:55] === drm_test_drm_hdmi_connector_get_broadcast_rgb_name ==== [03:46:55] [PASSED] Automatic [03:46:55] [PASSED] Full [03:46:55] [PASSED] Limited 16:235 [03:46:55] === [PASSED] drm_test_drm_hdmi_connector_get_broadcast_rgb_name === [03:46:55] [PASSED] drm_test_drm_hdmi_connector_get_broadcast_rgb_name_invalid [03:46:55] ==== [PASSED] drm_hdmi_connector_get_broadcast_rgb_name ==== [03:46:55] == drm_hdmi_connector_get_output_format_name (2 subtests) == [03:46:55] === drm_test_drm_hdmi_connector_get_output_format_name ==== [03:46:55] [PASSED] RGB [03:46:55] [PASSED] YUV 4:2:0 [03:46:55] [PASSED] YUV 4:2:2 [03:46:55] [PASSED] YUV 4:4:4 [03:46:55] === [PASSED] drm_test_drm_hdmi_connector_get_output_format_name === [03:46:55] [PASSED] drm_test_drm_hdmi_connector_get_output_format_name_invalid [03:46:55] ==== [PASSED] drm_hdmi_connector_get_output_format_name ==== [03:46:55] ============= drm_damage_helper (21 subtests) ============== [03:46:55] [PASSED] drm_test_damage_iter_no_damage [03:46:55] [PASSED] drm_test_damage_iter_no_damage_fractional_src [03:46:55] [PASSED] drm_test_damage_iter_no_damage_src_moved [03:46:55] [PASSED] drm_test_damage_iter_no_damage_fractional_src_moved [03:46:55] [PASSED] drm_test_damage_iter_no_damage_not_visible [03:46:55] [PASSED] drm_test_damage_iter_no_damage_no_crtc [03:46:55] [PASSED] drm_test_damage_iter_no_damage_no_fb [03:46:55] [PASSED] drm_test_damage_iter_simple_damage [03:46:55] [PASSED] drm_test_damage_iter_single_damage [03:46:55] [PASSED] drm_test_damage_iter_single_damage_intersect_src [03:46:55] [PASSED] drm_test_damage_iter_single_damage_outside_src [03:46:55] [PASSED] drm_test_damage_iter_single_damage_fractional_src [03:46:55] [PASSED] drm_test_damage_iter_single_damage_intersect_fractional_src [03:46:55] [PASSED] drm_test_damage_iter_single_damage_outside_fractional_src [03:46:55] [PASSED] drm_test_damage_iter_single_damage_src_moved [03:46:55] [PASSED] drm_test_damage_iter_single_damage_fractional_src_moved [03:46:55] [PASSED] drm_test_damage_iter_damage [03:46:55] [PASSED] drm_test_damage_iter_damage_one_intersect [03:46:55] [PASSED] drm_test_damage_iter_damage_one_outside [03:46:55] [PASSED] drm_test_damage_iter_damage_src_moved [03:46:55] [PASSED] drm_test_damage_iter_damage_not_visible [03:46:55] ================ [PASSED] drm_damage_helper ================ [03:46:55] ============== drm_dp_mst_helper (3 subtests) ============== [03:46:55] ============== drm_test_dp_mst_calc_pbn_mode ============== [03:46:55] [PASSED] Clock 154000 BPP 30 DSC disabled [03:46:55] [PASSED] Clock 234000 BPP 30 DSC disabled [03:46:55] [PASSED] Clock 297000 BPP 24 DSC disabled [03:46:55] [PASSED] Clock 332880 BPP 24 DSC enabled [03:46:55] [PASSED] Clock 324540 BPP 24 DSC enabled [03:46:55] ========== [PASSED] drm_test_dp_mst_calc_pbn_mode ========== [03:46:55] ============== drm_test_dp_mst_calc_pbn_div =============== [03:46:55] [PASSED] Link rate 2000000 lane count 4 [03:46:55] [PASSED] Link rate 2000000 lane count 2 [03:46:55] [PASSED] Link rate 2000000 lane count 1 [03:46:55] [PASSED] Link rate 1350000 lane count 4 [03:46:55] [PASSED] Link rate 1350000 lane count 2 [03:46:55] [PASSED] Link rate 1350000 lane count 1 [03:46:55] [PASSED] Link rate 1000000 lane count 4 [03:46:55] [PASSED] Link rate 1000000 lane count 2 [03:46:55] [PASSED] Link rate 1000000 lane count 1 [03:46:55] [PASSED] Link rate 810000 lane count 4 [03:46:55] [PASSED] Link rate 810000 lane count 2 [03:46:55] [PASSED] Link rate 810000 lane count 1 [03:46:55] [PASSED] Link rate 540000 lane count 4 [03:46:55] [PASSED] Link rate 540000 lane count 2 [03:46:55] [PASSED] Link rate 540000 lane count 1 [03:46:55] [PASSED] Link rate 270000 lane count 4 [03:46:55] [PASSED] Link rate 270000 lane count 2 [03:46:55] [PASSED] Link rate 270000 lane count 1 [03:46:55] [PASSED] Link rate 162000 lane count 4 [03:46:55] [PASSED] Link rate 162000 lane count 2 [03:46:55] [PASSED] Link rate 162000 lane count 1 [03:46:55] ========== [PASSED] drm_test_dp_mst_calc_pbn_div =========== [03:46:55] ========= drm_test_dp_mst_sideband_msg_req_decode ========= [03:46:55] [PASSED] DP_ENUM_PATH_RESOURCES with port number [03:46:55] [PASSED] DP_POWER_UP_PHY with port number [03:46:55] [PASSED] DP_POWER_DOWN_PHY with port number [03:46:55] [PASSED] DP_ALLOCATE_PAYLOAD with SDP stream sinks [03:46:55] [PASSED] DP_ALLOCATE_PAYLOAD with port number [03:46:55] [PASSED] DP_ALLOCATE_PAYLOAD with VCPI [03:46:55] [PASSED] DP_ALLOCATE_PAYLOAD with PBN [03:46:55] [PASSED] DP_QUERY_PAYLOAD with port number [03:46:55] [PASSED] DP_QUERY_PAYLOAD with VCPI [03:46:55] [PASSED] DP_REMOTE_DPCD_READ with port number [03:46:55] [PASSED] DP_REMOTE_DPCD_READ with DPCD address [03:46:55] [PASSED] DP_REMOTE_DPCD_READ with max number of bytes [03:46:55] [PASSED] DP_REMOTE_DPCD_WRITE with port number [03:46:55] [PASSED] DP_REMOTE_DPCD_WRITE with DPCD address [03:46:55] [PASSED] DP_REMOTE_DPCD_WRITE with data array [03:46:55] [PASSED] DP_REMOTE_I2C_READ with port number [03:46:55] [PASSED] DP_REMOTE_I2C_READ with I2C device ID [03:46:55] [PASSED] DP_REMOTE_I2C_READ with transactions array [03:46:55] [PASSED] DP_REMOTE_I2C_WRITE with port number [03:46:55] [PASSED] DP_REMOTE_I2C_WRITE with I2C device ID [03:46:55] [PASSED] DP_REMOTE_I2C_WRITE with data array [03:46:55] [PASSED] DP_QUERY_STREAM_ENC_STATUS with stream ID [03:46:55] [PASSED] DP_QUERY_STREAM_ENC_STATUS with client ID [03:46:55] [PASSED] DP_QUERY_STREAM_ENC_STATUS with stream event [03:46:55] [PASSED] DP_QUERY_STREAM_ENC_STATUS with valid stream event [03:46:55] [PASSED] DP_QUERY_STREAM_ENC_STATUS with stream behavior [03:46:55] [PASSED] DP_QUERY_STREAM_ENC_STATUS with a valid stream behavior [03:46:55] ===== [PASSED] drm_test_dp_mst_sideband_msg_req_decode ===== [03:46:55] ================ [PASSED] drm_dp_mst_helper ================ [03:46:55] ================== drm_exec (7 subtests) =================== [03:46:55] [PASSED] sanitycheck [03:46:55] [PASSED] test_lock [03:46:55] [PASSED] test_lock_unlock [03:46:55] [PASSED] test_duplicates [03:46:55] [PASSED] test_prepare [03:46:55] [PASSED] test_prepare_array [03:46:55] [PASSED] test_multiple_loops [03:46:55] ==================== [PASSED] drm_exec ===================== [03:46:55] =========== drm_format_helper_test (17 subtests) =========== [03:46:55] ============== drm_test_fb_xrgb8888_to_gray8 ============== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ========== [PASSED] drm_test_fb_xrgb8888_to_gray8 ========== [03:46:55] ============= drm_test_fb_xrgb8888_to_rgb332 ============== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ========= [PASSED] drm_test_fb_xrgb8888_to_rgb332 ========== [03:46:55] ============= drm_test_fb_xrgb8888_to_rgb565 ============== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ========= [PASSED] drm_test_fb_xrgb8888_to_rgb565 ========== [03:46:55] ============ drm_test_fb_xrgb8888_to_xrgb1555 ============= [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======== [PASSED] drm_test_fb_xrgb8888_to_xrgb1555 ========= [03:46:55] ============ drm_test_fb_xrgb8888_to_argb1555 ============= [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======== [PASSED] drm_test_fb_xrgb8888_to_argb1555 ========= [03:46:55] ============ drm_test_fb_xrgb8888_to_rgba5551 ============= [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======== [PASSED] drm_test_fb_xrgb8888_to_rgba5551 ========= [03:46:55] ============= drm_test_fb_xrgb8888_to_rgb888 ============== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ========= [PASSED] drm_test_fb_xrgb8888_to_rgb888 ========== [03:46:55] ============= drm_test_fb_xrgb8888_to_bgr888 ============== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ========= [PASSED] drm_test_fb_xrgb8888_to_bgr888 ========== [03:46:55] ============ drm_test_fb_xrgb8888_to_argb8888 ============= [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======== [PASSED] drm_test_fb_xrgb8888_to_argb8888 ========= [03:46:55] =========== drm_test_fb_xrgb8888_to_xrgb2101010 =========== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======= [PASSED] drm_test_fb_xrgb8888_to_xrgb2101010 ======= [03:46:55] =========== drm_test_fb_xrgb8888_to_argb2101010 =========== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======= [PASSED] drm_test_fb_xrgb8888_to_argb2101010 ======= [03:46:55] ============== drm_test_fb_xrgb8888_to_mono =============== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ========== [PASSED] drm_test_fb_xrgb8888_to_mono =========== [03:46:55] ==================== drm_test_fb_swab ===================== [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ================ [PASSED] drm_test_fb_swab ================= [03:46:55] ============ drm_test_fb_xrgb8888_to_xbgr8888 ============= [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======== [PASSED] drm_test_fb_xrgb8888_to_xbgr8888 ========= [03:46:55] ============ drm_test_fb_xrgb8888_to_abgr8888 ============= [03:46:55] [PASSED] single_pixel_source_buffer [03:46:55] [PASSED] single_pixel_clip_rectangle [03:46:55] [PASSED] well_known_colors [03:46:55] [PASSED] destination_pitch [03:46:55] ======== [PASSED] drm_test_fb_xrgb8888_to_abgr8888 ========= [03:46:55] ================= drm_test_fb_clip_offset ================= [03:46:55] [PASSED] pass through [03:46:55] [PASSED] horizontal offset [03:46:55] [PASSED] vertical offset [03:46:55] [PASSED] horizontal and vertical offset [03:46:55] [PASSED] horizontal offset (custom pitch) [03:46:55] [PASSED] vertical offset (custom pitch) [03:46:55] [PASSED] horizontal and vertical offset (custom pitch) [03:46:55] ============= [PASSED] drm_test_fb_clip_offset ============= [03:46:55] =================== drm_test_fb_memcpy ==================== [03:46:55] [PASSED] single_pixel_source_buffer: XR24 little-endian (0x34325258) [03:46:55] [PASSED] single_pixel_source_buffer: XRA8 little-endian (0x38415258) [03:46:55] [PASSED] single_pixel_source_buffer: YU24 little-endian (0x34325559) [03:46:55] [PASSED] single_pixel_clip_rectangle: XB24 little-endian (0x34324258) [03:46:55] [PASSED] single_pixel_clip_rectangle: XRA8 little-endian (0x38415258) [03:46:55] [PASSED] single_pixel_clip_rectangle: YU24 little-endian (0x34325559) [03:46:55] [PASSED] well_known_colors: XB24 little-endian (0x34324258) [03:46:55] [PASSED] well_known_colors: XRA8 little-endian (0x38415258) [03:46:55] [PASSED] well_known_colors: YU24 little-endian (0x34325559) [03:46:55] [PASSED] destination_pitch: XB24 little-endian (0x34324258) [03:46:55] [PASSED] destination_pitch: XRA8 little-endian (0x38415258) [03:46:55] [PASSED] destination_pitch: YU24 little-endian (0x34325559) [03:46:55] =============== [PASSED] drm_test_fb_memcpy ================ [03:46:55] ============= [PASSED] drm_format_helper_test ============== [03:46:55] ================= drm_format (18 subtests) ================= [03:46:55] [PASSED] drm_test_format_block_width_invalid [03:46:55] [PASSED] drm_test_format_block_width_one_plane [03:46:55] [PASSED] drm_test_format_block_width_two_plane [03:46:55] [PASSED] drm_test_format_block_width_three_plane [03:46:55] [PASSED] drm_test_format_block_width_tiled [03:46:55] [PASSED] drm_test_format_block_height_invalid [03:46:55] [PASSED] drm_test_format_block_height_one_plane [03:46:55] [PASSED] drm_test_format_block_height_two_plane [03:46:55] [PASSED] drm_test_format_block_height_three_plane [03:46:55] [PASSED] drm_test_format_block_height_tiled [03:46:55] [PASSED] drm_test_format_min_pitch_invalid [03:46:55] [PASSED] drm_test_format_min_pitch_one_plane_8bpp [03:46:55] [PASSED] drm_test_format_min_pitch_one_plane_16bpp [03:46:55] [PASSED] drm_test_format_min_pitch_one_plane_24bpp [03:46:55] [PASSED] drm_test_format_min_pitch_one_plane_32bpp [03:46:55] [PASSED] drm_test_format_min_pitch_two_plane [03:46:55] [PASSED] drm_test_format_min_pitch_three_plane_8bpp [03:46:55] [PASSED] drm_test_format_min_pitch_tiled [03:46:55] =================== [PASSED] drm_format ==================== [03:46:55] ============== drm_framebuffer (10 subtests) =============== [03:46:55] ========== drm_test_framebuffer_check_src_coords ========== [03:46:55] [PASSED] Success: source fits into fb [03:46:55] [PASSED] Fail: overflowing fb with x-axis coordinate [03:46:55] [PASSED] Fail: overflowing fb with y-axis coordinate [03:46:55] [PASSED] Fail: overflowing fb with source width [03:46:55] [PASSED] Fail: overflowing fb with source height [03:46:55] ====== [PASSED] drm_test_framebuffer_check_src_coords ====== [03:46:55] [PASSED] drm_test_framebuffer_cleanup [03:46:55] =============== drm_test_framebuffer_create =============== [03:46:55] [PASSED] ABGR8888 normal sizes [03:46:55] [PASSED] ABGR8888 max sizes [03:46:55] [PASSED] ABGR8888 pitch greater than min required [03:46:55] [PASSED] ABGR8888 pitch less than min required [03:46:55] [PASSED] ABGR8888 Invalid width [03:46:55] [PASSED] ABGR8888 Invalid buffer handle [03:46:55] [PASSED] No pixel format [03:46:55] [PASSED] ABGR8888 Width 0 [03:46:55] [PASSED] ABGR8888 Height 0 [03:46:55] [PASSED] ABGR8888 Out of bound height * pitch combination [03:46:55] [PASSED] ABGR8888 Large buffer offset [03:46:55] [PASSED] ABGR8888 Buffer offset for inexistent plane [03:46:55] [PASSED] ABGR8888 Invalid flag [03:46:55] [PASSED] ABGR8888 Set DRM_MODE_FB_MODIFIERS without modifiers [03:46:55] [PASSED] ABGR8888 Valid buffer modifier [03:46:55] [PASSED] ABGR8888 Invalid buffer modifier(DRM_FORMAT_MOD_SAMSUNG_64_32_TILE) [03:46:55] [PASSED] ABGR8888 Extra pitches without DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] ABGR8888 Extra pitches with DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] NV12 Normal sizes [03:46:55] [PASSED] NV12 Max sizes [03:46:55] [PASSED] NV12 Invalid pitch [03:46:55] [PASSED] NV12 Invalid modifier/missing DRM_MODE_FB_MODIFIERS flag [03:46:55] [PASSED] NV12 different modifier per-plane [03:46:55] [PASSED] NV12 with DRM_FORMAT_MOD_SAMSUNG_64_32_TILE [03:46:55] [PASSED] NV12 Valid modifiers without DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] NV12 Modifier for inexistent plane [03:46:55] [PASSED] NV12 Handle for inexistent plane [03:46:55] [PASSED] NV12 Handle for inexistent plane without DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] YVU420 DRM_MODE_FB_MODIFIERS set without modifier [03:46:55] [PASSED] YVU420 Normal sizes [03:46:55] [PASSED] YVU420 Max sizes [03:46:55] [PASSED] YVU420 Invalid pitch [03:46:55] [PASSED] YVU420 Different pitches [03:46:55] [PASSED] YVU420 Different buffer offsets/pitches [03:46:55] [PASSED] YVU420 Modifier set just for plane 0, without DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] YVU420 Modifier set just for planes 0, 1, without DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] YVU420 Modifier set just for plane 0, 1, with DRM_MODE_FB_MODIFIERS [03:46:55] [PASSED] YVU420 Valid modifier [03:46:55] [PASSED] YVU420 Different modifiers per plane [03:46:55] [PASSED] YVU420 Modifier for inexistent plane [03:46:55] [PASSED] YUV420_10BIT Invalid modifier(DRM_FORMAT_MOD_LINEAR) [03:46:55] [PASSED] X0L2 Normal sizes [03:46:55] [PASSED] X0L2 Max sizes [03:46:55] [PASSED] X0L2 Invalid pitch [03:46:55] [PASSED] X0L2 Pitch greater than minimum required [03:46:55] [PASSED] X0L2 Handle for inexistent plane [03:46:55] [PASSED] X0L2 Offset for inexistent plane, without DRM_MODE_FB_MODIFIERS set [03:46:55] [PASSED] X0L2 Modifier without DRM_MODE_FB_MODIFIERS set [03:46:55] [PASSED] X0L2 Valid modifier [03:46:55] [PASSED] X0L2 Modifier for inexistent plane [03:46:55] =========== [PASSED] drm_test_framebuffer_create =========== [03:46:55] [PASSED] drm_test_framebuffer_free [03:46:55] [PASSED] drm_test_framebuffer_init [03:46:55] [PASSED] drm_test_framebuffer_init_bad_format [03:46:55] [PASSED] drm_test_framebuffer_init_dev_mismatch [03:46:55] [PASSED] drm_test_framebuffer_lookup [03:46:55] [PASSED] drm_test_framebuffer_lookup_inexistent [03:46:55] [PASSED] drm_test_framebuffer_modifiers_not_supported [03:46:55] ================= [PASSED] drm_framebuffer ================= [03:46:55] ================ drm_gem_shmem (8 subtests) ================ [03:46:55] [PASSED] drm_gem_shmem_test_obj_create [03:46:55] [PASSED] drm_gem_shmem_test_obj_create_private [03:46:55] [PASSED] drm_gem_shmem_test_pin_pages [03:46:55] [PASSED] drm_gem_shmem_test_vmap [03:46:55] [PASSED] drm_gem_shmem_test_get_pages_sgt [03:46:55] [PASSED] drm_gem_shmem_test_get_sg_table [03:46:55] [PASSED] drm_gem_shmem_test_madvise [03:46:55] [PASSED] drm_gem_shmem_test_purge [03:46:55] ================== [PASSED] drm_gem_shmem ================== [03:46:55] === drm_atomic_helper_connector_hdmi_check (27 subtests) === [03:46:55] [PASSED] drm_test_check_broadcast_rgb_auto_cea_mode [03:46:55] [PASSED] drm_test_check_broadcast_rgb_auto_cea_mode_vic_1 [03:46:55] [PASSED] drm_test_check_broadcast_rgb_full_cea_mode [03:46:55] [PASSED] drm_test_check_broadcast_rgb_full_cea_mode_vic_1 [03:46:55] [PASSED] drm_test_check_broadcast_rgb_limited_cea_mode [03:46:55] [PASSED] drm_test_check_broadcast_rgb_limited_cea_mode_vic_1 [03:46:55] ====== drm_test_check_broadcast_rgb_cea_mode_yuv420 ======= [03:46:55] [PASSED] Automatic [03:46:55] [PASSED] Full [03:46:55] [PASSED] Limited 16:235 [03:46:55] == [PASSED] drm_test_check_broadcast_rgb_cea_mode_yuv420 === [03:46:55] [PASSED] drm_test_check_broadcast_rgb_crtc_mode_changed [03:46:55] [PASSED] drm_test_check_broadcast_rgb_crtc_mode_not_changed [03:46:55] [PASSED] drm_test_check_disable_connector [03:46:55] [PASSED] drm_test_check_hdmi_funcs_reject_rate [03:46:55] [PASSED] drm_test_check_max_tmds_rate_bpc_fallback_rgb [03:46:55] [PASSED] drm_test_check_max_tmds_rate_bpc_fallback_yuv420 [03:46:55] [PASSED] drm_test_check_max_tmds_rate_bpc_fallback_ignore_yuv422 [03:46:55] [PASSED] drm_test_check_max_tmds_rate_bpc_fallback_ignore_yuv420 [03:46:55] [PASSED] drm_test_check_driver_unsupported_fallback_yuv420 [03:46:55] [PASSED] drm_test_check_output_bpc_crtc_mode_changed [03:46:55] [PASSED] drm_test_check_output_bpc_crtc_mode_not_changed [03:46:55] [PASSED] drm_test_check_output_bpc_dvi [03:46:55] [PASSED] drm_test_check_output_bpc_format_vic_1 [03:46:55] [PASSED] drm_test_check_output_bpc_format_display_8bpc_only [03:46:55] [PASSED] drm_test_check_output_bpc_format_display_rgb_only [03:46:55] [PASSED] drm_test_check_output_bpc_format_driver_8bpc_only [03:46:55] [PASSED] drm_test_check_output_bpc_format_driver_rgb_only [03:46:55] [PASSED] drm_test_check_tmds_char_rate_rgb_8bpc [03:46:55] [PASSED] drm_test_check_tmds_char_rate_rgb_10bpc [03:46:55] [PASSED] drm_test_check_tmds_char_rate_rgb_12bpc [03:46:55] ===== [PASSED] drm_atomic_helper_connector_hdmi_check ====== [03:46:55] === drm_atomic_helper_connector_hdmi_reset (6 subtests) ==== [03:46:55] [PASSED] drm_test_check_broadcast_rgb_value [03:46:55] [PASSED] drm_test_check_bpc_8_value [03:46:55] [PASSED] drm_test_check_bpc_10_value [03:46:55] [PASSED] drm_test_check_bpc_12_value [03:46:55] [PASSED] drm_test_check_format_value [03:46:55] [PASSED] drm_test_check_tmds_char_value [03:46:55] ===== [PASSED] drm_atomic_helper_connector_hdmi_reset ====== [03:46:55] = drm_atomic_helper_connector_hdmi_mode_valid (4 subtests) = [03:46:55] [PASSED] drm_test_check_mode_valid [03:46:55] [PASSED] drm_test_check_mode_valid_reject [03:46:55] [PASSED] drm_test_check_mode_valid_reject_rate [03:46:55] [PASSED] drm_test_check_mode_valid_reject_max_clock [03:46:55] === [PASSED] drm_atomic_helper_connector_hdmi_mode_valid === [03:46:55] ================= drm_managed (2 subtests) ================= [03:46:55] [PASSED] drm_test_managed_release_action [03:46:55] [PASSED] drm_test_managed_run_action [03:46:55] =================== [PASSED] drm_managed =================== [03:46:55] =================== drm_mm (6 subtests) ==================== [03:46:55] [PASSED] drm_test_mm_init [03:46:55] [PASSED] drm_test_mm_debug [03:46:55] [PASSED] drm_test_mm_align32 [03:46:55] [PASSED] drm_test_mm_align64 [03:46:55] [PASSED] drm_test_mm_lowest [03:46:55] [PASSED] drm_test_mm_highest [03:46:55] ===================== [PASSED] drm_mm ====================== [03:46:55] ============= drm_modes_analog_tv (5 subtests) ============= [03:46:55] [PASSED] drm_test_modes_analog_tv_mono_576i [03:46:55] [PASSED] drm_test_modes_analog_tv_ntsc_480i [03:46:55] [PASSED] drm_test_modes_analog_tv_ntsc_480i_inlined [03:46:55] [PASSED] drm_test_modes_analog_tv_pal_576i [03:46:55] [PASSED] drm_test_modes_analog_tv_pal_576i_inlined [03:46:55] =============== [PASSED] drm_modes_analog_tv =============== [03:46:55] ============== drm_plane_helper (2 subtests) =============== [03:46:55] =============== drm_test_check_plane_state ================ [03:46:55] [PASSED] clipping_simple [03:46:55] [PASSED] clipping_rotate_reflect [03:46:55] [PASSED] positioning_simple [03:46:55] [PASSED] upscaling [03:46:55] [PASSED] downscaling [03:46:55] [PASSED] rounding1 [03:46:55] [PASSED] rounding2 [03:46:55] [PASSED] rounding3 [03:46:55] [PASSED] rounding4 [03:46:55] =========== [PASSED] drm_test_check_plane_state ============ [03:46:55] =========== drm_test_check_invalid_plane_state ============ [03:46:55] [PASSED] positioning_invalid [03:46:55] [PASSED] upscaling_invalid [03:46:55] [PASSED] downscaling_invalid [03:46:55] ======= [PASSED] drm_test_check_invalid_plane_state ======== [03:46:55] ================ [PASSED] drm_plane_helper ================= [03:46:55] ====== drm_connector_helper_tv_get_modes (1 subtest) ======= [03:46:55] ====== drm_test_connector_helper_tv_get_modes_check ======= [03:46:55] [PASSED] None [03:46:55] [PASSED] PAL [03:46:55] [PASSED] NTSC [03:46:55] [PASSED] Both, NTSC Default [03:46:55] [PASSED] Both, PAL Default [03:46:55] [PASSED] Both, NTSC Default, with PAL on command-line [03:46:55] [PASSED] Both, PAL Default, with NTSC on command-line [03:46:55] == [PASSED] drm_test_connector_helper_tv_get_modes_check === [03:46:55] ======== [PASSED] drm_connector_helper_tv_get_modes ======== [03:46:55] ================== drm_rect (9 subtests) =================== [03:46:55] [PASSED] drm_test_rect_clip_scaled_div_by_zero [03:46:55] [PASSED] drm_test_rect_clip_scaled_not_clipped [03:46:55] [PASSED] drm_test_rect_clip_scaled_clipped [03:46:55] [PASSED] drm_test_rect_clip_scaled_signed_vs_unsigned [03:46:55] ================= drm_test_rect_intersect ================= [03:46:55] [PASSED] top-left x bottom-right: 2x2+1+1 x 2x2+0+0 [03:46:55] [PASSED] top-right x bottom-left: 2x2+0+0 x 2x2+1-1 [03:46:55] [PASSED] bottom-left x top-right: 2x2+1-1 x 2x2+0+0 [03:46:55] [PASSED] bottom-right x top-left: 2x2+0+0 x 2x2+1+1 [03:46:55] [PASSED] right x left: 2x1+0+0 x 3x1+1+0 [03:46:55] [PASSED] left x right: 3x1+1+0 x 2x1+0+0 [03:46:55] [PASSED] up x bottom: 1x2+0+0 x 1x3+0-1 [03:46:55] [PASSED] bottom x up: 1x3+0-1 x 1x2+0+0 [03:46:55] [PASSED] touching corner: 1x1+0+0 x 2x2+1+1 [03:46:55] [PASSED] touching side: 1x1+0+0 x 1x1+1+0 [03:46:55] [PASSED] equal rects: 2x2+0+0 x 2x2+0+0 [03:46:55] [PASSED] inside another: 2x2+0+0 x 1x1+1+1 [03:46:55] [PASSED] far away: 1x1+0+0 x 1x1+3+6 [03:46:55] [PASSED] points intersecting: 0x0+5+10 x 0x0+5+10 [03:46:55] [PASSED] points not intersecting: 0x0+0+0 x 0x0+5+10 [03:46:55] ============= [PASSED] drm_test_rect_intersect ============= [03:46:55] ================ drm_test_rect_calc_hscale ================ [03:46:55] [PASSED] normal use [03:46:55] [PASSED] out of max range [03:46:55] [PASSED] out of min range [03:46:55] [PASSED] zero dst [03:46:55] [PASSED] negative src [03:46:55] [PASSED] negative dst [03:46:55] ============ [PASSED] drm_test_rect_calc_hscale ============ [03:46:55] ================ drm_test_rect_calc_vscale ================ [03:46:55] [PASSED] normal use stty: 'standard input': Inappropriate ioctl for device [03:46:55] [PASSED] out of max range [03:46:55] [PASSED] out of min range [03:46:55] [PASSED] zero dst [03:46:55] [PASSED] negative src [03:46:55] [PASSED] negative dst [03:46:55] ============ [PASSED] drm_test_rect_calc_vscale ============ [03:46:55] ================== drm_test_rect_rotate =================== [03:46:55] [PASSED] reflect-x [03:46:55] [PASSED] reflect-y [03:46:55] [PASSED] rotate-0 [03:46:55] [PASSED] rotate-90 [03:46:55] [PASSED] rotate-180 [03:46:55] [PASSED] rotate-270 [03:46:55] ============== [PASSED] drm_test_rect_rotate =============== [03:46:55] ================ drm_test_rect_rotate_inv ================= [03:46:55] [PASSED] reflect-x [03:46:55] [PASSED] reflect-y [03:46:55] [PASSED] rotate-0 [03:46:55] [PASSED] rotate-90 [03:46:55] [PASSED] rotate-180 [03:46:55] [PASSED] rotate-270 [03:46:55] ============ [PASSED] drm_test_rect_rotate_inv ============= [03:46:55] ==================== [PASSED] drm_rect ===================== [03:46:55] ============ drm_sysfb_modeset_test (1 subtest) ============ [03:46:55] ============ drm_test_sysfb_build_fourcc_list ============= [03:46:55] [PASSED] no native formats [03:46:55] [PASSED] XRGB8888 as native format [03:46:55] [PASSED] remove duplicates [03:46:55] [PASSED] convert alpha formats [03:46:55] [PASSED] random formats [03:46:55] ======== [PASSED] drm_test_sysfb_build_fourcc_list ========= [03:46:55] ============= [PASSED] drm_sysfb_modeset_test ============== [03:46:55] ============================================================ [03:46:55] Testing complete. Ran 622 tests: passed: 622 [03:46:55] Elapsed time: 26.886s total, 1.744s configuring, 24.725s building, 0.386s running
+ /kernel/tools/testing/kunit/kunit.py run --kunitconfig /kernel/drivers/gpu/drm/ttm/tests/.kunitconfig [03:46:55] Configuring KUnit Kernel ...
Regenerating .config ...
