swsusp needs clock corrected | 8193too needs reload
Hi
For my Tablet PC ACPI is very good working now .n The Transmeta 600Mhz sits on a ALi chipset with a Phoenix Bios
AC and battery are displayed.
processor can be influenced and throttle
i also get the temperature .
and with the swsusp i also can fully use S4 without any BIG problem
Only 2 things are not fully working with swsusp
after i resume from S4 , my clock is still at the time when it was suspended.
the secound thing is that i need to rmmod my 8139too Realtek eth0 chip and reinsert it by hand . although i get the correct messages at resume : " setting up half dupley 10/100 ...."
Anybody has a hint ...?
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 3 lines · Robert
Only 2 things are not fully working with swsusp
after i resume from S4 , my clock is still at the time when it was suspended.
Run hwclock --hctosys after resume (and preferable hwclock --systohc before)
Quoted 3 lines
the secound thing is that i need to rmmod my 8139too Realtek eth0 chip and reinsert it by hand . although i get the correct messages at resume : " setting up half dupley 10/100 ...."
I only used to to ifconfig eth0 down and up - this also renewed my DHCP address - very fine :-)
Markus
Signature · 12 lines
__________________ /"\ Markus Gaugusch \ / ASCII Ribbon Campaign [email protected] X Against HTML Mail / \ ------------------------------------------------------- This sf.net email is sponsored by:ThinkGeek Welcome to geek heaven. http://thinkgeek.com/sf
A message that is not in the archive (sent off-list or not yet received): Pine.LNX.4.44.0209161123420.12600-100000-sxQ525G0OhRQK2oVCIMtW7NldLUNz+W/@public.gmane.org
Hi!
Quoted 5 lines
Quoted 3 lines
Only 2 things are not fully working with swsusp
after i resume from S4 , my clock is still at the time when it was suspended.Run hwclock --hctosys after resume (and preferable hwclock --systohc before)
Actually this should be fixed in kernel (as we already do for apm). Patches welcome.
Pavel
Signature · 10 lines
Philips Velo 1: 1"x4"x8", 300gram, 60, 12MB, 40bogomips, linux, mutt, details at http://atrey.karlin.mff.cuni.cz/~pavel/velo/index.html. ------------------------------------------------------- This SF.NET email is sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 10 lines · Pavel Machek [[email protected]] wrote:
Hi!
Quoted 5 lines
Quoted 3 lines
Only 2 things are not fully working with swsusp
after i resume from S4 , my clock is still at the time when it was suspended.Run hwclock --hctosys after resume (and preferable hwclock --systohc before)
Actually this should be fixed in kernel (as we already do for apm). Patches welcome.
And I think that a similar clock fix is required for speedstep changes.
Faye`
Signature · 13 lines
Faye Pearson, Software Development Manager, ClaraNET Ltd. Tel 020 7903 3000 untold wealth, n.: What you left out on April 15th. ------------------------------------------------------- This SF.NET email is sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab
A message that is not in the archive (sent off-list or not yet received): [email protected]
Ahoj!
Quoted 10 lines
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
Only 2 things are not fully working with swsusp
after i resume from S4 , my clock is still at the time when it was suspended.Run hwclock --hctosys after resume (and preferable hwclock --systohc before)
Actually this should be fixed in kernel (as we already do for apm). Patches welcome.
And I think that a similar clock fix is required for speedstep changes.
No, that is completely orthogonal issue.
Signature · 9 lines
Casualities in World Trade Center: ~3k dead inside the building, cryptography in U.S.A. and free speech in Czech Republic. ------------------------------------------------------- This SF.NET email is sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 32 lines · [email protected] schrieb:
Quoted 5 lines · Robert
Hi
For my Tablet PC ACPI is very good working now .n The Transmeta 600Mhz sits on a ALi chipset with a Phoenix Bios
Quoted 10 lines
AC and battery are displayed.
processor can be influenced and throttle
i also get the temperature .
and with the swsusp i also can fully use S4 without any BIG problemOnly 2 things are not fully working with swsusp
after i resume from S4 , my clock is still at the time when it was suspended.You should use something like:
hwclock --systohc
echo -n "1 0 0" >/proc/sys/kernel/swsusp
sleep 5 # time to sleep
hwclock --hctosysQuoted 4 lines
the secound thing is that i need to rmmod my 8139too Realtek eth0 chip and reinsert it by hand . although i get the correct messages at resume : " setting up half dupley 10/100 ...."
Quoted 9 lines
Quoted 3 lines
Anybody has a hint ...?
Now I haven't my swsusp script at hand. I'll send it as soon as I come back home. The concept is to rmmod modules or stop services before susp. and insmod restart they after wakeup.
may you can sent me this script .. since i dont manage it to do !!?!?!
Quoted 6 lines
--
Regards, Marco Gigante
Signature · 23 lines
_____________________________________ *Robert Wörle Linux | Embedded Device* * Symplon AG* *...touch the internet* phone: +49 89 552 999 35 fax: +49 89 552 999 10 email: [email protected] <mailto:[email protected]> web: www.symplon.com <http://www.symplon.com/> _____________________________________ ------------------------------------------------------- This SF.NET email is sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab