Skip to contentSkip to conversation

Routing for multiple uplinks/providers

LARTC Viaris 4 participants 6 messages Feb 27, 2003 – Aug 1, 2005

lore
Share & tools
lore

Viaris

author
#0 lore raw

Hi, I read the howto of iproute, I have the same case with HOWTO, the difference is that the whole incoming traffic goes through interface 0, the other difference is that I do not want to balance the out going traffic, because I have specific networks to take it throughout another interface.

Mi Case

IF1 --> Input and Output
IF2 --> Only aoutput for three Network

I need Help, How can I execute my case with the case of HowTo?

Thanks In Advanced,

Regards,
4.2. Routing for multiple uplinks/providers
A common configuration is the following, in which there are two providers that connect a local network (or even a single machine) to the big Internet.

                                                                 ________
                                          +------------+        /
                                          |            |       |
                            +-------------+ Provider 1 +-------
        __                  |             |            |     /
    ___/  \_         +------+-------+     +------------+    |
  _/        \__      |     if1      |                      /
 /             \     |              |                      |
| Local network -----+ Linux router |                      |     Internet
 \_           __/    |              |                      |
   \__     __/       |     if2      |                      \
      \___/          +------+-------+     +------------+    |
                            |             |            |     \
                            +-------------+ Provider 2 +-------
                                          |            |       |
                                          +------------+        \________

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Viaris,

Please try again to explain your problem. Snipping the netmap from the LARTC HOWTO, and then telling us that your case is (paraphrased):

the same case as the HOWTO, but not really...

doesn't help us to understand your problem. I'll provide a description of the relevant details required to answer your question.

- Please draw a netmap identifying the location of the linux router and the directly connected networks.
- If there are relevant internal networks, add them.
- Show us the output of "ip route show" and "ip rule show" and "ip route show table $YOUR_TABLE".
- If relevant, show us also "ip address show".
- Describe what is currently working, if anything.
- Describe what is not currently working.
- Ask the question as simply as possible.

There are many people on this list who are willing to help, but we need the above details to do anything more than guess at your problem.

-Martin

: Hi, I read the howto of iproute, I have the same case with HOWTO, the : difference is that the whole incoming traffic goes through interface 0, the : other difference is that I do not want to balance the out going traffic, : because I have specific networks to take it throughout another interface. :
: Mi Case
:
: IF1 --> Input and Output
: IF2 --> Only aoutput for three Network
:
: I need Help, How can I execute my case with the case of HowTo?

Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw

[LARTC] Routing for multiple uplinks/providers problem.

In reply to Viaris

Been running this for quite a while and noticed that have intermittent problems getting out.

Find that if I ping the same site from 2 computers it may work on one and fail on the other. Also was surprised that some time they are going out different interfaces at the same time.

Seems to work all the time from the firewall.

Running 2.6.10 kernel with the multipath routing patches on a debian sarge system.

# ip rule
0:      from all lookup local
60:     from all lookup main
200:    from all lookup 200
201:    from 216.170.136.0/24 lookup isp1
201:    from 24.196.120.28/30 lookup isp2
222:    from all lookup multi
222:    from all lookup multi
32766:  from all lookup main
32767:  from all lookup default

cat /etc/iproute2/rt_tables
#

# reserved values
#
255     local
254     main
253     default
0       unspec
#
# local
#
1       inr.ruhep
201     isp1
202     isp2
222     multi
root@fonroute:~# ip route list table 200
192.168.0.0/16 via 192.168.2.254 dev eth0
root@fonroute:~# ip route list table 201
default via 216.170.136.1 dev eth1  proto static  src 216.170.136.82
prohibit default  proto static  metric 1
root@fonroute:~# ip route list table 202
default via 24.196.120.29 dev eth2  proto static  src 24.196.120.30
prohibit default  proto static  metric 1
root@fonroute:~# ip route list table 222
default  proto static
       nexthop via 216.170.136.1  dev eth1 weight 1
       nexthop via 24.196.120.29  dev eth2 weight 4

using shorewall to setup rules.

iptable -L

Chain PREROUTING (policy ACCEPT)

target     prot opt source               destination
net_dnat   all  --  anywhere             anywhere
net_dnat   all  --  anywhere             anywhere
loc_dnat   all  --  anywhere             anywhere

Chain POSTROUTING (policy ACCEPT)

target     prot opt source               destination
eth1_masq  all  --  anywhere             anywhere
eth2_masq  all  --  anywhere             anywhere

Chain OUTPUT (policy ACCEPT)
target prot opt source destination

Chain eth1_masq (1 references)

target     prot opt source               destination
masq2      all  --  192.168.2.0/24       anywhere

Chain eth2_masq (1 references)

target     prot opt source               destination
masq1      all  --  192.168.2.0/24       anywhere

Chain loc_dnat (1 references)

target     prot opt source               destination
REDIRECT   tcp  --  anywhere             anywhere            tcp dpt:www redir ports 3128

Chain masq1 (1 references)

target     prot opt source               destination
RETURN     all  --  anywhere             192.168.0.0/16
RETURN     all  --  fonroute.advocap.org  anywhere
SNAT       all  --  anywhere             anywhere            to:24.196.120.30

Chain masq2 (1 references)

target     prot opt source               destination
RETURN     all  --  anywhere             192.168.0.0/16
RETURN     all  --  fonroute.advocap.org  anywhere
SNAT       all  --  anywhere             anywhere            to:216.170.136.73

Chain net_dnat (2 references)

target     prot opt source               destination
DNAT       tcp  -- !192.168.0.0/16       anywhere            multiport dports ssh,www to:192.168.2.1
DNAT       tcp  -- !192.168.0.0/16       anywhere            multiport dports smtp,imaps,https to:192.168.2.10
DNAT       tcp  -- !192.168.0.0/16       anywhere            tcp dpt:2525 to:192.168.2.10:25
DNAT       tcp  -- !192.168.0.0/16       anywhere            tcp dpt:8000 to:192.168.2.12:443
DNAT       tcp  -- !192.168.0.0/16       anywhere            tcp dpt:9000 to:192.168.2.12:22
REDIRECT   tcp  --  anywhere             anywhere            tcp dpt:1022 redir ports 22

Have snat on both interfaces
Have rules to keep vpn traffic from getting snated.

Any solution?
Any way to troubleshoot?

John

begin:vcard
fn:John McMonagle
n:McMonagle;John
org:Advocap Inc
adr;dom:;;2929 Harrison St;Oshkosh;WI;54936
email;internet:[email protected]
title:IT Manager
tel;work:920-426-0150
x-mozilla-html:FALSE
url:http://www.advocap.org
version:2.1
end:vcard

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#3 lore raw

Re: [LARTC] Routing for multiple uplinks/providers problem.

In reply to Viaris

Hi John.

Quoted 4 lines · John McMonagle

Find that if I ping the same site from 2 computers it may work on one and fail on the other.
Also was surprised that some time they are going out different interfaces at the same time.

Same symptoms I had.

Quoted 1 line

Have snat on both interfaces

When you SNAT incoming packets, you need to do something different from what is in the HOWTO ([4]) because SNAT is done before the routing desition (check the Kernel Packet Traveling Diagram[5]).

I had the same problem [1]. The solution is to use conntrack and mark packets on arrival, and then route them back using the fwmark[2].

There's no need to tell you I had a hard time with this. There should be a warning about this in the HOWTO (in this page [4]).

The proposed solution I quote in [2] worked for me for the multiple uplink providers + SNAT problem.

It is (Using the same variables that are in the HOWTO [4]):

1) Mark packages on arrival:

iptables -t mangle -A PREROUTING -m conntrack --ctorigdst $IP1 -j
MARK --set-mark=1
iptables -t mangle -A PREROUTING -m conntrack --ctorigdst $IP2 -j
MARK --set-mark=2

And then use the mark to route the outgoing packages correctly.

ip rule add fwmark 1 table T1
ip rule add fwmark 2 table T2

Regards,
Nelson.-

PD : I solved my problem with IPVS and multiple uplink providers (see [3]).

[1] http://mailman.ds9a.nl/pipermail/lartc/2005q2/016171.html
[2] http://mailman.ds9a.nl/pipermail/lartc/2005q2/016441.html
[3] http://arhuaco.blogspot.com/2005/07/ipvs-and-conntrack.html
[4] http://lartc.org/howto/lartc.rpdb.multiple-links.html
[5] http://www.docum.org/docum.org/kptd/

Signature · 9 lines
Homepage : http://geocities.com/arhuaco

The first principle is that you must not fool yourself
and you are the easiest person to fool.
     -- Richard Feynman.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#4 lore raw

Re: [LARTC] Routing for multiple uplinks/providers problem.

In reply to Viaris

I think I said something wrong in my last message.
You DNAT incoming packets and then SNAT them when
they come back if your Linux router has some server behind it. I don't know if this is your case (having servers behind the router).

(I needed to top-post here --- maybe not).

Quoted 51 lines · Nelson Castillo

Hi John.

Quoted 4 lines · John McMonagle

Find that if I ping the same site from 2 computers it may work on one and fail on the other.
Also was surprised that some time they are going out different interfaces at the same time.

Same symptoms I had.

Quoted 1 line

Have snat on both interfaces

When you SNAT incoming packets, you need to do something different from what is in the HOWTO ([4]) because SNAT is done before the routing desition (check the Kernel Packet Traveling Diagram[5]).

I had the same problem [1]. The solution is to use conntrack and mark packets on arrival, and then route them back using the fwmark[2].

There's no need to tell you I had a hard time with this. There should be a warning about this in the HOWTO (in this page [4]).

The proposed solution I quote in [2] worked for me for the multiple uplink providers + SNAT problem.

