2.5.36: PCI: Unable to reserve I/O region
Hi,
just booted 2.5.36-mm1. The following part from dmesg appeared a little strange or rather wrong to me. The systems runs fine as far as I can see.
ide1 at 0x170-0x177,0x376 on irq 15
ICH: IDE controller at PCI slot 00:1f.1
PCI: Unable to reserve I/O region #5:10@f000 for device 00:1f.1
ICH: not 100% native mode: will probe irqs later
ICH: port 0x01f0 already claimed by ide0
ICH: port 0x0170 already claimed by ide1
ICH: neither IDE port enabled (BIOS)
Are these messages bad?
Best regards,
Axel
Linux prester 2.5.36-mm1 #0 Wed Sep 18 17:38:19 CEST 2002 i686 unknown
Gnu C gcc (GCC) 3.2.1 20020915 (prerelease) Copyright (C)
2002
Free Software Foundation, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Gnu make 3.79.1 util-linux 2.11r mount 2.11r modutils 2.4.19 e2fsprogs 1.27 PPP 2.4.1 Linux C Library 2.2.5 Dynamic linker (ldd) 2.2.5 Procps 2.0.8 Net-tools 1.60 Kbd 1.06 Sh-utils 2.0 Modules Loaded 8250 core rtc nls_iso8859-1 nls_cp437 minix
00:00.0 Host bridge: Intel Corp. 82810 GMCH [Graphics Memory Controller Hub] (rev 03)
Subsystem: Intel Corp. 82810 GMCH [Graphics Memory Controller Hub]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
00:01.0 VGA compatible controller: Intel Corp. 82810 CGC [Chipset Graphics Controller] (rev 03) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80 [Master])
Subsystem: Intel Corp. 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at f000 [size=16]00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp. 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d000 [size=32]
00:1f.5 Multimedia audio controller: Intel Corp. 82801AA AC'97 Audio (rev
02)
Subsystem: Analog Devices: Unknown device 5348
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc00 [size=64]Quoted 14 lines · [email protected] wrote:
Hi,
just booted 2.5.36-mm1. The following part from dmesg appeared a little strange or rather wrong to me. The systems runs fine as far as I can see.
ide1 at 0x170-0x177,0x376 on irq 15
ICH: IDE controller at PCI slot 00:1f.1
PCI: Unable to reserve I/O region #5:10@f000 for device 00:1f.1
ICH: not 100% native mode: will probe irqs later
ICH: port0x01f0already claimed by ide0
ICH: port0x0170already claimed by ide1
ICH: neither IDE port enabled (BIOS)
Quoted 2 lines
Are these messages bad?
I get them too. Part of the recent IDE changes. Apparently they are expected, and OK.
Quoted 2 lines · Andrew Morton
I get them too. Part of the recent IDE changes. Apparently they are expected, and OK.
Still suprised. Do you get them in 2.4.20-pre7-ac1 ?