riscv: sophgo: milkv_duo: add support for Milk-V Duo board
Subsystems (2)
v4 cover riscv: sophgo: milkv_duo: add support for Milk-V Duo board
The Milk-V Duo board is built upon Sophgo's CV1800B SoC, featuring two XuanTie C906 CPUs running at 1.0GHz and 700MHz, respectively.
This series introduces fundamental support for the Milk-V Duo board, encompassing UART, CPU, and PLIC support. This ensures that U-Boot can operate in serial console mode.
Changes in v4:
- Sync dts files with Linux kernel
Changes in v3:
- Swap patch 1 and 2 duo to dependency of defconfig and device tree
- Enable EFI loader
- Add brief description of the procedure to run u-boot-dtb.bin
Changes in v2:
- Fold the defconfig patch to first patch
- Remove unnecessary environment settings of consoledev and baudrate in config
Kongyang Liu (3):
riscv: dts: sophgo: add basic device tree for Milk-V Duo board
riscv: sophgo: milkv_duo: initial support added
doc: sophgo: milkv_duo: document Milk-V Duo board
arch/riscv/Kconfig | 4 + arch/riscv/dts/Makefile | 1 + arch/riscv/dts/cv1800b-milkv-duo.dts | 38 ++++++ arch/riscv/dts/cv1800b.dtsi | 18 +++ arch/riscv/dts/cv18xx.dtsi | 192 +++++++++++++++++++++++++++ board/sophgo/milkv_duo/Kconfig | 28 ++++ board/sophgo/milkv_duo/MAINTAINERS | 6 + board/sophgo/milkv_duo/Makefile | 5 + board/sophgo/milkv_duo/board.c | 9 ++ configs/milkv_duo_defconfig | 23 ++++ doc/board/index.rst | 1 + doc/board/sophgo/index.rst | 8 ++ doc/board/sophgo/milkv_duo.rst | 64 +++++++++ include/configs/milkv_duo.h | 12 ++ 14 files changed, 409 insertions(+) create mode 100644 arch/riscv/dts/cv1800b-milkv-duo.dts create mode 100644 arch/riscv/dts/cv1800b.dtsi create mode 100644 arch/riscv/dts/cv18xx.dtsi create mode 100644 board/sophgo/milkv_duo/Kconfig create mode 100644 board/sophgo/milkv_duo/MAINTAINERS create mode 100644 board/sophgo/milkv_duo/Makefile create mode 100644 board/sophgo/milkv_duo/board.c create mode 100644 configs/milkv_duo_defconfig create mode 100644 doc/board/sophgo/index.rst create mode 100644 doc/board/sophgo/milkv_duo.rst create mode 100644 include/configs/milkv_duo.h
Signature · 1 line
2.41.0
PATCH v4 1/3 riscv: dts: sophgo: add basic device tree for Milk-V Duo board
Import device tree from Linux kernel to add basic support for CPU, PLIC, UART and Timer. The name cv1800b in the filename represent the chip used on Milk-V Duo board.
