2Steve Randall, FC10, TeVii S420, cx88
Sorry for my delayed answer, but your email address is unavailable due to DNS error.
And I was too busy, sorry.
So, is there any news about this sorry driver?
My card still doesn`t work.
can you have a look under /sys/bus/i2c and tell me if you have a tuner
Quoted 2 lines
device and also a tuner' device (with a strange trailing ')???
I have something like this:
# ls -l /sys/bus/i2c/drivers total 0 drwxr-xr-x 2 root root 0 2009-02-07 20:57 dummy drwxr-xr-x 2 root root 0 2009-02-07 15:57 tuner drwxr-xr-x 2 root root 0 2009-02-07 15:57 tuner'
Not sure if this is what you were looking for.
I'm running this on my old NForce2 test box... what hardware are you using?
Quoted 1 line
Hardware that I use:
01:01.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: Device d420:9022
Flags: bus master, medium devsel, latency 64, IRQ 17 Memory at dd000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data <?>
Capabilities: [4c] Power Management version 2
Kernel driver in use: cx8800
Kernel modules: cx8800
01:01.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: Device d420:9022
Flags: bus master, medium devsel, latency 64, IRQ 17 Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
And full 'lspci -vk' output is attached.
Dmesg output is also attached to this letter.
I`ve also tried different drivers and revisions with my 2.6.27.5-117.fc10.i686, even the latest; still nothing.
Email me, if you need more information.
Thanks for help.
MM
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.27.5-117.fc10.i686 ([email protected]) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #1 SMP Tue Nov 18 12:19:59 EST 2008 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffa0000 (usable)
BIOS-e820: 000000007ffa0000 - 000000007ffae000 (ACPI data)
BIOS-e820: 000000007ffae000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)last_pfn = 0x7ffa0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 38000000 @ 7000-c000
Using x86 segment limits to approximate NX protection
RAMDISK: 37c44000 - 37fefe3b
DMI 2.4 present.
ACPI: RSDP 000FAF00, 0014 (r0 ACPIAM)
ACPI: RSDT 7FFA0000, 0038 (r1 A_M_I_ OEMRSDT 9000704 MSFT 97)
ACPI: FACP 7FFA0200, 0084 (r2 A_M_I_ OEMFACP 9000704 MSFT 97)
ACPI: DSDT 7FFA0440, 6A9A (r1 A0888 A0888000 0 INTL 20051117)
ACPI: FACS 7FFAE000, 0040
ACPI: APIC 7FFA0390, 006C (r1 A_M_I_ OEMAPIC 9000704 MSFT 97)
ACPI: MCFG 7FFA0400, 003C (r1 A_M_I_ OEMMCFG 9000704 MSFT 97)
ACPI: OEMB 7FFAE040, 0080 (r1 A_M_I_ AMI_OEM 9000704 MSFT 97)
ACPI: HPET 7FFA6EE0, 0038 (r1 A_M_I_ OEMHPET 9000704 MSFT 97)
1151MB HIGHMEM available.
896MB LOWMEM available.
mapped low ram: 0 - 38000000
low ram: 00000000 - 38000000
bootmap 00008000 - 0000f000
(9 early reservations) ==> bootmem [0000000000 - 0038000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000400000 - 000097116c] TEXT DATA BSS ==> [0000400000 - 000097116c]
#4 [0037c44000 - 0037fefe3b] RAMDISK ==> [0037c44000 - 0037fefe3b]
#5 [0000972000 - 0000976000] INIT_PG_TABLE ==> [0000972000 - 0000976000]
#6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
found SMP MP-table at [c00ff780] 000ff780
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00038000
HighMem 0x00038000 -> 0x0007ffa0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0007ffa0On node 0 totalpages: 524095free_area_init_node: node 0, pgdat c07f2900, node_mem_map c1000000
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 292512 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 2 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000)
PERCPU: Allocating 41372 bytes of per cpu dataNR_CPUS: 32, nr_cpu_ids: 4, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519999
Kernel command line: ro root=UUID=3a6eb9af-a26f-412d-99f7-ffdd5990fc4a rhgb quiet selinux=0 Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c089e000 soft=c087e000
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 2399.956 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2068728k/2096768k available (2732k kernel code, 26840k reserved, 1420k data, 412k init, 1179264k highmem) virtual kernel memory layout:
fixmap : 0xffc57000 - 0xfffff000 (3744 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0814000 - 0xc087b000 ( 412 kB)
.data : 0xc06ab266 - 0xc080e610 (1420 kB)
.text : 0xc0400000 - 0xc06ab266 (2732 kB)Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.91 BogoMIPS (lpj=2399956) Security Framework initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys devices
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU E4600 @ 2.40GHz stepping 0d
CPU 1 irqstacks, hard=c089f000 soft=c087f000
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4799.66 BogoMIPS (lpj=2399832)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU E4600 @ 2.40GHz stepping 0d
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (9599.57 BogoMIPS).
