Discover current address mode by CRC
Subsystems (4)
cover Discover current address mode by CRC
From: Takahiro Kuwano <[email protected]>
Hello,
I introduced this series based on the discussion [0].
Patch#1 is needed to use READ_4B(13h) for offline CRC calculation. This can replace spi_nor_read_raw() in SFDP, if it is OK.
Path#2 implements address mode discovery by:
- determine factory default from BFPT DWORD16
- read 4 bytes from address 0 by 13h opcode
- calculate CRC from 4 byte data by offline
- perform data integrity CRC op
- read data integrity CRC register by Read Any Reg with 3- and/or 4-byte address bytes to determine the current address mode
Takahiro Kuwano (2):
mtd: spi-nor: core: Add a helper to read with alternative method
mtd: spi-nor: spansion: Discover current address mode by CRC
drivers/mtd/spi-nor/core.c | 48 ++++++++++++ drivers/mtd/spi-nor/core.h | 2 + drivers/mtd/spi-nor/sfdp.h | 1 + drivers/mtd/spi-nor/spansion.c | 130 +++++++++++++++++++++++++++++++++ 4 files changed, 181 insertions(+)
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH 1/2 mtd: spi-nor: core: Add a helper to read with alternative method
From: Takahiro Kuwano <[email protected]>
The existing spi_nor_read_data() uses preset opcode, number of address bytes, and dummy cycles. During SFDP parse and corresponding fixups we need to perform read op with different opcode, number of address, and/or dummy cycles from preset ones. The spi_nor_alt_read() helps that by backup - read op - restore the preset opcode, etc.
--- drivers/mtd/spi-nor/core.c | 48 ++++++++++++++++++++++++++++++++++++++ drivers/mtd/spi-nor/core.h | 2 ++ 2 files changed, 50 insertions(+)
drivers/mtd/spi-nor/core.c +48 -0
@@ -247,6 +247,54 @@ ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len, u8 *buf)return nor->controller_ops->read (nor, from, len, buf); } +/** +* spi_nor_alt_read() - read data from flash memory with alternative opcode, +* number of address bytes, and dummy cycles. +* @nor: pointer to 'struct spi_nor' +* @from: offset to read from +* @len: number of bytes to read +* @buf: pointer to dst buffer +* @read_opcode: read opcode to issue +* @addr_nbytes: number of address bytes to send +* @read_dummy: number of dummy cycles needed to read +* +* Return: 0 on success, -errno otherwise +*/ +int spi_nor_alt_read (struct spi_nor *nor,u32 addr,size_t len,u8 *buf, +u8 read_opcode,u8 addr_nbytes,u8 read_dummy) +{ +u8 bak_read_opcode = nor->read_opcode; +u8 bak_addr_nbytes = nor->addr_nbytes; +u8 bak_read_dummy = nor->read_dummy; +ssize_t ret; + + nor->read_opcode = read_opcode; + nor->addr_nbytes = addr_nbytes; + nor->read_dummy = read_dummy; + +while (len) { + ret =spi_nor_read_data (nor, addr, len, buf); +if (ret <0 ) + goto out; +if (!ret || ret > len) { + ret = -EIO ; + goto out; + } + + buf += ret; + addr += ret; + len -= ret; + } + ret =0 ; + +out: + nor->read_opcode = bak_read_opcode; + nor->addr_nbytes = bak_addr_nbytes; + nor->read_dummy = bak_read_dummy; + +return ret; +} +/** * spi_nor_spimem_write_data() - write data to flash memory via * spi-mem
drivers/mtd/spi-nor/core.h +2 -0
@@ -656,6 +656,8 @@ ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len, u8 *buf);ssize_t spi_nor_write_data (struct spi_nor *nor,loff_t to,size_t len,const u8 *buf); +int spi_nor_alt_read (struct spi_nor *nor,u32 addr,size_t len,u8 *buf, +u8 read_opcode,u8 addr_nbytes,u8 read_dummy);int spi_nor_read_any_reg (struct spi_nor *nor,struct spi_mem_op *op,enum spi_nor_protocol proto); int spi_nor_write_any_volatile_reg(struct spi_nor *nor, struct spi_mem_op *op,
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH 2/2 mtd: spi-nor: spansion: Discover current address mode by CRC
In reply to [email protected]From: Takahiro Kuwano <[email protected]>
In some Infineon devices, the address mode (3- or 4-byte) is configurable in both volatile and non-volatile registers. Determining current address mode prior to SMPT parse is crucial because Read Any Reg op used in SMPT takes 3- or 4-byte address depending on current address mode. The current address mode is found in CFR2V[7] but CFR2V can be read by Read Any Reg op (chicken-and-egg). This patch introduce a way to discover the current address mode by using on-die CRC feature in Infineon SEMPER family.
