Skip to contentSkip to conversation

net: phy: at803x: disable delay only for RGMII mode

PATCH In review Vinod Koul 7 participants 19 messages Feb 12, 2019 – Feb 15, 2019

Subsystems (4)
lore
Share & tools
lore

Vinod Koul

author
#0 lore raw

PATCH 1/1 net: phy: at803x: disable delay only for RGMII mode

Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID can have delay in phy.

So disable the delay only for RGMII mode and disable for other modes

Fixes cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
---
 drivers/net/phy/at803x.c | 33 ++++++++++++++++++++++++++-------
 1 file changed, 26 insertions(+), 7 deletions(-)
drivers/net/phy/at803x.c +26 -7
index 8ff12938ab47..7b54b54e3316 100644
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+
 static inline int at803x_disable_rx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
@@ -255,18 +267,25 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII) {
 		ret = at803x_disable_rx_delay(phydev);
 		if (ret < 0)
 			return ret;
+		ret = at803x_disable_tx_delay(phydev);
+		if (ret < 0)
+			return ret;
+	};
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		ret = at803x_enable_rx_delay(phydev);
+		if (ret < 0)
+			return ret;
 	}
 
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
-		ret = at803x_disable_tx_delay(phydev);
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+		ret = at803x_enable_tx_delay(phydev);
 		if (ret < 0)
 			return ret;
 	}
Signature · 1 line
2.20.1
Tested-by on v1 1/1
#1 lore raw

Hi Vinod,

Quoted 5 lines · Vinod Koul

Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID can have delay in phy.

So disable the delay only for RGMII mode and disable for other modes

s/disable for other modes/enable for other modes

Works fine on am335x-evmsk:

and few comment

Quoted 12 lines
Fixes cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
---
 drivers/net/phy/at803x.c | 33 ++++++++++++++++++++++++++-------
 1 file changed, 26 insertions(+), 7 deletions(-)
drivers/net/phy/at803x.c +0 -0
index 8ff12938ab47..7b54b54e3316 100644

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 117

Quoted 8 lines
drivers/net/phy/at803x.c +5 -0
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}

static inline int at803x_select_rx_delay(struct phy_device *phydev,
bool enable)
{
}

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 123

Quoted 6 lines
drivers/net/phy/at803x.c +6 -0
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}

static inline int at803x_select_tx_delay(struct phy_device *phydev,
bool enable)
{
}

perhaps?

Quoted 8 lines
drivers/net/phy/at803x.c +1 -0
+
 static inline int at803x_disable_rx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
@@ -255,18 +267,25 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 

drivers/net/phy/at803x.c static int at803x_config_init(struct phy_device *phydev) · line 276

Quoted 10 lines
drivers/net/phy/at803x.c +4 -3
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII) {
 		ret = at803x_disable_rx_delay(phydev);
 		if (ret < 0)
 			return ret;
+		ret = at803x_disable_tx_delay(phydev);
+		if (ret < 0)
+			return ret;

is it a possibility to have PHY_INTERFACE_MODE_RGMII and other RGMII_ID || RGMII_TXID || RGMII_RXID set at the same time?

if not you can just return from here, no need to check for other RGMII modes?

Quoted 10 lines
drivers/net/phy/at803x.c +7 -0
+	};
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		ret = at803x_enable_rx_delay(phydev);
+		if (ret < 0)
+			return ret;
 	}
 

drivers/net/phy/at803x.c static int at803x_config_init(struct phy_device *phydev) · line 291

Quoted 10 lines
drivers/net/phy/at803x.c +3 -4
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
-		ret = at803x_disable_tx_delay(phydev);
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+		ret = at803x_enable_tx_delay(phydev);
 		if (ret < 0)
 			return ret;
 	}

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

author
#2 lore raw
Quoted 9 lines · Peter Ujfalusi

Hi Vinod,

Quoted 5 lines · Vinod Koul

Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID can have delay in phy.

So disable the delay only for RGMII mode and disable for other modes

s/disable for other modes/enable for other modes

oops

Quoted 3 lines

Works fine on am335x-evmsk:

Thanks for quick testing..

Quoted 41 lines

and few comment

Quoted 12 lines
Fixes cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
---
 drivers/net/phy/at803x.c | 33 ++++++++++++++++++++++++++-------
 1 file changed, 26 insertions(+), 7 deletions(-)
drivers/net/phy/at803x.c +0 -0
index 8ff12938ab47..7b54b54e3316 100644

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 117

Quoted 8 lines
drivers/net/phy/at803x.c +5 -0
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}

static inline int at803x_select_rx_delay(struct phy_device *phydev,
bool enable)
{
}

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 123

Quoted 6 lines
drivers/net/phy/at803x.c +6 -0
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}

static inline int at803x_select_tx_delay(struct phy_device *phydev,
bool enable)
{
}

Quoted 1 line

perhaps?