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=184 bytes
sizeof(task_struct)=3268 bytes
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0net_namespace: 840 bytes
Booting paravirtualized kernel on bare hardware
Time: 15:57:20 Date: 02/07/09
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
PCI: 0000:00:1b.0 reg 10 64bit mmio: [dcff8000, dcffbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
PCI: 0000:00:1d.0 reg 20 io port: [8400, 841f]
PCI: 0000:00:1d.1 reg 20 io port: [8800, 881f]
PCI: 0000:00:1d.2 reg 20 io port: [9000, 901f]
PCI: 0000:00:1d.3 reg 20 io port: [9400, 941f]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [dcfff800, dcfffbff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [b000, b007]
PCI: 0000:00:1f.1 reg 14 io port: [a800, a803]
PCI: 0000:00:1f.1 reg 18 io port: [a400, a407]
PCI: 0000:00:1f.1 reg 1c io port: [a000, a003]
PCI: 0000:00:1f.1 reg 20 io port: [9800, 980f]
PCI: 0000:00:1f.2 reg 10 io port: [c800, c807]
PCI: 0000:00:1f.2 reg 14 io port: [c400, c403]
PCI: 0000:00:1f.2 reg 18 io port: [c000, c007]
PCI: 0000:00:1f.2 reg 1c io port: [b800, b803]
PCI: 0000:00:1f.2 reg 20 io port: [b400, b40f]
PCI: 0000:00:1f.2 reg 24 32bit mmio: [dcfffc00, dcffffff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
PCI: 0000:00:1f.3 reg 20 io port: [400, 41f]
PCI: 0000:02:00.0 reg 10 64bit mmio: [e0000000, efffffff]
PCI: 0000:02:00.0 reg 18 64bit mmio: [dffe0000, dffeffff]
PCI: 0000:02:00.0 reg 20 io port: [e000, e0ff]
PCI: 0000:02:00.0 reg 30 32bit mmio: [dffc0000, dffdffff]
pci 0000:02:00.0: supports D1
pci 0000:02:00.0: supports D2
PCI: 0000:02:00.1 reg 10 64bit mmio: [dfff0000, dfffffff]
pci 0000:02:00.1: supports D1
pci 0000:02:00.1: supports D2
Pre-1.1 PCIe device detected, disable ASPM for 0000:00:01.0. It can be enabled forcedly with 'pcie_aspm=force'
PCI: bridge 0000:00:01.0 io port: [e000, efff]
PCI: bridge 0000:00:01.0 32bit mmio: [dff00000, dfffffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [e0000000, efffffff]
PCI: 0000:01:01.0 reg 10 32bit mmio: [dd000000, ddffffff]
PCI: 0000:01:01.2 reg 10 32bit mmio: [de000000, deffffff]
PCI: 0000:01:04.0 reg 10 io port: [d800, d8ff]
PCI: 0000:01:04.0 reg 14 32bit mmio: [dfeffc00, dfeffcff]
PCI: 0000:01:04.0 reg 30 32bit mmio: [dfee0000, dfeeffff]
pci 0000:01:04.0: supports D1
pci 0000:01:04.0: supports D2
pci 0000:01:04.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:01:04.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 io port: [d000, dfff]
PCI: bridge 0000:00:1e.0 32bit mmio: [dd000000, dfefffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - CB, should be C3 [20080609] Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 18 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz tracer: 772 pages allocated for 65536 entries of 48 bytes
actual entries 65620
ACPI: RTC can wake from S4
system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved system 00:07: ioport range 0x290-0x297 has been reserved system 00:08: ioport range 0x4d0-0x4d1 has been reserved system 00:08: ioport range 0x800-0x87f has been reserved system 00:08: ioport range 0x480-0x4bf has been reserved system 00:08: ioport range 0x900-0x91f has been reserved system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved system 00:09: ioport range 0x3f6-0x3f6 has been reserved system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:0f: iomem range 0xffc00000-0xffefffff has been reserved system 00:10: iomem range 0xf0000000-0xf3ffffff has been reserved system 00:11: iomem range 0x0-0x9ffff could not be reserved system 00:11: iomem range 0xc0000-0xdffff could not be reserved system 00:11: iomem range 0xe0000-0xfffff could not be reserved system 00:11: iomem range 0x100000-0x7fffffff could not be reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:02
pci 0000:00:01.0: IO window: 0xe000-0xefff pci 0000:00:01.0: MEM window: 0xdff00000-0xdfffffff pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000efffffff pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1e.0: IO window: 0xd000-0xdfff pci 0000:00:1e.0: MEM window: 0xdd000000-0xdfefffff pci 0000:00:1e.0: PREFETCH window: 0x00000088000000-0x000000880fffff
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 02 index 0 io port: [e000, efff]
bus: 02 index 1 mmio: [dff00000, dfffffff]
bus: 02 index 2 mmio: [e0000000, efffffff]
bus: 02 index 3 mmio: [0, 0]