The data integrity CRC (on-die CRC) calculation is conducted by issuing a specific command followed by start and end addresses on which CRC is calculated. The flash becomes busy state during calculation so we need to poll status and wait for the completion. The calculated CRC value is stored in Data Integrity Check CRC registers (DCRV) and can be read by Read Any Reg op. We can try with 3- and 4-byte addresses to read DCRV then compare it with expected CRC value calculated by offline. Both CRC should match only when we perform Read Any Reg op with correct number of address bytes.
The offline CRC calculation is done by CRC32C algorithm with 0x1edc6f41 polynomial. The data is read by READ_4B (13h) opcode.
BFPT DWORD16 is used to determine factory default of address mode, assuming factory default is 3-byte in case power cycle exits 4-byte address mode.
--- drivers/mtd/spi-nor/sfdp.h | 1 + drivers/mtd/spi-nor/spansion.c | 130 +++++++++++++++++++++++++++++++++ 2 files changed, 131 insertions(+)
drivers/mtd/spi-nor/sfdp.h +1 -0
@@ -90,6 +90,7 @@ struct sfdp_bfpt {#define BFPT_DWORD15_QER_SR2_BIT1_NO_RD (0x4UL << 20)#define BFPT_DWORD15_QER_SR2_BIT1 (0x5UL << 20)/* Spansion */ +#define BFPT_DWORD16_EX4B_PWRCYC BIT(21)#define BFPT_DWORD16_SWRST_EN_RST BIT(12)#define BFPT_DWORD18_CMD_EXT_MASK GENMASK(30, 29)
drivers/mtd/spi-nor/spansion.c +130 -0
148 lines not on this page · raw message
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH 2/2] mtd: spi-nor: spansion: Discover current address mode by CRC
Hi, Takahiro,
Quoted 5 lines · On 8/12/22 11:06, [email protected] wrote:
drivers/mtd/spi-nor/spansion.c +5
-0+#define CRC32C_POLY 0x1edc6f41 +static u32 cypress_nor_calc_crc32c (u32 len,u8 *buf) +{ +u32 crc =0 ; +int i;
drivers/mtd/spi-nor/spansion.c static int cypress_nor_set_page_size(struct spi_nor *nor) · line 232
Quoted 10 lines
drivers/mtd/spi-nor/spansion.c +10
-0+ +while (len--) { + crc ^= *buf++ <<24 ; +for (i =0 ; i <8 ; i++) + crc = (crc <<1 ) ^ ((crc &0x80000000 ) ?CRC32C_POLY : +0 ); + } + +return crc; +}
I haven't gone through the details of the patch set, but I like the idea. I stumbled on your crc implementation. Can't we use #include <linux/crc32.h> instead?
Signature · 5 lines
Cheers, ta ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH 2/2] mtd: spi-nor: spansion: Discover current address mode by CRC
Quoted 14 lines · On 10/5/2022 4:10 PM, [email protected] wrote:
Hi, Takahiro,
Quoted 11 lines · On 8/12/22 11:06, [email protected] wrote:
(quoted diff) +11
-0+#define CRC32C_POLY 0x1edc6f41 +static u32 cypress_nor_calc_crc32c(u32 len, u8 *buf) +{ + u32 crc = 0; + int i; + + while (len--) { + crc ^= *buf++ << 24; + for (i = 0; i < 8; i++) + crc = (crc << 1) ^ ((crc & 0x80000000) ? CRC32C_POLY : + 0);
Quoted 9 lines
Review
Quoted 4 lines
(quoted diff) +4
-0+ } + + return crc; +}I haven't gone through the details of the patch set, but I like the idea. I stumbled on your crc implementation. Can't we use #include <
linux/crc32.h> instead?
CRC32C BE is a missing piece in lib/crc32 so I added this local helper.
I have created following patch that adds CRC32C BE into lib/crc32. Do you agree to submit this?
We also need to add test case to crc32test.c.