Populating config with:
$ make ARCH=um O=.kunit olddefconfig [03:46:57] Building KUnit Kernel ... Populating config with: $ make ARCH=um O=.kunit olddefconfig Building with: $ make all compile_commands.json scripts_gdb ARCH=um O=.kunit --jobs=48 [03:47:06] Starting KUnit Kernel (1/1)... [03:47:06] ============================================================ Running tests with: $ .kunit/linux kunit.enable=1 mem=1G console=tty kunit_shutdown=halt [03:47:06] ================= ttm_device (5 subtests) ================== [03:47:06] [PASSED] ttm_device_init_basic [03:47:06] [PASSED] ttm_device_init_multiple [03:47:06] [PASSED] ttm_device_fini_basic [03:47:06] [PASSED] ttm_device_init_no_vma_man [03:47:06] ================== ttm_device_init_pools ================== [03:47:06] [PASSED] No DMA allocations, no DMA32 required [03:47:06] [PASSED] DMA allocations, DMA32 required [03:47:06] [PASSED] No DMA allocations, DMA32 required [03:47:06] [PASSED] DMA allocations, no DMA32 required [03:47:06] ============== [PASSED] ttm_device_init_pools ============== [03:47:06] =================== [PASSED] ttm_device ==================== [03:47:06] ================== ttm_pool (8 subtests) =================== [03:47:06] ================== ttm_pool_alloc_basic =================== [03:47:06] [PASSED] One page [03:47:06] [PASSED] More than one page [03:47:06] [PASSED] Above the allocation limit [03:47:06] [PASSED] One page, with coherent DMA mappings enabled [03:47:06] [PASSED] Above the allocation limit, with coherent DMA mappings enabled [03:47:06] ============== [PASSED] ttm_pool_alloc_basic =============== [03:47:06] ============== ttm_pool_alloc_basic_dma_addr ============== [03:47:06] [PASSED] One page [03:47:06] [PASSED] More than one page [03:47:06] [PASSED] Above the allocation limit [03:47:06] [PASSED] One page, with coherent DMA mappings enabled [03:47:06] [PASSED] Above the allocation limit, with coherent DMA mappings enabled [03:47:06] ========== [PASSED] ttm_pool_alloc_basic_dma_addr ========== [03:47:06] [PASSED] ttm_pool_alloc_order_caching_match [03:47:06] [PASSED] ttm_pool_alloc_caching_mismatch [03:47:06] [PASSED] ttm_pool_alloc_order_mismatch [03:47:06] [PASSED] ttm_pool_free_dma_alloc [03:47:06] [PASSED] ttm_pool_free_no_dma_alloc [03:47:06] [PASSED] ttm_pool_fini_basic [03:47:06] ==================== [PASSED] ttm_pool ===================== [03:47:06] ================ ttm_resource (8 subtests) ================= [03:47:06] ================= ttm_resource_init_basic ================= [03:47:06] [PASSED] Init resource in TTM_PL_SYSTEM [03:47:06] [PASSED] Init resource in TTM_PL_VRAM [03:47:06] [PASSED] Init resource in a private placement [03:47:06] [PASSED] Init resource in TTM_PL_SYSTEM, set placement flags [03:47:06] ============= [PASSED] ttm_resource_init_basic ============= [03:47:06] [PASSED] ttm_resource_init_pinned [03:47:06] [PASSED] ttm_resource_fini_basic [03:47:06] [PASSED] ttm_resource_manager_init_basic [03:47:06] [PASSED] ttm_resource_manager_usage_basic [03:47:06] [PASSED] ttm_resource_manager_set_used_basic [03:47:06] [PASSED] ttm_sys_man_alloc_basic [03:47:06] [PASSED] ttm_sys_man_free_basic [03:47:06] ================== [PASSED] ttm_resource =================== [03:47:06] =================== ttm_tt (15 subtests) =================== [03:47:06] ==================== ttm_tt_init_basic ==================== [03:47:06] [PASSED] Page-aligned size [03:47:06] [PASSED] Extra pages requested [03:47:06] ================ [PASSED] ttm_tt_init_basic ================ [03:47:06] [PASSED] ttm_tt_init_misaligned [03:47:06] [PASSED] ttm_tt_fini_basic [03:47:06] [PASSED] ttm_tt_fini_sg [03:47:06] [PASSED] ttm_tt_fini_shmem [03:47:06] [PASSED] ttm_tt_create_basic [03:47:06] [PASSED] ttm_tt_create_invalid_bo_type [03:47:06] [PASSED] ttm_tt_create_ttm_exists [03:47:06] [PASSED] ttm_tt_create_failed [03:47:06] [PASSED] ttm_tt_destroy_basic [03:47:06] [PASSED] ttm_tt_populate_null_ttm [03:47:06] [PASSED] ttm_tt_populate_populated_ttm [03:47:06] [PASSED] ttm_tt_unpopulate_basic [03:47:06] [PASSED] ttm_tt_unpopulate_empty_ttm [03:47:06] [PASSED] ttm_tt_swapin_basic [03:47:06] ===================== [PASSED] ttm_tt ====================== [03:47:06] =================== ttm_bo (14 subtests) =================== [03:47:06] =========== ttm_bo_reserve_optimistic_no_ticket =========== [03:47:06] [PASSED] Cannot be interrupted and sleeps [03:47:06] [PASSED] Cannot be interrupted, locks straight away [03:47:06] [PASSED] Can be interrupted, sleeps [03:47:06] ======= [PASSED] ttm_bo_reserve_optimistic_no_ticket ======= [03:47:06] [PASSED] ttm_bo_reserve_locked_no_sleep [03:47:06] [PASSED] ttm_bo_reserve_no_wait_ticket [03:47:06] [PASSED] ttm_bo_reserve_double_resv [03:47:06] [PASSED] ttm_bo_reserve_interrupted [03:47:06] [PASSED] ttm_bo_reserve_deadlock [03:47:06] [PASSED] ttm_bo_unreserve_basic [03:47:06] [PASSED] ttm_bo_unreserve_pinned [03:47:06] [PASSED] ttm_bo_unreserve_bulk [03:47:06] [PASSED] ttm_bo_fini_basic [03:47:06] [PASSED] ttm_bo_fini_shared_resv [03:47:06] [PASSED] ttm_bo_pin_basic [03:47:06] [PASSED] ttm_bo_pin_unpin_resource [03:47:06] [PASSED] ttm_bo_multiple_pin_one_unpin [03:47:06] ===================== [PASSED] ttm_bo ====================== [03:47:06] ============== ttm_bo_validate (21 subtests) =============== [03:47:06] ============== ttm_bo_init_reserved_sys_man =============== [03:47:06] [PASSED] Buffer object for userspace [03:47:06] [PASSED] Kernel buffer object [03:47:06] [PASSED] Shared buffer object [03:47:06] ========== [PASSED] ttm_bo_init_reserved_sys_man =========== [03:47:06] ============== ttm_bo_init_reserved_mock_man ============== [03:47:06] [PASSED] Buffer object for userspace [03:47:06] [PASSED] Kernel buffer object [03:47:06] [PASSED] Shared buffer object [03:47:06] ========== [PASSED] ttm_bo_init_reserved_mock_man ========== [03:47:06] [PASSED] ttm_bo_init_reserved_resv [03:47:06] ================== ttm_bo_validate_basic ================== [03:47:06] [PASSED] Buffer object for userspace [03:47:06] [PASSED] Kernel buffer object [03:47:06] [PASSED] Shared buffer object [03:47:06] ============== [PASSED] ttm_bo_validate_basic ============== [03:47:06] [PASSED] ttm_bo_validate_invalid_placement [03:47:06] ============= ttm_bo_validate_same_placement ============== [03:47:06] [PASSED] System manager [03:47:06] [PASSED] VRAM manager [03:47:06] ========= [PASSED] ttm_bo_validate_same_placement ========== [03:47:06] [PASSED] ttm_bo_validate_failed_alloc [03:47:06] [PASSED] ttm_bo_validate_pinned [03:47:06] [PASSED] ttm_bo_validate_busy_placement [03:47:06] ================ ttm_bo_validate_multihop ================= [03:47:06] [PASSED] Buffer object for userspace [03:47:06] [PASSED] Kernel buffer object [03:47:06] [PASSED] Shared buffer object [03:47:06] ============ [PASSED] ttm_bo_validate_multihop ============= [03:47:06] ========== ttm_bo_validate_no_placement_signaled ========== [03:47:06] [PASSED] Buffer object in system domain, no page vector [03:47:06] [PASSED] Buffer object in system domain with an existing page vector [03:47:06] ====== [PASSED] ttm_bo_validate_no_placement_signaled ====== [03:47:06] ======== ttm_bo_validate_no_placement_not_signaled ======== [03:47:06] [PASSED] Buffer object for userspace [03:47:06] [PASSED] Kernel buffer object [03:47:06] [PASSED] Shared buffer object [03:47:06] ==== [PASSED] ttm_bo_validate_no_placement_not_signaled ==== [03:47:06] [PASSED] ttm_bo_validate_move_fence_signaled [03:47:06] ========= ttm_bo_validate_move_fence_not_signaled ========= [03:47:06] [PASSED] Waits for GPU [03:47:06] [PASSED] Tries to lock straight away [03:47:06] ===== [PASSED] ttm_bo_validate_move_fence_not_signaled ===== [03:47:06] [PASSED] ttm_bo_validate_happy_evict [03:47:06] [PASSED] ttm_bo_validate_all_pinned_evict [03:47:06] [PASSED] ttm_bo_validate_allowed_only_evict [03:47:06] [PASSED] ttm_bo_validate_deleted_evict [03:47:06] [PASSED] ttm_bo_validate_busy_domain_evict [03:47:06] [PASSED] ttm_bo_validate_evict_gutting [03:47:06] [PASSED] ttm_bo_validate_recrusive_evict stty: 'standard input': Inappropriate ioctl for device [03:47:06] ================= [PASSED] ttm_bo_validate ================= [03:47:06] ============================================================ [03:47:06] Testing complete. Ran 101 tests: passed: 101 [03:47:06] Elapsed time: 11.412s total, 1.668s configuring, 9.476s building, 0.226s running
+ cleanup
++ stat -c %u:%g /kernel
+ chown -R 1003:1003 /kernel
Patchwork
CI✓ Xe.CI.BAT: success for drm/xe: Add Xe3p support
In reply to Lucas De Marchi== Series Details ==
== Series Details ==
Series: drm/xe: Add Xe3p support
URL : https://patchwork.freedesktop.org/series/155866/
State : success
== Summary ==
CI Bug Log - changes from xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada_BAT -> xe-pw-155866v1_BAT
====================================================
Summary
-------
**SUCCESS**
No regressions found.
Participating hosts (11 -> 11)
------------------------------
No changes in participating hosts
Known issues
------------
Here are the changes found in xe-pw-155866v1_BAT that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@kms_flip@basic-plain-flip@b-edp1:
- bat-adlp-7: [PASS][1] -> [DMESG-WARN][2] ([Intel XE#4543]) +1 other test dmesg-warn
[1]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/bat-adlp-7/igt@kms_flip@[email protected]
[2]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/bat-adlp-7/igt@kms_flip@[email protected]
[Intel XE#4543]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4543
Build changes
-------------
* Linux: xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada -> xe-pw-155866v1
IGT_8582: 8582
xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada: c917f7d11493984be9f381ca0a7667bd3e587ada
xe-pw-155866v1: 155866v1
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/index.html
Patchwork
CI✓ Xe.CI.Full: success for drm/xe: Add Xe3p support
In reply to Lucas De Marchi== Series Details ==
== Series Details ==
Series: drm/xe: Add Xe3p support
URL : https://patchwork.freedesktop.org/series/155866/
State : success
== Summary ==
CI Bug Log - changes from xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada_FULL -> xe-pw-155866v1_FULL
====================================================
Summary
-------
**SUCCESS**
No regressions found.