Given that we would again branch off on enable, I see this as no better case so I will keep existing

Quoted 9 lines
Quoted 9 lines
drivers/net/phy/at803x.c +1 -0
+
 static inline int at803x_disable_rx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
@@ -255,18 +267,25 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
Quoted 13 lines

drivers/net/phy/at803x.c static int at803x_config_init(struct phy_device *phydev) · line 276

Quoted 10 lines
drivers/net/phy/at803x.c +4 -3
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII) {
 		ret = at803x_disable_rx_delay(phydev);
 		if (ret < 0)
 			return ret;
+		ret = at803x_disable_tx_delay(phydev);
+		if (ret < 0)
+			return ret;

is it a possibility to have PHY_INTERFACE_MODE_RGMII and other RGMII_ID || RGMII_TXID || RGMII_RXID set at the same time?

Nope that would not make sense

Quoted 2 lines

if not you can just return from here, no need to check for other RGMII modes?

for RGMII yes indeed..

Signature · 1 line
~Vinod
#3 lore raw
In reply to Vinod Koul
Quoted 59 lines · Vinod Koul

Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID can have delay in phy.

So disable the delay only for RGMII mode and disable for other modes

Fixes cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
---
 drivers/net/phy/at803x.c | 33 ++++++++++++++++++++++++++-------
 1 file changed, 26 insertions(+), 7 deletions(-)
drivers/net/phy/at803x.c +23 -3
index 8ff12938ab47..7b54b54e3316 100644
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+
 static inline int at803x_disable_rx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
@@ -255,18 +267,25 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII) {
 		ret = at803x_disable_rx_delay(phydev);
 		if (ret < 0)
 			return ret;
+		ret = at803x_disable_tx_delay(phydev);
+		if (ret < 0)
+			return ret;
+	};
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		ret = at803x_enable_rx_delay(phydev);
+		if (ret < 0)
+			return ret;
 	}
 

drivers/net/phy/at803x.c static int at803x_config_init(struct phy_device *phydev) · line 291

Quoted 10 lines
drivers/net/phy/at803x.c +3 -4
-	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
-		ret = at803x_disable_tx_delay(phydev);
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+		ret = at803x_enable_tx_delay(phydev);
 		if (ret < 0)
 			return ret;
 	}

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

Thus it will use the default value of the PHY, and for this PHY both TX and RX delays are enabled by default.

This means that someone specifying PHY_INTERFACE_MODE_RGMII_TXID will actually be getting PHY_INTERFACE_MODE_RGMII_ID.

Marc's patch:
https://www.spinics.net/lists/netdev/msg445053.html

does explicitly either enable or disable each delay (so it does not depend on default values).

However, Marc's patch was never merged, because someone reported a regression on am335x-evm.

On Vinod's V1 submission Andrew replied that if this change breaks some existing DT (because that DT specifies a phy-mode that does not match with reality), then we should fix so that DT specifies the correct phy-mode:
https://www.spinics.net/lists/netdev/msg542638.html

IMHO, this makes most sense, since if a DT specifies an incorrect phy-mode, then that is what the user should get.

Kind regards,
Niklas

maintainer
#4 lore raw
Quoted 10 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

Andrew

#5 lore raw
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Regards.

#6 lore raw
Quoted 18 lines · Marc Gonzalez
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

Quoted 5 lines

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Hello Marc,

I saw that comment from Florian. However that was way back in 2017. Maybe the phy-modes were not as well defined back then?

Andrew recently suggested to fix the driver so that it conforms with the phy-modes, and fix any SoC that specified an incorrect phy-mode in DT and thus relied upon the broken behavior of the PHY driver:
https://www.spinics.net/lists/netdev/msg445133.html

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

am335x-evm appears to rely on the current broken behavior of the PHY driver, so we will probably need to fix the am335x-evm according to this:
https://www.spinics.net/lists/netdev/msg445117.html
and merge that as well.

Andrew, Florian, do you both agree?

Kind regards,
Niklas

Quoted 1 line

From 7f19f32d3074c9990e46349b76ae13dc9c1133d6 Mon Sep 17 00:00:00 2001

From: Marc Gonzalez <[email protected]>
Date: Wed, 13 Feb 2019 18:29:02 +0100
Subject: [PATCH] net: phy: at803x: Fix RGMII RX and TX clock delays setup

The current code supports enabling RGMII RX and TX clock delays. The unstated assumption is that these settings are disabled by default at reset, which is not the case.

RX clock delay is enabled at reset. And TX clock delay "survives" across SW resets. Thus, if the bootloader enables TX clock delay, it will remain enabled at reset in Linux.

Provide disable functions to configure the RGMII clock delays exactly as specified in the fwspec.

Fixes cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
---
 drivers/net/phy/at803x.c | 34 ++++++++++++++++++++++++----------
 1 file changed, 24 insertions(+), 10 deletions(-)
drivers/net/phy/at803x.c +24 -10
index 90dc62c15fc5..700c1e4d34ad 100644
@@ -103,12 +103,24 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
 static inline int at803x_disable_rx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
 				     AT803X_DEBUG_RX_CLK_DLY_EN, 0);
 }
 
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+
 static inline int at803x_disable_tx_delay(struct phy_device *phydev)
 {
 	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5,
@@ -242,20 +254,22 @@ static int at803x_config_init(struct phy_device *phydev)
 		return ret;
 
 	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
+		ret = at803x_enable_rx_delay(phydev);
+	else
 		ret = at803x_disable_rx_delay(phydev);
-		if (ret < 0)
-			return ret;
-	}
+
+	if (ret < 0)
+		return ret;
 
 	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
-			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
+		ret = at803x_enable_tx_delay(phydev);
+	else
 		ret = at803x_disable_tx_delay(phydev);
-		if (ret < 0)
-			return ret;
-	}
+
+	if (ret < 0)
+		return ret;
 
 	return 0;
 }
Signature · 1 line
2.20.1
#7 lore raw
Quoted 22 lines · Niklas Cassel
Quoted 21 lines · Marc Gonzalez
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

Quoted 7 lines
Quoted 2 lines

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Hello Marc,

I saw that comment from Florian. However that was way back in 2017. Maybe the phy-modes were not as well defined back then?

