Skip to contentSkip to conversation

wifi: rtw88: 8821cu: Fix firmware upload fail

PATCH In review Bitterblue Smith 4 participants 13 messages Feb 29, 2024 – Mar 29, 2024

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/4 wifi: rtw88: 8821cu: Fix firmware upload fail

RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after reading and writing certain addresses.

Without this, the firmware upload fails approximately more than 50% of the time.

Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU but without Bluetooth.

Fixes a82dfd33d123 ("wifi: rtw88: Add common USB chip support")

---
v2:
- Simplify the code and add comments, as suggested.

---
 drivers/net/wireless/realtek/rtw88/usb.c | 40 ++++++++++++++++++++++++
 1 file changed, 40 insertions(+)
drivers/net/wireless/realtek/rtw88/usb.c +40 -0
index 3c4f28c306a9..3be6cbbf9ad8 100644
@@ -33,6 +33,36 @@ static void rtw_usb_fill_tx_checksum(struct rtw_usb *rtwusb,
 	rtw_tx_fill_txdesc_checksum(rtwdev, &pkt_info, skb->data);
 }
 
+static void rtw_usb_reg_sec(struct rtw_dev *rtwdev, u32 addr, __le32 *data)
+{
+	struct rtw_usb *rtwusb = rtw_get_usb_priv(rtwdev);
+	struct usb_device *udev = rtwusb->udev;
+	bool reg_on_section = false;
+	u16 t_reg = 0x4e0;
+	u8 t_len = 1;
+	int status;
+
+	/* There are three sections:
+	 * 1. on (0x00~0xFF; 0x1000~0x10FF): this section is always powered on
+	 * 2. off (< 0xFE00, excluding "on" section): this section could be
+	 *    powered off
+	 * 3. local (>= 0xFE00): usb specific registers section
+	 */
+	if (addr <= 0xff || (addr >= 0x1000 && addr <= 0x10ff))
+		reg_on_section = true;
+
+	if (!reg_on_section)
+		return;
+
+	status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
+				 RTW_USB_CMD_REQ, RTW_USB_CMD_WRITE,
+				 t_reg, 0, data, t_len, 500);
+
+	if (status != t_len && status != -ENODEV)
+		rtw_err(rtwdev, "%s: reg 0x%x, usb write %u fail, status: %d\n",
+			__func__, t_reg, t_len, status);
+}
+
 static u32 rtw_usb_read(struct rtw_dev *rtwdev, u32 addr, u16 len)
 {
 	struct rtw_usb *rtwusb = rtw_get_usb_priv(rtwdev);
@@ -58,6 +88,11 @@ static u32 rtw_usb_read(struct rtw_dev *rtwdev, u32 addr, u16 len)
 		rtw_err(rtwdev, "read register 0x%x failed with %d\n",
 			addr, ret);
 
+	if (rtwdev->chip->id == RTW_CHIP_TYPE_8822C ||
+	    rtwdev->chip->id == RTW_CHIP_TYPE_8822B ||
+	    rtwdev->chip->id == RTW_CHIP_TYPE_8821C)
+		rtw_usb_reg_sec(rtwdev, addr, data);
+
 	return le32_to_cpu(*data);
 }
 
@@ -111,6 +146,11 @@ static void rtw_usb_write(struct rtw_dev *rtwdev, u32 addr, u32 val, int len)
 	if (ret < 0 && ret != -ENODEV && count++ < 4)
 		rtw_err(rtwdev, "write register 0x%x failed with %d\n",
 			addr, ret);
+
+	if (rtwdev->chip->id == RTW_CHIP_TYPE_8822C ||
+	    rtwdev->chip->id == RTW_CHIP_TYPE_8822B ||
+	    rtwdev->chip->id == RTW_CHIP_TYPE_8821C)
+		rtw_usb_reg_sec(rtwdev, addr, data);
 }
 
 static void rtw_usb_write8(struct rtw_dev *rtwdev, u32 addr, u8 val)
Signature · 1 line
2.43.2
#1 lore raw

PATCH v2 2/4 wifi: rtw88: 8821cu: Fix connection failure

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
	90:55:de:__:__:__ timed out

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

---
v2:
- Check for pwr_on instead of pwr_seq == chip->pwr_on_seq.

