ethernet on FCC
Hi,
My mpc8270 board use three ehternet ports at FCC1,FCC2,FCC3.it is
work well at FCC1.When I use port FCC2, I found out the
u-boot is not receiving packets (It's sending correct packet when i
use ethereal for sniffing). When trying "ping", it generated an ARP
packet first, the other host replied with , but the board never seems
to receive it(set printf at function fec_recv() /cpu/mpc8260/ether_fcc.c ).all three ethernet fcc ports initiailze is same.Do I miss something?thank you for your suggestion,my config file config FCC port parameter as follow:
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_NET_MULTI
#define CONFIG_ETHER_ON_FCC1
#define CONFIG_ETHER_ON_FCC2
#define CONFIG_ETHER_ON_FCC3
#define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK13 | CMXFCR_TF3CS_CLK14)
#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
#define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK15 | CMXFCR_TF2CS_CLK16)
#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
#define CFG_RX_ETH_BUFFER 128 #define CONFIG_IPADDR 192.168.10.17 #define CONFIG_SERVERIP 192.168.10.101 #define CONFIG_HOSTNAME OceanSCC #define CONFIG_LOADADDR 1000 /* default location for tftp and bootm */
#define CONFIG_BOOTFILE u-boot.bin
#define CONFIG_ETHADDR 00:13:09:11:22:33
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:13:09:04:05:36
#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:13:09:07:08:39
#define CONFIG_EXTRA_ENV_SETTINGS "ethprime=FCC1 ETHERNET"
#define CFG_CPMFCR_RAMTYPE 0 /* BDs and buffers on 60x bus */
#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) /* Full duplex */
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
Sincerely,
Jie
---------------------------------
Don't pick lemons.
See all the new 2007 cars at Yahoo! Autos.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20070204/c5032971/attachment.htm
Quoted 50 lines · jie han
Hi,
My mpc8270 board use three ehternet ports at FCC1,FCC2,FCC3.it is work well at FCC1.When I use port FCC2, I found out the u-boot is not receiving packets (It's sending correct packet when i use ethereal for sniffing). When trying "ping", it generated an ARP packet first, the other host replied with , but the board never seems to receiveit(set printf at function fec_recv() /cpu/mpc8260/ether_fcc.c ).all three ethernet fcc ports initiailze is same.Do I miss something?thank you for your suggestion,my config file config FCC port parameter as follow:#undef
CONFIG_ETHER_ON_SCC/* define if ether on SCC */
#defineCONFIG_ETHER_ON_FCC/* define if ether on FCC */
#undefCONFIG_ETHER_NONE/* define if ether on something else */
#defineCONFIG_NET_MULTI
#defineCONFIG_ETHER_ON_FCC1
#defineCONFIG_ETHER_ON_FCC2
#defineCONFIG_ETHER_ON_FCC3#define
CFG_CMXFCR_VALUE1(CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
#defineCFG_CMXFCR_MASK1(CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)#define
CFG_CMXFCR_VALUE3(CMXFCR_RF3CS_CLK13|CMXFCR_TF3CS_CLK14)
#defineCFG_CMXFCR_MASK3(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)#define
CFG_CMXFCR_VALUE2(CMXFCR_RF2CS_CLK15|CMXFCR_TF2CS_CLK16)
#defineCFG_CMXFCR_MASK2(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)#define CFG_RX_ETH_BUFFER 128 #define CONFIG_IPADDR 192.168.10.17 #define CONFIG_SERVERIP 192.168.10.101 #define CONFIG_HOSTNAME OceanSCC #define CONFIG_LOADADDR 1000 /* default location for tftp andbootm */
#defineCONFIG_BOOTFILEu-boot.bin#define
CONFIG_ETHADDR00:13:09:11:22:33
#defineCONFIG_HAS_ETH1
#defineCONFIG_ETH1ADDR00:13:09:04:05:36
#defineCONFIG_HAS_ETH2
#defineCONFIG_ETH2ADDR00:13:09:07:08:39#define
CONFIG_EXTRA_ENV_SETTINGS"ethprime=FCC1 ETHERNET"#define
CFG_CPMFCR_RAMTYPE0 /* BDs and buffers on 60x bus */
#defineCFG_FCC_PSMR(FCC_PSMR_FDE|FCC_PSMR_LPB) /* Full duplex */
Quoted 6 lines
#define
CONFIG_MII/* MII PHY management */
#defineCONFIG_BITBANGMII/* bit-bang MII PHY management */Sincerely,
Jie
Hi Jie,
I don't have any good insights, but some things to try:
* Are you sure, positive, double checked and had a co-worker check that your clock input for FCC2-Rx is configured properly?
