Skip to contentSkip to conversation

Request: examples of using LILO or GRUB to boot from DOC

DISCUSSION Christian Lademann 3 participants 4 messages Jul 26, 2000 – Jul 27, 2000 Memory technology devices (MTD)

lore
Share & tools
lore
#0 lore raw

I am trying hard to get a 4Mb DoC to boot something else but MS-DOS. Could somebody please mail me her/his lilo-
or grub-configuration?
Is there currently a working way to boot Linux from a DOC using free software, anyhow?

cu, Christian.

--

*  Christian A. Lademann, ZLS Software GmbH               mailto:[email protected]
*  ZLS Software GmbH
*  Frankfurter Strasse 59       Postfach 1628             mailto:[email protected]
*  D-65779 Kelkheim             D-65766 Kelkheim          http://www.zls.de
*  Telefon +49-6195-9902-0      Telefax +49-6195-900600
*  Geschäftsführer John A. Shuter     -     Amtsgericht Königstein HRB 3105

To unsubscribe, send "unsubscribe mtd" to [email protected]

#1 lore raw
Quoted 6 lines · Christian Lademann

I am trying hard to get a 4Mb DoC to boot something else but MS-DOS. Could somebody please mail me her/his lilo-
or grub-configuration?
Is there currently a working way to boot Linux from a DOC using free software, anyhow?

lilo works, use the patched one from the mtd package.
for a stable system it is recomended to use the DoC driver provided by m-system, i guess.

Installation goes like this:

- mount the DoC to /mnt/doc.
- put a kernel with according driver in /mnt/doc/boot/, name it kernel;
- copy the boot.b from the mtd package to /mnt/doc/boot/
- change the rootdevice of the kernel with 'rdev /dev/fla1 /mnt/doc/boot/kernel'

- Generate /root/lilo-doc.conf similar to the following:

boot=/dev/fla
vga = normal
read-only
prompt
timeout=50
image = /mnt/doc/boot/kernel
root = /dev/fla1
label = linux

- install lilo with
lilo-mtd -C /root/lilo-doc.conf -I /mnt/doc/boot/boot.b -m
/mnt/doc/boot/map

-reboot

Note:
dunno about a small DoC, but on a 16mb you will need a extra boot partition with ie. 1MB,
because otherwise lilo will see too much cylinders (>1024) and therefore can't be installed.
if you do this, surely change /dev/fla1 to /dev/fla2, because /dev/fla1 just holds the kernel.

Signature · 14 lines
Best regards, Karl Pitrich. icq #81091001

pitrich information technologies
linuxsoftwareinternetworkcommunication!
hauptstraße 16-18 | 4040 linz | austria 
voice: +43 70 718884 | support: 0900 970 710 (.at only)
--
 Microsoft is prohibited from distributing this work in any form, in
 whole or in part, across any medium. Licenses for distribution are 
 available to Microsoft for $500. Posting without permission constitutes
 an agreement to these terms.


To unsubscribe, send "unsubscribe mtd" to [email protected]
#2 lore raw

Karl Pitrich writes ("Re: Request: examples of using LILO or GRUB to boot from DOC"):

Quoted 10 lines

- Generate /root/lilo-doc.conf similar to the following:

boot=/dev/fla
vga = normal
read-only
prompt
timeout=50
image = /mnt/doc/boot/kernel
root = /dev/fla1
label = linux

You might also want to add a boot = /mnt/doc/boot/boot, and map = /mnt/doc/boot/map instead of passing them in the command line.

One important thing to remember is that you MUST pass these parameters from the mounted flash, and not from copies in your hard disk, otherwise LILO won't work.

Signature · 7 lines
Dvir Oren               <[email protected]>
Lucid VON Ltd.     <http://www.lucidvon.com>
9 Saloniki St.,        Tel-Aviv       Israel
Tel:  +972 3 644 3038  Fax:  +972 3 644 3039


To unsubscribe, send "unsubscribe mtd" to [email protected]
#3 lore raw
In reply to Karl Pitrich

Thank you for your helping hand. It worked with the "DOC123.EXB"-firmware

installed and the /dev/nftla1 being the FAT12-fs created by dformat.

Repartitioning the nftla worked as well but no success booting anymore.

Using the M-Systems-driver, /dev/fla* and plilo repartitioning and

booting works well.

cu, Christian.

PS: where do I find a 'as86' that is able to compile lilo? The current

bin86-release found on metalab.unc.edu does not do the job.

--

*  Christian A. Lademann, ZLS Software GmbH               mailto:[email protected]
*  ZLS Software GmbH
*  Frankfurter Strasse 59       Postfach 1628             mailto:[email protected]
*  D-65779 Kelkheim             D-65766 Kelkheim          http://www.zls.de
*  Telefon +49-6195-9902-0      Telefax +49-6195-900600
*  Geschäftsführer John A. Shuter     -     Amtsgericht Königstein HRB 3105

To unsubscribe, send "unsubscribe mtd" to [email protected]