Participating hosts (4 -> 4)
------------------------------
No changes in participating hosts
Known issues
------------
Here are the changes found in xe-pw-155866v1_FULL that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@intel_hwmon@hwmon-write:
- shard-adlp: NOTRUN -> [SKIP][1] ([Intel XE#1125] / [Intel XE#5574])
[1]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@kms_async_flips@crc-atomic@pipe-d-hdmi-a-1:
- shard-adlp: NOTRUN -> [FAIL][2] ([Intel XE#3884]) +1 other test fail
[2]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@kms_async_flips@[email protected]
* igt@kms_big_fb@linear-16bpp-rotate-270:
- shard-lnl: NOTRUN -> [SKIP][3] ([Intel XE#1407]) +2 other tests skip
[3]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_big_fb@linear-32bpp-rotate-90:
- shard-adlp: NOTRUN -> [SKIP][4] ([Intel XE#316]) +2 other tests skip
[4]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_big_fb@y-tiled-addfb:
- shard-bmg: NOTRUN -> [SKIP][5] ([Intel XE#2328])
[5]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
- shard-dg2-set2: NOTRUN -> [SKIP][6] ([Intel XE#619])
[6]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-433/igt@[email protected]
* igt@kms_big_fb@y-tiled-addfb-size-offset-overflow:
- shard-lnl: NOTRUN -> [SKIP][7] ([Intel XE#1477])
[7]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_big_fb@y-tiled-max-hw-stride-32bpp-rotate-180-async-flip:
- shard-adlp: NOTRUN -> [DMESG-FAIL][8] ([Intel XE#4543]) +10 other tests dmesg-fail
[8]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_big_fb@y-tiled-max-hw-stride-32bpp-rotate-180-async-flip.html
* igt@kms_big_fb@yf-tiled-8bpp-rotate-270:
- shard-lnl: NOTRUN -> [SKIP][9] ([Intel XE#1124]) +1 other test skip
[9]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_big_fb@yf-tiled-addfb-size-offset-overflow:
- shard-adlp: NOTRUN -> [SKIP][10] ([Intel XE#607])
[10]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_big_fb@yf-tiled-addfb-size-overflow:
- shard-adlp: NOTRUN -> [SKIP][11] ([Intel XE#610]) +1 other test skip
[11]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@kms_big_fb@yf-tiled-max-hw-stride-64bpp-rotate-0-hflip-async-flip:
- shard-dg2-set2: NOTRUN -> [SKIP][12] ([Intel XE#1124]) +1 other test skip
[12]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-432/igt@kms_big_fb@yf-tiled-max-hw-stride-64bpp-rotate-0-hflip-async-flip.html
* igt@kms_big_fb@yf-tiled-max-hw-stride-64bpp-rotate-180:
- shard-adlp: NOTRUN -> [SKIP][13] ([Intel XE#1124]) +11 other tests skip
[13]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_bw@connected-linear-tiling-2-displays-1920x1080p:
- shard-bmg: [PASS][14] -> [SKIP][15] ([Intel XE#2314] / [Intel XE#2894]) +1 other test skip
[14]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-3/igt@[email protected]
[15]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_bw@connected-linear-tiling-2-displays-3840x2160p:
- shard-adlp: NOTRUN -> [SKIP][16] ([Intel XE#2191]) +1 other test skip
[16]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@kms_bw@connected-linear-tiling-3-displays-1920x1080p:
- shard-bmg: NOTRUN -> [SKIP][17] ([Intel XE#2314] / [Intel XE#2894])
[17]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
- shard-dg2-set2: NOTRUN -> [SKIP][18] ([Intel XE#2191])
[18]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-433/igt@[email protected]
* igt@kms_bw@linear-tiling-2-displays-1920x1080p:
- shard-adlp: NOTRUN -> [SKIP][19] ([Intel XE#367]) +2 other tests skip
[19]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_bw@linear-tiling-3-displays-2160x1440p:
- shard-lnl: NOTRUN -> [SKIP][20] ([Intel XE#367])
[20]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_ccs@bad-aux-stride-4-tiled-mtl-rc-ccs-cc:
- shard-adlp: NOTRUN -> [SKIP][21] ([Intel XE#455] / [Intel XE#787]) +43 other tests skip
[21]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
- shard-dg2-set2: NOTRUN -> [SKIP][22] ([Intel XE#455] / [Intel XE#787]) +1 other test skip
[22]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@kms_ccs@bad-aux-stride-4-tiled-mtl-rc-ccs-cc@pipe-c-dp-4:
- shard-dg2-set2: NOTRUN -> [SKIP][23] ([Intel XE#787]) +6 other tests skip
[23]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@kms_ccs@[email protected]
* igt@kms_ccs@bad-rotation-90-4-tiled-lnl-ccs@pipe-c-dp-2:
- shard-bmg: NOTRUN -> [SKIP][24] ([Intel XE#2652] / [Intel XE#787]) +3 other tests skip
[24]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@kms_ccs@[email protected]
* igt@kms_ccs@bad-rotation-90-4-tiled-mtl-rc-ccs-cc@pipe-c-hdmi-a-1:
- shard-adlp: NOTRUN -> [SKIP][25] ([Intel XE#787]) +65 other tests skip
[25]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_ccs@[email protected]
* igt@kms_ccs@ccs-on-another-bo-4-tiled-mtl-rc-ccs-cc:
- shard-lnl: NOTRUN -> [SKIP][26] ([Intel XE#2887]) +2 other tests skip
[26]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_ccs@crc-primary-rotation-180-4-tiled-bmg-ccs:
- shard-adlp: NOTRUN -> [SKIP][27] ([Intel XE#2907])
[27]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_ccs@crc-primary-rotation-180-4-tiled-bmg-ccs@pipe-b-edp-1:
- shard-lnl: NOTRUN -> [SKIP][28] ([Intel XE#2669]) +3 other tests skip
[28]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_ccs@[email protected]
* igt@kms_ccs@crc-sprite-planes-basic-4-tiled-lnl-ccs:
- shard-dg2-set2: NOTRUN -> [SKIP][29] ([Intel XE#2907])
[29]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-432/igt@[email protected]
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-mc-ccs@pipe-a-dp-4:
- shard-dg2-set2: [PASS][30] -> [INCOMPLETE][31] ([Intel XE#1727] / [Intel XE#2705] / [Intel XE#3113] / [Intel XE#4212] / [Intel XE#4522])
[30]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-433/igt@kms_ccs@[email protected]
[31]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-466/igt@kms_ccs@[email protected]
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-rc-ccs-cc:
- shard-dg2-set2: [PASS][32] -> [INCOMPLETE][33] ([Intel XE#1727] / [Intel XE#3113] / [Intel XE#4345] / [Intel XE#6168])
[32]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-432/igt@[email protected]
[33]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-466/igt@[email protected]
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-rc-ccs-cc@pipe-c-dp-4:
- shard-dg2-set2: [PASS][34] -> [INCOMPLETE][35] ([Intel XE#6014] / [Intel XE#6168])
[34]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-432/igt@kms_ccs@[email protected]
[35]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-466/igt@kms_ccs@[email protected]
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-rc-ccs-cc@pipe-c-hdmi-a-6:
- shard-dg2-set2: [PASS][36] -> [DMESG-WARN][37] ([Intel XE#1727] / [Intel XE#3113])
[36]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-432/igt@kms_ccs@[email protected]
[37]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-466/igt@kms_ccs@[email protected]
* igt@kms_chamelium_color@ctm-negative:
- shard-lnl: NOTRUN -> [SKIP][38] ([Intel XE#306]) +1 other test skip
[38]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
- shard-adlp: NOTRUN -> [SKIP][39] ([Intel XE#306]) +1 other test skip
[39]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_chamelium_hpd@hdmi-hpd:
- shard-lnl: NOTRUN -> [SKIP][40] ([Intel XE#373])
[40]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_chamelium_hpd@hdmi-hpd-after-hibernate:
- shard-dg2-set2: NOTRUN -> [SKIP][41] ([Intel XE#373])
[41]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@kms_chamelium_hpd@hdmi-hpd-storm-disable:
- shard-adlp: NOTRUN -> [SKIP][42] ([Intel XE#373]) +10 other tests skip
[42]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@kms_content_protection@atomic-dpms@pipe-a-dp-2:
- shard-bmg: NOTRUN -> [FAIL][43] ([Intel XE#1178])
[43]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@kms_content_protection@[email protected]
* igt@kms_content_protection@dp-mst-type-1:
- shard-adlp: NOTRUN -> [SKIP][44] ([Intel XE#307]) +1 other test skip
[44]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@kms_content_protection@mei-interface:
- shard-lnl: NOTRUN -> [SKIP][45] ([Intel XE#1468])
[45]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_cursor_crc@cursor-offscreen-512x512:
- shard-adlp: NOTRUN -> [SKIP][46] ([Intel XE#308])
[46]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_cursor_crc@cursor-random-32x32:
- shard-lnl: NOTRUN -> [SKIP][47] ([Intel XE#1424]) +1 other test skip
[47]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_cursor_legacy@cursorb-vs-flipa-atomic-transitions-varying-size:
- shard-adlp: NOTRUN -> [SKIP][48] ([Intel XE#309]) +5 other tests skip
[48]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@kms_cursor_legacy@cursorb-vs-flipa-atomic-transitions-varying-size.html
- shard-lnl: NOTRUN -> [SKIP][49] ([Intel XE#309])
[49]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_cursor_legacy@cursorb-vs-flipa-atomic-transitions-varying-size.html
* igt@kms_cursor_legacy@cursorb-vs-flipb-atomic-transitions-varying-size:
- shard-bmg: [PASS][50] -> [SKIP][51] ([Intel XE#2291]) +7 other tests skip
[50]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-3/igt@kms_cursor_legacy@cursorb-vs-flipb-atomic-transitions-varying-size.html
[51]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@kms_cursor_legacy@cursorb-vs-flipb-atomic-transitions-varying-size.html
* igt@kms_cursor_legacy@flip-vs-cursor-atomic-transitions:
- shard-bmg: [PASS][52] -> [FAIL][53] ([Intel XE#1475])
[52]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-6/igt@[email protected]
[53]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-5/igt@[email protected]
* igt@kms_cursor_legacy@short-busy-flip-before-cursor-toggle:
- shard-dg2-set2: NOTRUN -> [SKIP][54] ([Intel XE#323])
[54]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
- shard-adlp: NOTRUN -> [SKIP][55] ([Intel XE#323])
[55]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_dither@fb-8bpc-vs-panel-6bpc:
- shard-bmg: [PASS][56] -> [SKIP][57] ([Intel XE#1340])
[56]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[57]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_dp_aux_dev:
- shard-adlp: NOTRUN -> [SKIP][58] ([Intel XE#3009])
[58]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_dp_aux_dev.html
- shard-bmg: [PASS][59] -> [SKIP][60] ([Intel XE#3009])
[59]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-5/igt@kms_dp_aux_dev.html
[60]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@kms_dp_aux_dev.html
* igt@kms_dp_link_training@uhbr-mst:
- shard-lnl: NOTRUN -> [SKIP][61] ([Intel XE#4354])
[61]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
- shard-adlp: NOTRUN -> [SKIP][62] ([Intel XE#4356])
[62]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_dp_linktrain_fallback@dp-fallback:
- shard-adlp: NOTRUN -> [SKIP][63] ([Intel XE#4331])
[63]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_fbc_dirty_rect@fbc-dirty-rectangle-out-visible-area:
- shard-adlp: NOTRUN -> [SKIP][64] ([Intel XE#4422])
[64]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@kms_feature_discovery@psr1:
- shard-adlp: NOTRUN -> [SKIP][65] ([Intel XE#1135])
[65]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_flip@2x-flip-vs-absolute-wf_vblank-interruptible:
- shard-lnl: NOTRUN -> [SKIP][66] ([Intel XE#1421]) +1 other test skip
[66]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_flip@2x-flip-vs-absolute-wf_vblank-interruptible.html
* igt@kms_flip@2x-flip-vs-blocking-wf-vblank:
- shard-adlp: NOTRUN -> [SKIP][67] ([Intel XE#310]) +4 other tests skip
[67]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@kms_flip@2x-single-buffer-flip-vs-dpms-off-vs-modeset:
- shard-bmg: NOTRUN -> [SKIP][68] ([Intel XE#2316])
[68]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_flip@2x-wf_vblank-ts-check-interruptible:
- shard-bmg: [PASS][69] -> [SKIP][70] ([Intel XE#2316]) +2 other tests skip
[69]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@kms_flip@2x-wf_vblank-ts-check-interruptible.html
[70]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@kms_flip@2x-wf_vblank-ts-check-interruptible.html
* igt@kms_flip@flip-vs-expired-vblank-interruptible@a-edp1:
- shard-lnl: [PASS][71] -> [FAIL][72] ([Intel XE#301])
[71]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-lnl-1/igt@kms_flip@[email protected]
[72]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-4/igt@kms_flip@[email protected]
* igt@kms_flip@flip-vs-expired-vblank-interruptible@d-hdmi-a1:
- shard-adlp: NOTRUN -> [DMESG-WARN][73] ([Intel XE#4543]) +5 other tests dmesg-warn
[73]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_flip@[email protected]
* igt@kms_flip@flip-vs-rmfb-interruptible:
- shard-adlp: [PASS][74] -> [DMESG-WARN][75] ([Intel XE#4543] / [Intel XE#5208])
[74]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-9/igt@[email protected]
[75]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-2/igt@[email protected]
* igt@kms_flip@flip-vs-suspend-interruptible:
- shard-adlp: [PASS][76] -> [DMESG-WARN][77] ([Intel XE#4543]) +12 other tests dmesg-warn
[76]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-6/igt@[email protected]
[77]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-2/igt@[email protected]
* igt@kms_flip@flip-vs-wf_vblank-interruptible:
- shard-adlp: [PASS][78] -> [DMESG-WARN][79] ([Intel XE#2953] / [Intel XE#4173] / [Intel XE#4543])
[78]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-2/igt@kms_flip@flip-vs-wf_vblank-interruptible.html