bus: 01 index 0 io port: [d000, dfff]
bus: 01 index 1 mmio: [dd000000, dfefffff]
bus: 01 index 2 mmio: [88000000, 880fffff]
bus: 01 index 3 io port: [0, ffff]
bus: 01 index 4 mmio: [0, ffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 3759k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1234022239.398:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1746
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:02:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capabilitypci_express 0000:00:01.0:pcie00: allocate port servicepci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT 7FFAE0C0, 0256 (r1 AMI CPU1PM 1 INTL 20060113)
processor ACPI0007:00: registered as cooling_device0
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: SSDT 7FFAE320, 0143 (r1 AMI CPU2PM 1 INTL 20060113)
processor ACPI0007:01: registered as cooling_device1
ACPI: Processor [CPU2] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device foundhpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methodsata_piix 0000:00:1f.1: version 2.12ata_piix 0000:00:1f.1: PCI INT A -> GSI 22 (level, low) -> IRQ 22ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0xb000 ctl 0xa800 bmdma 0x9800 irq 22
ata2: PATA max UDMA/100 cmd 0xa400 ctl 0xa000 bmdma 0x9808 irq 22
ata1.01: ATAPI: _NEC DVD_RW ND-3551A, 2.01, max UDMA/33
ata1.01: configured for UDMA/33
scsi 0:0:1:0: CD-ROM _NEC DVD_RW ND-3551A 2.01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:1:0: Attached scsi CD-ROM sr0
sr 0:0:1:0: Attached scsi generic sg0 type 5ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]ata_piix 0000:00:1f.2: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xc800 ctl 0xc400 bmdma 0xb400 irq 23
ata4: SATA max UDMA/133 cmd 0xc000 ctl 0xb800 bmdma 0xb408 irq 23
ata3.00: ATA-8: WDC WD800AAJS-00B4A0, 01.03A01, max UDMA/133
ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD800AAJS-00 01.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg1 type 0ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20ehci_hcd 0000:00:1d.7: setting latency timer to 64ehci_hcd 0000:00:1d.7: EHCI Host Controllerehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1ehci_hcd 0000:00:1d.7: debug port 1ehci_hcd 0000:00:1d.7: cache line size of 32 is not supportedehci_hcd 0000:00:1d.7: irq 20, io mem 0xdcfff800ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.5-117.fc10.i686 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20uhci_hcd 0000:00:1d.0: setting latency timer to 64uhci_hcd 0000:00:1d.0: UHCI Host Controlleruhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2uhci_hcd 0000:00:1d.0: irq 20, io base 0x00008400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.5-117.fc10.i686 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17uhci_hcd 0000:00:1d.1: setting latency timer to 64uhci_hcd 0000:00:1d.1: UHCI Host Controlleruhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27.5-117.fc10.i686 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18uhci_hcd 0000:00:1d.2: setting latency timer to 64uhci_hcd 0000:00:1d.2: UHCI Host Controlleruhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4uhci_hcd 0000:00:1d.2: irq 18, io base 0x00009000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27.5-117.fc10.i686 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19uhci_hcd 0000:00:1d.3: setting latency timer to 64uhci_hcd 0000:00:1d.3: UHCI Host Controlleruhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5uhci_hcd 0000:00:1d.3: irq 19, io base 0x00009400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27.5-117.fc10.i686 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected]
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core drivernf_conntrack version 0.5.0 (16384 buckets, 65536 max)CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it.ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Magic number: 13:532:992
Freeing unused kernel memory: 412k freed
Write protecting the kernel text: 2736k
Write protecting the kernel read-only data: 1172k
[drm] Initialized drm 1.1.0 20060810
pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:02:00.0: setting latency timer to 64
ATOM BIOS: RV515LE 102-A67608-10 A12 Infineon DDR2 BIOS 450e/250m Channel AB [drm] Detected VRAM RAM=524288K, accessible=262144K, BAR=262144K
psmouse serio1: ID: 10 00 64<6>i2c-adapter i2c-1: unable to read EDID block.
