Fasttrak 100 configuration

So I'm trying to get the Promise Fasttrack 100 driver included with 2.4.0-test10 to work on my system.
I have 2 45GB drives hooked up in RAID0.

I'm trying to install directly onto the drives, but I'm having a couple problems.
It seems to detect the controller card and the drives, but they are not assigned to any devices.

Any suggestions?
Thanks,
--James Lamanna

Here is some info:
dmesg:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20265: IDE controller on PCI bus 00 dev 88
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode.
PDC20265: FORCING BURST BIT 0x00 -> 0x01 ACTIVE

    ide0: BM-DMA at 0x6400-0x6407, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x6408-0x640f, BIOS settings: hdc:DMA, hdd:pio

PDC20267: IDE controller on PCI bus 00 dev 58
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode.
PDC20267: neither IDE port enabled (BIOS)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This line is interesting I thought...

/proc/pci:
Bus 0, device 11, function 0:

    RAID bus controller: Promise Technology, Inc. 20267 (rev 2).
      IRQ 10.
      Master Capable.  Latency=32.
      I/O at 0x9400 [0x9407].
      I/O at 0x9000 [0x9003].
      I/O at 0x8800 [0x8807].
      I/O at 0x8400 [0x8403].
      I/O at 0x8000 [0x803f].
      Non-prefetchable 32 bit memory at 0xd5000000 [0xd501ffff].
  Bus  0, device  17, function  0:
    Unknown mass storage controller: Promise Technology, Inc. 20265 (rev
2).
      IRQ 10.
      Master Capable.  Latency=32.
      I/O at 0x7800 [0x7807].
      I/O at 0x7400 [0x7403].
      I/O at 0x7000 [0x7007].
      I/O at 0x6800 [0x6803].
      I/O at 0x6400 [0x643f].
      Non-prefetchable 32 bit memory at 0xd4800000 [0xd481ffff].

/proc/ide/pdc202xx:

                                PDC20265 Chipset.
------------------------------- General Status 
Burst Mode                           : enabled
Host Mode                            : Normal
Bus Clocking                         : 33 PCI Internal
IO pad select                        : 10 mA
Status Polling Period                : 5

Interrupt Check Status Polling Delay : 7 --------------- Primary Channel ---------------- Secondary Channel
-------------
enabled enabled
66 Clocking disabled disabled
Mode PCI Mode PCI
FIFO Empty FIFO Empty
--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------

DMA enabled:    no               no              yes               no
DMA Mode:       NOTSET           NOTSET          NOTSET           

NOTSET
PIO Mode: NOTSET NOTSET NOTSET
NOTSET
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
Please read the FAQ at http://www.tux.org/lkml/