[79]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_flip@flip-vs-wf_vblank-interruptible.html
* igt@kms_flip_scaled_crc@flip-32bpp-yftileccs-to-64bpp-yftile-upscaling:
- shard-adlp: NOTRUN -> [SKIP][80] ([Intel XE#455]) +25 other tests skip
[80]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@kms_flip_scaled_crc@flip-32bpp-yftileccs-to-64bpp-yftile-upscaling.html
- shard-lnl: NOTRUN -> [SKIP][81] ([Intel XE#1401] / [Intel XE#1745]) +1 other test skip
[81]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_flip_scaled_crc@flip-32bpp-yftileccs-to-64bpp-yftile-upscaling.html
* igt@kms_flip_scaled_crc@flip-32bpp-yftileccs-to-64bpp-yftile-upscaling@pipe-a-default-mode:
- shard-lnl: NOTRUN -> [SKIP][82] ([Intel XE#1401]) +1 other test skip
[82]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_flip_scaled_crc@flip-32bpp-yftileccs-to-64bpp-yftile-upscaling@pipe-a-default-mode.html
* igt@kms_flip_scaled_crc@flip-64bpp-ytile-to-16bpp-ytile-downscaling@pipe-a-valid-mode:
- shard-adlp: NOTRUN -> [DMESG-FAIL][83] ([Intel XE#4543] / [Intel XE#4921]) +5 other tests dmesg-fail
[83]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@kms_flip_scaled_crc@flip-64bpp-ytile-to-16bpp-ytile-downscaling@pipe-a-valid-mode.html
* igt@kms_flip_tiling@flip-change-tiling@pipe-b-hdmi-a-1-y-to-x:
- shard-adlp: [PASS][84] -> [DMESG-FAIL][85] ([Intel XE#4543])
[84]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-8/igt@kms_flip_tiling@[email protected]
[85]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@kms_flip_tiling@[email protected]
* igt@kms_frontbuffer_tracking@drrs-1p-primscrn-cur-indfb-draw-blt:
- shard-adlp: NOTRUN -> [SKIP][86] ([Intel XE#651]) +13 other tests skip
[86]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@kms_frontbuffer_tracking@drrs-1p-primscrn-cur-indfb-draw-blt.html
- shard-dg2-set2: NOTRUN -> [SKIP][87] ([Intel XE#651]) +3 other tests skip
[87]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@kms_frontbuffer_tracking@drrs-1p-primscrn-cur-indfb-draw-blt.html
* igt@kms_frontbuffer_tracking@drrs-2p-primscrn-shrfb-msflip-blt:
- shard-bmg: NOTRUN -> [SKIP][88] ([Intel XE#2312]) +1 other test skip
[88]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_frontbuffer_tracking@drrs-2p-primscrn-spr-indfb-draw-render:
- shard-adlp: NOTRUN -> [SKIP][89] ([Intel XE#656]) +49 other tests skip
[89]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_frontbuffer_tracking@drrs-2p-primscrn-spr-indfb-draw-render.html
* igt@kms_frontbuffer_tracking@drrs-suspend:
- shard-lnl: NOTRUN -> [SKIP][90] ([Intel XE#651]) +3 other tests skip
[90]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_frontbuffer_tracking@fbcdrrs-1p-primscrn-pri-shrfb-draw-mmap-wc:
- shard-bmg: NOTRUN -> [SKIP][91] ([Intel XE#2311])
[91]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@kms_frontbuffer_tracking@fbcdrrs-1p-primscrn-pri-shrfb-draw-mmap-wc.html
* igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-pri-indfb-draw-mmap-wc:
- shard-adlp: NOTRUN -> [SKIP][92] ([Intel XE#653]) +14 other tests skip
[92]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-pri-indfb-draw-mmap-wc.html
* igt@kms_frontbuffer_tracking@psr-2p-scndscrn-cur-indfb-move:
- shard-dg2-set2: NOTRUN -> [SKIP][93] ([Intel XE#653])
[93]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@kms_frontbuffer_tracking@psr-2p-scndscrn-pri-indfb-draw-render:
- shard-lnl: NOTRUN -> [SKIP][94] ([Intel XE#656]) +6 other tests skip
[94]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_frontbuffer_tracking@psr-2p-scndscrn-pri-indfb-draw-render.html
* igt@kms_hdr@brightness-with-hdr:
- shard-lnl: NOTRUN -> [SKIP][95] ([Intel XE#3374] / [Intel XE#3544])
[95]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_hdr@static-swap:
- shard-bmg: [PASS][96] -> [SKIP][97] ([Intel XE#1503]) +1 other test skip
[96]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-3/igt@[email protected]
[97]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_joiner@basic-force-big-joiner:
- shard-bmg: [PASS][98] -> [SKIP][99] ([Intel XE#3012])
[98]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-3/igt@[email protected]
[99]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_pipe_stress@stress-xrgb8888-ytiled:
- shard-lnl: NOTRUN -> [SKIP][100] ([Intel XE#4329])
[100]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_pm_backlight@fade-with-suspend:
- shard-adlp: NOTRUN -> [SKIP][101] ([Intel XE#870])
[101]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_pm_dc@dc6-psr:
- shard-bmg: NOTRUN -> [SKIP][102] ([Intel XE#2392])
[102]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_pm_rpm@modeset-non-lpsp-stress:
- shard-adlp: NOTRUN -> [SKIP][103] ([Intel XE#836])
[103]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@kms_pm_rpm@universal-planes:
- shard-adlp: NOTRUN -> [DMESG-WARN][104] ([Intel XE#2953] / [Intel XE#4173] / [Intel XE#5750])
[104]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@kms_pm_rpm@universal-planes@plane-33:
- shard-adlp: NOTRUN -> [DMESG-WARN][105] ([Intel XE#2953] / [Intel XE#4173])
[105]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_pm_rpm@[email protected]
* igt@kms_psr2_sf@fbc-psr2-cursor-plane-move-continuous-exceed-sf:
- shard-lnl: NOTRUN -> [SKIP][106] ([Intel XE#1406] / [Intel XE#2893] / [Intel XE#4608])
[106]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_psr2_sf@fbc-psr2-cursor-plane-move-continuous-exceed-sf@pipe-b-edp-1:
- shard-lnl: NOTRUN -> [SKIP][107] ([Intel XE#1406] / [Intel XE#4608]) +1 other test skip
[107]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@kms_psr2_sf@fbc-psr2-cursor-plane-move-continuous-exceed-sf@pipe-b-edp-1.html
* igt@kms_psr2_sf@fbc-psr2-primary-plane-update-sf-dmg-area:
- shard-dg2-set2: NOTRUN -> [SKIP][108] ([Intel XE#1406] / [Intel XE#1489]) +2 other tests skip
[108]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@kms_psr2_sf@pr-overlay-plane-move-continuous-exceed-fully-sf:
- shard-adlp: NOTRUN -> [SKIP][109] ([Intel XE#1406] / [Intel XE#1489]) +10 other tests skip
[109]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@kms_psr2_sf@pr-overlay-plane-move-continuous-exceed-fully-sf.html
* igt@kms_psr2_sf@pr-overlay-plane-move-continuous-sf:
- shard-bmg: NOTRUN -> [SKIP][110] ([Intel XE#1406] / [Intel XE#1489])
[110]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_psr2_sf@pr-overlay-primary-update-sf-dmg-area:
- shard-lnl: NOTRUN -> [SKIP][111] ([Intel XE#1406] / [Intel XE#2893])
[111]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_psr2_su@frontbuffer-xrgb8888:
- shard-adlp: NOTRUN -> [SKIP][112] ([Intel XE#1122] / [Intel XE#1406] / [Intel XE#5580])
[112]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@kms_psr@fbc-pr-cursor-plane-move:
- shard-lnl: NOTRUN -> [SKIP][113] ([Intel XE#1406]) +1 other test skip
[113]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@kms_psr@fbc-pr-sprite-render:
- shard-adlp: NOTRUN -> [SKIP][114] ([Intel XE#1406] / [Intel XE#2850] / [Intel XE#929]) +14 other tests skip
[114]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@kms_psr@pr-dpms:
- shard-dg2-set2: NOTRUN -> [SKIP][115] ([Intel XE#1406] / [Intel XE#2850] / [Intel XE#929]) +1 other test skip
[115]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-432/igt@[email protected]
* igt@kms_psr@pr-primary-blt:
- shard-bmg: NOTRUN -> [SKIP][116] ([Intel XE#1406] / [Intel XE#2234] / [Intel XE#2850])
[116]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_rotation_crc@primary-yf-tiled-reflect-x-0:
- shard-dg2-set2: NOTRUN -> [SKIP][117] ([Intel XE#1127])
[117]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-432/igt@[email protected]
* igt@kms_rotation_crc@primary-yf-tiled-reflect-x-270:
- shard-adlp: NOTRUN -> [SKIP][118] ([Intel XE#3414]) +1 other test skip
[118]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@kms_sequence@get-busy:
- shard-adlp: [PASS][119] -> [DMESG-WARN][120] ([Intel XE#2953] / [Intel XE#4173]) +9 other tests dmesg-warn
[119]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-2/igt@[email protected]
[120]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@kms_setmode@invalid-clone-single-crtc:
- shard-bmg: [PASS][121] -> [SKIP][122] ([Intel XE#1435])
[121]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[122]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_tv_load_detect@load-detect:
- shard-lnl: NOTRUN -> [SKIP][123] ([Intel XE#330])
[123]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
- shard-adlp: NOTRUN -> [SKIP][124] ([Intel XE#330])
[124]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@xe_ccs@suspend-resume:
- shard-adlp: NOTRUN -> [SKIP][125] ([Intel XE#455] / [Intel XE#488] / [Intel XE#5607])
[125]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@xe_compute@ccs-mode-compute-kernel:
- shard-adlp: NOTRUN -> [SKIP][126] ([Intel XE#1447] / [Intel XE#5596])
[126]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_compute_preempt@compute-preempt:
- shard-adlp: NOTRUN -> [SKIP][127] ([Intel XE#455] / [Intel XE#5632])
[127]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@xe_copy_basic@mem-copy-linear-0xfd:
- shard-adlp: NOTRUN -> [SKIP][128] ([Intel XE#1123])
[128]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@xe_copy_basic@mem-set-linear-0x369:
- shard-adlp: NOTRUN -> [SKIP][129] ([Intel XE#1126])
[129]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_eu_stall@blocking-re-enable:
- shard-dg2-set2: NOTRUN -> [SKIP][130] ([Intel XE#5626])
[130]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-432/igt@[email protected]
* igt@xe_eudebug@sysfs-toggle:
- shard-lnl: NOTRUN -> [SKIP][131] ([Intel XE#4837]) +3 other tests skip
[131]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@xe_eudebug_online@single-step:
- shard-adlp: NOTRUN -> [SKIP][132] ([Intel XE#4837] / [Intel XE#5565]) +15 other tests skip
[132]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_evict@evict-large-cm:
- shard-adlp: NOTRUN -> [SKIP][133] ([Intel XE#261] / [Intel XE#5564]) +3 other tests skip
[133]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_evict@evict-mixed-many-threads-small:
- shard-adlp: NOTRUN -> [SKIP][134] ([Intel XE#261]) +5 other tests skip
[134]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
- shard-lnl: NOTRUN -> [SKIP][135] ([Intel XE#688]) +1 other test skip
[135]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@xe_evict@evict-threads-small:
- shard-adlp: NOTRUN -> [SKIP][136] ([Intel XE#261] / [Intel XE#688])
[136]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_evict_ccs@evict-overcommit-standalone-nofree-reopen:
- shard-adlp: NOTRUN -> [SKIP][137] ([Intel XE#688])
[137]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@xe_exec_balancer@many-execqueues-cm-virtual-userptr-invalidate-race:
- shard-bmg: [PASS][138] -> [FAIL][139] ([Intel XE#5625]) +1 other test fail
[138]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@xe_exec_balancer@many-execqueues-cm-virtual-userptr-invalidate-race.html
[139]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@xe_exec_balancer@many-execqueues-cm-virtual-userptr-invalidate-race.html
* igt@xe_exec_basic@multigpu-many-execqueues-many-vm-bindexecqueue-userptr-invalidate:
- shard-adlp: NOTRUN -> [SKIP][140] ([Intel XE#1392] / [Intel XE#5575]) +11 other tests skip
[140]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@xe_exec_basic@multigpu-many-execqueues-many-vm-bindexecqueue-userptr-invalidate.html
* igt@xe_exec_basic@multigpu-no-exec-basic-defer-bind:
- shard-lnl: NOTRUN -> [SKIP][141] ([Intel XE#1392]) +1 other test skip
[141]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@xe_exec_basic@twice-null-rebind:
- shard-bmg: [PASS][142] -> [DMESG-WARN][143] ([Intel XE#3876])
[142]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[143]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@xe_exec_fault_mode@many-bindexecqueue-userptr-imm:
- shard-adlp: NOTRUN -> [SKIP][144] ([Intel XE#288] / [Intel XE#5561]) +30 other tests skip
[144]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@xe_exec_fault_mode@many-execqueues-basic:
- shard-dg2-set2: NOTRUN -> [SKIP][145] ([Intel XE#288])
[145]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@xe_exec_fault_mode@once-bindexecqueue-userptr-invalidate-imm:
- shard-bmg: [PASS][146] -> [FAIL][147] ([Intel XE#6050]) +1 other test fail
[146]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@xe_exec_fault_mode@once-bindexecqueue-userptr-invalidate-imm.html
[147]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@xe_exec_fault_mode@once-bindexecqueue-userptr-invalidate-imm.html
* igt@xe_exec_mix_modes@exec-spinner-interrupted-lr:
- shard-adlp: NOTRUN -> [SKIP][148] ([Intel XE#2360])
[148]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_exec_reset@cm-gt-reset:
- shard-bmg: [PASS][149] -> [FAIL][150] ([Intel XE#6325])
[149]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[150]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@xe_exec_system_allocator@once-mmap-huge-nomemset:
- shard-adlp: NOTRUN -> [SKIP][151] ([Intel XE#4915]) +277 other tests skip
[151]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_exec_system_allocator@process-many-execqueues-malloc-busy-nomemset:
- shard-dg2-set2: NOTRUN -> [SKIP][152] ([Intel XE#4915]) +18 other tests skip
[152]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-432/igt@xe_exec_system_allocator@process-many-execqueues-malloc-busy-nomemset.html