---
 drivers/net/wireless/realtek/rtw88/mac.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/net/wireless/realtek/rtw88/mac.c +7 -0
index 298663b03580..0c1c1ff31085 100644
@@ -309,6 +309,13 @@ static int rtw_mac_power_switch(struct rtw_dev *rtwdev, bool pwr_on)
 	pwr_seq = pwr_on ? chip->pwr_on_seq : chip->pwr_off_seq;
 	ret = rtw_pwr_seq_parser(rtwdev, pwr_seq);
 
+	if (pwr_on && rtw_hci_type(rtwdev) == RTW_HCI_TYPE_USB) {
+		if (chip->id == RTW_CHIP_TYPE_8822C ||
+		    chip->id == RTW_CHIP_TYPE_8822B ||
+		    chip->id == RTW_CHIP_TYPE_8821C)
+			rtw_write8_clr(rtwdev, REG_SYS_STATUS1 + 1, BIT(0));
+	}
+
 	if (rtw_hci_type(rtwdev) == RTW_HCI_TYPE_SDIO)
 		rtw_write32(rtwdev, REG_SDIO_HIMR, imr);
 
Signature · 1 line
2.43.2
maintainer Acked-by on v2 2/4
#2 lore raw

RE: [PATCH v2 2/4] wifi: rtw88: 8821cu: Fix connection failure

Quoted 23 lines

-----Original Message-----
From: Bitterblue Smith <[email protected]>
Sent: Friday, March 1, 2024 6:34 AM
To: [email protected]
Cc: Ping-Ke Shih <[email protected]>; Sascha Hauer <[email protected]>
Subject: [PATCH v2 2/4] wifi: rtw88: 8821cu: Fix connection failure

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
        90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
        90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
        90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
        90:55:de:__:__:__ timed out
Quoted 6 lines

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

#3 lore raw

PATCH v2 3/4 wifi: rtw88: 8821c: Fix beacon loss and disconnect

In reply to Bitterblue Smith

Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because of frequent disconnections:

Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
	bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
	- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
	bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
	- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
	bssid=90:55:de:__:__:__ reason=4 locally_generated=1

This is caused by a mistake in the chip initialisation. This version of the chip requires loading an extra AGC table right after the main one, but the extra table is being loaded at the wrong time, in rtw_chip_board_info_setup().

Move the extra AGC table loading to the right place, in rtw_phy_load_tables().

The rtw_chip_board_info_setup() can only do "software" things, and rtw_phy_load_tables() can really do IO.

Fixes 5d6651fe8583 ("rtw88: 8821c: support RFE type2 wifi NIC")

---
v2:
- Add more information in the commit message.

---
 drivers/net/wireless/realtek/rtw88/main.c | 2 --
 drivers/net/wireless/realtek/rtw88/phy.c  | 3 +++
 2 files changed, 3 insertions(+), 2 deletions(-)
drivers/net/wireless/realtek/rtw88/main.c +0 -2
index 6d22628129d0..ffba6b88f392 100644
@@ -2032,8 +2032,6 @@ static int rtw_chip_board_info_setup(struct rtw_dev *rtwdev)
 	rtw_phy_setup_phy_cond(rtwdev, hal->pkg_type);
 
 	rtw_phy_init_tx_power(rtwdev);
-	if (rfe_def->agc_btg_tbl)
-		rtw_load_table(rtwdev, rfe_def->agc_btg_tbl);
 	rtw_load_table(rtwdev, rfe_def->phy_pg_tbl);
 	rtw_load_table(rtwdev, rfe_def->txpwr_lmt_tbl);
 	rtw_phy_tx_power_by_rate_config(hal);
drivers/net/wireless/realtek/rtw88/phy.c +3 -0
index 128e75a81bf3..37ef80c9091d 100644
@@ -1761,12 +1761,15 @@ static void rtw_load_rfk_table(struct rtw_dev *rtwdev)
 
 void rtw_phy_load_tables(struct rtw_dev *rtwdev)
 {
+	const struct rtw_rfe_def *rfe_def = rtw_get_rfe_def(rtwdev);
 	const struct rtw_chip_info *chip = rtwdev->chip;
 	u8 rf_path;
 
 	rtw_load_table(rtwdev, chip->mac_tbl);
 	rtw_load_table(rtwdev, chip->bb_tbl);
 	rtw_load_table(rtwdev, chip->agc_tbl);
+	if (rfe_def->agc_btg_tbl)
+		rtw_load_table(rtwdev, rfe_def->agc_btg_tbl);
 	rtw_load_rfk_table(rtwdev);
 
 	for (rf_path = 0; rf_path < rtwdev->hal.rf_path_num; rf_path++) {
Signature · 1 line
2.43.2
maintainer Acked-by on v2 3/4
#4 lore raw

