Compilation problem for TI3430 board.

U-Boot Jerry Van Baren 3 participants 4 messages Oct 17, 2008 – Oct 18, 2008 1 message not in the archive

lore

Share & tools

lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Jerry Van Baren

author

2008-10-17 18:06 UTC #1 lore raw

Hi Radha,

Please don't top post.

Quoted 2 lines · Radha Krishna

Hi GVB,
You are right. Could you tell me the solution.

Don't use DOS (aka Windows).

Since you already have a problem there, you can use "dos2unix" or equivalent. If you feel you must use Windows, many Windows editors (e.g. UltraEdit) allow you to control/convert line endings.

Quoted 2 lines

Best Regards,
Kris.

[snip]

Quoted 13 lines

Quoted 13 lines
Quoted 1 line
$ make CROSS_COMPILE=arm-none-linux-gnueabi-
omap3430sdp_config
Quoted 1 line
./mkconfig: line 2: $'\r': command not
found
Quoted 1 line
make: *** [omap3430sdp_config] Error 127
Is that telling you that you have DOS line endings (<CR>+<LF> i.e. \r\n)
as opposed to unix line endings (\n only)?
Quoted 4 lines
$ make CROSS_COMPILE=arm-none-linux-gnueabi-
System not configured - see README
make: *** [all] Error 1

Quoted 7 lines

Quoted 7 lines
Quoted 5 lines
Could somebody tell me steps to compile U-Boot for
TI3430.
Best Regards,
Krishna.
My best guess,
gvb

HTH,
gvb

Radha Krishna

2008-10-18 00:35 UTC #2 lore raw

Hi GVB,

Thanks for your earlier help.

As you suggested I have DOS to UNIX conversion. It worked. I have another proble now.

make: arm-none-linux-gnueabi-gcc: Command not found

$ make CROSS_COMPILE=arm-none-linux-gnueabi- omap3430sdp_config
Configuring for omap3430sdp board...

[SNIP]

$ make CROSS_COMPILE=arm-none-linux-gnueabi-
make: arm-none-linux-gnueabi-gcc: Command not found
make[1]: arm-none-linux-gnueabi-gcc: Command not found
make[1]: Entering directory `/cygdrive/c/u-boot/tools'
make[1]: Entering directory `/cygdrive/c/u-boot/tools'
ln -s ../common/environment.c environment.c
ln -s ../lib_generic/crc32.c crc32.c

Could please somebody tell me the solution for this.

Best Regards,
Krishna.

Quoted 43 lines

From: Jerry Van Baren <[email protected]>
Subject: Re: [U-Boot-Users] Compilation problem for TI3430 board.
To: hi_krishna01 at yahoo.com, "U-Boot user list" <[email protected]>
Date: Friday, October 17, 2008, 11:06 AM
Hi Radha,
Please don't top post.
Quoted 2 lines · Radha Krishna
Hi GVB,
You are right. Could you tell me the solution.
Don't use DOS (aka Windows).
Since you already have a problem there, you can use "dos2unix" or
equivalent. If you feel you must use Windows, many Windows editors
(e.g. UltraEdit) allow you to control/convert line endings.
Quoted 2 lines
Best Regards,
Kris.
[snip]
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
$ make CROSS_COMPILE=arm-none-linux-gnueabi-
omap3430sdp_config
Quoted 1 line
./mkconfig: line 2: $'\r': command
not
Quoted 11 lines
Quoted 11 lines
found
Quoted 1 line
make: *** [omap3430sdp_config] Error 127
Is that telling you that you have DOS line endings (<CR>+<LF> i.e. \r\n)
as opposed to unix line endings (\n only)?
Quoted 5 lines
$ make CROSS_COMPILE=arm-none-linux-gnueabi-
System not configured - see README
make: *** [all] Error 1
Could somebody tell me steps to compile
U-Boot for
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
TI3430.

Quoted 7 lines

Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
Best Regards,
Krishna.
My best guess,
gvb
HTH,
gvb

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

Wolfgang Denk

2008-10-18 07:48 UTC #3 lore raw

Dear Radha Krishna,

Quoted 5 lines · In message <[email protected]> you wrote:

As you suggested I have DOS to UNIX conversion. It worked. I have another proble now.
make: arm-none-linux-gnueabi-gcc: Command not found

...

Quoted 1 line

Could please somebody tell me the solution for this.

You must install the arm-none-linux-gnueabitoolchain on your host system, and set up the PATH to include the directories wher eit was installed.

Best regards,

Wolfgang Denk

Signature · 4 lines

DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Ahead warp factor 1"                                  - Captain Kirk

Radha Krishna

2008-10-18 16:57 UTC #4 lore raw

Hi Wolfgang Denk,

Thanks for the help.

Could you tell URL to download this toll chain arm-none-linux-gnueabi

Best Regards,
Kris.

Quoted 25 lines · Wolfgang Denk

From: Wolfgang Denk <[email protected]>
Subject: Re: [U-Boot] [U-Boot-Users] Compilation problem for TI3430 board.
To: hi_krishna01 at yahoo.com
Cc: "U-Boot user list" <[email protected]>
Date: Saturday, October 18, 2008, 12:48 AM
Dear Radha Krishna,
In message
<[email protected]> you
Quoted 2 lines · wrote:
As you suggested I have DOS to UNIX conversion. It
worked.
Quoted 3 lines
I have another proble now.
make: arm-none-linux-gnueabi-gcc: Command not found
...
Quoted 1 line
Could please somebody tell me the solution for this.
You must install the arm-none-linux-gnueabitoolchain on your host
system, and set up the PATH to include the directories wher eit was
installed.

Quoted 13 lines

Best regards,

Wolfgang Denk

Signature · 8 lines

DENX Software Engineering GmbH,     MD: Wolfgang Denk &
Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194
Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email:
wd at denx.de
"Ahead warp factor 1"                            
     - Captain Kirk

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com