Skip to contentSkip to conversation

XFBB Nightmares!

DISCUSSION Bill Walton 4 participants 5 messages Mar 18, 2003 – Mar 19, 2003 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

Nobody on the XFBB mailing list seemed to be interested in answering my questions. Would anyone here on the linux-hams mailing list care to comment on my concerns listed below? Have all of you installed XFBB without a single problem? Could I be living on top of an Indian Burial Ground or something? I would certainly like to move on to the next set of error codes if someone would be kind enough to comment on my current dilemma.

Thank you in advance for your expert advice and support!

Regards,

Bill KJ6EO

(copy of message sent to [email protected] mailing list)

Gentlemen -

Thank you for taking the time to read my message. I have finally resolved my AX25 and Linuxnode problems and I am ready to tackle my final problem XFBB. Everyone else seems to have little or no problems getting XFBB running. So, I must assume that I am overlooking some menial information that is keeping my XFBB setup from working. The README file is simple and clear and I have followed the steps:

(FYI) ... I am running RedHat v7.2 with a 2.4.20 kernel. AX25 and Linuxnode installed.

1)    Put tarball in a specific directory
2)    un-tar it
3)    Run the install shell and answer the questions
4)    Edit the appropriate files ... port.sys, init.srv, etc.
5)    Run it ... execute the program shell ... ./xfbb.sh

However ... the result is always the same "Unknown return value 127". I have heard rumors that XFBB has to be compiled. There are no instructions with my tarball that says it has to be compiled (x700e_full.tgz). If I am missing the compile step I would appreciate it if someone would point me in the right direction. Is it possible that I have the wrong tarball? I have been stuck with the "unknown return value 127" error for ever. It would be nice to at least move on to the next set of error codes.

Any information that you might be able to offer would be appreciated!

Regards,

Bill KJ6EO

#1 lore raw
Quoted 8 lines

However ... the result is always the same "Unknown return value 127". I have heard rumors that XFBB has to be compiled. There are no instructions with my tarball that says it has to be compiled (x700e_full.tgz). If I am missing the compile step I would appreciate it if someone would point me in the right direction. Is it possible that I have the wrong tarball? I have been stuck with the "unknown return value 127" error for ever. It would be nice to at least move on to the next set of error codes.

Bill:

Looking at the "fbb" script, there's a loop which restarts fbb if it exits. Inside this loop, if one of the commands fails somehow, the script emits the message you report. Based on the code in the loop, the code comes from the shell, and the value of 127 means a command wasn't found. It looks to me like the xfbbd command is the one which isn't found. I suggest you check the definitions at the top of the fbb script to make sure they are correct.

Dennis Boone
KB8ZQZ

#2 lore raw
In reply to Bill Walton

Maybe the xfbb list has been a bit slow lately or I've been kicked off again.

Quoted 1 line

(FYI) ... I am running RedHat v7.2 with a 2.4.20 kernel. AX25 and

Running on RH7.2 here too. Using a 2.2 kernel, but shouldn't matter.

Quoted 1 line

Any information that you might be able to offer would be appreciated!

rpm -ivh xfbb-7.04-2.i386.rpm works for me.

Signature · 4 lines
Shane Deering                   Sent using Kmail v1.4.3
[email protected]                  on Mandrake Linux, the Desktop OS
vk3bvp@vk3bvp.#sev.vic.aus.oc   MDK9.0 Up 5 hours and 15 minutes 
http://www.qsl.net/vk3bvp/      RH7.2 Up 17 days, 15 hours and 40 minutes 

A message that is not in the archive (sent off-list or not yet received): [email protected]

#4 lore raw
Quoted 11 lines

Thank you for answering my message. My base directory is /usr/src/fbb. When the shell tries to execute the executable "xfbb", I get this message just before I get the unknown return value 127 error:

/usr/src/fbb/bin/xfbb:no such file or directory

In the above directory I do see the file "xfbb". If I try to execute it from the directory that it resides in /usr/src/fbb/bin I get a "no such file" error message. The xfbb file must be linked to something preventing me and the shell from executing it.

Bill:

It sounds like the package you obtained is broken somehow. The package file name you mentioned does not seem to be a source package, and the installation instructions sound like a binary package of some sort. My (Debian) package doesn't include a binary called xfbb; I do have xfbbd and xfbbC.

Given that, and the fact that there are newer versions available, I wonder if the easiest thing to do might be to grab a different binary package. There's an RPM version of 7.04 on the download page at:

http://www.f6fbb.org/versions.html

The URL for that file directly is:

    ftp://ftp.f6fbb.org/pub/f6fbb/distrib/linux/packages/redhat/xfbb-7.04-2.i386.rpm

If you really want to try to untangle the one you have, or if the RPM is balky for some reason, we can dig further.

De

#5 lore raw
Quoted 5 lines · Dennis Boone

It sounds like the package you obtained is broken somehow. The package file name you mentioned does not seem to be a source package, and the installation instructions sound like a binary package of some sort. My (Debian) package doesn't include a binary called xfbb; I do have xfbbd and xfbbC.

It's probably not broken. It's just so old that the binary is linked against a very old version of libc (libc5). Not having this lib installed causes a somewhat misleading error message when one tries to execute the binary. Some of the modern distributions might still have a compatibility package for libc5 but it's probably not installed by default.

Anyway, I would recommend installing a newer version of xfbb. There are binary packages available as people have already pointed out.

This is becoming a FAQ. I think Jean-Paul should do himself a favor and remove the old binary packages from his web site... :)

Signature · 3 lines
Tomi Manninen           Internet:  [email protected]
OH2BNS                  AX.25:     [email protected]
KP20ME04                Amprnet:   [email protected]