The definition of the 'phy-mode' was clarified to be understood from the perspective of the PHY device (hence the name) after we had several fruitful exchanges with Marc (at least from my perspective), but since the definition was not clear before, there is a high chance of finding DTS/DTBs out there with the 'phy-mode' property understood from the MAC's perspective, which would now be wrong.

Quoted 10 lines

Andrew recently suggested to fix the driver so that it conforms with the phy-modes, and fix any SoC that specified an incorrect phy-mode in DT and thus relied upon the broken behavior of the PHY driver:
https://www.spinics.net/lists/netdev/msg445133.html

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

Quoted 7 lines

am335x-evm appears to rely on the current broken behavior of the PHY driver, so we will probably need to fix the am335x-evm according to this:
https://www.spinics.net/lists/netdev/msg445117.html
and merge that as well.

Andrew, Florian, do you both agree?

In my reply to Marc, there was a concern that while am335x-evm was identified and reported to be broken after fixing the PHY driver, there could be platforms out there that we have little to no visibility that would most likely be equally broken. That concern still exists, and I don't think there is anything we can do to even assess the size of the problem unless we attempt to fix it, so maybe we should attempt to fix that.

There was a suggestion to Marc that one way to possibly "ignore" an incorrectly broken 'phy-mode' property would be to allow specifying rx/tx delay properties such that if the driver obtained its phy_interface_t, yet still parsed rx/tx delays, the rx/tx delays would take precedence, and we could possibly derive some sort of a "more correct" phy_interface_t that we could assign back to phydev->interface and issue a warning about that.

Another possible way to resolve that could be to introduce a 'mac-mode' property, which must be strictly compatible with specifying a 'phy-mode' property. For instance:

- MAC specifies mac-mode = 'rgmii-id', then the PHY must have phy-mode = 'rmgii' since the MAC is taking of inserting both RX and TX delays, reverse also applies

- MAC specifies mac-mode = 'rgmii-txid', then the PHY must have phy-mode = 'rgmii-rxid' because the MAC adds the TX delay, but the PHY should insert the delay on the RX lines, reverse also applies

Because there is usually (not always, DSA is an exception) a 1:1 mapping between MAC and PHY devices we could look up the 'mac-mode' property in the MAC in the PHY library code and make sure that we have a compatible matrix and if we do not, maybe pass something like PHY_INTERFACE_MODE_NA such that the driver retains its settings.

Maybe another way to approach this is if we assume that the PHY comes up configured correctly by the boot loader, or upon power on reset, we add some PHY driver methods that allow us to determine the RGMII mode in which a PHY is and that tells us whether we are compatible with the MAC's phy_interface_t upon connection. We check both at connect() time and if something does not look right, we flip the meaning of phy_interface_t.

None of those solutions are entirely fool proof, but at least we might be able to detect incorrect combinations, yet still make them work by reversing the meaning of the 'phy-mode' property given information at hand.

Let me know if none of that makes sense and this just looks like yet another brain dump.

Wonderful RGMII...

Signature · 1 line
Florian
#8 lore raw
Quoted 31 lines · Florian Fainelli
Quoted 22 lines · Niklas Cassel
Quoted 21 lines · Marc Gonzalez
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

Quoted 7 lines
Quoted 2 lines

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Hello Marc,

I saw that comment from Florian. However that was way back in 2017. Maybe the phy-modes were not as well defined back then?

Quoted 6 lines

The definition of the 'phy-mode' was clarified to be understood from the perspective of the PHY device (hence the name) after we had several fruitful exchanges with Marc (at least from my perspective), but since the definition was not clear before, there is a high chance of finding DTS/DTBs out there with the 'phy-mode' property understood from the MAC's perspective, which would now be wrong.

Hello Florian,

We have a specification:
Documentation/devicetree/bindings/net/ethernet.txt

And several implementations: the PHY drivers.

Either we decide that all PHY drivers have to follow the specification for "phy-mode" in Documentation/devicetree/bindings/net/ethernet.txt or we decide that they don't.

If we decide that all PHY drivers have to follow the specification, then we can fix the PHY drivers that currently do not follow the specification.

If we decide that all PHY drivers do not have to follow the spec, then the "phy-mode" property is basically useless, and then we should introduce a new device tree property, e.g. "phy-mode2", that is guaranteed to respect the definitons in Documentation/devicetree/bindings/net/ethernet.txt

Quoted 27 lines
Quoted 12 lines

Andrew recently suggested to fix the driver so that it conforms with the phy-modes, and fix any SoC that specified an incorrect phy-mode in DT and thus relied upon the broken behavior of the PHY driver:
https://www.spinics.net/lists/netdev/msg445133.html

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

Quoted 7 lines

am335x-evm appears to rely on the current broken behavior of the PHY driver, so we will probably need to fix the am335x-evm according to this:
https://www.spinics.net/lists/netdev/msg445117.html
and merge that as well.