It is (Using the same variables that are in the HOWTO [4]):

1) Mark packages on arrival:

iptables -t mangle -A PREROUTING -m conntrack --ctorigdst $IP1 -j
MARK --set-mark=1
iptables -t mangle -A PREROUTING -m conntrack --ctorigdst $IP2 -j
MARK --set-mark=2

And then use the mark to route the outgoing packages correctly.

ip rule add fwmark 1 table T1
ip rule add fwmark 2 table T2

Regards,
Nelson.-

PD : I solved my problem with IPVS and multiple uplink providers (see [3]).

[1] http://mailman.ds9a.nl/pipermail/lartc/2005q2/016171.html
[2] http://mailman.ds9a.nl/pipermail/lartc/2005q2/016441.html
[3] http://arhuaco.blogspot.com/2005/07/ipvs-and-conntrack.html
[4] http://lartc.org/howto/lartc.rpdb.multiple-links.html
[5] http://www.docum.org/docum.org/kptd/

Quoted 6 lines

--
Homepage : http://geocities.com/arhuaco

The first principle is that you must not fool yourself and you are the easiest person to fool.
-- Richard Feynman.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#5 lore raw

Re: [LARTC] Routing for multiple uplinks/providers problem.

In reply to Viaris

Nelson

Not been having any problems with incoming DNAT

I'm using a bit different solution.
Noticed that the returning packets wanted to head for the correct interface probably because of conntracking stuff. Problem was they would be routed then the correct interface to whatever one was the default.

What I basically added rules that said if it's from an interfaces ip go out that interface.
This is the setup for one of the isp interfaces:
IP="24.196.120.30"
NET="24.196.120.28"
LENGTH0
ROUTER="24.196.120.29"
BRD="24.196.120.31"
ip link set $IFACE up
ip addr flush dev $IFACE
ip addr add $IP/$LENGTH brd $BRD dev $IFACE
ip rule add prio 201 from $NET/$LENGTH table isp2
ip route add default via $ROUTER dev $IFACE src $IP proto static table isp2
ip route append prohibit default table isp2 metric 1 proto static

# call something to fixup default route
   /etc/network/defroute

Doing some simular tricks to get ipsec vpn works outgoing from the firewall.

IP="192.168.2.254"
NET="192.168.2.0"
LENGTH$
BRD="192.168.2.255"
ip link set $IFACE up
ip addr flush dev $IFACE
ip addr add $IP/$LENGTH brd $BRD dev $IFACE
#next is to make sure local 192.168. goes via eth0 ip rule delete prio 200 table 220
ip route del table 200
ip route add 192.168.0.0/16 via $IP dev $IFACE table 200 ip rule add prio 200 table 200

Quoted 5 lines · Nelson Castillo

I think I said something wrong in my last message.
You DNAT incoming packets and then SNAT them when
they come back if your Linux router has some server behind it. I don't know if this is your case (having servers behind the router).

Quoted 70 lines

(I needed to top-post here --- maybe not).

Quoted 65 lines · Nelson Castillo

Hi John.

Quoted 6 lines · John McMonagle

Find that if I ping the same site from 2 computers it may work on one and fail on the other.
Also was surprised that some time they are going out different interfaces at the same time.

Same symptoms I had.

Quoted 3 lines

Have snat on both interfaces

When you SNAT incoming packets, you need to do something different from what is in the HOWTO ([4]) because SNAT is done before the routing desition (check the Kernel Packet Traveling Diagram[5]).

I had the same problem [1]. The solution is to use conntrack and mark packets on arrival, and then route them back using the fwmark[2].

There's no need to tell you I had a hard time with this. There should be a warning about this in the HOWTO (in this page [4]).

The proposed solution I quote in [2] worked for me for the multiple uplink providers + SNAT problem.

It is (Using the same variables that are in the HOWTO [4]):

1) Mark packages on arrival:

iptables -t mangle -A PREROUTING -m conntrack --ctorigdst $IP1 -j MARK --set-mark=1
iptables -t mangle -A PREROUTING -m conntrack --ctorigdst $IP2 -j MARK --set-mark=2

And then use the mark to route the outgoing packages correctly.

ip rule add fwmark 1 table T1
ip rule add fwmark 2 table T2

Regards,
Nelson.-

PD : I solved my problem with IPVS and multiple uplink providers (see [3]).

[1] http://mailman.ds9a.nl/pipermail/lartc/2005q2/016171.html
[2] http://mailman.ds9a.nl/pipermail/lartc/2005q2/016441.html
[3] http://arhuaco.blogspot.com/2005/07/ipvs-and-conntrack.html
[4] http://lartc.org/howto/lartc.rpdb.multiple-links.html
[5] http://www.docum.org/docum.org/kptd/

--
Homepage : http://geocities.com/arhuaco

The first principle is that you must not fool yourself and you are the easiest person to fool.
-- Richard Feynman.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc