Skip to contentSkip to conversation

via82cxxx_audio doesn't play audio?

DISCUSSION Erik Andersen 4 participants 5 messages Nov 30, 2001

lore
Share & tools
lore
#0 lore raw

I went out the other day and bought an Athlon to replace my aging celeron 400. I installed an Epox EP-8KHA+ with an Athlon XP 1600+. The VIA 8233 Southbridge on the motherboard has builtin audio

00:11.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 30)
Flags: medium devsel, IRQ 11
I/O ports at cc00 [size=256]
Capabilities: [c0] Power Management version 2

I have enabled CONFIG_SOUND_VIA82CXXX and CONFIG_MIDI_VIA82CXXX in 2.4.16 and everything seems to be fine. When I load the modules I see this:

    Via 686a audio driver 1.9.1
    ac97_codec: AC97 Audio codec, id: 0x414c:0x4710 (ALC200/200P)
    via82cxxx: board #1 at 0xCC00, IRQ 11

When I go to play audio, no sound is produced. The mixer works. I can load up the bttv drivers and I actually hear audio from xawtv (so tvaudio is doing something right behind the scenes). But standard apps such as xmms produce no sound. Does this driver not work for anyone else?

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

#1 lore raw
Quoted 18 lines · Erik Andersen

I went out the other day and bought an Athlon to replace my aging celeron 400. I installed an Epox EP-8KHA+ with an Athlon XP 1600+. The VIA 8233 Southbridge on the motherboard has builtin audio

00:11.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 30)
Flags: medium devsel, IRQ 11
I/O ports at cc00 [size=256]
Capabilities: [c0] Power Management version 2

I have enabled CONFIG_SOUND_VIA82CXXX and CONFIG_MIDI_VIA82CXXX in 2.4.16 and everything seems to be fine. When I load the modules I see this:

    Via 686a audio driver 1.9.1
    ac97_codec: AC97 Audio codec, id: 0x414c:0x4710 (ALC200/200P)
    via82cxxx: board #1 at 0xCC00, IRQ 11
Quoted 5 lines

When I go to play audio, no sound is produced. The mixer works. I can load up the bttv drivers and I actually hear audio from xawtv (so tvaudio is doing something right behind the scenes). But standard apps such as xmms produce no sound. Does this driver not work for anyone else?

You need ALSA drivers.

Via 686 audio is different from Via 8233 audio, and you have the latter. The PCI ids were added to via82cxxx_audio, but they need to be removed since they apparently do not work (contrary to one report I received).

Jeff

Signature · 3 lines
Jeff Garzik      | Only so many songs can be sung
Building 1024    | with two lips, two lungs, and one tongue.
MandrakeSoft     |         - nomeansno
#2 lore raw
In reply to Erik Andersen

I have a similar problem with the 686b south bridge. The module loads fine but no sound comes out. The alsa drivers don't work for this computer either.

Via 686a audio driver 1.9.1
PCI: Found IRQ 11 for device 00:07.5
IRQ routing conflict for 00:07.5, have irq 5, want irq 11
PCI: Sharing IRQ 11 with 00:0a.0
PCI: Sharing IRQ 11 with 00:0b.0
ac97_codec: AC97 Audio codec, id: 0x4144:0x5361 (Unknown)
via82cxxx: board #1 at 0x1000, IRQ 5

zahra:/home/jcassidy# cat /proc/interrupts 
           CPU0       
  0:    3078777          XT-PIC  timer
  1:      10593          XT-PIC  keyboard
  2:          0          XT-PIC  cascade
  3:       1438          XT-PIC  ide2
  5:          0          XT-PIC  via82cxxx
  8:          1          XT-PIC  rtc
 10:          0          XT-PIC  acpi
 11:      26056          XT-PIC  Texas Instruments PCI1410 PC card Cardbus Controller, eth0
 12:      67491          XT-PIC  PS/2 Mouse
 14:       9866          XT-PIC  ide0
 15:          6          XT-PIC  ide1
NMI:          0 
ERR:          0

00:07.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 50)
Subsystem: Compaq Computer Corporation: Unknown device 0097
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1854 [size=4]
Region 2: I/O ports at 1850 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Quoted 15 lines

You need ALSA drivers.

Via 686 audio is different from Via 8233 audio, and you have the latter. The PCI ids were added to via82cxxx_audio, but they need to be removed since they apparently do not work (contrary to one report I received).

Jeff

Signature · 3 lines
Jeff Garzik      | Only so many songs can be sung
Building 1024    | with two lips, two lungs, and one tongue.
MandrakeSoft     |         - nomeansno
#3 lore raw
In reply to Erik Andersen
Quoted 5 lines · Jeff Garzik
Quoted 4 lines · Erik Andersen

I went out the other day and bought an Athlon to replace my aging celeron 400. I installed an Epox EP-8KHA+ with an Athlon XP 1600+. The VIA 8233 Southbridge on the motherboard has builtin audio

[---------snip--------]

Quoted 2 lines
Quoted 2 lines

When I go to play audio, no sound is produced. The mixer works.

[---------snip--------]

Quoted 7 lines

You need ALSA drivers.

Via 686 audio is different from Via 8233 audio, and you have the latter. The PCI ids were added to via82cxxx_audio, but they need to be removed since they apparently do not work (contrary to one report I received).

Thanks. The ALSA drivers indeed work just great. So yeah, do pull the Via 8233 audio PCI IDs from via82cxxx_audio. ALSA seems to be the One True Path for these monsters.

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

#4 lore raw
In reply to Erik Andersen
Quoted 2 lines · Erik Andersen

But standard apps such as xmms produce no sound. Does this driver not work for anyone else?

Yeah, works for me on an Epox 8KTA3+ pro, same module.

PCI: Found IRQ 12 for device 00:07.5
ac97_codec: AC97 Audio codec, id: 0x4943:0x4511 (ICE1232)
via82cxxx: board #1 at 0x9C00, IRQ 12

Bus 0, device 7, function 5:
Multimedia audio controller: VIA Technologies, Inc. AC97 Audio

      Controller (rev 80).
      IRQ 12.
      I/O at 0x9c00 [0x9cff].
      I/O at 0xa000 [0xa003].
      I/O at 0xa400 [0xa403].

Alsa otoh doesn't work for me (it used to, but then...).

Which mixer do you use? gom works for me, maybe different mixers don't work with all cards (I had that problem with 2.0 kernels, don't know about todays state, though).

Regs,
Sven

Signature · 4 lines
Sven Riedel                      [email protected]
Osteroeder Str. 6 / App. 13      [email protected]
38678 Clausthal                  "Call me bored, but don't call me boring."
                                 - Larry Wall