ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
Subsystems (2)
PATCH 1/1 ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
When I try to boot rk3288-veyron-mickey I totally fail to make the eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_host mmc1: card is non-removable.
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...
When I remove the '/delete-property/mmc-hs200-1_8v' then everything is hunky dory.
That line comes from the original submission of the mickey dts upstream, so presumably at the time the HS200 was failing and just enumerating things as a high speed device was fine. ...or maybe it's just that some mickey devices work when enumerating at "high speed", just not mine?
In any case, hs200 seems good now. Let's turn it on.
---
arch/arm/boot/dts/rk3288-veyron-mickey.dts | 4 ---- 1 file changed, 4 deletions(-)
arch/arm/boot/dts/rk3288-veyron-mickey.dts +0 -4
@@ -128,10 +128,6 @@ }; }; -&emmc { - /delete-property/mmc-hs200-1_8v; -}; - &i2c2 { status = "disabled"; };
Signature · 1 line
2.21.0.1020.gf2820cf01a-goog
Heiko Stuebner
maintainerAm Samstag, 4. Mai 2019, 01:45:37 CEST schrieb Douglas Anderson:
Quoted 32 lines
When I try to boot rk3288-veyron-mickey I totally fail to make the eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_hostmmc1: card is non-removable.
mmc_hostmmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)mmc_hostmmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_hostmmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)mmc_hostmmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...When I remove the '/delete-property/mmc-hs200-1_8v' then everything is hunky dory.
That line comes from the original submission of the mickey dts upstream, so presumably at the time the HS200 was failing and just enumerating things as a high speed device was fine. ...or maybe it's just that some mickey devices work when enumerating at "high speed", just not mine?
Quoted 3 lines
In any case, hs200 seems good now. Let's turn it on.
Signed-off-by Douglas Anderson <[email protected]>
applied for 5.3
Thanks
Heiko