net driver series 11
Subsystems (2)
Marcelo, please do a
bk pull http://gkernel.bkbits.net/net-drivers-2.4
This will update the following files:
Documentation/networking/e100.txt | 99 ++++------ Documentation/networking/e1000.txt | 22 +- drivers/net/e100/e100.h | 8 drivers/net/e100/e100_main.c | 220 ++++++++--------------- drivers/net/e100/e100_proc.c | 22 +- drivers/net/e1000/e1000.h | 10 + drivers/net/e1000/e1000_ethtool.c | 29 --- drivers/net/e1000/e1000_hw.c | 56 ++++- drivers/net/e1000/e1000_hw.h | 33 ++- drivers/net/e1000/e1000_main.c | 167 +++++++++++------ drivers/net/e1000/e1000_osdep.h | 2 drivers/net/e1000/e1000_param.c | 105 +++++------ drivers/net/e1000/e1000_proc.c | 30 +-- drivers/net/eepro100.c | 349 +++++++++++++++++++------------------ drivers/net/ewrk3.c | 320 ++++++++++++++++++++++++++++----- drivers/net/mii.c | 11 - drivers/net/natsemi.c | 6 drivers/net/pcnet32.c | 36 +++ 18 files changed, 892 insertions(+), 633 deletions(-)
through these ChangeSets:
<[email protected]> (02/10/23 1.746.1.5)
drivers/net/eepro100.c: set phy_id_mask and reg_num_mask in mii_if
<[email protected]> (02/10/23 1.746.1.4)
drivers/net/mii.c: fix flipped logic
<[email protected]> (02/10/23 1.746.1.3)
drivers/net/eepro100.c: set the PHY ID correctly
<[email protected]> (02/10/21 1.749.1.7)
Add link status checking to pcnet32 net driver
<[email protected]> (02/10/21 1.749.1.5)
Last ewrk3 for now. Updates the changelog to cover previous patches, bumps the revision number, and replaces the horrific EthwrkSignature function with something (slightly) less horrific.
<[email protected]> (02/10/21 1.749.1.4)
This patch adds some locking fixups to the ewrk3 ioctl routine. None of these are critical since the ioctls AFAIK are used only by the EEPROM config utility.
<[email protected]> (02/10/21 1.749.1.3)
Remove cli/sti from ewrk3 net driver.
Also, comment out ETHTOOL_PHYS_ID until its sleeping is fixed.
Originally by Denis Vlasenko, then via Adam Kropelin, and finally cleaned up by me.
<[email protected]> (02/10/21 1.746.1.2)
drivers/net/eepro100.c: cleanup messages that pop up since netif_msg_xxx change
<[email protected]> (02/10/21 1.749.1.2)
The following patch adds support for ethtool to the ewrk3 driver. It is against 2.5-BK but should apply to any recent 2.5 and 2.4 as well. In addition to adding ethtool support, it also removes the cli/sti fixup attribution from the changelog since that didn't actually go in yet and fixes a small style issue I introduced in the multi-card support patch.
This has been tested on an SMP x86 box containing 3 DE205 NICs.
<[email protected]> (02/10/18 1.742.1.18)
e100 5/5:
* updates to Documentation/networking/e100.txt
<[email protected]> (02/10/18 1.742.1.17)
e100 4/5:
* Updated change log
* Adding notifier to track ifname change for /proc info
<[email protected]> (02/10/18 1.742.1.16)
e100 3/5:
* Added meaningful message for self-test failures
* Removed confusing messages from probe when link isn't detected
<[email protected]> (02/10/18 1.742.1.15)
e100 2/5:
* Remove broken home-grown Rx polling mode (make way for NAPI)
<[email protected]> (02/10/18 1.742.1.14)
e100 1/5:
* C99 struct initializer format
<[email protected]> (02/10/18 1.742.1.13)
e1000 11/11:
* Documentation/networking/e1000.txt updates
<[email protected]> (02/10/18 1.742.1.12)
e1000 10/11:
* C99 struct initializer format
<[email protected]> (02/10/18 1.742.1.11)
e1000 9/11:
* Added bullets to changelog
* Whitespace cleanup
<[email protected]> (02/10/18 1.742.1.10)
e1000 8/11:
* Forcing 1000/fd is easier to undo with ethtool
* Adapters supporting WoL capabilities are now an inclusive versus exclusive list
<[email protected]> (02/10/18 1.742.1.9)
e1000 7/11:
* Added software interrupt to ensure rx ring is cleaned in case of previous allocation failures
* Filled netdev->mem_end member
<[email protected]> (02/10/18 1.742.1.8)
e1000 6/11:
* Adding notifier to track ifname change for /proc info
<[email protected]> (02/10/18 1.742.1.7)
e1000 5/11:
* 2/3 wire downshift phy bits changed in newer phy revs
<[email protected]> (02/10/18 1.742.1.6)
e1000 4/11:
* Newer controllers required manual phy PM enable for WoL to work
<[email protected]> (02/10/18 1.742.1.5)
e1000 3/11:
* Set interrupt delay timer default to 0 across all adapters
<[email protected]> (02/10/18 1.742.1.4)
e1000 2/11:
* Changed flow control defaults to minimize packet drops
<[email protected]> (02/10/18 1.742.1.3)
e1000 1/11:
* add new pci ids
<[email protected]> (02/10/17 1.742.1.2)
drivers/net/eepro100.c: eliminate speedo_intrmask
<[email protected]> (02/10/17 1.737.3.8)
drivers/net/eepro100.c: compile bugs
<[email protected]> (02/10/16 1.737.3.7)
drivers/net/natsemi.c: init msg_enable in proper way
<[email protected]> (02/10/16 1.737.3.6)
drivers/net/eepro100.c: mask the interrupt and do a small delay on close()
<[email protected]> (02/10/16 1.737.3.5)
drivers/net/eepro100.c: only set priv->last_rx_time if we did work
<[email protected]> (02/10/16 1.737.3.4)
drivers/net/eepro100.c: simplify wait_for_cmd_done(), better errors
<[email protected]> (02/10/16 1.737.3.3)
drivers/net/eepro100.c:
* use netif_msg_xxx() instead of speedo_debug
* better default debug mask, proper use of debug module param
* add ETHTOOL_[GS]MSGLVL
<[email protected]> (02/10/14 1.737.3.2)
drivers/net/mii.c: only call netif_carrier_{on,off} if there is a state change
<[email protected]> (02/10/14 1.737.3.1)
drivers/net/eepro100.c:
* mii cleanups
* use mii_check_link()
* check link every timer