Skip to contentSkip to conversation

IDE trouble under 2.2.19pre16 with Hedrick's IDE patch

DISCUSSION Shane Wegner 3 participants 3 messages Mar 5, 2001 – Mar 6, 2001

lore
Share & tools
lore
#0 lore raw

Hi,

Whenever I write a substantial amount of data (200mb) to disk, I get these messages. The disks lock for about 10 seconds and then come back for about 10 seconds again. This continues until the data is successfully written.

ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hde: DMA disabled
hde: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hde: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hde: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }

Does anyone happen to know what I can do to fix this? It happens on Linux 2.4.2 as well. It's an HPT370 controler on-board. Here is the relevant information.

HPT370: IDE controller on PCI bus 00 dev 70
HPT370: chipset revision 3
HPT370: not 100% native mode: will probe irqs later

    ide2: BM-DMA at 0xec00-0xec07, BIOS settings: hde:DMA,
hdf:pio
    ide3: BM-DMA at 0xec08-0xec0f, BIOS settings: hdg:DMA,

hdh:pio
hde: Maxtor 92720U8, ATA DISK drive
hdg: Maxtor 96147U8, ATA DISK drive
ide2 at 0xdc00-0xdc07,0xe002 on irq 10
ide3 at 0xe400-0xe407,0xe802 on irq 10
hde: Maxtor 92720U8, 25965MB w/2048kB Cache,
CHS=52755/16/63, UDMA(66)
hdg: Maxtor 96147U8, 58623MB w/2048kB Cache,
CHS=119108/16/63, UDMA(66)

continuum:~# cat /proc/ide/hpt366
                                HPT370 Chipset.

--------------- Primary Channel ---------------- Secondary Channel -------------
enabled enabled
--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------
DMA enabled: yes no yes
no
UDMA
DMA
PIO

continuum:~# cat /proc/ide/hde/settings
name                    value           min             max
mode
----                    -----           ---             ---
----
bios_cyl                52755           0
65535           rw
bios_head               16              0               255
rw
bios_sect               63              0               63
rw
breada_readahead        4               0               127
rw
bswap                   0               0               1
r
current_speed           68              0               69
rw
file_readahead          124             0
2097151         rw
ide_scsi                0               0               1
rw
init_speed              68              0               69
rw
io_32bit                1               0               3
rw
keepsettings            1               0               1
rw
lun                     0               0               7
rw
max_kb_per_request      64              1               127
rw
multcount               8               0               8
rw
nice1                   1               0               1
rw
nowerr                  0               0               1
rw
number                  0               0               3
rw
pio_mode                write-only      0               255
w
slow                    0               0               1
rw
unmaskirq               1               0               1
rw
using_dma               1               0               1
rw
Signature · 5 lines
Shane Wegner: [email protected]
              http://www.cm.nu/~shane/
PGP:          1024D/FFE3035D
              A0ED DAC4 77EC D674 5487
              5B5C 4F89 9A4E FFE3 035D
#1 lore raw
Quoted 11 lines · Shane Wegner

Hi,

Whenever I write a substantial amount of data (200mb) to disk, I get these messages. The disks lock for about 10 seconds and then come back for about 10 seconds again. This continues until the data is successfully written.

ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hde: DMA disabled

It looks like you have set your drive for a dma mode it doesn't support.

HTH

Mike

#2 lore raw

No this error is not by the wrong DMA settings. If you have a drive in dma mode 5 and the controller does not support it, the kernel will give you a proper error saying that this dma mode is not supported by the controller. This is most likly something with the kernel. I'd try upgrading to the latest 2.4.2-ac?? series.

Let me know if I'm mistaken about this one guys...

Jasmeet

Quoted 14 lines · Mike Fedyk
Quoted 11 lines · Shane Wegner

Hi,

Whenever I write a substantial amount of data (200mb) to disk, I get these messages. The disks lock for about 10 seconds and then come back for about 10 seconds again. This continues until the data is successfully written.

ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hde: DMA disabled

It looks like you have set your drive for a dma mode it doesn't support.

Quoted 8 lines

HTH

Mike
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

- - -
Jasmeet Sidhu
Unix Systems Administrator
ArrayComm, Inc.
[email protected]
www.arraycomm.com