Andrew, Florian, do you both agree?

In my reply to Marc, there was a concern that while am335x-evm was identified and reported to be broken after fixing the PHY driver, there could be platforms out there that we have little to no visibility that would most likely be equally broken. That concern still exists, and I don't think there is anything we can do to even assess the size of the problem unless we attempt to fix it, so maybe we should attempt to fix that.

Quoted 7 lines

There was a suggestion to Marc that one way to possibly "ignore" an incorrectly broken 'phy-mode' property would be to allow specifying rx/tx delay properties such that if the driver obtained its phy_interface_t, yet still parsed rx/tx delays, the rx/tx delays would take precedence, and we could possibly derive some sort of a "more correct" phy_interface_t that we could assign back to phydev->interface and issue a warning about that.

You mean to add new device tree properties to Documentation/devicetree/bindings/net/ethernet.txt

- phy-id-tx: "true" if PHY should add internal delay on TX lines; "false" or not specified if PHY should not add internal delay on TX lines. This property overrides any delay requested by "phy-mode".
- phy-id-rx: "true" if PHY should add internal delay on RX lines; "false" or not specified if PHY should not add internal delay on RX lines. This property overrides any delay requested by "phy-mode".

Perhaps something like that?

Personally, I prefer making "phy-mode" strict,
but whatever you guys decide:
- making "phy-mode" strict
- introducing a "phy-mode2"
- introducing "phy-id-tx/phy-id-rx"
- introducing "mac-mode"
- some other solution

It is probably wise to introduce helper functions in phy.h
phy_wants_id_rx()
phy_wants_id_tx()
so that PHY drivers can simply use e.g.:

if (phy_wants_id_rx(phydev))

	at803x_enable_rx_delay(phydev);
else
	at803x_disable_rx_delay(phydev);

if (phy_wants_id_tx(phydev))

	at803x_enable_tx_delay(phydev);
else
	at803x_disable_tx_delay(phydev);
Quoted 13 lines

Another possible way to resolve that could be to introduce a 'mac-mode' property, which must be strictly compatible with specifying a 'phy-mode' property. For instance:

- MAC specifies mac-mode = 'rgmii-id', then the PHY must have phy-mode = 'rmgii' since the MAC is taking of inserting both RX and TX delays, reverse also applies

- MAC specifies mac-mode = 'rgmii-txid', then the PHY must have phy-mode = 'rgmii-rxid' because the MAC adds the TX delay, but the PHY should insert the delay on the RX lines, reverse also applies

Quoted 5 lines

Because there is usually (not always, DSA is an exception) a 1:1 mapping between MAC and PHY devices we could look up the 'mac-mode' property in the MAC in the PHY library code and make sure that we have a compatible matrix and if we do not, maybe pass something like PHY_INTERFACE_MODE_NA such that the driver retains its settings.

Is there any advantage of creating a "mac-mode" over creating a "phy-mode2" ?

Kind regards,
Niklas

Quoted 19 lines

Maybe another way to approach this is if we assume that the PHY comes up configured correctly by the boot loader, or upon power on reset, we add some PHY driver methods that allow us to determine the RGMII mode in which a PHY is and that tells us whether we are compatible with the MAC's phy_interface_t upon connection. We check both at connect() time and if something does not look right, we flip the meaning of phy_interface_t.

None of those solutions are entirely fool proof, but at least we might be able to detect incorrect combinations, yet still make them work by reversing the meaning of the 'phy-mode' property given information at hand.

Let me know if none of that makes sense and this just looks like yet another brain dump.

Wonderful RGMII...

Signature · 1 line
Florian
#9 lore raw
Quoted 56 lines · Niklas Cassel
Quoted 31 lines · Florian Fainelli
Quoted 22 lines · Niklas Cassel
Quoted 21 lines · Marc Gonzalez
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

Quoted 7 lines
Quoted 2 lines

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Hello Marc,

I saw that comment from Florian. However that was way back in 2017. Maybe the phy-modes were not as well defined back then?

Quoted 6 lines

The definition of the 'phy-mode' was clarified to be understood from the perspective of the PHY device (hence the name) after we had several fruitful exchanges with Marc (at least from my perspective), but since the definition was not clear before, there is a high chance of finding DTS/DTBs out there with the 'phy-mode' property understood from the MAC's perspective, which would now be wrong.

Hello Florian,

We have a specification:
Documentation/devicetree/bindings/net/ethernet.txt

And several implementations: the PHY drivers.

Either we decide that all PHY drivers have to follow the specification for "phy-mode" in Documentation/devicetree/bindings/net/ethernet.txt or we decide that they don't.

If we decide that all PHY drivers have to follow the specification, then we can fix the PHY drivers that currently do not follow the specification.

Quoted 5 lines

If we decide that all PHY drivers do not have to follow the spec, then the "phy-mode" property is basically useless, and then we should introduce a new device tree property, e.g. "phy-mode2", that is guaranteed to respect the definitons in Documentation/devicetree/bindings/net/ethernet.txt

If the specification had been clear from day one, then we would not be in the situation we are in today, so in that case it is not as simple
as: a) deprecating an existing property that was misused because the spec was not well enough defined and b) go and fix all drivers. The amount of breakage that can be introduced is just immense, and quite frankly, for absolutely no good reason.

It's all well and good to introduce a 'phy-mode2' but let's think about the future:

- what is depreciation path for 'phy-mode'/'phy-connection-type' looking like then?
- do we have the manpower to review every new binding, DTS submission that gets included in Linux, FreeBSD, Zephyr, for correctness?

Quoted 48 lines
Quoted 28 lines
Quoted 13 lines

Andrew recently suggested to fix the driver so that it conforms with the phy-modes, and fix any SoC that specified an incorrect phy-mode in DT and thus relied upon the broken behavior of the PHY driver:
https://www.spinics.net/lists/netdev/msg445133.html

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

Quoted 7 lines

am335x-evm appears to rely on the current broken behavior of the PHY driver, so we will probably need to fix the am335x-evm according to this:
https://www.spinics.net/lists/netdev/msg445117.html
and merge that as well.

Andrew, Florian, do you both agree?

In my reply to Marc, there was a concern that while am335x-evm was identified and reported to be broken after fixing the PHY driver, there could be platforms out there that we have little to no visibility that would most likely be equally broken. That concern still exists, and I don't think there is anything we can do to even assess the size of the problem unless we attempt to fix it, so maybe we should attempt to fix that.

Quoted 7 lines

There was a suggestion to Marc that one way to possibly "ignore" an incorrectly broken 'phy-mode' property would be to allow specifying rx/tx delay properties such that if the driver obtained its phy_interface_t, yet still parsed rx/tx delays, the rx/tx delays would take precedence, and we could possibly derive some sort of a "more correct" phy_interface_t that we could assign back to phydev->interface and issue a warning about that.

You mean to add new device tree properties to Documentation/devicetree/bindings/net/ethernet.txt

- phy-id-tx: "true" if PHY should add internal delay on TX lines; "false" or not specified if PHY should not add internal delay on TX lines. This property overrides any delay requested by "phy-mode".
- phy-id-rx: "true" if PHY should add internal delay on RX lines; "false" or not specified if PHY should not add internal delay on RX lines. This property overrides any delay requested by "phy-mode".

Quoted 1 line

Perhaps something like that?

Not quite booleans, actual delay values, e.g.:

tx-delay-ps = <2000>
rx-delay-ps = <2000>

this is something that exists already:

Documentation/devicetree/bindings/net/apm-xgene-enet.txt Documentation/devicetree/bindings/net/cavium-pip.txt Documentation/devicetree/bindings/net/dwmac-sun8i.txt

because conceptually, telling the PHY driver that a TX or RX delay is simply not enough, sometimes the standard 2ns (90 degree shift at 125Mhz) is not good enough and gets you out of spec because of some board design.

Quoted 15 lines

Personally, I prefer making "phy-mode" strict,
but whatever you guys decide:
- making "phy-mode" strict
- introducing a "phy-mode2"
- introducing "phy-id-tx/phy-id-rx"
- introducing "mac-mode"
- some other solution

It is probably wise to introduce helper functions in phy.h
phy_wants_id_rx()
phy_wants_id_tx()
so that PHY drivers can simply use e.g.:

if (phy_wants_id_rx(phydev))

Quoted 8 lines
	at803x_enable_rx_delay(phydev);
else
	at803x_disable_rx_delay(phydev);

if (phy_wants_id_tx(phydev))

	at803x_enable_tx_delay(phydev);
else
	at803x_disable_tx_delay(phydev);

Yes, that I think is pretty much orthogonal to the end solution we decide to choose, having a way to tell what the PHY is currently configured, or capable of supporting is step 1 in trying to find a compatibility solution.

Quoted 46 lines
Quoted 14 lines

Another possible way to resolve that could be to introduce a 'mac-mode' property, which must be strictly compatible with specifying a 'phy-mode' property. For instance:

- MAC specifies mac-mode = 'rgmii-id', then the PHY must have phy-mode = 'rmgii' since the MAC is taking of inserting both RX and TX delays, reverse also applies

- MAC specifies mac-mode = 'rgmii-txid', then the PHY must have phy-mode = 'rgmii-rxid' because the MAC adds the TX delay, but the PHY should insert the delay on the RX lines, reverse also applies

Quoted 5 lines

Because there is usually (not always, DSA is an exception) a 1:1 mapping between MAC and PHY devices we could look up the 'mac-mode' property in the MAC in the PHY library code and make sure that we have a compatible matrix and if we do not, maybe pass something like PHY_INTERFACE_MODE_NA such that the driver retains its settings.

Is there any advantage of creating a "mac-mode" over creating a "phy-mode2" ?

Kind regards,
Niklas

Quoted 19 lines

Maybe another way to approach this is if we assume that the PHY comes up configured correctly by the boot loader, or upon power on reset, we add some PHY driver methods that allow us to determine the RGMII mode in which a PHY is and that tells us whether we are compatible with the MAC's phy_interface_t upon connection. We check both at connect() time and if something does not look right, we flip the meaning of phy_interface_t.

