SPI TPM and SPI flash can not work at the same time
Sherry Zhang (BJ-RD)
First of all, thank you!!!
Like:tpm2_getcap -c properties-fixedtpm2_getcap -c commands
These commands can not work well.
I do more experiments and find that tpm driver can not work well, but I do not know the reason :
spi port0/1: flash port2: TPM2.0
driver modules: tpm_tis.ko(tpm driiver) spi-zx.ko(spi controller driver) m25p80.ko(flash driver)
(1) When I boot with ubuntu16.04 of the kernel-4.16.2 , I find that the os only modprobe tpm_tis.ko and spi-zx.ko without m25p80.ko. So I can see /dev/tpm0,but /dev/mtd0 and /dev/mtd1.
(2) If I do not modprobe m25p80, then /dev/tpm0 works well.
(3) Then I modprobe m25p80,and I test /dev/mtd1. It seems normal.
Then I rmmod spi_zx and m25p80 driver. It seems normal.
But when I rmmod tpm_tis,it shows:
Tpm tpm0: A TPM error (151) occurred stopping the TPM
(4)boot os
rmmod tpm_tis ----- normal
modprobe m25p80 -----normal
./spi_flash /dev/mtd1 --- normal
rmmod m25p80 -----normal
modprobe tpm_tis ------error
tpm_tis MSFT0101:00: 2.0 TPM (device-id 0x101, rev-id 0) tpm tpm0:A TPM error(151) occurred continue selftest tpm tpm0: TPM self test failed
Best regards,
Sherry Zhang
Quoted 17 lines
I wish I could help you more, but your TPM isn't returning a valid RC.
Since bit 7 is set in
0x97, this indicates that it is a FMT 1 response code.Fmt 1 response codes have the handle encoded in bit positions 8-11 inclusive.
And is 1-based per
https://trustedcomputinggroup.org/wp-content/uploads/TPM-Rev-2.0-Part-
2-Structures-01.38.pdf
Section 6.6.It seems the error bits 0-5 inclusive are
0x17which isTPM2_RC_TAG.Which is "a parameter that should be a structure tag has a value that is not supported by the TPM"
Quoted 65 lines
I'm not sure why this is failing on your TPM, do any other
tpm2_getcapcommands work?Like:
tpm2_getcap-c properties-fixedtpm2_getcap-c commandsBill
Quoted 56 lines
-----Original Message-----
From: tpm2 [mailto:tpm2-bounces(a)lists.01.org] On Behalf Of Sherry Zhang(BJ-
RD)
Sent: Monday, November 5, 2018 8:14 PM
To: tpm2(a)lists.01.org
Subject: [tpm2] SPI TPM and SPI flash can not work at the same timeHi All,
Ubuntu16.04 with the kernel 4.16.2:
I use a spi port2 with a FIFO TPM2.0 and two flash on the spi port 0/1.
First, I unload drivers of spi controller and test the TPM2.0 (built-in tpm_tis.o)
#tpm2_abrmd �tcti=”device:/dev/tpm0” �allow-root &
#tpm2_pcrlist
#tpm2_nvlist
And I can use tpm2-tools to test and it is normal .
Then I load spi controller driver, and test
/dev/mtd0at spi port0 that can work well.But when I run the commad “tpm2_nvlist” , it shows a error.
#tpm2_nvlist
ERROR:
Tss2_Sys_GetCapability(0x97)�tpm: handle(unk): incorrect structure tagERROR: Unable to run
tpm2_nvlistPS:
tpm2-tss 2.1.0
Tpm2-abrmd 2.0.3_rc0
Tpm2-tools 3.0.2
Best regards,
Sherry Zhang
保密声明:
本邮件含有保密或专有信息,仅供指定收件人使用。严禁对本邮件或其内容做任何未经授权的查阅、使用、复制或转发。
CONFIDENTIAL NOTE:
This email contains confidential or legally privileged information and is for the sole use of its intended recipient. Any unauthorized review, use, copying or forwarding of this email or the content of this email is strictly prohibited.