pci 0000:02:00.0: DVI-I-1: no EDID data
allocated f5fbc000 1280x1024 fb: 0x00048000, bo f5b0fb80
fbcon: radeondrmfb (fb0) is primary device
Console: switching to colour frame buffer device 160x64
executing set pll
executing set crtc timing
[drm] DAC-6: set mode 1280x1024 1c
fb0: radeondrmfb frame buffer device
registered panic notifier
[drm] Loading R500 Microcode
[drm] Num pipes: 1
[drm] writeback test succeeded in 1 usecs
[drm] Initialized radeon 1.29.0 20080528 on minor 0
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4 kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 127 started
input: PC Speaker as /devices/platform/pcspkr/input/input5
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077intel_rng: FWH not detectedi801_smbus 0000:00:1f.3: PCI INT B -> GSI 23 (level, low) -> IRQ 23iTCO_vendor_support: vendor-support=0iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
8139too Fast Ethernet driver 0.9.28
8139too 0000:01:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
eth0: RealTek RTL8139 at 0xf9168c00, 00:80:48:41:1a:d9, IRQ 21
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
HDA Intel 0000:00:1b.0: setting latency timer to 64
Linux video capture interface: v2.00
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
cx8800 0000:01:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73,autodetected], frontend(s): 1 cx88[0]: TV tuner type -1, Radio tuner type -1
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
tuner' 3-0062: chip found @ 0xc4 (cx88[0])
tuner' 3-0068: chip found @ 0xd0 (cx88[0])
cx88[0]/0: found at 0000:01:01.0, rev: 5, irq: 17, latency: 64, mmio: 0xdd000000 cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
tuner' 3-0062: tuner type not set
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:01:01.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17 cx88[0]/2: found at 0000:01:01.2, rev: 5, irq: 17, latency: 64, mmio: 0xde000000 cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
cx88[0]/2: cx2388x based DVB/ATSC cardcx8802_alloc_frontends() allocating 1 frontend(s)
device-mapper: multipath: version 1.0.5 loaded
cx88[0]/2: dvb_register failed (err = -22)
cx88[0]/2: cx8802 probe failed, err = -22
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 4128760k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:4128760k IA-32 Microcode Update Driver: v1.14a <[email protected]>
firmware: requesting intel-ucode/06-0f-0d
firmware: requesting intel-ucode/06-0f-0d
microcode: CPU0 updated from revision 0xa1 to 0xa3, date = 08132007
microcode: CPU1 updated from revision 0xa1 to 0xa3, date = 08132007
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present
mtrr: base(0xe1470000) is not aligned on a size(0x785000) boundary
fuse init (API version 7.9)
lspci[2613]: segfault at 0 ip 0061f5a5 sp bfe15a20 error 4 in libc-2.9.so[5c0000+16e000] lspci[2614]: segfault at 0 ip 0061f5a5 sp bf959570 error 4 in libc-2.9.so[5c0000+16e000] PPP generic driver version 2.4.2
PPP Deflate Compression module registered
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
Subsystem: ASUSTeK Computer Inc. Device 817a
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>
00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: dff00000-dfffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8290
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at dcff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: bus master, medium devsel, latency 0, IRQ 20
I/O ports at 8400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: bus master, medium devsel, latency 0, IRQ 17
I/O ports at 8800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at 9000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at 9400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: bus master, medium devsel, latency 0, IRQ 20
Memory at dcfff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dd000000-dfefffff Prefetchable memory behind bridge: 0000000088000000-00000000880fffff Capabilities: <access denied>
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Device 8179 Flags: bus master, medium devsel, latency 0, IRQ 22 I/O ports at b000 [size=8] I/O ports at a800 [size=4] I/O ports at a400 [size=8] I/O ports at a000 [size=4] I/O ports at 9800 [size=16] Kernel driver in use: ata_piix
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Device 8179 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 23 I/O ports at c800 [size=8] I/O ports at c400 [size=4] I/O ports at c000 [size=8] I/O ports at b800 [size=4] I/O ports at b400 [size=16] Memory at dcfffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Device 8179
Flags: medium devsel, IRQ 23
I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:01.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: Device d420:9022
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at dd000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: <access denied>
Kernel driver in use: cx8800
Kernel modules: cx8800
01:01.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
Subsystem: Device d420:9022
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: <access denied>
Kernel driver in use: cx88-mpeg driver manager
Kernel modules: cx8802
01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 Flags: bus master, medium devsel, latency 64, IRQ 21 I/O ports at d800 [size=256] Memory at dfeffc00 (32-bit, non-prefetchable) [size=256] Expansion ROM at 88000000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: 8139too Kernel modules: 8139cp, 8139too
02:00.0 VGA compatible controller: ATI Technologies Inc RV515 [Radeon X1300] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device 0840
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Memory at dffe0000 (64-bit, non-prefetchable) [size=64K]
I/O ports at e000 [size=256]
Expansion ROM at dffc0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeon
02:00.1 Display controller: ATI Technologies Inc RV515 [Radeon X1300] (Secondary)
Subsystem: PC Partner Limited Device 0841
Flags: bus master, fast devsel, latency 0
Memory at dfff0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list