Skip to contentSkip to conversation

linuxppc_2_4_devel Spruce KGDB patch

PATCH Mark A. Greer 1 participant 1 message Feb 8, 2003

lore
Share & tools
lore
#0 lore raw

If no one objects to this patch, would a power that be please push it.

Mark
--

===== arch/ppc/config.in 1.165 vs edited =====

arch/ppc/config.in +7 -1
@@ -225,6 +225,11 @@
   define_bool CONFIG_EPIC_SERIAL_MODE y
 fi
 
+if [ "$CONFIG_SPRUCE" = "y" ]; then
+  define_bool CONFIG_GEN550_KGDB y
+  define_bool CONFIG_GEN550_PROGRESS y
+fi
+
 if [ "$CONFIG_LOPEC" = "y" ]; then
   define_bool CONFIG_EPIC_SERIAL_MODE y
   define_bool CONFIG_GEN550_KGDB y
@@ -756,7 +761,8 @@
 if [ "$CONFIG_MCPN765" = "y" -o "$CONFIG_SANDPOINT" = "y" \
 	-o "$CONFIG_ZX4500" = "y" -o "$CONFIG_PRPMC800" = "y" \
 	-o "$CONFIG_4xx" = "y" -o "$CONFIG_GT64260" = "y" \
-	-o "$CONFIG_LOPEC" = "y" -o "$CONFIG_PPLUS" = "y" ]; then
+	-o "$CONFIG_LOPEC" = "y" -o "$CONFIG_PPLUS" = "y" \
+	-o "$CONFIG_SPRUCE" = "y" ]; then
   bool 'Support for early boot texts over serial port' CONFIG_SERIAL_TEXT_DEBUG
 fi
 endmenu

===== arch/ppc/configs/spruce_defconfig 1.6 vs edited =====

arch/ppc/configs/spruce_defconfig +47 -2

96 lines not on this page · raw message

===== arch/ppc/kernel/gen550_dbg.c 1.3 vs edited =====

arch/ppc/kernel/gen550_dbg.c +2 -12
@@ -56,7 +56,6 @@
 unsigned long serial_init(int chan, void *ignored)
 {
 	unsigned long com_port;
-	unsigned char lcr, dlm;
 
 	/* We need to find out which type io we're expecting.  If it's
 	 * 'SERIAL_IO_PORT', we get an offset from the isa_io_base.
@@ -80,23 +79,14 @@
 	/* How far apart the registers are. */
 	shift = rs_table[chan].iomem_reg_shift;
 
-	/* save the LCR */
-	lcr = serial_inb(com_port + (UART_LCR << shift));
 	/* Access baud rate */
 	serial_outb(com_port + (UART_LCR << shift), 0x80);
-	dlm = serial_inb(com_port + (UART_DLM << shift));
-	/*
-	 * Test if serial port is unconfigured.
-	 * We assume that no-one uses less than 110 baud or
-	 * less than 7 bits per character these days.
-	 *  -- paulus.
-	 */
 
 	/* Input clock. */
 	serial_outb(com_port + (UART_DLL << shift),
-			(BASE_BAUD / SERIAL_BAUD) & 0xFF);
+			(rs_table[chan].baud_base / SERIAL_BAUD) & 0xFF);
 	serial_outb(com_port + (UART_DLM << shift),
-			(BASE_BAUD / SERIAL_BAUD) >> 8);
+			(rs_table[chan].baud_base / SERIAL_BAUD) >> 8);
 	/* 8 data, 1 stop, no parity */
 	serial_outb(com_port + (UART_LCR << shift), 0x03);
 	/* RTS/DTR */

===== arch/ppc/platforms/spruce_setup.c 1.2 vs edited =====

arch/ppc/platforms/spruce_setup.c +84 -49

169 lines not on this page · raw message