cdrecord reports size vs. capabilities error....
This I believed may have been asked before, but I am new to this list and I hope I can get it resolved.
I have a IDE CDR as hdb and a IDE CDRW as hdc, no problem. I know in order to use cdrecord I must use ide-scsi, no problem as I had this exact same setup working with cdrecord when this was a 2.2.x system. Ok, I upgrade the hard drive, hda, and install 2.4.5 kernel from Slackware 8.0. I always install just what I need,and install things as I need them, usually from source. That's how you learn.
Ok, I need cdrecord working. No problem, I've done this before. Get the cdrtools-1.10.tar.gz and have at. builds no problem. Build kernel with scsi emulation, put the append command in lilo.conf, do the modules.conf thing and link /dev/cdrom to /dev/scd0 and /dev/cdrw to /dev/scd1. Reboot and I can mount both /dev/cdrom and /dev/cdrw as ro filesystems. lsmod shows:
Module Size Used by
isofs 18032 1 (autoclean) sr_mod 13024 1 (autoclean) sg 21408 0 (autoclean) ide-scsi 7904 1 ide-cd 26432 0 cdrom 27520 0 [sr_mod ide-cd] scsi_mod 81904 3 (autoclean) [sr_mod sg ide-scsi] 3c59x 24224 1
Ok, I try cdrecord -scanbus, and get he following warning:
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling Linux sg driver version: 3.1.17
Using libscg version 'schily-0.5'
scsibus0:
cdrecord: Warning: controller returns wrong size for CD capabilities page.
0,0,0 0) 'E-IDE ' 'CD-ROM 50X ' '50 ' Removable
CD-ROM
0,1,0 1) 'HP ' 'CD-Writer+ 9100 ' '1.0c' Removable
CD-ROM
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *Where did the Warning: come from? Trying to burn from xcdroast causes an error box stating the same and refuses to write.
I did everything like the cd writer how-to specifies, just like I did before, I think? Did I miss something?
I google searched and found plenty of postings with the same problem, but couldn't find any with the answer. One thing I did notice that they all involved 2.4.x kernel. Is that the problem?
Quoted 4 lines · Jeff
cdrecord: Warning: controller returns wrong size for CD capabilities page.
0,0,0 0) 'E-IDE ' 'CD-ROM 50X ' '50 ' RemovableCD-ROM
Correct me if I'm wrong, but that looks like cdrecord doesn't recognize your cd-rom correctly. Do you have added that drive also to your lilo.conf ?
Normally it would be enough to load the modules without any specific parameters.
Could you post your dmesg-output + lilo.conf parameters if possible ?
*Kristian
Quoted 4 lines
Quoted 4 lines
cdrecord: Warning: controller returns wrong size for CD capabilities page.
0,0,0 0) 'E-IDE ' 'CD-ROM 50X ' '50 ' RemovableCD-ROM
I get this same thing with a scsi cdrom at work. I have 2 of the exact same drives. a Teac cd-535s v1.0a the first one I get that message, the second works. However, the first one won't pull the tray back in via software.
Quoted 6 lines
Correct me if I'm wrong, but that looks like cdrecord doesn't recognize your cd-rom correctly. Do you have added that drive also to your lilo.conf ?
Normally it would be enough to load the modules without any specific parameters.
Could you post your dmesg-output + lilo.conf parameters if possible ?
Signature · 1 line
Lab tests show that use of micro$oft causes cancer in lab animals
Quoted 3 lines · Wakko Warner
I get this same thing with a scsi cdrom at work. I have 2 of the exact same drives. a Teac cd-535s v1.0a the first one I get that message, the second works. However, the first one won't pull the tray back in via software.
Is the first drive connected to /dev/hdb ? Does eject work on /dev/scd0 or /dev/hdb ?
*Kristian
That just means it is not a standard compliant CDRW drive. I've asked Joerg Schilling about this and that's what he said. I get the same thing.
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
scsibus0:
0,0,0 0) *
0,1,0 1) *
0,2,0 2) 'IOMEGA ' 'ZIP 100 ' 'J.03' Removable Disk
0,3,0 3) 'MATSHITA' 'CD-ROM CR-8008 ' '8.0e' Removable CD-ROM
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
scsibus1:
1,0,0 100) ' ' 'SMART100X/2400 ' '1.44' Removable CD-ROM
1,1,0 101) 'PLEXTOR ' 'CD-R PX-W1210A' '1.09' Removable CD-ROM
cdrecord: Warning: controller returns wrong size for CD capabilities page.
1,2,0 102) 'MATSHITA' 'CD-ROM CR-581-M ' '1.05' Removable CD-ROM
1,3,0 103) 'HP ' 'CD-Writer+ 7500 ' '1.0a' Removable CD-ROM
1,4,0 104) 'SONY ' 'CD-ROM CDU77E-Q ' '1.3a' Removable CD-ROM
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *Quoted 16 lines · Kristian Peters
Quoted 3 lines · Wakko Warner
I get this same thing with a scsi cdrom at work. I have 2 of the exact same drives. a Teac cd-535s v1.0a the first one I get that message, the second works. However, the first one won't pull the tray back in via software.
Is the first drive connected to
/dev/hdb? Does eject work on/dev/scd0or/dev/hdb?*Kristian
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 7 lines
Quoted 3 lines
I get this same thing with a scsi cdrom at work. I have 2 of the exact same drives. a Teac cd-535s v1.0a the first one I get that message, the second works. However, the first one won't pull the tray back in via software.
