Skip to contentSkip to conversation

DINK32 R13.1 on Sandpoint X2

DISCUSSION Yuxiao Xi 2 participants 2 messages Sep 4, 2003

lore
Share & tools
lore

Yuxiao Xi

author
#0 lore raw

Hi,Tom,
From the mailing lists,I know that someone use DINK32's tftp
download function to download his image successfully on a Sandpoint X3 board.Is there any important differences between Sandpoint X3 and X2 board so that I can not use the DINK32's tftp function on X2 board?

======= 2003-09-03 11:04:00 ��=======

Quoted 11 lines · Yuxiao Xi
Quoted 5 lines

Now I'm working on a Motorola Sandpoint X2 board with ppc8240.
I use DINK32 r13.1 to boot my linux kernel image. From DINK32 r13.1 user manual,I know that DINK32 r13.1 supports ethernet card Realtek 8139,but after these steps:

What I would suggest is that instead of using the ethernet card support, you use the serial support still. DINK32 r13.0.0 and newer support 115200 baud, so loading a kernel via serial is now much less painful than it used to be.

= = = = = = = = = = = = = = = = = = = =

����������������Yuxiao Xi
����������������[email protected]
��������������������2003-09-04

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw

We have an 8139 and have successfully downloaded and run a kernel with DINK version 13.1.1. I didn't do it but the instructions sent from the person who did are:

To download via the network, DINK uses fixed IP address and Realtek8139 NIC. The steps are:

1. do "ppr" verify NIC card has been identified vendor/device ID as 10EC/8139
2. do "env IO=COM1:9600@100, Then "reset".
3. do "ni -i " to set up your network parameters. For example:

    DINK32[MPC7457] {1} >>ni
    NETWORK INFORMATION
      PCI CARD
        Type 8139/10EC on slot 16

      SETTINGS
        SERVER(TFTP) : 192.168.  1.  1
        GATEWAY      : 192.168.  1.  1
        NETMASK      : 255.255.255.  0
        DHCP         : 192.168.  1.  1
        CLIENT(DINK) : 192.168.  1.  7

      DHCP: Disabled
      SESSION TIMEOUT: Never

4. set up you tftp server at host side
5. The download command is "dl -nw -b -o800000 -fzImage.sandpoint"
6. "go 810000"

You can change IP addr, image name, to fit your setup.

As far as differences in the X2 vs. X3, yes there are important differences. Does DINK v13.1.1 run successfully & download via the network successfully on an X2? I don't know, you'll have to figure that out for yourself or talk to Motorola.

Mark
--

Quoted 6 lines · Yuxiao Xi

Hi,Tom,
From the mailing lists,I know that someone use DINK32's tftp
download function to download his image successfully on a Sandpoint X3 board.Is there any important differences between Sandpoint X3 and X2 board so that I can not use the DINK32's tftp function on X2 board?

Quoted 20 lines

======= 2003-09-03 11:04:00 £º=======

Quoted 16 lines · Yuxiao Xi
Quoted 9 lines

Now I'm working on a Motorola Sandpoint X2 board with ppc8240.
I use DINK32 r13.1 to boot my linux kernel image. From DINK32 r13.1 user manual,I know that DINK32 r13.1 supports ethernet card Realtek 8139,but after these steps:

What I would suggest is that instead of using the ethernet card support, you use the serial support still. DINK32 r13.0.0 and newer support 115200 baud, so loading a kernel via serial is now much less painful than it used to be.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/