* igt@xe_exec_system_allocator@process-many-malloc-bo-unmap:
- shard-bmg: [PASS][153] -> [FAIL][154] ([Intel XE#4937] / [Intel XE#5625]) +22 other tests fail
[153]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[154]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@xe_exec_system_allocator@threads-many-large-mmap-huge:
- shard-lnl: NOTRUN -> [SKIP][155] ([Intel XE#4943]) +5 other tests skip
[155]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@xe_exec_system_allocator@threads-shared-vm-many-execqueues-mmap-huge-nomemset:
- shard-bmg: NOTRUN -> [SKIP][156] ([Intel XE#4943])
[156]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-1/igt@xe_exec_system_allocator@threads-shared-vm-many-execqueues-mmap-huge-nomemset.html
* igt@xe_exec_threads@threads-bal-shared-vm-basic:
- shard-bmg: [PASS][157] -> [DMESG-FAIL][158] ([Intel XE#3876])
[157]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[158]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@xe_fault_injection@probe-fail-guc-xe_guc_ct_send_recv:
- shard-dg2-set2: NOTRUN -> [ABORT][159] ([Intel XE#5466])
[159]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@xe_fault_injection@probe-fail-guc-xe_guc_ct_send_recv.html
- shard-adlp: NOTRUN -> [ABORT][160] ([Intel XE#5530])
[160]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@xe_fault_injection@probe-fail-guc-xe_guc_ct_send_recv.html
* igt@xe_fault_injection@probe-fail-guc-xe_guc_mmio_send_recv:
- shard-dg2-set2: [PASS][161] -> [DMESG-WARN][162] ([Intel XE#5893])
[161]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-434/igt@xe_fault_injection@probe-fail-guc-xe_guc_mmio_send_recv.html
[162]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@xe_fault_injection@probe-fail-guc-xe_guc_mmio_send_recv.html
* igt@xe_gt_freq@freq_range_exec:
- shard-bmg: [PASS][163] -> [TIMEOUT][164] ([Intel XE#3876]) +1 other test timeout
[163]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@xe_gt_freq@freq_range_exec.html
[164]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@xe_gt_freq@freq_range_exec.html
* igt@xe_live_ktest@xe_bo:
- shard-adlp: NOTRUN -> [SKIP][165] ([Intel XE#2229] / [Intel XE#455]) +1 other test skip
[165]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@xe_live_ktest@xe_bo.html
* igt@xe_live_ktest@xe_bo@xe_ccs_migrate_kunit:
- shard-adlp: NOTRUN -> [SKIP][166] ([Intel XE#2229])
[166]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@xe_live_ktest@xe_bo@xe_ccs_migrate_kunit.html
* igt@xe_mmap@pci-membarrier:
- shard-lnl: NOTRUN -> [SKIP][167] ([Intel XE#5100])
[167]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
- shard-adlp: NOTRUN -> [SKIP][168] ([Intel XE#5100])
[168]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@xe_module_load@force-load:
- shard-adlp: NOTRUN -> [SKIP][169] ([Intel XE#378] / [Intel XE#5612])
[169]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@xe_oa@mmio-triggered-reports-read:
- shard-adlp: NOTRUN -> [SKIP][170] ([Intel XE#6032])
[170]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@xe_oa@syncs-syncobj-cfg:
- shard-adlp: NOTRUN -> [SKIP][171] ([Intel XE#3573]) +6 other tests skip
[171]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@xe_pat@display-vs-wb-transient:
- shard-adlp: NOTRUN -> [SKIP][172] ([Intel XE#1337] / [Intel XE#5572])
[172]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
- shard-dg2-set2: NOTRUN -> [SKIP][173] ([Intel XE#1337])
[173]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@xe_pat@pat-index-xe2:
- shard-adlp: NOTRUN -> [SKIP][174] ([Intel XE#977])
[174]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@xe_pm@d3cold-i2c:
- shard-adlp: NOTRUN -> [SKIP][175] ([Intel XE#5694])
[175]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@xe_pm@d3cold-mmap-vram:
- shard-lnl: NOTRUN -> [SKIP][176] ([Intel XE#2284] / [Intel XE#366]) +1 other test skip
[176]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@xe_pm@s2idle-vm-bind-userptr:
- shard-adlp: [PASS][177] -> [DMESG-WARN][178] ([Intel XE#2953] / [Intel XE#4173] / [Intel XE#4504])
[177]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-2/igt@[email protected]
[178]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@xe_pm@s3-d3cold-basic-exec:
- shard-adlp: NOTRUN -> [SKIP][179] ([Intel XE#2284] / [Intel XE#366]) +1 other test skip
[179]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
* igt@xe_pm@vram-d3cold-threshold:
- shard-adlp: NOTRUN -> [SKIP][180] ([Intel XE#5611] / [Intel XE#579])
[180]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@[email protected]
* igt@xe_pmu@fn-engine-activity-load:
- shard-dg2-set2: NOTRUN -> [SKIP][181] ([Intel XE#4650])
[181]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@xe_pxp@display-pxp-fb:
- shard-bmg: NOTRUN -> [SKIP][182] ([Intel XE#4733])
[182]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-1/igt@[email protected]
* igt@xe_pxp@pxp-stale-bo-exec-post-suspend:
- shard-adlp: NOTRUN -> [SKIP][183] ([Intel XE#4733] / [Intel XE#5594]) +3 other tests skip
[183]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_query@multigpu-query-config:
- shard-lnl: NOTRUN -> [SKIP][184] ([Intel XE#944])
[184]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
* igt@xe_query@multigpu-query-uc-fw-version-huc:
- shard-adlp: NOTRUN -> [SKIP][185] ([Intel XE#944]) +1 other test skip
[185]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-9/igt@[email protected]
* igt@xe_render_copy@render-stress-4-copies:
- shard-adlp: NOTRUN -> [SKIP][186] ([Intel XE#4814] / [Intel XE#5614]) +1 other test skip
[186]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@xe_sriov_scheduling@equal-throughput:
- shard-adlp: NOTRUN -> [DMESG-FAIL][187] ([Intel XE#3868] / [Intel XE#5213]) +1 other test dmesg-fail
[187]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-1/igt@[email protected]
- shard-lnl: NOTRUN -> [SKIP][188] ([Intel XE#4351])
[188]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-3/igt@[email protected]
#### Possible fixes ####
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-rc-ccs:
- shard-dg2-set2: [INCOMPLETE][189] ([Intel XE#1727] / [Intel XE#3113] / [Intel XE#4345] / [Intel XE#6168]) -> [PASS][190]
[189]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-466/igt@[email protected]
[190]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@[email protected]
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-rc-ccs@pipe-d-hdmi-a-6:
- shard-dg2-set2: [INCOMPLETE][191] ([Intel XE#1727] / [Intel XE#3113] / [Intel XE#6168]) -> [PASS][192]
[191]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-466/igt@kms_ccs@[email protected]
[192]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-435/igt@kms_ccs@[email protected]
* igt@kms_cursor_legacy@cursorb-vs-flipa-atomic-transitions-varying-size:
- shard-bmg: [SKIP][193] ([Intel XE#2291]) -> [PASS][194] +8 other tests pass
[193]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@kms_cursor_legacy@cursorb-vs-flipa-atomic-transitions-varying-size.html
[194]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-5/igt@kms_cursor_legacy@cursorb-vs-flipa-atomic-transitions-varying-size.html
* igt@kms_flip@2x-flip-vs-modeset-vs-hang:
- shard-bmg: [SKIP][195] ([Intel XE#2316]) -> [PASS][196] +10 other tests pass
[195]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@[email protected]
[196]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@[email protected]
* igt@kms_flip@flip-vs-expired-vblank-interruptible@b-edp1:
- shard-lnl: [FAIL][197] ([Intel XE#301]) -> [PASS][198]
[197]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-lnl-1/igt@kms_flip@[email protected]
[198]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-lnl-4/igt@kms_flip@[email protected]
* igt@kms_flip@flip-vs-rmfb:
- shard-adlp: [DMESG-WARN][199] ([Intel XE#4543] / [Intel XE#5208]) -> [PASS][200]
[199]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-8/igt@[email protected]
[200]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@[email protected]
* igt@kms_flip@flip-vs-rmfb@b-hdmi-a1:
- shard-adlp: [DMESG-WARN][201] ([Intel XE#4543]) -> [PASS][202] +4 other tests pass
[201]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-8/igt@kms_flip@[email protected]
[202]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@kms_flip@[email protected]
* igt@kms_flip@flip-vs-suspend-interruptible:
- shard-bmg: [INCOMPLETE][203] ([Intel XE#2049] / [Intel XE#2597]) -> [PASS][204] +1 other test pass
[203]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-3/igt@[email protected]
[204]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-4/igt@[email protected]
* igt@kms_hdr@invalid-metadata-sizes:
- shard-bmg: [SKIP][205] ([Intel XE#1503]) -> [PASS][206]
[205]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-6/igt@[email protected]
[206]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-1/igt@[email protected]
* igt@kms_joiner@invalid-modeset-force-big-joiner:
- shard-bmg: [SKIP][207] ([Intel XE#3012]) -> [PASS][208]
[207]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@[email protected]
[208]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@[email protected]
* igt@kms_plane_multiple@2x-tiling-4:
- shard-bmg: [SKIP][209] ([Intel XE#4596]) -> [PASS][210] +1 other test pass
[209]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-6/igt@[email protected]
[210]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-1/igt@[email protected]
* {igt@xe_pmu@fn-engine-activity-sched-if-idle@engine-drm_xe_engine_class_video_enhance1}:
- shard-bmg: [DMESG-WARN][211] ([Intel XE#3876]) -> [PASS][212] +1 other test pass
[211]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-6/igt@xe_pmu@fn-engine-activity-sched-if-idle@engine-drm_xe_engine_class_video_enhance1.html
[212]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-1/igt@xe_pmu@fn-engine-activity-sched-if-idle@engine-drm_xe_engine_class_video_enhance1.html
#### Warnings ####
* igt@kms_ccs@random-ccs-data-4-tiled-dg2-mc-ccs:
- shard-dg2-set2: [INCOMPLETE][213] ([Intel XE#1727] / [Intel XE#3113] / [Intel XE#4345] / [Intel XE#6168]) -> [INCOMPLETE][214] ([Intel XE#1727] / [Intel XE#2705] / [Intel XE#3113] / [Intel XE#4212] / [Intel XE#4345] / [Intel XE#4522])
[213]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-433/igt@[email protected]
[214]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-466/igt@[email protected]
* igt@kms_content_protection@atomic-dpms:
- shard-bmg: [SKIP][215] ([Intel XE#2341]) -> [FAIL][216] ([Intel XE#1178])
[215]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@[email protected]
[216]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@[email protected]
* igt@kms_content_protection@legacy:
- shard-bmg: [FAIL][217] ([Intel XE#1178]) -> [SKIP][218] ([Intel XE#2341]) +1 other test skip
[217]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[218]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_flip_tiling@flip-change-tiling@pipe-d-hdmi-a-1-y-to-y:
- shard-adlp: [DMESG-FAIL][219] ([Intel XE#4543]) -> [FAIL][220] ([Intel XE#1874])
[219]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-8/igt@kms_flip_tiling@[email protected]
[220]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-8/igt@kms_flip_tiling@[email protected]
* igt@kms_frontbuffer_tracking@drrs-2p-scndscrn-pri-indfb-draw-mmap-wc:
- shard-bmg: [SKIP][221] ([Intel XE#2311]) -> [SKIP][222] ([Intel XE#2312]) +18 other tests skip
[221]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-5/igt@kms_frontbuffer_tracking@drrs-2p-scndscrn-pri-indfb-draw-mmap-wc.html
[222]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@kms_frontbuffer_tracking@drrs-2p-scndscrn-pri-indfb-draw-mmap-wc.html
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-shrfb-draw-mmap-wc:
- shard-adlp: [DMESG-FAIL][223] ([Intel XE#4543]) -> [DMESG-FAIL][224] ([Intel XE#2953] / [Intel XE#4173] / [Intel XE#4543])
[223]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-adlp-2/igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-shrfb-draw-mmap-wc.html
[224]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-adlp-6/igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-shrfb-draw-mmap-wc.html
* igt@kms_frontbuffer_tracking@fbc-2p-primscrn-spr-indfb-fullscreen:
- shard-bmg: [SKIP][225] ([Intel XE#2312]) -> [SKIP][226] ([Intel XE#5390]) +10 other tests skip
[225]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@kms_frontbuffer_tracking@fbc-2p-primscrn-spr-indfb-fullscreen.html
[226]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@kms_frontbuffer_tracking@fbc-2p-primscrn-spr-indfb-fullscreen.html
* igt@kms_frontbuffer_tracking@fbc-2p-scndscrn-spr-indfb-onoff:
- shard-bmg: [SKIP][227] ([Intel XE#5390]) -> [SKIP][228] ([Intel XE#2312]) +8 other tests skip
[227]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[228]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_frontbuffer_tracking@fbcdrrs-2p-scndscrn-cur-indfb-draw-mmap-wc:
- shard-bmg: [SKIP][229] ([Intel XE#2312]) -> [SKIP][230] ([Intel XE#2311]) +21 other tests skip
[229]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@kms_frontbuffer_tracking@fbcdrrs-2p-scndscrn-cur-indfb-draw-mmap-wc.html
[230]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-5/igt@kms_frontbuffer_tracking@fbcdrrs-2p-scndscrn-cur-indfb-draw-mmap-wc.html
* igt@kms_frontbuffer_tracking@fbcpsr-2p-scndscrn-cur-indfb-draw-blt:
- shard-bmg: [SKIP][231] ([Intel XE#2312]) -> [SKIP][232] ([Intel XE#2313]) +20 other tests skip