---
Changes in v4:
- Sync dts files with Linux kernel
Changes in v3:
- Swap patch 1 and 2 duo to dependency of defconfig and device tree
arch/riscv/dts/Makefile | 1 + arch/riscv/dts/cv1800b-milkv-duo.dts | 38 ++++++ arch/riscv/dts/cv1800b.dtsi | 18 +++ arch/riscv/dts/cv18xx.dtsi | 192 +++++++++++++++++++++++++++ 4 files changed, 249 insertions(+) create mode 100644 arch/riscv/dts/cv1800b-milkv-duo.dts create mode 100644 arch/riscv/dts/cv1800b.dtsi create mode 100644 arch/riscv/dts/cv18xx.dtsi
arch/riscv/dts/Makefile +1 -0
@@ -2,6 +2,7 @@ dtb-$(CONFIG_TARGET_ANDES_AE350) += ae350_32.dtb ae350_64.dtb dtb-$(CONFIG_TARGET_MICROCHIP_ICICLE) += mpfs-icicle-kit.dtb +dtb-$(CONFIG_TARGET_MILKV_DUO) += cv1800b-milkv-duo.dtb dtb-$(CONFIG_TARGET_QEMU_VIRT) += qemu-virt32.dtb qemu-virt64.dtb dtb-$(CONFIG_TARGET_OPENPITON_RISCV64) += openpiton-riscv64.dtb dtb-$(CONFIG_TARGET_SIFIVE_UNLEASHED) += hifive-unleashed-a00.dtb
arch/riscv/dts/cv1800b-milkv-duo.dts new file +38 -0
@@ -0,0 +1,38 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "cv1800b.dtsi" + +/ { + model = "Milk-V Duo"; + compatible = "milkv,duo", "sophgo,cv1800b"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x3f40000>; + }; +}; + +&osc { + clock-frequency = <25000000>; +}; + +&uart0 { + status = "okay"; +};
arch/riscv/dts/cv1800b.dtsi new file +18 -0
@@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "cv18xx.dtsi" + +/ { + compatible = "sophgo,cv1800b"; +}; + +&plic { + compatible = "sophgo,cv1800b-plic", "thead,c900-plic"; +}; + +&clint { + compatible = "sophgo,cv1800b-clint", "thead,c900-clint"; +};
arch/riscv/dts/cv18xx.dtsi new file +192 -0
192 lines not on this page · raw message
Signature · 1 line
2.41.0
Re: [PATCH v4 1/3] riscv: dts: sophgo: add basic device tree for Milk-V Duo board
Quoted 13 lines · Kongyang Liu
Import device tree from Linux kernel to add basic support for CPU, PLIC, UART and Timer. The name cv1800b in the filename represent the chip used on Milk-V Duo board.
Signed-off-by Kongyang Liu <[email protected]>---
Changes in v4:
- Sync dts files with Linux kernelChanges in v3:
- Swap patch 1 and 2 duo to dependency of defconfig and device tree
Quoted 8 lines
arch/riscv/dts/Makefile | 1 + arch/riscv/dts/cv1800b-milkv-duo.dts | 38 ++++++ arch/riscv/dts/cv1800b.dtsi | 18 +++ arch/riscv/dts/cv18xx.dtsi | 192 +++++++++++++++++++++++++++ 4 files changed, 249 insertions(+) create mode 100644 arch/riscv/dts/cv1800b-milkv-duo.dts create mode 100644 arch/riscv/dts/cv1800b.dtsi create mode 100644 arch/riscv/dts/cv18xx.dtsi
PATCH v4 2/3 riscv: sophgo: milkv_duo: initial support added
In reply to Kongyang LiuAdd support for Sophgo's Milk-V Duo board, only minimal device tree and serial console are enabled, and it can boot via vendor first stage bootloader.
---
(no changes since v3)
Changes in v3:
- Enable EFI loader
Changes in v2:
- Fold the defconfig patch to first patch
- Remove unnecessary environment settings of consoledev and baudrate in config
arch/riscv/Kconfig | 4 ++++ board/sophgo/milkv_duo/Kconfig | 28 ++++++++++++++++++++++++++++ board/sophgo/milkv_duo/MAINTAINERS | 6 ++++++ board/sophgo/milkv_duo/Makefile | 5 +++++ board/sophgo/milkv_duo/board.c | 9 +++++++++ configs/milkv_duo_defconfig | 23 +++++++++++++++++++++++ include/configs/milkv_duo.h | 12 ++++++++++++ 7 files changed, 87 insertions(+) create mode 100644 board/sophgo/milkv_duo/Kconfig create mode 100644 board/sophgo/milkv_duo/MAINTAINERS create mode 100644 board/sophgo/milkv_duo/Makefile create mode 100644 board/sophgo/milkv_duo/board.c create mode 100644 configs/milkv_duo_defconfig create mode 100644 include/configs/milkv_duo.h
