Skip to contentSkip to conversation

2.4.9: PDC20267 not working

DISCUSSION Joe Fago 4 participants 6 messages Sep 10, 2001

lore
Share & tools
lore

Joe Fago

author
#0 lore raw

Hi,

System hangs on boot:

Uniform Multi-Platform E_IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20267: IDE controller on PCI bus 00 dev 40
PCI: Assigned IRQ 10 for device 00:08.0
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode
ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda: pio, hdb: pio
ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc: pio, hdd: DMA
hda: Maxtor 2B020H1, ATA DISK drive

This is the only device attached to the controller. Any suggestions?

Thanks,
Joe

#1 lore raw
Quoted 5 lines · Joe Fago

System hangs on boot:

PDC20267: IDE controller on PCI bus 00 dev 40

This is the only device attached to the controller. Any suggestions?

I have seen this before. I have a system that will do it every time right now, in fact. You can try setting interrupts to edge-triggered in your BIOS if it has such an option; this usually ``fixes'' the problem for me. Of course, it will mean you can't share PCI interrupts, if I understand it correctly. However, I'm not sure what's going on and nobody has commented on it thus far that I know of. :(

-Jacob

#2 lore raw

----- Original Message -----
From: "Jacob Luna Lundberg" <[email protected]>
To: "Joe Fago" <[email protected]>
Cc: <[email protected]>
Sent: Sunday, September 09, 2001 6:46 PM
Subject: Re: 2.4.9: PDC20267 not working

Quoted 7 lines · Joe Fago
Quoted 4 lines

System hangs on boot:

PDC20267: IDE controller on PCI bus 00 dev 40

Quoted 8 lines
Quoted 1 line

This is the only device attached to the controller. Any suggestions?

I have seen this before. I have a system that will do it every time right now, in fact. You can try setting interrupts to edge-triggered in your BIOS if it has such an option; this usually ``fixes'' the problem for me. Of course, it will mean you can't share PCI interrupts, if I understand it correctly. However, I'm not sure what's going on and nobody has commented on it thus far that I know of. :(

Mine has problems as well. I know there are workarounds, but I'm not experienced enough to do these. Joe: what error messages do you get? I get the "hde: timeout waiting for dma" errors. After that I have to cold start my PC to get it working. BTW, I have a PDC20265, but I think these are probably almost identical (or at least the behaviour we are getting is probably due to the same problem in the code).

I also suspect that maybe what kind of hard drive you have makes a difference as well, because some people can get their Promise IDE to work fine, while others can't. I have a Quantum Fireball Plus AS.

In case you didn't know, Andre Hedrick met with some dude from Promise called Craig Lyons on Wednesday. I haven't heard of any news from the meeting, but supposedly Craig was going to give Andre some API for the Ultra/Fastrack line of chips. Hopefully it went down on Wednesday.

David Grant

author
#3 lore raw
In reply to Jacob Luna Lundberg
Quoted 19 lines · Jacob Luna Lundberg
Quoted 5 lines · Joe Fago

System hangs on boot:

PDC20267: IDE controller on PCI bus 00 dev 40

This is the only device attached to the controller. Any suggestions?

I have seen this before. I have a system that will do it every time right now, in fact. You can try setting interrupts to edge-triggered in your BIOS if it has such an option; this usually ``fixes'' the problem for me. Of course, it will mean you can't share PCI interrupts, if I understand it correctly. However, I'm not sure what's going on and nobody has commented on it thus far that I know of. :(

(quoted diff) +0 -2
-Jacob
 
-
Quoted 4 lines

To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Thanks, that worked -- well the opposite worked. I had to set mine to triggered by level' rather than edge'. But I never would have suspected it if you hadn't brought it up.

Thanks Again,
Joe

author
#4 lore raw
In reply to Jacob Luna Lundberg
Quoted 7 lines
Quoted 7 lines · Joe Fago
Quoted 4 lines

System hangs on boot:

PDC20267: IDE controller on PCI bus 00 dev 40

Quoted 7 lines
Quoted 4 lines
Quoted 1 line

This is the only device attached to the controller. Any suggestions?

You can try setting interrupts to edge-triggered in your BIOS if it has such an option;

Joe: what error messages do you get? I get
the "hde: timeout waiting for dma" errors. After that I have to cold start

I had no more information, the system just hung after the `hda:' line. Setting the
bios to interrupts triggered by `level' seems to get things going in my case.

I guess these are workarounds rather than solutions. I was just happy to get the system booted. It seems that we can reproduce this particular problem, and I'd be glad to participate in any testing that might assist Andre's efforts.

Thanks,
Joe

#5 lore raw
In reply to Joe Fago

Hi!

Quoted 7 lines · Joe Fago

PDC20267: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode
ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda: pio, hdb: pio
ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc: pio, hdd: DMA
hda: Maxtor 2B020H1, ATA DISK drive

This is the only device attached to the controller. Any suggestions?

ASUS A7V with on-board PDC20265, kernel 2.4.9 with ACPI support - it hangs on detection of the last drive (hde). I've disabled APM and ACPI altogether in the kernel and now it works.
I didn't play with edge/level setting of interrupts.

Signature · 2 lines
best regards,
Rok Papež.