None of those solutions are entirely fool proof, but at least we might be able to detect incorrect combinations, yet still make them work by reversing the meaning of the 'phy-mode' property given information at hand.

Let me know if none of that makes sense and this just looks like yet another brain dump.

Wonderful RGMII...

Signature · 1 line
Florian
Signature · 1 line
Florian
#10 lore raw
In reply to Niklas Cassel

Hi Niklas,

Quoted 30 lines · Niklas Cassel
Quoted 18 lines · Marc Gonzalez
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

Quoted 5 lines

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Hello Marc,

I saw that comment from Florian. However that was way back in 2017. Maybe the phy-modes were not as well defined back then?

Quoted 8 lines

Andrew recently suggested to fix the driver so that it conforms with the phy-modes, and fix any SoC that specified an incorrect phy-mode in DT and thus relied upon the broken behavior of the PHY driver:
https://www.spinics.net/lists/netdev/msg445133.html

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

with the patch + s/rgmii-txid/rgmii-id in the am335x-evmsk.dts ethernet is working.
I don't have am335x-evm to test, but it has the same PHY as evmsk.

Quoted 6 lines

am335x-evm appears to rely on the current broken behavior of the PHY driver, so we will probably need to fix the am335x-evm according to this:
https://www.spinics.net/lists/netdev/msg445117.html
and merge that as well.

Quoted 6 lines

Andrew, Florian, do you both agree?

Kind regards,
Niklas

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

#11 lore raw
Quoted 39 lines · Peter Ujfalusi

Hi Niklas,

Quoted 36 lines · Niklas Cassel
Quoted 18 lines · Marc Gonzalez
Quoted 7 lines · Andrew Lunn
Quoted 7 lines

So we have these modes:

PHY_INTERFACE_MODE_RGMII: TX and RX delays disabled PHY_INTERFACE_MODE_RGMII_ID: TX and RX delays enabled PHY_INTERFACE_MODE_RGMII_RXID: RX delay enabled, TX delay disabled PHY_INTERFACE_MODE_RGMII_TXID: TX delay enabled, RX delay disabled

Quoted 8 lines
Quoted 3 lines

What I don't like with this patch, is that if we specify phy-mode PHY_INTERFACE_MODE_RGMII_TXID, this patch will enable TX delay, but RX delay will not be explicitly set.

That is not the behaviour we want. It is best to assume the device is in a random state, and correctly enable/disable all delays as requested. Only leave the hardware alone if PHY_INTERFACE_MODE_NA is used.

Quoted 5 lines

That's what my patch did:
https://www.spinics.net/lists/netdev/msg445053.html

But see Florian's remarks:
https://www.spinics.net/lists/netdev/msg445133.html

Hello Marc,

I saw that comment from Florian. However that was way back in 2017. Maybe the phy-modes were not as well defined back then?

Andrew recently suggested to fix the driver so that it conforms with the phy-modes, and fix any SoC that specified an incorrect phy-mode in DT and thus relied upon the broken behavior of the PHY driver:
https://www.spinics.net/lists/netdev/msg445133.html

Quoted 7 lines
Quoted 2 lines

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

with the patch + s/rgmii-txid/rgmii-id in the am335x-evmsk.dts ethernet is working.
I don't have am335x-evm to test, but it has the same PHY as evmsk.

Florian's concern was that this PHY driver looked at "phy-mode" from the perspective of the MAC rather than the PHY.
However, if s/rgmii-txid/rgmii-id is the correct fix for am335x-evm, then this means that this PHY driver was just broken.

If the driver had misinterpreted the perspective, then the correct fix for am335x-evm would have been s/rgmii-txid/rgmii-rxid.

So considering that this driver seems to be really broken (rather then just inverted perspective),
perhaps we can merge the patch I attached in my previous email after all? (Together with a s/rgmii-txid/rgmii-id in the am335x-evmsk.dts.)

Kind regards,
Niklas

Quoted 17 lines
Quoted 6 lines

am335x-evm appears to rely on the current broken behavior of the PHY driver, so we will probably need to fix the am335x-evm according to this:
https://www.spinics.net/lists/netdev/msg445117.html
and merge that as well.

Quoted 6 lines

Andrew, Florian, do you both agree?

Kind regards,
Niklas

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

#12 lore raw

Hi Niklas,

Quoted 8 lines · Niklas Cassel
Quoted 7 lines
Quoted 2 lines

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

with the patch + s/rgmii-txid/rgmii-id in the am335x-evmsk.dts ethernet is working.
I don't have am335x-evm to test, but it has the same PHY as evmsk.

Quoted 7 lines

Florian's concern was that this PHY driver looked at "phy-mode" from the perspective of the MAC rather than the PHY.
However, if s/rgmii-txid/rgmii-id is the correct fix for am335x-evm, then this means that this PHY driver was just broken.

If the driver had misinterpreted the perspective, then the correct fix for am335x-evm would have been s/rgmii-txid/rgmii-rxid.

Not sure if I got this right, but:
rgmii-id/txid/rxid is the delay mode between PHY and MAC, right? on the PHY node it is from the PHY perspective, right?

The errata I have mentioned for am335x say:
"The reset state of RGMII1_IDMODE (bit 4) and RGMII2_IDMODE (bit 5) in the GMII_SEL register enables internal delay mode on the transmit clock of the respective RGMII port. The AM335x device does not support internal delay mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1b."