arch/riscv/Kconfig +4 -0
@@ -14,6 +14,9 @@ config TARGET_ANDES_AE350 config TARGET_MICROCHIP_ICICLE bool "Support Microchip PolarFire-SoC Icicle Board" +config TARGET_MILKV_DUO + bool "Support Milk-v Duo Board" + config TARGET_OPENPITON_RISCV64 bool "Support RISC-V cores on OpenPiton SoC"
@@ -83,6 +86,7 @@ source "board/openpiton/riscv64/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" source "board/sipeed/maix/Kconfig" +source "board/sophgo/milkv_duo/Kconfig" source "board/starfive/visionfive2/Kconfig" source "board/thead/th1520_lpi4a/Kconfig" source "board/xilinx/mbv/Kconfig"
board/sophgo/milkv_duo/Kconfig new file +28 -0
@@ -0,0 +1,28 @@ +if TARGET_MILKV_DUO + +config SYS_BOARD + default "milkv_duo" + +config SYS_VENDOR + default "sophgo" + +config SYS_CPU + default "generic" + +config SYS_CONFIG_NAME + default "milkv_duo" + +config TEXT_BASE + default 0x80200000 + +config ENV_SIZE + default 0x20000 + +config ENV_SECT_SIZE + default 0x40000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select GENERIC_RISCV + +endif
board/sophgo/milkv_duo/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +Milk-V Duo +M: Kongyang Liu <[email protected]> +S: Maintained +F: board/sophgo/milkv_duo/ +F: configs/milkv_duo_defconfig +F: doc/board/sophgo/milkv_duo.rst
board/sophgo/milkv_duo/Makefile new file +5 -0
@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y := board.o
board/sophgo/milkv_duo/board.c new file +9 -0
@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int board_init (void ) +{ +return 0 ; +}
configs/milkv_duo_defconfig new file +23 -0
@@ -0,0 +1,23 @@ +CONFIG_RISCV=y +CONFIG_SYS_MALLOC_LEN=0x820000 +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x82300000 +CONFIG_DEFAULT_DEVICE_TREE="cv1800b-milkv-duo" +CONFIG_IDENT_STRING="milkv_duo" +CONFIG_SYS_LOAD_ADDR=0x80080000 +CONFIG_TARGET_MILKV_DUO=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_FIT=y +CONFIG_SUPPORT_RAW_INITRD=y +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="milkv_duo# " +CONFIG_SYS_MAXARGS=64 +CONFIG_SYS_CBSIZE=512 +CONFIG_SYS_PBSIZE=544 +CONFIG_SYS_BOOTM_LEN=0x4000000 +CONFIG_ENV_OVERWRITE=y +CONFIG_SYS_NS16550=y +CONFIG_SYS_NS16550_MEM32=y
include/configs/milkv_duo.h new file +12 -0
@@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +* +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CFG_SYS_SDRAM_BASE 0x80000000 + +#endif /* __CONFIG_H */
Signature · 1 line
2.41.0
Re: [PATCH v4 2/3] riscv: sophgo: milkv_duo: initial support added
Quoted 17 lines · Kongyang Liu
Add support for Sophgo's Milk-V Duo board, only minimal device tree and serial console are enabled, and it can boot via vendor first stage bootloader.
Signed-off-by Kongyang Liu <[email protected]>---
(no changes since v3)
Changes in v3:
- Enable EFI loaderChanges in v2:
- Fold the defconfig patch to first patch
- Remove unnecessary environment settings of consoledev and baudrate in config
Quoted 14 lines
