mmc: clean up help texts
PATCH 1/5 mmc: clean up help texts
Remove some repeated words and superfluous newlines in the mmc command help entries.
--- common/cmd_mmc.c | 9 +++++---- 1 files changed, 5 insertions(+), 4 deletions(-)
common/cmd_mmc.c +5 -4
@@ -135,8 +135,9 @@ int do_mmcinfo (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])return 0 ; } -U_BOOT_CMD (mmcinfo,2 ,0 , do_mmcinfo,"mmcinfo <dev num>-- display MMC info\n" , -NULL ); +U_BOOT_CMD (mmcinfo,2 ,0 , do_mmcinfo, +"print MMC information" , +"<dev num>\n" );int do_mmcops (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) {
@@ -218,8 +219,8 @@ int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])U_BOOT_CMD ( mmc,6 ,1 , do_mmcops,"MMC sub system" , -"mmc read <device num> addr blk# cnt\n" +"read <device num> addr blk# cnt\n" "mmc write <device num> addr blk# cnt\n" "mmc rescan <device num>\n" -"mmc list - lists available devices\n" ); +"mmc list - list available devices\n" );#endif
Signature · 1 line
1.6.2.1
PATCH 1/5 mmc: clean up help texts
Andy,
Quoted 4 lines · Rabin Vincent
Remove some repeated words and superfluous newlines in the mmc command help entries.
Signed-off-by Rabin Vincent <[email protected]>
Any comments on this set of patches?
Rabin
PATCH 1/5 mmc: clean up help texts
Quoted 9 lines · Rabin Vincent
Andy,
Quoted 4 lines · Rabin Vincent
Remove some repeated words and superfluous newlines in the mmc command help entries.
Signed-off-by Rabin Vincent <[email protected]>Any comments on this set of patches?
They look good. I've applied them, but I won't push them till I can test them on a board tomorrow. Just want to make sure you didn't break my system. :)
Andy
PATCH 2/5 mmc: check find_mmc_device return value
In reply to Rabin Vincentfind_mmc_device returns NULL if an invalid device number is specified. Check for this to avoid dereferencing NULL pointers.
--- common/cmd_mmc.c | 9 +++++++++ drivers/mmc/mmc.c | 2 +- 2 files changed, 10 insertions(+), 1 deletions(-)
common/cmd_mmc.c +9 -0
@@ -149,6 +149,9 @@ int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])int dev =simple_strtoul (argv[2 ],NULL ,10 );struct mmc *mmc =find_mmc_device (dev); +if (!mmc) +return 1 ; +mmc_init (mmc);return 0 ;
@@ -175,6 +178,9 @@ int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])u32 blk =simple_strtoul (argv[4 ],NULL ,16 );struct mmc *mmc =find_mmc_device (dev); +if (!mmc) +return 1 ; +printf ("\nMMC read: dev # %d, block # %d, count %d ... " , dev, blk, cnt);
@@ -197,6 +203,9 @@ int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])int blk =simple_strtoul (argv[4 ],NULL ,16 ); +if (!mmc) +return 1 ; +printf ("\nMMC write: dev # %d, block # %d, count %d ... " , dev, blk, cnt);
drivers/mmc/mmc.c +1 -1
@@ -846,7 +846,7 @@ block_dev_desc_t *mmc_get_dev(int dev) {struct mmc *mmc =find_mmc_device (dev); -return &mmc->block_dev; +return mmc ? &mmc->block_dev :NULL ; }int mmc_init (struct mmc *mmc)
Signature · 1 line
1.6.2.1
PATCH 3/5 mmc: use lldiv to fix arm eabi build
The generic MMC core uses direct long long divisions, which do not build with ARM EABI toolchains. Use lldiv() instead, which works everywhere.
--- drivers/mmc/mmc.c | 7 ++++--- 1 files changed, 4 insertions(+), 3 deletions(-)
drivers/mmc/mmc.c +4 -3
@@ -31,6 +31,7 @@#include <malloc.h> #include <linux/list.h> #include <mmc.h> +#include <div64.h> static struct list_head mmc_devices;static int cur_dev_num =-1 ;
@@ -155,8 +156,8 @@ int mmc_read(struct mmc *mmc, u64 src, uchar *dst, int size)char *buffer;int i;int blklen = mmc->read_bl_len; -int startblock = src / blklen; -int endblock = (src + size -1 ) / blklen; +int startblock =lldiv (src, mmc->read_bl_len); +int endblock =lldiv (src + size -1 , mmc->read_bl_len);int err =0 ;/* Make a buffer big enough to hold all the blocks we might read */
@@ -789,7 +790,7 @@ int mmc_startup(struct mmc *mmc) mmc->block_dev.lun =0 ; mmc->block_dev.type =0 ; mmc->block_dev.blksz = mmc->read_bl_len; - mmc->block_dev.lba = mmc->capacity/mmc->read_bl_len; + mmc->block_dev.lba =lldiv (mmc->capacity, mmc->read_bl_len);sprintf (mmc->block_dev.vendor,"Man %02x%02x%02x Snr %02x%02x%02x%02x" , mmc->cid[0 ], mmc->cid[1 ], mmc->cid[2 ], mmc->cid[9 ], mmc->cid[10 ], mmc->cid[11 ], mmc->cid[12 ]);
Signature · 1 line
1.6.2.1
PATCH 4/5 mmc: fix response decoding on little endian
The mmc code defines the response as an array of chars. However, it access the response bytes both as (i) an array of four uints (with casts) and (ii) as individual chars. The former case is used more often, including by the driver when it assigns the response.