include/linux/crc32.h +1 -0
@@ -37,6 +37,7 @@ static inline u32 crc32_le_combine(u32 crc1, u32 crc2, size_t len2) }u32 __pure __crc32c_le (u32 crc,unsigned char const *p,size_t len); +u32 __pure __crc32c_be (u32 crc,unsigned char const *p,size_t len);/** * __crc32c_le_combine - Combine two crc32c check values into one. For two
include/linux/crc32poly.h +1 -0
@@ -16,5 +16,6 @@* x^8+x^6+x^0 */ #define CRC32C_POLY_LE 0x82F63B78 +#define CRC32C_POLY_BE 0x1EDC6F41#endif /* _LINUX_CRC32_POLY_H */
lib/crc32.c +9 -0
@@ -335,10 +335,19 @@ u32 __pure __weak crc32_be(u32 crc, unsigned char const *p, size_t len) {return crc32_be_generic (crc, p, len,NULL ,CRC32_POLY_BE ); } +u32 __pure __weak __crc32c_be (u32 crc,unsigned char const *p,size_t len) +{ +return crc32_be_generic (crc, p, len,NULL ,CRC32C_POLY_BE ); +}#else u32 __pure __weak crc32_be (u32 crc,unsigned char const *p,size_t len) {return crc32_be_generic (crc, p, len, crc32table_be,CRC32_POLY_BE ); } +u32 __pure __weak __crc32c_be (u32 crc,unsigned char const *p,size_t len) +{ +return crc32_be_generic (crc, p, len, crc32ctable_be,CRC32C_POLY_BE ); +}#endif EXPORT_SYMBOL (crc32_be); +EXPORT_SYMBOL (__crc32c_be);
lib/gen_crc32table.c +29 -8
@@ -26,6 +26,7 @@static uint32_t crc32table_le[LE_TABLE_ROWS ][256 ];static uint32_t crc32table_be[BE_TABLE_ROWS ][256 ];static uint32_t crc32ctable_le[LE_TABLE_ROWS ][256 ]; +static uint32_t crc32ctable_be[BE_TABLE_ROWS ][256 ];/** * crc32init_le() - allocate and initialize LE table data
@@ -67,29 +68,40 @@ static void crc32cinit_le(void) }/** -* crc32init_be() - allocate and initialize BE table data +* crc32init_be_generic() - allocate and initialize BE table data */ -static void crc32init_be (void ) +static void crc32init_be_generic (const uint32_t polynomial, +uint32_t (*tab)[256 ]) {unsigned i, j;uint32_t crc =0x80000000 ; - crc32table_be[0 ][0 ] =0 ; + tab[0 ][0 ] =0 ;for (i =1 ; i <BE_TABLE_SIZE ; i <<=1 ) { - crc = (crc <<1 ) ^ ((crc &0x80000000 ) ?CRC32_POLY_BE :0 ); + crc = (crc <<1 ) ^ ((crc &0x80000000 ) ? polynomial :0 );for (j =0 ; j < i; j++) - crc32table_be[0 ][i + j] = crc ^ crc32table_be[0 ][j]; + tab[0 ][i + j] = crc ^ tab[0 ][j]; }for (i =0 ; i <BE_TABLE_SIZE ; i++) { - crc = crc32table_be[0 ][i]; + crc = tab[0 ][i];for (j =1 ; j <BE_TABLE_ROWS ; j++) { - crc = crc32table_be[0 ][(crc >>24 ) &0xff ] ^ (crc <<8 ); - crc32table_be[j][i] = crc; + crc = tab[0 ][(crc >>24 ) &0xff ] ^ (crc <<8 ); + tab[j][i] = crc; } } } +static void crc32init_be (void ) +{ +crc32init_be_generic (CRC32_POLY_BE , crc32table_be); +} + +static void crc32cinit_be (void ) +{ +crc32init_be_generic (CRC32C_POLY_BE , crc32ctable_be); +} +static void output_table (uint32_t (*table)[256 ],int rows,int len,char *trans) {int i, j;
@@ -137,6 +149,15 @@ int main(int argc, char** argv) LE_TABLE_SIZE, "tole");printf ("};\n" ); } +if (CRC_BE_BITS >1 ) { +crc32cinit_be (); +printf ("static const u32 ____cacheline_aligned " +"crc32ctable_be[%d][%d] = {" , +BE_TABLE_ROWS ,BE_TABLE_SIZE ); +output_table (crc32ctable_be,BE_TABLE_ROWS , +BE_TABLE_SIZE ,"tobe" ); +printf ("};\n" ); + }return 0 ; }
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Hi Tudor,
Have you had a chance to take a look?
Thanks,
Takahiro
Quoted 23 lines · On 8/12/2022 5:06 PM, [email protected] wrote:
From: Takahiro Kuwano <[email protected]>
Hello,
I introduced this series based on the discussion [0].
Patch#1 is needed to use
READ_4B(13h)for offline CRC calculation. This can replacespi_nor_read_raw()in SFDP, if it is OK.Path#2 implements address mode discovery by:
- determine factory default from BFPT DWORD16
- read 4 bytes from address 0 by 13h opcode
- calculate CRC from 4 byte data by offline
- perform data integrity CRC op
- read data integrity CRC register by Read Any Reg with 3- and/or 4-byte address bytes to determine the current address modeTakahiro Kuwano (2):
mtd: spi-nor: core: Add a helper to read with alternative method
mtd: spi-nor: spansion: Discover current address mode by CRC
Quoted 6 lines
drivers/mtd/spi-nor/core.c | 48 ++++++++++++ drivers/mtd/spi-nor/core.h | 2 + drivers/mtd/spi-nor/sfdp.h | 1 + drivers/mtd/spi-nor/spansion.c | 130 +++++++++++++++++++++++++++++++++ 4 files changed, 181 insertions(+)
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/