Sony DSC-P71 Camera

DISCUSSION sean darcy 2 participants 2 messages May 29, 2002 1 message not in the archive

Share & tools

A message that is not in the archive (sent off-list or not yet received): [email protected]

sean darcy

author

2002-05-29 01:13 UTC #1 lore raw

You don't say which kernel you're using. I have a p71 which I can't get to work with 2.5.18 - see the mass storage thread. OTOH, a stock rh 2.4.18 kernel works just fine.

What does usbview show? What are the usb and scsi snips from .config. What hapens when you try to mount sd* ?

Quoted 36 lines · Colin Slater

Hello,
I just got a Sony DSC-P71 digital camera (wonderful), but it doesn't
seem to be working in linux. I beleive it uses the usb mass storage
driver, it seems to use an equivilent driver in windows. I have scsi,
usb, usb mass storage modules all loaded. dmesg after I load the usb-storage module, and then plug the camera in:
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
hub.c: USB new device connect on bus1/1, assigned device number 3 scsi0 : SCSI emulation for USB Mass Storage devices
I am useing devfs, and /dev/scsi is empty.
cat /proc/bus/usb/devices:
<snip>
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=054c ProdID=0010 Rev= 4.10
S:  Manufacturer=Sony
S:  Product=Sony DSC
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=ff Prot=01 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=  0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=  0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   8 Ivl=255ms
<snip>
All this happens regardless of NVdriver being loaded or not.
If someone with one of these cameras or the nearly identical DSC-P31 could help me, it would be appreciated
Colin

Colin Slater

2002-05-29 20:35 UTC #2 lore raw

Quoted 6 lines · sean darcy

You don't say which kernel you're using. I have a p71 which I can't get to work with 2.5.18 - see the mass storage thread. OTOH, a stock rh 2.4.18 kernel works just fine.
What does usbview show? What are the usb and scsi snips from .config. What hapens when you try to mount sd* ?

Yes, I forgoht to mention that im running 2.4.18. Here is a lsmod of all the relevent stuff I have loaded

root@neptune:~# lsmod
Module                  Size  Used by    Tainted: P
usb-storage            20820   0  (unused)
sr_mod                 11792   0  (autoclean) (unused)
scsi_mod               80648   1  (autoclean) [usb-storage sr_mod]

usbview doesnt show mutch more than /proc/bus/usb/devices. The cammera does show up in red in the left pane though. And I dont have any /dev/sd* devices. Are you useing the camera in "Normal" usb mode? somewhere in the setup they have an alternate mode, but dont know what the difference is.

Here's the usb & scsi sections from my .config:

# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_LONG_TIMEOUT is not set
CONFIG_USB_UHCI_ALT=y
# CONFIG_USB_OHCI is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH is not set
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_HID=y
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_DC2XX is not set
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_USS720 is not set

# SCSI support
#
CONFIG_SCSI=m
CONFIG_BLK_DEV_SD=m
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_DEBUG_QUEUES=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set

Signature · 3 lines

-----
GPG Key 0x7E959232; wwwkeys.pgp.net
861C AE70 158F C440  EEE1 397C 7CBD 1148 7E95 9232