RE: [PATCH v2 3/4] wifi: rtw88: 8821c: Fix beacon loss and disconnect

Quoted 33 lines

-----Original Message-----
From: Bitterblue Smith <[email protected]>
Sent: Friday, March 1, 2024 6:35 AM
To: [email protected]
Cc: Ping-Ke Shih <[email protected]>; Sascha Hauer <[email protected]>
Subject: [PATCH v2 3/4] wifi: rtw88: 8821c: Fix beacon loss and disconnect

Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because of frequent disconnections:

Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
        bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
        - Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
        bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
        - Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
        bssid=90:55:de:__:__:__ reason=4 locally_generated=1

This is caused by a mistake in the chip initialisation. This version of the chip requires loading an extra AGC table right after the main one, but the extra table is being loaded at the wrong time, in rtw_chip_board_info_setup().

Quoted 8 lines

Move the extra AGC table loading to the right place, in rtw_phy_load_tables().

The rtw_chip_board_info_setup() can only do "software" things, and rtw_phy_load_tables() can really do IO.

Fixes 5d6651fe8583 ("rtw88: 8821c: support RFE type2 wifi NIC")
#5 lore raw

PATCH v2 4/4 wifi: rtw88: 8821c: Fix false alarm count

In reply to Bitterblue Smith

total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just ofdm_fa_cnt.

Fixes 960361238b86 ("rtw88: 8821c: add false alarm statistics")

---
v2:
- No change.

---
 drivers/net/wireless/realtek/rtw88/rtw8821c.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/realtek/rtw88/rtw8821c.c +1 -1
index 429bb420b056..fe5d8e188350 100644
@@ -773,9 +773,9 @@ static void rtw8821c_false_alarm_statistics(struct rtw_dev *rtwdev)
 
 	dm_info->cck_fa_cnt = cck_fa_cnt;
 	dm_info->ofdm_fa_cnt = ofdm_fa_cnt;
+	dm_info->total_fa_cnt = ofdm_fa_cnt;
 	if (cck_enable)
 		dm_info->total_fa_cnt += cck_fa_cnt;
-	dm_info->total_fa_cnt = ofdm_fa_cnt;
 
 	crc32_cnt = rtw_read32(rtwdev, REG_CRC_CCK);
 	dm_info->cck_ok_cnt = FIELD_GET(GENMASK(15, 0), crc32_cnt);
Signature · 1 line
2.43.2
maintainer Acked-by on v2 4/4
#6 lore raw

RE: [PATCH v2 4/4] wifi: rtw88: 8821c: Fix false alarm count

Quoted 9 lines

-----Original Message-----
From: Bitterblue Smith <[email protected]>
Sent: Friday, March 1, 2024 6:36 AM
To: [email protected]
Cc: Ping-Ke Shih <[email protected]>; Sascha Hauer <[email protected]>
Subject: [PATCH v2 4/4] wifi: rtw88: 8821c: Fix false alarm count

Quoted 5 lines

total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just ofdm_fa_cnt.

Fixes 960361238b86 ("rtw88: 8821c: add false alarm statistics")

Thanks for your great work!

maintainer Acked-by on v2 1/4
#7 lore raw
In reply to Bitterblue Smith
Quoted 12 lines

-----Original Message-----
From: Bitterblue Smith <[email protected]>
Sent: Friday, March 1, 2024 6:33 AM
To: [email protected]
Cc: Ping-Ke Shih <[email protected]>; Sascha Hauer <[email protected]>; Sean Mollet <[email protected]>
Subject: [PATCH v2 1/4] wifi: rtw88: 8821cu: Fix firmware upload fail

RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after reading and writing certain addresses.

Quoted 8 lines

Without this, the firmware upload fails approximately more than 50% of the time.

Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU but without Bluetooth.

Fixes a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
#8 lore raw
In reply to Bitterblue Smith
Quoted 6 lines · Bitterblue Smith

RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after reading and writing certain addresses.

Without this, the firmware upload fails approximately more than 50% of the time.

Quoted 6 lines

Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU but without Bluetooth.