The char-wise accesses are broken on little endian systems because they assume that the bytes in the uints are in big endian byte order.
This patch fixes this by changing the response to be an array of four uints and replacing the char-wise accesses with equivalent uint-wise accesses.
--- drivers/mmc/mmc.c | 20 ++++++++++---------- include/mmc.h | 6 +++--- 2 files changed, 13 insertions(+), 13 deletions(-)
drivers/mmc/mmc.c +10 -10
@@ -651,7 +651,7 @@ int mmc_startup(struct mmc *mmc) mmc->csd[3 ] = ((uint *)(cmd.response))[3 ];if (mmc->version ==MMC_VERSION_UNKNOWN ) { -int version = (cmd.response[0 ] >>2 ) &0xf ; +int version = (cmd.response[0 ] >>26 ) &0xf ;switch (version) {case 0 :
@@ -676,8 +676,8 @@ int mmc_startup(struct mmc *mmc) }/* divide frequency by 10, since the mults are 10x bigger */ - freq = fbase[(cmd.response[3 ] &0x7 )]; - mult = multipliers[((cmd.response[3 ] >>3 ) &0xf )]; + freq = fbase[(cmd.response[0 ] &0x7 )]; + mult = multipliers[((cmd.response[0 ] >>3 ) &0xf )]; mmc->tran_speed = freq * mult;
@@ -791,13 +791,13 @@ int mmc_startup(struct mmc *mmc) mmc->block_dev.type =0 ; mmc->block_dev.blksz = mmc->read_bl_len; mmc->block_dev.lba =lldiv (mmc->capacity, mmc->read_bl_len); -sprintf (mmc->block_dev.vendor,"Man %02x%02x%02x Snr %02x%02x%02x%02x" , - mmc->cid[0 ], mmc->cid[1 ], mmc->cid[2 ], - mmc->cid[9 ], mmc->cid[10 ], mmc->cid[11 ], mmc->cid[12 ]); -sprintf (mmc->block_dev.product,"%c%c%c%c%c" , mmc->cid[3 ], - mmc->cid[4 ], mmc->cid[5 ], mmc->cid[6 ], mmc->cid[7 ]); -sprintf (mmc->block_dev.revision,"%d.%d" , mmc->cid[8 ] >>4 , - mmc->cid[8 ] &0xf ); +sprintf (mmc->block_dev.vendor,"Man %06x Snr %08x" , mmc->cid[0 ] >>8 , + (mmc->cid[2 ] <<8 ) | (mmc->cid[3 ] >>24 )); +sprintf (mmc->block_dev.product,"%c%c%c%c%c" , mmc->cid[0 ] &0xff , + (mmc->cid[1 ] >>24 ), (mmc->cid[1 ] >>16 ) &0xff , + (mmc->cid[1 ] >>8 ) &0xff , mmc->cid[1 ] &0xff ); +sprintf (mmc->block_dev.revision,"%d.%d" , mmc->cid[2 ] >>28 , + (mmc->cid[2 ] >>24 ) &0xf );init_part (&mmc->block_dev);return 0 ;
include/mmc.h +3 -3
@@ -91,7 +91,7 @@#define MMC_HS_TIMING 0x00000100#define MMC_HS_52MHZ 0x2 -#define OCR_BUSY 0x80 +#define OCR_BUSY 0x80000000#define OCR_HCS 0x40000000#define MMC_VDD_165_195 0x00000080/* VDD voltage 1.65 - 1.95 */
@@ -223,7 +223,7 @@ struct mmc_cmd {ushort cmdidx;uint resp_type;uint cmdarg; -char response[18 ]; +uint response[4 ];uint flags; };
@@ -253,7 +253,7 @@ struct mmc {uint ocr;uint scr[2 ];uint csd[4 ]; -char cid[16 ]; +uint cid[4 ];ushort rca;uint tran_speed;uint read_bl_len;
Signature · 1 line
1.6.2.1
PATCH 5/5 mmc: drop unnecessary casts
Now that response is a uint, we can drop all the casts.
