Skip to contentSkip to conversation

excessive interrupts on network cards

DISCUSSION Chris Newton 2 participants 2 messages Sep 25, 2001

lore
Share & tools
lore
#0 lore raw

Yea, it is a single port card... I had meant to mention that in the email I sent out... ie: that it wasn't reporting correctly... but, I didnt really think it was related, since the eepro was doing the same thing.

As for comparing with ifconfig, I ran 'watch 1 ifconfig -a', and sure
enough, I have about ~7000-7500 packets coming in right now. And, the 'procinfo -D', reports ~21000-22000 interrupts per second.

Other sources I have used to confirm packet rate... include output from
'sniffer', a flow generator that was monitoring that link, and the hub this machine is plugged into.

the hub has 3 active ports.. port 1 is one side of our internet conenction
(out to our provider), port 2 was from the hub over to our main router... port 3 is a mirror of the IN on port 1 and the OUT on port 2 to port 3. Comparing, and verifying, showed port 3 getting 10K packets (this afternoon, which obviously drops at night, which it is here now), and down to 7K now.

Chris

Quoted 6 lines

===== Original Message From Andrew Morton <[email protected]> =====

Quoted 4 lines · Chris Newton

Hi,

I 'think' the number of interrupts being generated for the network

traffic I

Quoted 1 line
Quoted 1 line

monitor, is excessive. Having talked quikly with Donald Becker, he

indicated

Quoted 1 line
Quoted 1 line

that I should be seeing a little less than the number of RX/TX packets/s on

a

Quoted 1 line
Quoted 1 line

wire, in terms of interrupts/s. That, however, is not what I am seeing. I

am

Quoted 3 lines
Quoted 3 lines

seeing 3 times as many interrupts/s as I am seeing packets/s.

I have used three network devices to look at the stream I am monitoring,

and

Quoted 1 line
Quoted 1 line

it is usually aorund 5K packet/s IN, and 5K out, fed full duplex into a

single

Quoted 3 lines
Quoted 1 line

3Com 3c982 (2.4.10 kernel reports that anyways). However, watching:

3c982 is a dual-port server NIC. Is your card dual-port? If not, it's

probably

Quoted 12 lines

a 3c980, and I goofed :)

Quoted 1 line

'procinfo -D', reports on the order of 30,000 interrupts per second.

That does sound rather high. You should compare the interrupt rate with the packet rate from `ifconfig' or /proc/net/dev.

Normally, 3c59x will show approx three Tx packets per interrupt and one Rx packet per interrupt. It varies with workload, but it tends to vary in the "good" direction - at higher packet rates, we do more work in a single interrupt and the interrupt-per-packet rate falls.

#1 lore raw
Quoted 7 lines · Chris Newton

Yea, it is a single port card... I had meant to mention that in the email I sent out... ie: that it wasn't reporting correctly... but, I didnt really think it was related, since the eepro was doing the same thing.

As for comparing with ifconfig, I ran 'watch 1 ifconfig -a', and sure
enough, I have about ~7000-7500 packets coming in right now. And, the 'procinfo -D', reports ~21000-22000 interrupts per second.

This is heavily dependant on the interrupt mitigation features that a card has. At least for the ns83820 driver, I'm testing a technique where the driver essentially switches to polled mode once the interrupt load goes above a certain threshold, thereby limiting the load to ~2500 irq/sec. Combined with carefully placed data prefetching, I'm seeing a huge increase in performance. Of course, this comes at the expense of latency.

-ben