SMP not using all 4GB Mem

I have attached a question concerning using 4GB of memory on an SMP.

Thanks for the time,
Dave

SMP Not using all 4GB Ram Question:
---------------------------------------------------------------------
I am using a Compaq Proliant 8500 SMP with 8 550 Mhz processors and 4GB of RAM. Using Kernel 2.4.3 and Redhat 6.2

I have the (4GB) High Memory Support enabled.

I seem not to be able to use more that 1GB of memory.

The Following is my /proc/meminfo file

----------------------------------------------------------------------
total: used: free: shared: buffers: cached:

Mem:  3952427008 339447808 3612979200        0 256139264 25030656
Swap: 1048633344        0 1048633344
MemTotal:      3859792 kB
MemFree:       3528300 kB
MemShared:           0 kB
Buffers:        250136 kB
Cached:          24444 kB
Active:          16628 kB
Inact_dirty:    257952 kB
Inact_clean:         0 kB
Inact_target:      172 kB
HighTotal:     3014624 kB
HighFree:      2978372 kB
LowTotal:       845168 kB
LowFree:        549928 kB
SwapTotal:     1024056 kB
SwapFree:      1024056 kB

--------------------------------------------------------------

I wrote the following program that simply allocates 100M of memory and then write to it.

#include <stdio.h>

int main (void)
{

  char *p;
  unsigned int i;
  p = malloc (100000000);

while (1)

    {
      for (i=0;i<100000000;i++)
        *(p+i) = 5;
      sleep (1);
      for (i=0;i<100000000;i++)
        *(p+i) = 6;
      sleep(1);
    }
}

I can run 9 copies of this program to take up 900M of memory. When I attempt to start the 10th process, the whole world goes nuts. The X-window that it was started in closes and I continue to get a signal 11 interrupt whenever I run a shell command or attempt to compile.

I have another program that will allocate ~2GB of memory and then write data to it. It attempts to read the data back and fails around the 850-900M mark.

#include <stdio.h>
#include <string.h>
#include <sys/mman.h>

int main (void)

{

  int done = 0;
  unsigned int i = 0x7feee800; 
  char *p;
  char *p2;
  unsigned int x;

   p = malloc(i);
      
   sleep (1);

for (x=0;x<i;x++)

    {
    *(p+x) = 5;
    if (*(p+x) !=5)
      {
       printf("first Error %x  %x Address = %x \n", p, x, p+x);
              free(p);
	      return (0);  
      }  
    }

for (x=0;x<i;x++)

    if (*(p+x) !=5)
      {
       printf("5 Error %x  %x Address = %x Value = %x \n", p, x, p+x, *(p+x));
            free(p); 
	    return (0); 
       sleep(1); 
      }

memset(p, 10, i);
for (x=0;x<(i-1);x++)

    if (p[x] !=10)
      {
       printf("A Error %i  %x\n", p[x], x);
       /* free(p);
	  return (0);*/
      }

  printf("Done\n");
  free(p);
  return (0);

}
--------------------------

Example Run Result:

5 Error 4010f008 32650ff8 Address = 72760000 Value 67

------------------------

The failing address is always a multiple of 0x10000.

Could you give me some info on what I am doing wrong?

Thanks for your time,
Dave