ISSUE : ppp failure with kernel 2.4.2 - used to work with 2.4.0
1 - ppp failure with kernel 2.4.2 - used to work with 2.4.0
2 - Kernel 2.4.2 has been compiled exactly with the same options (config) as the 2.4.0.
Now when I try to reach my ISP, everything runs well until pppd launch the serial connection (see the message file attached)
3 - Keywords : kernel ppp
4 - Kernel version : Linux version 2.4.2 ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.0))
5 - Extract of the /var/log/message file :
Mar 12 14:22:14 a0 ifup-ppp: pppd started for ppp0 on /dev/ttyS2 at 115200 Mar 12 14:22:14 a0 pppd[808]: pppd 2.3.11 started by root, uid 0 Mar 12 14:22:15 a0 WvDial: WvDial: Internet dialer version 1.41 Mar 12 14:22:15 a0 WvDial: Initializing modem. Mar 12 14:22:15 a0 WvDial: Sending: ATZ Mar 12 14:22:15 a0 WvDial: ATZ Mar 12 14:22:15 a0 WvDial: OK Mar 12 14:22:15 a0 WvDial: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 S11=55 +FCLASS=0 Mar 12 14:22:15 a0 WvDial: ATQ0 V1 E1 S0=0 &C1 &D2 S11=55 +FCLASS=0 Mar 12 14:22:15 a0 WvDial: OK Mar 12 14:22:15 a0 WvDial: Sending: ATM0L1 Mar 12 14:22:16 a0 WvDial: ATM0L1 Mar 12 14:22:16 a0 WvDial: OK Mar 12 14:22:16 a0 WvDial: Modem initialized. Mar 12 14:22:16 a0 WvDial: Sending: ATDT ....................... Mar 12 14:22:16 a0 WvDial: Waiting for carrier. Mar 12 14:22:16 a0 WvDial: ATDT ................. mar 12 14:22:25 a0 PAM_unix[843]: (su) session opened for user root by ..(uid=....) Mar 12 14:22:38 a0 WvDial: CONNECT 31200/ARQ/V34/LAPM/V42BIS Mar 12 14:22:38 a0 WvDial: Carrier detected. Waiting for prompt. Mar 12 14:22:38 a0 WvDial: Login: Mar 12 14:22:38 a0 WvDial: Looks like a login prompt. Mar 12 14:22:38 a0 WvDial: Sending: .............. Mar 12 14:22:39 a0 WvDial: .............. Mar 12 14:22:39 a0 WvDial: Password: Mar 12 14:22:39 a0 WvDial: Looks like a password prompt. Mar 12 14:22:39 a0 WvDial: Sending: (password) Mar 12 14:22:39 a0 WvDial: Entering PPP Session. Mar 12 14:22:39 a0 WvDial: IP address is ............ Mar 12 14:22:39 a0 WvDial: MTU is 1524. Mar 12 14:22:39 a0 WvDial: Looks like a welcome message. Mar 12 14:22:39 a0 pppd[808]: Serial connection established. Mar 12 14:22:39 a0 pppd[808]: ioctl(PPPIOCGFLAGS): Invalid argument Mar 12 14:22:39 a0 pppd[808]: Hangup (SIGHUP) Mar 12 14:22:39 a0 pppd[808]: Exit.
6 - at the end of rp3 (or wvdial, same result), pppd aborts ...
7.1 - output of ver_linux : see file attached
7.2 - /proc/cpuinfo : see file attached
7.3 - /proc/modules : no such file (no option module compiled in kernel)
7.4 - /proc/ioport & /proc/iomem : see files attached
7.5 - output of lspci -vvv : see file attached
7.6 - /proc/scsi/scsi : Attached devices: none
Best regards and good luck (many thanks in advance)
Pascal Bonfils / Paris - France
[email protected]
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 1.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: e4000000-e5ffffff Prefetchable memory behind bridge: e7000000-e77fffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at f000 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at e000 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:08.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 26)
Subsystem: Tekram Technology Co.,Ltd. DC390F Ultra Wide SCSI Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at e400 [size=256] Region 1: Memory at e7801000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at e7800000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at e6000000 [disabled] [size=64K] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at e7802000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [60] Vital Product Data
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 86C326 (rev 0b) (prog-if 00 [VGA])
Subsystem: Palit Microsystems Inc. SiS6326 GUI Accelerator
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e7000000 (32-bit, prefetchable) [size=8M]
Region 1: Memory at e5000000 (32-bit, non-prefetchable) [size=64K]
Region 2: I/O ports at d000 [size=128]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 1.0
Status: RQ=1 SBA- 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000c83ff : Extension ROM
000f0000-000fffff : System ROM
00100000-0bffffff : System RAM
00100000-00240fcb : Kernel code
00240fcc-002adae3 : Kernel data
e0000000-e3ffffff : Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge e4000000-e5ffffff : PCI Bus #01
e5000000-e500ffff : Silicon Integrated Systems [SiS] 86C326
e7000000-e77fffff : PCI Bus #01
e7000000-e77fffff : Silicon Integrated Systems [SiS] 86C326
e7800000-e7800fff : Symbios Logic Inc. (formerly NCR) 53c875 e7801000-e78010ff : Symbios Logic Inc. (formerly NCR) 53c875 e7802000-e78020ff : Realtek Semiconductor Co., Ltd. RTL-8139
e7802000-e78020ff : eth0
ffff0000-ffffffff : reserved
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02e8-02ef : serial(set)
02f8-02ff : serial(set)
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03e8-03ef : serial(set)
03f6-03f6 : ide0
03f8-03ff : serial(set)
0cf8-0cff : PCI conf1
4000-403f : Intel Corporation 82371AB PIIX4 ACPI 5000-501f : Intel Corporation 82371AB PIIX4 ACPI d000-dfff : PCI Bus #01
d000-d07f : Silicon Integrated Systems [SiS] 86C326
e000-e01f : Intel Corporation 82371AB PIIX4 USB
e000-e01f : usb-uhci
e400-e4ff : Symbios Logic Inc. (formerly NCR) 53c875
e400-e47f : sym53c8xx
e800-e8ff : Realtek Semiconductor Co., Ltd. RTL-8139
e800-e8ff : eth0
f000-f00f : Intel Corporation 82371AB PIIX4 IDE
f000-f007 : ide0
f008-f00f : ide1
processor : 0vendor_id : GenuineIntel
cpu family : 6
model : 3
model name : Pentium II (Klamath)
stepping : 4
cpu MHz : 233.345
cache size : 512 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov mmx
bogomips : 465.30
-- Versions installed: (if some fields are empty or looks -- unusual then possibly you have very old versions) Linux a0.abi.org 2.4.2 #2 lun mar 12 14:04:23 CET 2001 i686 unknown
Kernel modules 2.3.14 Gnu C 2.96 Binutils 2.10.0.18 Linux C Library 6 -> libc-2.2.so Procps 2.0.7 Mount 2.10m Net-tools (2000-05-21) Kbd [option...] Sh-utils 2.0 Sh-utils Parker. Sh-utils Sh-utils Inc. Sh-utils NO Sh-utils PURPOSE.
Quoted 1 line · Pascal Bonfils
Mar 12 14:22:14 a0 pppd[808]: pppd 2.3.11 started by root, uid 0
^^^^^^^^^^^^
You should upgrade to ppp-2.4
E.g. linuxcare.com.au/pub/ppp
Andreas