[231]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@kms_frontbuffer_tracking@fbcpsr-2p-scndscrn-cur-indfb-draw-blt.html
[232]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-3/igt@kms_frontbuffer_tracking@fbcpsr-2p-scndscrn-cur-indfb-draw-blt.html
* igt@kms_frontbuffer_tracking@psr-2p-primscrn-indfb-plflip-blt:
- shard-bmg: [SKIP][233] ([Intel XE#2313]) -> [SKIP][234] ([Intel XE#2312]) +19 other tests skip
[233]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[234]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
* igt@kms_hdr@brightness-with-hdr:
- shard-bmg: [SKIP][235] ([Intel XE#3374] / [Intel XE#3544]) -> [SKIP][236] ([Intel XE#3544])
[235]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-4/igt@[email protected]
[236]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-5/igt@[email protected]
* igt@kms_tiled_display@basic-test-pattern-with-chamelium:
- shard-bmg: [SKIP][237] ([Intel XE#2426]) -> [SKIP][238] ([Intel XE#2509])
[237]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-7/igt@[email protected]
[238]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-5/igt@[email protected]
- shard-dg2-set2: [SKIP][239] ([Intel XE#1500]) -> [SKIP][240] ([Intel XE#362])
[239]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-dg2-436/igt@[email protected]
[240]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-dg2-463/igt@[email protected]
* igt@xe_pm@d3hot-i2c:
- shard-bmg: [SKIP][241] ([Intel XE#5742]) -> [TIMEOUT][242] ([Intel XE#3876] / [Intel XE#6162])
[241]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada/shard-bmg-2/igt@[email protected]
[242]: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/shard-bmg-6/igt@[email protected]
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[Intel XE#1122]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1122
[Intel XE#1123]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1123
[Intel XE#1124]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1124
[Intel XE#1125]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1125
[Intel XE#1126]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1126
[Intel XE#1127]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1127
[Intel XE#1135]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1135
[Intel XE#1178]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1178
[Intel XE#1337]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1337
[Intel XE#1340]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1340
[Intel XE#1392]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1392
[Intel XE#1401]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1401
[Intel XE#1406]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1406
[Intel XE#1407]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1407
[Intel XE#1421]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1421
[Intel XE#1424]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1424
[Intel XE#1435]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1435
[Intel XE#1447]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1447
[Intel XE#1468]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1468
[Intel XE#1475]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1475
[Intel XE#1477]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1477
[Intel XE#1489]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1489
[Intel XE#1500]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1500
[Intel XE#1503]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1503
[Intel XE#1727]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1727
[Intel XE#1745]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1745
[Intel XE#1874]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/1874
[Intel XE#2049]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2049
[Intel XE#2191]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2191
[Intel XE#2229]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2229
[Intel XE#2234]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2234
[Intel XE#2284]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2284
[Intel XE#2291]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2291
[Intel XE#2311]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2311
[Intel XE#2312]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2312
[Intel XE#2313]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2313
[Intel XE#2314]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2314
[Intel XE#2316]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2316
[Intel XE#2328]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2328
[Intel XE#2341]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2341
[Intel XE#2360]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2360
[Intel XE#2392]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2392
[Intel XE#2426]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2426
[Intel XE#2509]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2509
[Intel XE#2597]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2597
[Intel XE#261]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/261
[Intel XE#2652]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2652
[Intel XE#2669]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2669
[Intel XE#2705]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2705
[Intel XE#2850]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2850
[Intel XE#288]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/288
[Intel XE#2887]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2887
[Intel XE#2893]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2893
[Intel XE#2894]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2894
[Intel XE#2907]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2907
[Intel XE#2953]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/2953
[Intel XE#3009]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3009
[Intel XE#301]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/301
[Intel XE#3012]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3012
[Intel XE#306]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/306
[Intel XE#307]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/307
[Intel XE#308]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/308
[Intel XE#309]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/309
[Intel XE#310]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/310
[Intel XE#3113]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3113
[Intel XE#316]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/316
[Intel XE#323]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/323
[Intel XE#330]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/330
[Intel XE#3374]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3374
[Intel XE#3414]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3414
[Intel XE#3544]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3544
[Intel XE#3573]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3573
[Intel XE#362]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/362
[Intel XE#366]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/366
[Intel XE#367]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/367
[Intel XE#373]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/373
[Intel XE#378]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/378
[Intel XE#3868]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3868
[Intel XE#3876]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3876
[Intel XE#3884]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/3884
[Intel XE#4173]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4173
[Intel XE#4212]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4212
[Intel XE#4329]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4329
[Intel XE#4331]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4331
[Intel XE#4345]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4345
[Intel XE#4351]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4351
[Intel XE#4354]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4354
[Intel XE#4356]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4356
[Intel XE#4422]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4422
[Intel XE#4504]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4504
[Intel XE#4522]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4522
[Intel XE#4543]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4543
[Intel XE#455]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/455
[Intel XE#4596]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4596
[Intel XE#4608]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4608
[Intel XE#4650]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4650
[Intel XE#4733]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4733
[Intel XE#4814]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4814
[Intel XE#4837]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4837
[Intel XE#488]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/488
[Intel XE#4915]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4915
[Intel XE#4921]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4921
[Intel XE#4937]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4937
[Intel XE#4943]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/4943
[Intel XE#5100]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5100
[Intel XE#5208]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5208
[Intel XE#5213]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5213
[Intel XE#5390]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5390
[Intel XE#5466]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5466
[Intel XE#5503]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5503
[Intel XE#5530]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5530
[Intel XE#5561]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5561
[Intel XE#5564]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5564
[Intel XE#5565]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5565
[Intel XE#5572]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5572
[Intel XE#5574]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5574
[Intel XE#5575]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5575
[Intel XE#5580]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5580
[Intel XE#5594]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5594
[Intel XE#5596]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5596
[Intel XE#5607]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5607
[Intel XE#5611]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5611
[Intel XE#5612]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5612
[Intel XE#5614]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5614
[Intel XE#5625]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5625
[Intel XE#5626]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5626
[Intel XE#5632]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5632
[Intel XE#5694]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5694
[Intel XE#5742]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5742
[Intel XE#5750]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5750
[Intel XE#579]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/579
[Intel XE#5893]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/5893
[Intel XE#6011]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6011
[Intel XE#6014]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6014
[Intel XE#6032]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6032
[Intel XE#6050]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6050
[Intel XE#607]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/607
[Intel XE#610]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/610
[Intel XE#6162]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6162
[Intel XE#6168]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6168
[Intel XE#619]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/619
[Intel XE#6312]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6312
[Intel XE#6320]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6320
[Intel XE#6325]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6325
[Intel XE#6326]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/6326
[Intel XE#651]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/651
[Intel XE#653]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/653
[Intel XE#656]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/656
[Intel XE#688]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/688
[Intel XE#787]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/787
[Intel XE#836]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/836
[Intel XE#870]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/870
[Intel XE#929]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/929
[Intel XE#944]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/944
[Intel XE#977]: https://gitlab.freedesktop.org/drm/xe/kernel/issues/977
Build changes
-------------
* Linux: xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada -> xe-pw-155866v1
IGT_8582: 8582
xe-3911-c917f7d11493984be9f381ca0a7667bd3e587ada: c917f7d11493984be9f381ca0a7667bd3e587ada
xe-pw-155866v1: 155866v1
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/intel-xe/xe-pw-155866v1/index.html