Skip to contentSkip to conversation

ARP routing issue

DISCUSSION Zhenyu Wu 1 participant 1 message Jan 7, 2005

lore
Share & tools
lore

Zhenyu Wu

author
#0 lore raw

I met a question about ARP. If i send packet to another host using Raw socket at one host and i set protocol type into TCP, then at another host i receive the packet, but when i read the field skb->protocol, it is ARP. But when i changed a host to send the packet, it does well.

There are something wrong on my network card or the Kernel?

Quoted 92 lines

Hello,

Have a look at /proc/sys/net/conf/XXX/arp_filter :

arp_filter - BOOLEAN
1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not the kernel would route a packet from the ARP'd IP out that interface (therefore you must use source based routing for this to work). In other words it allows control of which cards (usually 1) will respond to an arp request.

0 - (default) The kernel can respond to arp requests with addresses from other interfaces. This may seem wrong but it usually makes sense, because it increases the chance of successful communication. IP addresses are owned by the complete host on Linux, not by particular interfaces. Only for more complex setups like load- balancing, does this behaviour cause problems.

Regards,
Paul

Paul Rolland, rol(at)as2917.net
ex-AS2917 Network administrator and Peering Coordinator

--

Please no HTML, I'm not a browser - Pas d'HTML, je ne suis pas un navigateur

"Some people dream of success... while others wake up and work hard at it"

Quoted 33 lines

-----Message d'origine-----
De : [email protected] [mailto:[email protected]] De la part de Jan De Luyck Envoy?: jeudi 6 janvier 2005 17:12
?: Steve Iribarne
Cc : [email protected]; [email protected] Objet : Re: ARP routing issue

Quoted 11 lines · Steve Iribarne

Hi Jan,

-> default gateway is set to 10.0.22.1, on eth0.
->
-> Problem is, if I try to ping from another network -> (10.216.0.xx) to 10.0.24.xx, i see the following ARP request:
->
-> arp who-has 10.0.22.1 tell 10.0.24.xx
->

Quoted 4 lines

You see that coming out the eth0 interface??

If that is the case it is most definately wrong. Assuming that your masks are setup properly. But I haven't worked on the 2.4

kernel for a

Quoted 1 line

long time so I'm not so sure if what you are seeing is a

bug that has

Quoted 1 line

been fixed.

The network information is:
eth0 10.0.22.xxx mask 255.255.255.0
eth1 10.0.24.xxx mask 255.255.255.0

Quoted 18 lines

routing:
10.0.22.0 0.0.0.0 255.255.255.0 eth0
10.0.24.0 0.0.0.0 255.255.255.0 eth1
0.0.0.0 10.0.22.1 0.0.0.0 eth0

Jan

Signature · 9 lines
If a man slept by day, he had little time to work.  That was a
satisfying notion to Escargot.
  -- "The Stone Giant", James P. Blaylock
-
To unsubscribe from this list: send the line "unsubscribe 
linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/