Fixes a82dfd33d123 ("wifi: rtw88: Add common USB chip support")

4 patches applied to wireless-next.git, thanks.

41a7acb7dde8 wifi: rtw88: 8821cu: Fix firmware upload fail 605d7c0b05ee wifi: rtw88: 8821cu: Fix connection failure e1dfa21427ba wifi: rtw88: 8821c: Fix beacon loss and disconnect c238adbc578e wifi: rtw88: 8821c: Fix false alarm count

Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
#9 lore raw

PATCH 1/1 wifi: rtw88: 8821cu: Fix connection failure

In reply to Bitterblue Smith

From: Bitterblue Smith <[email protected]>

[ Upstream commit 605d7c0b05eecb985273b1647070497142c470d3 ]

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
	90:55:de:__:__:__ timed out

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

---
 drivers/net/wireless/realtek/rtw88/mac.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/net/wireless/realtek/rtw88/mac.c +7 -0
index 298663b03580..0c1c1ff31085 100644
@@ -309,6 +309,13 @@ static int rtw_mac_power_switch(struct rtw_dev *rtwdev, bool pwr_on)
 	pwr_seq = pwr_on ? chip->pwr_on_seq : chip->pwr_off_seq;
 	ret = rtw_pwr_seq_parser(rtwdev, pwr_seq);
 
+	if (pwr_on && rtw_hci_type(rtwdev) == RTW_HCI_TYPE_USB) {
+		if (chip->id == RTW_CHIP_TYPE_8822C ||
+		    chip->id == RTW_CHIP_TYPE_8822B ||
+		    chip->id == RTW_CHIP_TYPE_8821C)
+			rtw_write8_clr(rtwdev, REG_SYS_STATUS1 + 1, BIT(0));
+	}
+
 	if (rtw_hci_type(rtwdev) == RTW_HCI_TYPE_SDIO)
 		rtw_write32(rtwdev, REG_SDIO_HIMR, imr);
 
Signature · 1 line
2.43.2
maintainer
#10 lore raw

Re: [PATCH] wifi: rtw88: 8821cu: Fix connection failure

Quoted 23 lines · Bitterblue Smith

From: Bitterblue Smith <[email protected]>

[ Upstream commit 605d7c0b05eecb985273b1647070497142c470d3 ]

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
	90:55:de:__:__:__ timed out

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

Quoted 7 lines
---
 drivers/net/wireless/realtek/rtw88/mac.c | 7 +++++++
 1 file changed, 7 insertions(+)

What stable kernel(s) is this to be applied to?

thanks,

greg k-h

#11 lore raw

Re: [PATCH] wifi: rtw88: 8821cu: Fix connection failure

Quoted 32 lines · Greg KH
Quoted 23 lines · Bitterblue Smith

From: Bitterblue Smith <[email protected]>

[ Upstream commit 605d7c0b05eecb985273b1647070497142c470d3 ]

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
	90:55:de:__:__:__ timed out

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

Quoted 7 lines
---
 drivers/net/wireless/realtek/rtw88/mac.c | 7 +++++++
 1 file changed, 7 insertions(+)
Quoted 5 lines

What stable kernel(s) is this to be applied to?

thanks,

greg k-h

6.6, 6.7, and 6.8, please. The older ones don't have USB support in rtw88.

Thank you.

maintainer
#12 lore raw

Re: [PATCH] wifi: rtw88: 8821cu: Fix connection failure

Quoted 33 lines · Bitterblue Smith
Quoted 32 lines · Greg KH
Quoted 30 lines · Bitterblue Smith

From: Bitterblue Smith <[email protected]>

[ Upstream commit 605d7c0b05eecb985273b1647070497142c470d3 ]

Clear bit 8 of REG_SYS_STATUS1 after MAC power on.

Without this, some RTL8821CU and RTL8811CU cannot connect to any network:

Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
	90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
	90:55:de:__:__:__ timed out

The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips.

Tested with RTL8811CU (Tenda U9 V2.0).

---
 drivers/net/wireless/realtek/rtw88/mac.c | 7 +++++++
 1 file changed, 7 insertions(+)
Quoted 8 lines
Quoted 5 lines

What stable kernel(s) is this to be applied to?

thanks,

greg k-h

6.6, 6.7, and 6.8, please. The older ones don't have USB support in rtw88.

Now queued up, thanks.

greg k-h