If the delay mode on the transmit clock is not working on the am335x, then this translate that the rxid needs to be enabled on the PHY side?

But then why it worked when only the txid was enabled and rxid was not on the PHY side, and why it works if both txid and rxid is enabled?

Just tried w/ your patch and setting rgmii-rxid for am335x-evmsk and ethernet is not working, it only works w/ rgmii-id (so both tx and rx delay is enabled on the PHY side?)

Quoted 4 lines

So considering that this driver seems to be really broken (rather then just inverted perspective),
perhaps we can merge the patch I attached in my previous email after all? (Together with a s/rgmii-txid/rgmii-id in the am335x-evmsk.dts.)

at the same time am335x-evm.dts needs to have the same change and most likely other boards which uses the same PHY needs to be checked?

PS: sorry for my lack of knowledge on the networking stuff...

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

#13 lore raw
Quoted 16 lines · Peter Ujfalusi

Hi Niklas,

Quoted 13 lines · Niklas Cassel
Quoted 7 lines
Quoted 2 lines

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

with the patch + s/rgmii-txid/rgmii-id in the am335x-evmsk.dts ethernet is working.
I don't have am335x-evm to test, but it has the same PHY as evmsk.

Florian's concern was that this PHY driver looked at "phy-mode" from the perspective of the MAC rather than the PHY.
However, if s/rgmii-txid/rgmii-id is the correct fix for am335x-evm, then this means that this PHY driver was just broken.

Quoted 6 lines
Quoted 2 lines

If the driver had misinterpreted the perspective, then the correct fix for am335x-evm would have been s/rgmii-txid/rgmii-rxid.

Not sure if I got this right, but:
rgmii-id/txid/rxid is the delay mode between PHY and MAC, right? on the PHY node it is from the PHY perspective, right?

Yes, from the PHY perspective.

(According to Florian, IIUC, some old PHY drivers were implemented before it was decided that it is from PHY perspective, rather than from MAC perspective.)

Quoted 9 lines

The errata I have mentioned for am335x say:
"The reset state of RGMII1_IDMODE (bit 4) and RGMII2_IDMODE (bit 5) in the GMII_SEL register enables internal delay mode on the transmit clock of the respective RGMII port. The AM335x device does not support internal delay mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1b."

If the delay mode on the transmit clock is not working on the am335x, then this translate that the rxid needs to be enabled on the PHY side?

IIUC what Florian explained, then either MAC or PHY needs to add delays, so if the PHY only adds delay on e.g. TX, then the MAC needs to add delay on RX.

However, in your case, the errata says that your MAC is not capable of adding a delay on TX, therefore the PHY needs to add a delay on TX.

Quoted 3 lines

But then why it worked when only the txid was enabled and rxid was not on the PHY side, and why it works if both txid and rxid is enabled?

Because the PHY driver was broken, so the PHY driver always enabled delays on both TX and RX.

This is how the driver looked before Vinod's change:

        if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
                        phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
                ret = at803x_enable_rx_delay(phydev);
                if (ret < 0)
                        return ret;
        }
 
        if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
                        phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
                ret = at803x_enable_tx_delay(phydev);
                if (ret < 0)
                        return ret;
        }

Yet, the initial value for this PHY is that both TX and RX delay is enabled, and since this driver never disabled TX/RX delays, the TX and RX delays were always enabled, no matter what phy-mode you specified.

Quoted 19 lines

Just tried w/ your patch and setting rgmii-rxid for am335x-evmsk and ethernet is not working, it only works w/ rgmii-id (so both tx and rx delay is enabled on the PHY side?)

Quoted 4 lines

So considering that this driver seems to be really broken (rather then just inverted perspective),
perhaps we can merge the patch I attached in my previous email after all? (Together with a s/rgmii-txid/rgmii-id in the am335x-evmsk.dts.)

at the same time am335x-evm.dts needs to have the same change and most likely other boards which uses the same PHY needs to be checked?

PS: sorry for my lack of knowledge on the networking stuff...

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

#14 lore raw
Quoted 40 lines · Niklas Cassel
Quoted 16 lines · Peter Ujfalusi

Hi Niklas,

Quoted 13 lines · Niklas Cassel
Quoted 7 lines
Quoted 2 lines

So, I've rebased your old patch, see attachment.
I suggest that Peter test it on am335x-evm.

with the patch + s/rgmii-txid/rgmii-id in the am335x-evmsk.dts ethernet is working.
I don't have am335x-evm to test, but it has the same PHY as evmsk.

Florian's concern was that this PHY driver looked at "phy-mode" from the perspective of the MAC rather than the PHY.
However, if s/rgmii-txid/rgmii-id is the correct fix for am335x-evm, then this means that this PHY driver was just broken.

Quoted 6 lines
Quoted 2 lines

If the driver had misinterpreted the perspective, then the correct fix for am335x-evm would have been s/rgmii-txid/rgmii-rxid.

Not sure if I got this right, but:
rgmii-id/txid/rxid is the delay mode between PHY and MAC, right? on the PHY node it is from the PHY perspective, right?

Yes, from the PHY perspective.

