Skip to contentSkip to conversation

Problems with PM826 card

DISCUSSION bhavin 2 participants 4 messages Sep 4, 2003

lore
Share & tools
lore

bhavin

author
#0 lore raw

Hello All,

I am using a PM826 card with our own developed carrier extension
board. I have build the ppcboot image. I am booting the image from flash and through serial communication SCC and I have configured the correct serial channel number from our card's schematics. Now, the ppcboot works but, when I try to write something in flash through ppcboot (either 'loadb' command or 'nm' command) the flash contents are not getting changed. All other functionality of ppcboot works like erase, read, etc. but all the functionality related to 'write to flash' is not working. Can any one please suggest me what could be the possible reason??

Also, I have one separate program which, I downloaded from somewhere which does some read/write operation to the PM826 card's flash. Through that program the writing is working perfect.

Has it something to do with ppcboot configuration or the addressing mode? Your help will be highly appreciated.

Thanks & Regards,
Bhavin Shah
Embedded Engineer
eInfochips Ltd.,
[email protected]

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw

Dear Bhavin,

Quoted 3 lines · in message <[email protected]> you wrote:

I am using a PM826 card with our own developed carrier extension
board. I have build the ppcboot image. I am booting the image from flash

Please upgrade. PPCBoot is pretty old, and a lot of modifications have been added lately. Please use a recent version of U-Boot instead (0.4.7).

Quoted 4 lines

and through serial communication SCC and I have configured the correct serial channel number from our card's schematics. Now, the ppcboot works but, when I try to write something in flash through ppcboot (either 'loadb' command or 'nm' command) the flash contents are not getting

Neither the "loadb" nor "nm" commands can operate directly on flash memory. please download to RAM (or modify the RAM contents) and use the "cp" command to write to flash.

Quoted 2 lines

changed. All other functionality of ppcboot works like erase, read, etc. but all the functionality related to 'write to flash' is not working.

I think all these things are working fine, you are just using them wrong.

Quoted 1 line

Can any one please suggest me what could be the possible reason??

Read the documentation; see
http://www.denx.de/twiki/bin/view/DULG/Manual

Quoted 3 lines

Also, I have one separate program which, I downloaded from somewhere which does some read/write operation to the PM826 card's flash. Through that program the writing is working perfect.

It's working perfectly in PPCBoot and U-Boot, too. Just remember that
the command to write to flash is "cp" (and it's variants
"cp.{l|w|b}").

Quoted 1 line

Has it something to do with ppcboot configuration or the addressing mode?

No, it is a user error.

Best regards,

Wolfgang Denk

--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] Software suppliers are trying to make their software packages more ``user-friendly''. . . . Their best approach, so far, has been to take all the old brochures, and stamp the words, ``user-friendly'' on
the cover. - Bill Gates

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

author
#2 lore raw

Hello,

Thanks a bunch for your guidance. It helped a lot. I was able to
download my Linux image to memory and in flash memory after through cp. But in both the cases when I tried to boot my linux, the setup got restarted after giving the message

Quoted 1 line

bootm 100000

## Booting image at 00100000 ...
Image Name: 2.4.5-pre1 initrd for
PM826
Created: 2003-09-04 13:43:13
UTC
Image Type: PowerPC Linux Kernel Image
(gz
Data Size: 516901 Bytes = 504 kB = 0
MB
Load Address: 00000000
Entry Point: 0000000c
Verifying Checksum ... OK
Uncompressing Kernel Image ...

Could any one please help me what could be the possible problem as I am totally new to this area. Or If I can get some pointer on where to look for this trouble It would be a great help.

Thanks & Regards,
Bhavin Shah
Embedded Engineer
eInfochips Ltd.,
[email protected]

Quoted 70 lines · Wolfgang Denk

Dear Bhavin,

Quoted 4 lines · in message <[email protected]> you wrote:

I am using a PM826 card with our own developed carrier extension
board. I have build the ppcboot image. I am booting the image from flash

Please upgrade. PPCBoot is pretty old, and a lot of modifications have been added lately. Please use a recent version of U-Boot instead (0.4.7).

Quoted 6 lines

and through serial communication SCC and I have configured the correct serial channel number from our card's schematics. Now, the ppcboot works but, when I try to write something in flash through ppcboot (either 'loadb' command or 'nm' command) the flash contents are not getting

Neither the "loadb" nor "nm" commands can operate directly on flash memory. please download to RAM (or modify the RAM contents) and use the "cp" command to write to flash.

Quoted 4 lines

changed. All other functionality of ppcboot works like erase, read, etc. but all the functionality related to 'write to flash' is not working.

I think all these things are working fine, you are just using them wrong.

Quoted 3 lines

Can any one please suggest me what could be the possible reason??

Read the documentation; see
http://www.denx.de/twiki/bin/view/DULG/Manual

Quoted 5 lines

Also, I have one separate program which, I downloaded from somewhere which does some read/write operation to the PM826 card's flash. Through that program the writing is working perfect.

It's working perfectly in PPCBoot and U-Boot, too. Just remember that
the command to write to flash is "cp" (and it's variants
"cp.{l|w|b}").

Quoted 3 lines

Has it something to do with ppcboot configuration or the addressing mode?

No, it is a user error.

Best regards,

Wolfgang Denk

Quoted 11 lines

--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] Software suppliers are trying to make their software packages more ``user-friendly''. . . . Their best approach, so far, has been to take all the old brochures, and stamp the words, ``user-friendly'' on
the cover. - Bill Gates

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#3 lore raw

Dear Bhavin,

Quoted 5 lines · in message <[email protected]> you wrote:

Thanks a bunch for your guidance. It helped a lot. I was able to
download my Linux image to memory and in flash memory after through cp. But in both the cases when I tried to boot my linux, the setup got restarted after giving the message

And again this is a user error which could have been avoided had you read the documentation (like the README that comes with U-Boot).

Quoted 1 line
   Image Name:   2.4.5-pre1 initrd for PM826

I recommend NOT to attempt to use a 2.4.5-pre1 kernel. The PM826 board is supported by our 2.4.4 and 2.4.20 kernel trees. 2.4.5-pre1 will most likely NOT run.

Quoted 2 lines
   Load Address: 00000000
   Entry Point:  0000000c

Also, for all 2.4.x kernels the entry point address is 0x0000.

Quoted 3 lines

Could any one please help me what could be the possible problem as I am totally new to this area. Or If I can get some pointer on where to look for this trouble It would be a great help.

If you are new you should probably start using tested components, like our 2.4.4 or 2.4.20 kernel trees instead of completely untested 2.4.5-pre1. See also http://www.denx.de/re/linux.html

Best regards,

Wolfgang Denk

--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] "Plan to throw one away. You will anyway."
- Fred Brooks, "The Mythical Man Month"

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/