Skip to contentSkip to conversation

VIA vt8235 headache

DISCUSSION sven kissner 2 participants 2 messages Feb 5, 2003 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

hi petr,

i had the same errors (although i never experienced any issues with hd, but this seems to be because i'm running them on primary while having my atapu devices on secondary). i fixed them the following:

- using 2.4.21pre4 (pre3 worked either)
- applying the following patch from vojteck:

<--
[email protected], 2002-12-19 11:23:11+01:00, [email protected]
VIA IDE: Always use slow address setup timings for ATAPI devices.

via82cxxx.c | 19 ++++++-------------

1 files changed, 6 insertions(+), 13 deletions(-)
drivers/ide/pci/via82cxxx.c Thu Dec 19 11:23:42 2002 +0 -0
diff -Nru a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c
@@ -1,16 +1,5 @@

/*
- * $Id: via82cxxx.c,v 3.35-ac2 2002/09/111 Alan Exp $
- *
- * Copyright (c) 2000-2001 Vojtech Pavlik
- *
- * Based on the work of:

- *     Michel Aubry
- *     Jeff Garzik
- *     Andre Hedrick

- */
-
-/*
- * Version 3.35
+ * Version 3.36
*
* VIA IDE driver for Linux. Supported southbridges:
*
@@ -152,7 +141,7 @@
via_print("----------VIA BusMastering IDE Configuration"
"----------------");

-       via_print("Driver Version:                     3.35-ac");
+       via_print("Driver Version:                     3.36");

via_print("South Bridge: VIA %s",
via_config->name);

@@ -351,6 +340,10 @@

                 ide_timing_compute(peer, peer->current_speed, &p, T, UT);
                 ide_timing_merge(&p, &t, &t, IDE_TIMING_8BIT);
         }

+
+ /* Always use 4 address setup clocks on ATAPI devices */
+ if (drive->media != ide_disk)
+ t.setup = 4;

         via_set_speed(HWIF(drive)->pci_dev, drive->dn, &t);

-->

keep on rockin'
sven

#2 lore raw

Hi,

with this patch applied over the 2.4.21-pre4-ac2, the CDROM on IDE1 now works ok, no more error messages.

The harddrive on /dev/hdc is still choking though...

hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x00 { }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x00 { }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x00 { }
hdc: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdc: dma_intr: error=0x00 { }
hdc: DMA disabled
ide1: reset: master: error (0x00?)
hdc: lost interrupt

Regards,
Petr

Quoted 59 lines · sven kissner

hi petr,

i had the same errors (although i never experienced any issues with hd, but this seems to be because i'm running them on primary while having my atapu devices on secondary). i fixed them the following:

- using 2.4.21pre4 (pre3 worked either)
- applying the following patch from vojteck:

<--
[email protected], 2002-12-19 11:23:11+01:00, [email protected]
VIA IDE: Always use slow address setup timings for ATAPI devices.

via82cxxx.c | 19 ++++++-------------

1 files changed, 6 insertions(+), 13 deletions(-)

diff -Nru a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c

drivers/ide/pci/via82cxxx.c Thu Dec 19 11:23:42 2002 +6 -14
@@ -1,16 +1,5 @@
 /*
- * $Id: via82cxxx.c,v 3.35-ac2 2002/09/111 Alan Exp $
- *
- *  Copyright (c) 2000-2001 Vojtech Pavlik
- *
- *  Based on the work of:
- *     Michel Aubry
- *     Jeff Garzik
- *     Andre Hedrick
- */
-
-/*
- * Version 3.35
+ * Version 3.36
   *
   * VIA IDE driver for Linux. Supported southbridges:
   *
@@ -152,7 +141,7 @@
         via_print("----------VIA BusMastering IDE Configuration"
                 "----------------");
 
-       via_print("Driver Version:                     3.35-ac");
+       via_print("Driver Version:                     3.36");
         via_print("South Bridge:                       VIA %s",
                 via_config->name);
 
@@ -351,6 +340,10 @@
                 ide_timing_compute(peer, peer->current_speed, &p, T, UT);
                 ide_timing_merge(&p, &t, &t, IDE_TIMING_8BIT);
         }
+
+       /* Always use 4 address setup clocks on ATAPI devices */
+       if (drive->media != ide_disk)
+               t.setup = 4;
 
         via_set_speed(HWIF(drive)->pci_dev, drive->dn, &t);
-->