Is the first drive connected to
/dev/hdb? Does eject work on/dev/scd0or/dev/hdb?
Those drives are scsi drives, not IDE. they are the exact same drive but on different scsi controllers. I *HAVE* swapped them, it's the drive.
The scsi controllers are both adaptec aha-2940u cards.
Signature · 1 line
Lab tests show that use of micro$oft causes cancer in lab animals
Quoted 17 lines
That just means it is not a standard compliant CDRW drive. I've asked Joerg Schilling about this and that's what he said. I get the same thing.
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
scsibus0:0,0,0 0) * 0,1,0 1) * 0,2,0 2) 'IOMEGA ' 'ZIP 100 ' 'J.03' Removable Disk 0,3,0 3) 'MATSHITA' 'CD-ROM CR-8008 ' '8.0e' Removable CD-ROM 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) * scsibus1: 1,0,0 100) ' ' 'SMART100X/2400 ' '1.44' Removable CD-ROM
Quoted 8 lines
1,1,0 101) 'PLEXTOR ' 'CD-R PX-W1210A' '1.09' Removable CD-ROM
cdrecord: Warning: controller returns wrong size for CD capabilities page.
1,2,0 102) 'MATSHITA' 'CD-ROM CR-581-M ' '1.05' Removable CD-ROM
1,3,0 103) 'HP ' 'CD-Writer+ 7500 ' '1.0a' Removable CD-ROM
1,4,0 104) 'SONY ' 'CD-ROM CDU77E-Q ' '1.3a' Removable CD-ROM
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *Ok, but why would having 2 identical cdroms be different? they both have the same firmware, yet cdrecord -scanbus shows one of them with the wrong size thing. There's 2 scsi controllers, but if I swap them, the wrong size stays with the drive, not the controller.
Signature · 1 line
Lab tests show that use of micro$oft causes cancer in lab animals
Yeah, when I switched controllers etc it puts the message in different spots. I'm not sure why it does that.
You'll have to ask the guy who wrote the driver I guess.
Quoted 33 lines · Wakko Warner
Quoted 17 lines
That just means it is not a standard compliant CDRW drive. I've asked Joerg Schilling about this and that's what he said. I get the same thing.
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
scsibus0:0,0,0 0) * 0,1,0 1) * 0,2,0 2) 'IOMEGA ' 'ZIP 100 ' 'J.03' Removable Disk 0,3,0 3) 'MATSHITA' 'CD-ROM CR-8008 ' '8.0e' Removable CD-ROM 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) * scsibus1: 1,0,0 100) ' ' 'SMART100X/2400 ' '1.44' Removable CD-ROMQuoted 8 lines
1,1,0 101) 'PLEXTOR ' 'CD-R PX-W1210A' '1.09' Removable CD-ROM cdrecord: Warning: controller returns wrong size for CD capabilities page. 1,2,0 102) 'MATSHITA' 'CD-ROM CR-581-M ' '1.05' Removable CD-ROM 1,3,0 103) 'HP ' 'CD-Writer+ 7500 ' '1.0a' Removable CD-ROM 1,4,0 104) 'SONY ' 'CD-ROM CDU77E-Q ' '1.3a' Removable CD-ROM 1,5,0 105) * 1,6,0 106) * 1,7,0 107) *Ok, but why would having 2 identical cdroms be different? they both have the same firmware, yet cdrecord -scanbus shows one of them with the wrong size thing. There's 2 scsi controllers, but if I swap them, the wrong size stays with the drive, not the controller.
--
Lab tests show that use of micro$oft causes cancer in lab animals
I guess the problem was in my module.conf file, I forgot to add alias scd1 sr_mod. I didn't remember the capabilities error from before. The warning is still there in scanbus, but everything is now working correctly.
Thanks to everybody for their help.
Quoted 38 lines · war
Yeah, when I switched controllers etc it puts the message in different spots. I'm not sure why it does that.
You'll have to ask the guy who wrote the driver I guess.Quoted 31 lines · Wakko Warner
Quoted 17 lines
That just means it is not a standard compliant CDRW drive. I've asked Joerg Schilling about this and that's what he said. I get the same thing.
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
scsibus0:0,0,0 0) * 0,1,0 1) * 0,2,0 2) 'IOMEGA ' 'ZIP 100 ' 'J.03' Removable Disk 0,3,0 3) 'MATSHITA' 'CD-ROM CR-8008 ' '8.0e' Removable CD-ROM 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) * scsibus1: 1,0,0 100) ' ' 'SMART100X/2400 ' '1.44' Removable CD-ROMQuoted 8 lines
1,1,0 101) 'PLEXTOR ' 'CD-R PX-W1210A' '1.09' Removable CD-ROM cdrecord: Warning: controller returns wrong size for CD capabilities page. 1,2,0 102) 'MATSHITA' 'CD-ROM CR-581-M ' '1.05' Removable CD-ROM 1,3,0 103) 'HP ' 'CD-Writer+ 7500 ' '1.0a' Removable CD-ROM 1,4,0 104) 'SONY ' 'CD-ROM CDU77E-Q ' '1.3a' Removable CD-ROM 1,5,0 105) * 1,6,0 106) * 1,7,0 107) *Ok, but why would having 2 identical cdroms be different? they both have the same firmware, yet cdrecord -scanbus shows one of them with the wrong size thing. There's 2 scsi controllers, but if I swap them, the wrong size stays with the drive, not the controller.
Quoted 8 lines
Quoted 2 lines
--
Lab tests show that use of micro$oft causes cancer in lab animals-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/