arch/riscv/Kconfig | 4 ++++ board/sophgo/milkv_duo/Kconfig | 28 ++++++++++++++++++++++++++++ board/sophgo/milkv_duo/MAINTAINERS | 6 ++++++ board/sophgo/milkv_duo/Makefile | 5 +++++ board/sophgo/milkv_duo/board.c | 9 +++++++++ configs/milkv_duo_defconfig | 23 +++++++++++++++++++++++ include/configs/milkv_duo.h | 12 ++++++++++++ 7 files changed, 87 insertions(+) create mode 100644 board/sophgo/milkv_duo/Kconfig create mode 100644 board/sophgo/milkv_duo/MAINTAINERS create mode 100644 board/sophgo/milkv_duo/Makefile create mode 100644 board/sophgo/milkv_duo/board.c create mode 100644 configs/milkv_duo_defconfig create mode 100644 include/configs/milkv_duo.h
PATCH v4 3/3 doc: sophgo: milkv_duo: document Milk-V Duo board
In reply to Kongyang LiuAdd document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
---
(no changes since v3)
Changes in v3:
- Add brief description of the procedure to run u-boot-dtb.bin
doc/board/index.rst | 1 + doc/board/sophgo/index.rst | 8 +++++ doc/board/sophgo/milkv_duo.rst | 64 ++++++++++++++++++++++++++++++++++ 3 files changed, 73 insertions(+) create mode 100644 doc/board/sophgo/index.rst create mode 100644 doc/board/sophgo/milkv_duo.rst
doc/board/index.rst +1 -0
@@ -46,6 +46,7 @@ Board-specific doc sifive/index sipeed/index socionext/index + sophgo/index st/index starfive/index ste/index
doc/board/sophgo/index.rst new file +8 -0
@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Sophgo +====== +.. toctree:: + :maxdepth: 1 + + milkv_duo
doc/board/sophgo/milkv_duo.rst new file +64 -0
64 lines not on this page · raw message
Signature · 1 line
2.41.0
Re: [PATCH v4 3/3] doc: sophgo: milkv_duo: document Milk-V Duo board
Quoted 77 lines · Kongyang Liu
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by Kongyang Liu <[email protected]>---
(no changes since v3)
Changes in v3:
- Add brief description of the procedure to run u-boot-dtb.bindoc/board/index.rst | 1 + doc/board/sophgo/index.rst | 8 +++++ doc/board/sophgo/milkv_duo.rst | 64 ++++++++++++++++++++++++++++++++++ 3 files changed, 73 insertions(+)create mode 100644
doc/board/sophgo/index.rstcreate mode 100644doc/board/sophgo/milkv_duo.rstdoc/board/index.rst +1
-0@@ -46,6 +46,7 @@ Board-specific doc sifive/index sipeed/index socionext/index + sophgo/index st/index starfive/index ste/indexdoc/board/sophgo/index.rst new file +8
-0@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Sophgo +====== +.. toctree:: + :maxdepth: 1 + + milkv_duodoc/board/sophgo/milkv_duo.rst new file +27
-0@@ -0,0 +1,64 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Milk-V Duo +========== + +CV1800B RISC-V SoC +------------------ +The CV1800B is a high-performance, low-power 1+1 64-bit RISC-V SoC from Sophgo. + +Mainline support +---------------- +The support for following drivers are already enabled: +1. ns16550 UART Driver. + +Building +~~~~~~~~ +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: console + + export CROSS_COMPILE=<riscv64 toolchain prefix> + cd <U-Boot-dir> + make milkv_duo_defconfig + make + +This will generate u-boot-dtb.bin
doc/board/sophgo/milkv_duo.rst line 37
Quoted 10 lines
doc/board/sophgo/milkv_duo.rst new file +10
-0+ +Booting +~~~~~~~ +Currently, we rely on vendor FSBL(First Stage Boot Loader) to initialize the +clock and load the u-boot image, then bootup from it. + +Alternatively, to run u-boot-dtb.bin on top of FSBL, follow these steps: + +1. Use the vendor-provided tool to create a unified fip.bin file containing + FSBL, OpenSBI, and U-Boot.
Hello Kongyang,
thank you for providing a documentation for the board.
Concerning the usage of fip.bin it would be helpful to add more detail:
* From where can the vendor code be downloaded?
* Which are the commands to execute?