--- drivers/mmc/fsl_esdhc.c | 10 +++++----- drivers/mmc/mmc.c | 20 ++++++++++---------- 2 files changed, 15 insertions(+), 15 deletions(-)
drivers/mmc/fsl_esdhc.c +5 -5
@@ -206,12 +206,12 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data) cmdrsp2 =in_be32 (®s->cmdrsp2); cmdrsp1 =in_be32 (®s->cmdrsp1); cmdrsp0 =in_be32 (®s->cmdrsp0); - ((uint *)(cmd->response))[0 ] = (cmdrsp3 <<8 ) | (cmdrsp2 >>24 ); - ((uint *)(cmd->response))[1 ] = (cmdrsp2 <<8 ) | (cmdrsp1 >>24 ); - ((uint *)(cmd->response))[2 ] = (cmdrsp1 <<8 ) | (cmdrsp0 >>24 ); - ((uint *)(cmd->response))[3 ] = (cmdrsp0 <<8 ); + cmd->response[0 ] = (cmdrsp3 <<8 ) | (cmdrsp2 >>24 ); + cmd->response[1 ] = (cmdrsp2 <<8 ) | (cmdrsp1 >>24 ); + cmd->response[2 ] = (cmdrsp1 <<8 ) | (cmdrsp0 >>24 ); + cmd->response[3 ] = (cmdrsp0 <<8 ); }else - ((uint *)(cmd->response))[0 ] =in_be32 (®s->cmdrsp0); + cmd->response[0 ] =in_be32 (®s->cmdrsp0);/* Wait until all of the blocks are transferred */ if (data) {
drivers/mmc/mmc.c +10 -10
@@ -292,7 +292,7 @@ sd_send_op_cond(struct mmc *mmc)if (mmc->version !=SD_VERSION_2 ) mmc->version =SD_VERSION_1_0 ; - mmc->ocr = ((uint *)(cmd.response))[0 ]; + mmc->ocr = cmd.response[0 ]; mmc->high_capacity = ((mmc->ocr &OCR_HCS ) ==OCR_HCS ); mmc->rca =0 ;
@@ -327,7 +327,7 @@ int mmc_send_op_cond(struct mmc *mmc)return UNUSABLE_ERR ; mmc->version =MMC_VERSION_UNKNOWN ; - mmc->ocr = ((uint *)(cmd.response))[0 ]; + mmc->ocr = cmd.response[0 ]; mmc->high_capacity = ((mmc->ocr &OCR_HCS ) ==OCR_HCS ); mmc->rca =0 ;
@@ -632,7 +632,7 @@ int mmc_startup(struct mmc *mmc)return err;if (IS_SD (mmc)) - mmc->rca = (((uint *)(cmd.response))[0 ] >>16 ) &0xffff ; + mmc->rca = (cmd.response[0 ] >>16 ) &0xffff ;/* Get the Card-Specific Data */ cmd.cmdidx =MMC_CMD_SEND_CSD ;
@@ -645,10 +645,10 @@ int mmc_startup(struct mmc *mmc)if (err)return err; - mmc->csd[0 ] = ((uint *)(cmd.response))[0 ]; - mmc->csd[1 ] = ((uint *)(cmd.response))[1 ]; - mmc->csd[2 ] = ((uint *)(cmd.response))[2 ]; - mmc->csd[3 ] = ((uint *)(cmd.response))[3 ]; + mmc->csd[0 ] = cmd.response[0 ]; + mmc->csd[1 ] = cmd.response[1 ]; + mmc->csd[2 ] = cmd.response[2 ]; + mmc->csd[3 ] = cmd.response[3 ];if (mmc->version ==MMC_VERSION_UNKNOWN ) {int version = (cmd.response[0 ] >>26 ) &0xf ;
@@ -681,12 +681,12 @@ int mmc_startup(struct mmc *mmc) mmc->tran_speed = freq * mult; - mmc->read_bl_len =1 << ((((uint *)(cmd.response))[1 ] >>16 ) &0xf ); + mmc->read_bl_len =1 << ((cmd.response[1 ] >>16 ) &0xf );if (IS_SD (mmc)) mmc->write_bl_len = mmc->read_bl_len;else - mmc->write_bl_len =1 << ((((uint *)(cmd.response))[3 ] >>22 ) &0xf ); + mmc->write_bl_len =1 << ((cmd.response[3 ] >>22 ) &0xf );if (mmc->high_capacity) { csize = (mmc->csd[1 ] &0x3f ) <<16
@@ -819,7 +819,7 @@ int mmc_send_if_cond(struct mmc *mmc)if (err)return err; -if ((((uint *)(cmd.response))[0 ] &0xff ) !=0xaa ) +if ((cmd.response[0 ] &0xff ) !=0xaa )return UNUSABLE_ERR ;else mmc->version =SD_VERSION_2 ;
Signature · 1 line
1.6.2.1