Direct PCI access broken in 2.4.10-pre
2.4.10-pre3 and later fail to boot on my Compaq XL box. It claims that PCI isn't supported. This board doesn't use the PCI BIOS because the entry point is in high memory.
'cvs up -r v2_4_10-pre2 arch/i386/boot/pci-pc.c' fixes it.
A happy boot with the old pci-pc.c:
PCI: BIOS32 entry (0xc00fa000) in high memory, cannot use.
PCI: Using configuration type 2
PCI: Probing PCI hardware
An unhappy boot with the new one:
PCI: BIOS32 entry (0xc00fa000) in high memory, cannot use.
PCI: System does not support PCI
An unhappy boot with the new one and 'pci=conf2':
PCI: Using configuration type 2
PCI: Probing PCI hardware
PCI: device 00:01.0 has unknown header type 7f, ignoring.
PCI: device 00:02.0 has unknown header type 7f, ignoring.
PCI: device 00:03.0 has unknown header type 7f, ignoring.
PCI: device 00:04.0 has unknown header type 7f, ignoring.
PCI: device 00:05.0 has unknown header type 7f, ignoring.
PCI: device 00:06.0 has unknown header type 7f, ignoring.
PCI: device 00:07.0 has unknown header type 7f, ignoring.
PCI: device 00:08.0 has unknown header type 7f, ignoring.
PCI: device 00:09.0 has unknown header type 7f, ignoring.
PCI: device 00:0a.0 has unknown header type 7f, ignoring.
PCI: device 00:0e.2 has unknown header type 7f, ignoring.
PCI: device 00:0e.3 has unknown header type 7f, ignoring.
PCI: device 00:0e.4 has unknown header type 7f, ignoring.
PCI: device 00:0e.5 has unknown header type 7f, ignoring.
PCI: device 00:0e.6 has unknown header type 7f, ignoring.
PCI: device 00:0e.7 has unknown header type 7f, ignoring.
PCI: Cannot allocate resource region 0 of device 00:0e.0
PCI: Cannot allocate resource region 1 of device 00:0e.1
PCI: Cannot allocate resource region 2 of device 00:0e.1
PCI: Cannot allocate resource region 3 of device 00:0e.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
<deadlock>
--
dwmw2
Quoted 7 lines · David Woodhouse
2.4.10-pre3 and later fail to boot on my Compaq XL box. It claims that PCI isn't supported. This board doesn't use the PCI BIOS because the entry point is in high memory.
'cvs up -r v2_4_10-pre2
arch/i386/boot/pci-pc.c' fixes it.
Quoted 8 lines
A happy boot with the old
pci-pc.c:
PCI: BIOS32 entry (0xc00fa000) in high memory, cannot use.
PCI: Using configuration type 2
PCI: Probing PCI hardwareAn unhappy boot with the new one:
PCI: BIOS32 entry (0xc00fa000) in high memory, cannot use.
PCI: System does not support PCI
Patch attached that fixes typecasting problems with PCI Type 2 accesses.
Signature · 1 line
Brian Gerst
arch/i386/kernel/pci-pc.c +3 -7
@@ -261,18 +261,14 @@u32 data; result =pci_conf2_read (0 , dev->bus->number,PCI_SLOT (dev->devfn),PCI_FUNC (dev->devfn), where,2 , &data); - *value = (u8 )data; + *value = (u16 )data;return result; }static int pci_conf2_read_config_dword (struct pci_dev *dev,int where,u32 *value) { -int result; -u32 data; - result =pci_conf2_read (0 , dev->bus->number,PCI_SLOT (dev->devfn), -PCI_FUNC (dev->devfn), where,4 , &data); - *value = (u8 )data; -return result; +return pci_conf2_read (0 , dev->bus->number,PCI_SLOT (dev->devfn), +PCI_FUNC (dev->devfn), where,4 , value); }static int pci_conf2_write_config_byte (struct pci_dev *dev,int where,u8 value)
Quoted 2 lines · [email protected] said:
Patch attached that fixes typecasting problems with PCI Type 2
accesses.
That appears to fix it. Thanks.
--
dwmw2