Best regards
Heinrich
Quoted 27 lines
doc/board/sophgo/milkv_duo.rst new file +27
-0+ +2. Place the generated fip.bin file into the FAT partition of the SD card. + +3. Insert the SD card into the board and power it on. + +The board will automatically execute the FSBL from the fip.bin file. +Subsequently, it will transition to OpenSBI, and finally, OpenSBI will invoke +U-Boot. + + +Sample boot log from Milk-V Duo board +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +.. code-block:: none + + U-Boot 2024.01-rc5-00010-g51965baa36 (Dec 28 2023 - 13:15:53 +0800)milkv_duo + + DRAM: 63.3 MiB + Core: 10 devices, 8 uclasses, devicetree: separate + Loading Environment from nowhere... OK + In: serial@4140000 + Out: serial@4140000 + Err: serial@4140000 + Net: No ethernet found. + milkv_duo# cpu detail + 0: cpu@0 rv64imafdc + ID = 0, freq = 0 Hz: L1 cache, MMU + milkv_duo#
Re: [PATCH v4 3/3] doc: sophgo: milkv_duo: document Milk-V Duo board
Quoted 92 lines · Heinrich Schuchardt <[email protected]> 于2024年1月28日周日 17:16写道:
Quoted 77 lines · Kongyang Liu
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by Kongyang Liu <[email protected]>---
(no changes since v3)
Changes in v3:
- Add brief description of the procedure to run u-boot-dtb.bindoc/board/index.rst | 1 + doc/board/sophgo/index.rst | 8 +++++ doc/board/sophgo/milkv_duo.rst | 64 ++++++++++++++++++++++++++++++++++ 3 files changed, 73 insertions(+)create mode 100644
doc/board/sophgo/index.rstcreate mode 100644doc/board/sophgo/milkv_duo.rstdoc/board/index.rst +1
-0@@ -46,6 +46,7 @@ Board-specific doc sifive/index sipeed/index socionext/index + sophgo/index st/index starfive/index ste/indexdoc/board/sophgo/index.rst new file +8
-0@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Sophgo +====== +.. toctree:: + :maxdepth: 1 + + milkv_duodoc/board/sophgo/milkv_duo.rst new file +27
-0@@ -0,0 +1,64 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Milk-V Duo +========== + +CV1800B RISC-V SoC +------------------ +The CV1800B is a high-performance, low-power 1+1 64-bit RISC-V SoC from Sophgo. + +Mainline support +---------------- +The support for following drivers are already enabled: +1. ns16550 UART Driver. + +Building +~~~~~~~~ +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: console + + export CROSS_COMPILE=<riscv64 toolchain prefix> + cd <U-Boot-dir> + make milkv_duo_defconfig + make + +This will generate u-boot-dtb.bindoc/board/sophgo/milkv_duo.rst line 37
Quoted 10 lines
doc/board/sophgo/milkv_duo.rst new file +10
-0+ +Booting +~~~~~~~ +Currently, we rely on vendor FSBL(First Stage Boot Loader) to initialize the +clock and load the u-boot image, then bootup from it. + +Alternatively, to run u-boot-dtb.bin on top of FSBL, follow these steps: + +1. Use the vendor-provided tool to create a unified fip.bin file containing + FSBL, OpenSBI, and U-Boot.Hello Kongyang,
Quoted 7 lines
thank you for providing a documentation for the board.
Concerning the usage of fip.bin it would be helpful to add more detail:
* From where can the vendor code be downloaded?
* Which are the commands to execute?
We have leveraged the BuildSDK from the Milk-V Duo project
(https://github.com/milkv-duo/duo-buildroot-sdk) and made slight modifications to ensure compatibility with the mainline OpenSBI and U-Boot. After the repository reaches a stable state, we will publish it on GitHub.
Best regards
Kongyang Liu
Quoted 32 lines
Best regards
Heinrich
Quoted 27 lines
doc/board/sophgo/milkv_duo.rst new file +27
-0+ +2. Place the generated fip.bin file into the FAT partition of the SD card. + +3. Insert the SD card into the board and power it on. + +The board will automatically execute the FSBL from the fip.bin file. +Subsequently, it will transition to OpenSBI, and finally, OpenSBI will invoke +U-Boot. + + +Sample boot log from Milk-V Duo board +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +.. code-block:: none + + U-Boot 2024.01-rc5-00010-g51965baa36 (Dec 28 2023 - 13:15:53 +0800)milkv_duo + + DRAM: 63.3 MiB + Core: 10 devices, 8 uclasses, devicetree: separate + Loading Environment from nowhere... OK + In: serial@4140000 + Out: serial@4140000 + Err: serial@4140000 + Net: No ethernet found. + milkv_duo# cpu detail + 0: cpu@0 rv64imafdc + ID = 0, freq = 0 Hz: L1 cache, MMU + milkv_duo#