1) Which CLK input is used?
2) The port/pin configuration initialization in u-boot?
3) Your hardware (traces) actually connect the right pins?
* Does FCC3 work?
* If you turn off CONFIG_NET_MULTI and only use FCC2, does it work?
* If you turn off CONFIG_NET_MULTI and only use FCC3, does it work?
Good luck,
gvb
Thank you for your help.The fcc2 working now,It is my mistake to config fcc2 RX_DV port pin.
Sincerely,
Jie
Quoted 50 lines · Jerry Van Baren <[email protected]> wrote: jie han wrote:
Hi,
My mpc8270 board use three ehternet ports at FCC1,FCC2,FCC3.it is work well at FCC1.When I use port FCC2, I found out the u-boot is not receiving packets (It's sending correct packet when i use ethereal for sniffing). When trying "ping", it generated an ARP packet first, the other host replied with , but the board never seems to receiveit(set printf at function fec_recv() /cpu/mpc8260/ether_fcc.c ).all three ethernet fcc ports initiailze is same.Do I miss something?thank you for your suggestion,my config file config FCC port parameter as follow:#undef
CONFIG_ETHER_ON_SCC/* define if ether on SCC */
#defineCONFIG_ETHER_ON_FCC/* define if ether on FCC */
#undefCONFIG_ETHER_NONE/* define if ether on something else */
#defineCONFIG_NET_MULTI
#defineCONFIG_ETHER_ON_FCC1
#defineCONFIG_ETHER_ON_FCC2
#defineCONFIG_ETHER_ON_FCC3#define
CFG_CMXFCR_VALUE1(CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
#defineCFG_CMXFCR_MASK1(CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)#define
CFG_CMXFCR_VALUE3(CMXFCR_RF3CS_CLK13|CMXFCR_TF3CS_CLK14)
#defineCFG_CMXFCR_MASK3(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)#define
CFG_CMXFCR_VALUE2(CMXFCR_RF2CS_CLK15|CMXFCR_TF2CS_CLK16)
#defineCFG_CMXFCR_MASK2(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)#define CFG_RX_ETH_BUFFER 128 #define CONFIG_IPADDR 192.168.10.17 #define CONFIG_SERVERIP 192.168.10.101 #define CONFIG_HOSTNAME OceanSCC #define CONFIG_LOADADDR 1000 /* default location for tftp andbootm */
#defineCONFIG_BOOTFILEu-boot.bin#define
CONFIG_ETHADDR00:13:09:11:22:33
#defineCONFIG_HAS_ETH1
#defineCONFIG_ETH1ADDR00:13:09:04:05:36
#defineCONFIG_HAS_ETH2
#defineCONFIG_ETH2ADDR00:13:09:07:08:39#define
CONFIG_EXTRA_ENV_SETTINGS"ethprime=FCC1 ETHERNET"#define
CFG_CPMFCR_RAMTYPE0 /* BDs and buffers on 60x bus */
#defineCFG_FCC_PSMR(FCC_PSMR_FDE|FCC_PSMR_LPB) /* Full duplex */
Quoted 6 lines
#define
CONFIG_MII/* MII PHY management */
#defineCONFIG_BITBANGMII/* bit-bang MII PHY management */Sincerely,
Jie
Hi Jie,
I don't have any good insights, but some things to try:
* Are you sure, positive, double checked and had a co-worker check that your clock input for FCC2-Rx is configured properly?
1) Which CLK input is used?
2) The port/pin configuration initialization in u-boot?
3) Your hardware (traces) actually connect the right pins?
* Does FCC3 work?
* If you turn off CONFIG_NET_MULTI and only use FCC2, does it work?
* If you turn off CONFIG_NET_MULTI and only use FCC3, does it work?
Good luck,
gvb
---------------------------------
Bored stiff? Loosen up...
Download and play hundreds of games for free on Yahoo! Games. -------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20070208/58e64434/attachment.htm