Skip to contentSkip to conversation

More gateways in the same subnet

DISCUSSION Kevin de Kok 3 participants 3 messages Mar 27, 2005 – Mar 28, 2005

lore
Share & tools
lore
#0 lore raw

Hi,

I have a linux router in my lan with two nic's to two isp's and i also have two nic's for the lan. I have on eth0 the ip from ISP1 on eth2 the ip from ISP2 on eth1 i have 192.168.1.1 and on eth3 i have 192.168.1.2. What i'am trying to is when i give 192.168.1.1 as gateway on a client in my lan then the traffic go's over ISP1 and when i give as gateway 192.168.1.2 that the traffic go's over ISP2. How can i manage this?

#1 lore raw

echo 100 isp1 >> /etc/iproute2/rt_tables
echo 101 isp2 >> /etc/iproute2/rt_tables

ip ro add 192.168.1.0/24 dev eth1 table isp1
ip ro add 192.168.1.0/24 dev eth3 table isp2
ip ro add <isp1_subnet_link> dev eth0 table isp1
ip ro add <isp2_subnet_link> dev eth2 table isp2

if ISP1 gave you the 1.2.3.4ip, then <isp1_subnet_link> will be 1.2.3.0/24 , or whatever the netmask may be. Now do:

ip ro add default via <isp1_gw> table isp1
ip ro add default via <isp2_gw> table isp2

also

ip ro add default via <whatever_isp_gw_you_want> if you happen not to have a default gateway

and last;

ip rule add from 192.168.1.0/24 iif dev eth1 table isp1 ip rule add from 192.168.1.0/24 iif dev eth3 table isp2

Hopefully it will work :)
One problem will be if both ethernet cards will reply to some ap query, so even a client choose 192.168.1.1 as a gateway, the traffic may come on eth3.

Quoted 10 lines · Kevin de Kok

Hi,

I have a linux router in my lan with two nic's to two isp's and i also have two nic's for the lan. I have on eth0 the ip from ISP1 on eth2 the ip from ISP2 on eth1 i have 192.168.1.1 and on eth3 i have 192.168.1.2. What i'am trying to is when i give 192.168.1.1 as gateway on a client in my lan then the traffic go's over ISP1 and when i give as gateway 192.168.1.2 that the traffic go's over ISP2. How can i manage this?

Signature · 1 line
Bla bla
#2 lore raw

I would be tempted to add ISP2's gateway as a 2nd default route with a higher metric to ISP1's table, and vice versa. Thus having some sort of redundancy if either of the connections goes down. I think the line would be something like:

ip ro add default via <isp2_gw> table isp1 metric 2 ip ro add default via <isp1_gw> table isp2 metric 2

I have not done much work with routing via the new ip route command so my syntax could be a bit off so double check me. If any one does see any errors please let me know.

Something else you might consider playing with would be Equal Cost Multi Path (ECMP) routing. I have had limited success with ECMP routing in the past. Rather I had success with it but it sort of failed under high load in an extremely unique situation where I was (attempting to) pseudo load balancing across 8 cable modems each of which having a globally routable IP in the same subnet. All testing that I did seemed to work just fine until the system was under load and then it seemed as if some rare packets would go out a different interface than they started out. Thus the TCP connection was broken as the packets were then coming from a different IP than they started at. However I think that ECMP is a VERY good idea and I'm planing on doing some more testing with it. I also have plans of documenting my situation to this mail list at a later point in time for it's opinion. In short g ive ECMP a try for you self and see what sort of mileage you get. I was happy with it, bu
t I think I was breaking it in what I was doing, not that it broke it's self. To do ECMP routing you would have rules like the following:

ip ro add default via <isp1_gw> dev eth0 weight 1 nexthop via <isp2_gw> dev eth2 weight 1 table isp1 ip ro add default via <isp2_gw> dev eth2 weight 1 nexthop via <isp1_gw> dev eth0 weight 1 table isp2

Grant. . . .

Quoted 28 lines · George Alexandru Dragoi

echo 100 isp1 >> /etc/iproute2/rt_tables
echo 101 isp2 >> /etc/iproute2/rt_tables

ip ro add 192.168.1.0/24 dev eth1 table isp1
ip ro add 192.168.1.0/24 dev eth3 table isp2
ip ro add <isp1_subnet_link> dev eth0 table isp1
ip ro add <isp2_subnet_link> dev eth2 table isp2

if ISP1 gave you the 1.2.3.4ip, then <isp1_subnet_link> will be 1.2.3.0/24 , or whatever the netmask may be. Now do:

ip ro add default via <isp1_gw> table isp1
ip ro add default via <isp2_gw> table isp2

also

ip ro add default via <whatever_isp_gw_you_want> if you happen not to have a default gateway

and last;

ip rule add from 192.168.1.0/24 iif dev eth1 table isp1 ip rule add from 192.168.1.0/24 iif dev eth3 table isp2

Hopefully it will work :)
One problem will be if both ethernet cards will reply to some ap query, so even a client choose 192.168.1.1 as a gateway, the traffic may come on eth3.