Skip to contentSkip to conversation

VIA vt82c686b and UDMA(100)

DISCUSSION David Balazic 2 participants 2 messages Mar 23, 2001 – Mar 24, 2001

lore
Share & tools
lore
#0 lore raw
Quoted 11 lines · Brian Dushaw

Dear Linux Kernel Wisemen,
I have been following the discussion of the VIA vt82c686b chipset
and the troubles people have had in getting UDMA(100) to work. This is to report that I have now tried the 2.4.2-ac20 kernel and the 2.2.18 kernel with Andre's patch (dated March 20) and neither of them get the disk speed up to where it ought to be. hdparm -t reports back 11 MB/s or so for either kernel.
VIA82CXXX enabled, and I also tried the ide0=ata66 flag, in desparation. At boot up both kernels report the disk as UDMA(100) - everything
seems to be peachy keen, but for the sluggish disk performance.

Quoted 3 lines

Merely a report from the front lines,

B.D.

Do you also have IDE_AUTO_WHATEVER option enabled ,
as suggested ( no, commanded ) in the VIA_IDE_OPTION help text ? ( press '?' when selecting the VIA IDE driver option )

cat /proc/ide/via ?

What do you think is the "correct" transfer rate of the disk ?

For the record , I have a MSI K7T Pro2A board ( VIA KT133 with a vt82c686b south bridge ) and a IBM DTLA 307045 hard drive on a 80 wire IDE cable ( set to CABLE-SELECT , connected to the end connector; you must always first use both connectors on the end of the cable ! never left one end unused )

Without doing any settings with hdparm, I get the full transfer rate of the disk, measured with hdparm : ~35MB/s

kernel is 2.4.recent or redhat recent 2.4.x versions.

Signature · 4 lines
David Balazic
--------------
"Be excellent to each other." - Bill & Ted
- - - - - - - - - - - - - - - - - - - - - -
#1 lore raw

Thanks to all for their advice on this problem. So far I've tried hdparm flags six ways from sunday to no effect, but I have yet to try suggestions such as those below. Alas I have to set aside this problem for the next few weeks.

In the mean time, I note that the linux machines at my Lab are being subjected to fairly severe security attacks at the moment (the latest involved a hold in the bind DNS server (?) ) - a reminder to all to keep applying those updates and security patches.

B.D.

Quoted 38 lines · David Balazic
Quoted 11 lines · Brian Dushaw

Dear Linux Kernel Wisemen,
I have been following the discussion of the VIA vt82c686b chipset
and the troubles people have had in getting UDMA(100) to work. This is to report that I have now tried the 2.4.2-ac20 kernel and the 2.2.18 kernel with Andre's patch (dated March 20) and neither of them get the disk speed up to where it ought to be. hdparm -t reports back 11 MB/s or so for either kernel.
VIA82CXXX enabled, and I also tried the ide0=ata66 flag, in desparation. At boot up both kernels report the disk as UDMA(100) - everything
seems to be peachy keen, but for the sluggish disk performance.

Quoted 3 lines

Merely a report from the front lines,

B.D.

Do you also have IDE_AUTO_WHATEVER option enabled ,
as suggested ( no, commanded ) in the VIA_IDE_OPTION help text ? ( press '?' when selecting the VIA IDE driver option )

cat /proc/ide/via ?

What do you think is the "correct" transfer rate of the disk ?

For the record , I have a MSI K7T Pro2A board ( VIA KT133 with a vt82c686b south bridge ) and a IBM DTLA 307045 hard drive on a 80 wire IDE cable ( set to CABLE-SELECT , connected to the end connector; you must always first use both connectors on the end of the cable ! never left one end unused )

Without doing any settings with hdparm, I get the full transfer rate of the disk, measured with hdparm : ~35MB/s

kernel is 2.4.recent or redhat recent 2.4.x versions.

Signature · 12 lines
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

Brian Dushaw
Applied Physics Laboratory
University of Washington
1013 N.E. 40th Street
Seattle, WA  98105-6698
(206) 685-4198   (206) 543-1300
(206) 543-6785 (fax)
[email protected]

Web Page:  http://staff.washington.edu/dushaw/index.html