(According to Florian, IIUC, some old PHY drivers were implemented before it was decided that it is from PHY perspective, rather than from MAC perspective.)

Quoted 9 lines

The errata I have mentioned for am335x say:
"The reset state of RGMII1_IDMODE (bit 4) and RGMII2_IDMODE (bit 5) in the GMII_SEL register enables internal delay mode on the transmit clock of the respective RGMII port. The AM335x device does not support internal delay mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1b."

If the delay mode on the transmit clock is not working on the am335x, then this translate that the rxid needs to be enabled on the PHY side?

Quoted 6 lines

IIUC what Florian explained, then either MAC or PHY needs to add delays, so if the PHY only adds delay on e.g. TX, then the MAC needs to add delay on RX.

However, in your case, the errata says that your MAC is not capable of adding a delay on TX, therefore the PHY needs to add a delay on TX.

So that mandates specifying either 'rgmii-id' or 'rgmii-txid'.

Quoted 25 lines
Quoted 4 lines

But then why it worked when only the txid was enabled and rxid was not on the PHY side, and why it works if both txid and rxid is enabled?

Because the PHY driver was broken, so the PHY driver always enabled delays on both TX and RX.

This is how the driver looked before Vinod's change:

        if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
                        phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
                ret = at803x_enable_rx_delay(phydev);
                if (ret < 0)
                        return ret;
        }
 
        if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
                        phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
                ret = at803x_enable_tx_delay(phydev);
                if (ret < 0)
                        return ret;
        }
Quoted 4 lines

Yet, the initial value for this PHY is that both TX and RX delay is enabled, and since this driver never disabled TX/RX delays, the TX and RX delays were always enabled, no matter what phy-mode you specified.

Fixing all PHY drivers is probably too much, but since we seem to have traction and people assigned to QCOM working on this at803x PHY driver, then let's fix it correctly, I agree with that. So that means:

- disable both RX and TX delay by default
- if RGMII_RXID or RGMII_ID is specified: turn on RX delay
- if RGMII_TXID or RGMII_ID is specified: turn on TX delay

so basically the patch above, with an initial delay disabling for both RX and TX. Then we fix all DTSes to be correct, at least those in tree and we provide appropriate Fixes: tag so things get backported automatically.

How does that sound?

Signature · 1 line
Florian
maintainer
#15 lore raw
In reply to Vinod Koul

From: Vinod Koul <[email protected]>
Date: Tue, 12 Feb 2019 19:49:22 +0530

Quoted 10 lines
drivers/net/phy/at803x.c +2 -0
index 8ff12938ab47..7b54b54e3316 100644
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 124

Quoted 10 lines
drivers/net/phy/at803x.c +10 -0
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+

Please do not use the inline directive in foo.c files, let the compiler decide.

Thank you.

#16 lore raw
Quoted 11 lines · David Miller

From: Vinod Koul <[email protected]>
Date: Tue, 12 Feb 2019 19:49:22 +0530

Quoted 8 lines
drivers/net/phy/at803x.c +0 -0
index 8ff12938ab47..7b54b54e3316 100644
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
Quoted 15 lines

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 124

Quoted 12 lines
drivers/net/phy/at803x.c +12 -0
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+

Please do not use the inline directive in foo.c files, let the compiler decide.

Isn't the compiler free to ignore the "inline" hint?

Regards.

maintainer
#17 lore raw

From: Marc Gonzalez <[email protected]>
Date: Thu, 14 Feb 2019 17:46:54 +0100

Quoted 29 lines · David Miller
Quoted 12 lines

From: Vinod Koul <[email protected]>
Date: Tue, 12 Feb 2019 19:49:22 +0530

Quoted 8 lines
drivers/net/phy/at803x.c +0 -0
index 8ff12938ab47..7b54b54e3316 100644
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
Quoted 15 lines

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 124

Quoted 12 lines
drivers/net/phy/at803x.c +12 -0
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+

Please do not use the inline directive in foo.c files, let the compiler decide.

Quoted 1 line

Isn't the compiler free to ignore the "inline" hint?

I'm not going into this, but our rules are to not use the inline keyword except in header files where they are required in order to not emit a static copy of the function into every file that includes the header.

author
#18 lore raw
In reply to David Miller
Quoted 11 lines · David Miller

From: Vinod Koul <[email protected]>
Date: Tue, 12 Feb 2019 19:49:22 +0530

Quoted 8 lines
drivers/net/phy/at803x.c +0 -0
index 8ff12938ab47..7b54b54e3316 100644
@@ -110,6 +110,18 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
 	return phy_write(phydev, AT803X_DEBUG_DATA, val);
 }
 
Quoted 15 lines

drivers/net/phy/at803x.c static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, · line 124

Quoted 12 lines
drivers/net/phy/at803x.c +12 -0
+static inline int at803x_enable_rx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
+				     AT803X_DEBUG_RX_CLK_DLY_EN);
+}
+
+static inline int at803x_enable_tx_delay(struct phy_device *phydev)
+{
+	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
+				     AT803X_DEBUG_TX_CLK_DLY_EN);
+}
+

Please do not use the inline directive in foo.c files, let the compiler decide.

Sure, this was in existing code, will fix up current occurrences as well.

Thanks

Signature · 1 line
~Vinod