Re: [PATCH v4 3/3] doc: sophgo: milkv_duo: document Milk-V Duo board
In reply to Heinrich SchuchardtHi Heinrich S
Quoted 96 lines · Heinrich Schuchardt
Quoted 77 lines · Kongyang Liu
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by Kongyang Liu <[email protected]>---
(no changes since v3)
Changes in v3:
- Add brief description of the procedure to run u-boot-dtb.bindoc/board/index.rst | 1 + doc/board/sophgo/index.rst | 8 +++++ doc/board/sophgo/milkv_duo.rst | 64 ++++++++++++++++++++++++++++++++++ 3 files changed, 73 insertions(+)create mode 100644
doc/board/sophgo/index.rstcreate mode 100644doc/board/sophgo/milkv_duo.rstdoc/board/index.rst +1
-0@@ -46,6 +46,7 @@ Board-specific doc sifive/index sipeed/index socionext/index + sophgo/index st/index starfive/index ste/indexdoc/board/sophgo/index.rst new file +8
-0@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Sophgo +====== +.. toctree:: + :maxdepth: 1 + + milkv_duodoc/board/sophgo/milkv_duo.rst new file +27
-0@@ -0,0 +1,64 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Milk-V Duo +========== + +CV1800B RISC-V SoC +------------------ +The CV1800B is a high-performance, low-power 1+1 64-bit RISC-V SoC from Sophgo. + +Mainline support +---------------- +The support for following drivers are already enabled: +1. ns16550 UART Driver. + +Building +~~~~~~~~ +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: console + + export CROSS_COMPILE=<riscv64 toolchain prefix> + cd <U-Boot-dir> + make milkv_duo_defconfig + make + +This will generate u-boot-dtb.bindoc/board/sophgo/milkv_duo.rst line 37
Quoted 10 lines
doc/board/sophgo/milkv_duo.rst new file +10
-0+ +Booting +~~~~~~~ +Currently, we rely on vendor FSBL(First Stage Boot Loader) to initialize the +clock and load the u-boot image, then bootup from it. + +Alternatively, to run u-boot-dtb.bin on top of FSBL, follow these steps: + +1. Use the vendor-provided tool to create a unified fip.bin file containing + FSBL, OpenSBI, and U-Boot.Hello Kongyang,
thank you for providing a documentation for the board.
Concerning the usage of fip.bin it would be helpful to add more detail:
* From where can the vendor code be downloaded?
..
Quoted 1 line
* Which are the commands to execute?
for fip.bin, which is located inside the first vfat partition of SD card, it will be parsed & loaded & excuted by ROM after power on (haven't looked too deep into this)
also the fip.bin image is a combination of FSBL+DDR param+ATF?/OpenSBI+U-boot please see the link below if you're interested
https://github.com/milkv-duo/duo-buildroot-sdk/blob/develop/fsbl/plat/cv180x/fiptool.py#L201
Quoted 32 lines
Best regards
Heinrich
Quoted 27 lines
doc/board/sophgo/milkv_duo.rst new file +27
-0+ +2. Place the generated fip.bin file into the FAT partition of the SD card. + +3. Insert the SD card into the board and power it on. + +The board will automatically execute the FSBL from the fip.bin file. +Subsequently, it will transition to OpenSBI, and finally, OpenSBI will invoke +U-Boot. + + +Sample boot log from Milk-V Duo board +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +.. code-block:: none + + U-Boot 2024.01-rc5-00010-g51965baa36 (Dec 28 2023 - 13:15:53 +0800)milkv_duo + + DRAM: 63.3 MiB + Core: 10 devices, 8 uclasses, devicetree: separate + Loading Environment from nowhere... OK + In: serial@4140000 + Out: serial@4140000 + Err: serial@4140000 + Net: No ethernet found. + milkv_duo# cpu detail + 0: cpu@0 rv64imafdc + ID = 0, freq = 0 Hz: L1 cache, MMU + milkv_duo#
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [PATCH v4 3/3] doc: sophgo: milkv_duo: document Milk-V Duo board
In reply to Kongyang LiuQuoted 10 lines · Kongyang Liu
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by Kongyang Liu <[email protected]>---
(no changes since v3)
Changes in v3:
- Add brief description of the procedure to run u-boot-dtb.bin
Quoted 6 lines
doc/board/index.rst | 1 + doc/board/sophgo/index.rst | 8 +++++ doc/board/sophgo/milkv_duo.rst | 64 ++++++++++++++++++++++++++++++++++ 3 files changed, 73 insertions(+) create mode 100644 doc/board/sophgo/index.rst create mode 100644 doc/board/sophgo/milkv_duo.rst