Skip to contentSkip to conversation

PCI probe, please CC [email protected]

DISCUSSION Kendrick Hamilton 2 participants 4 messages Sep 15, 2003 – Sep 16, 2003

lore
Share & tools
lore
#0 lore raw

Hello,
we are using the Linux 2.2.16 kernel (some of the code we purchased
does not work with 2.4.x kernels and we would have to do a lot of regression testing to upgrade) on an IBM e-server. We wrote a module for a modulator card we are using. The code uses pci_find_device to find the modulator cards. The problem we are having is that it finds the cards in different orders. One time hss0 is the card in slot 4 and hss1 is the card in slot5. The next time we power up the computer, hss0 is the card in slot5 and hss1 is the card in slot 4.
The IBM e-server has about 5 PCI bridges.
Do you have any suggestion as to how I might be able to ensure the
cards are always detected in the same order? Our system requires that they always be in the same order.
I can email you the source code for our module, it is GPLed.

Please CC comments to [email protected]
TIA,
Kendrick Hamilton

#1 lore raw
Quoted 5 lines · Kendrick Hamilton

Hello,
we are using the Linux 2.2.16 kernel (some of the code we purchased
does not work with 2.4.x kernels and we would have to do a lot of regression testing to upgrade) on an IBM e-server. We wrote a module for a modulator card we are using. The code uses pci_find_device to find the

Quoted 8 lines

modulator cards. The problem we are having is that it finds the cards in different orders. One time hss0 is the card in slot 4 and hss1 is the card in slot5. The next time we power up the computer, hss0 is the card in slot5 and hss1 is the card in slot 4.
The IBM e-server has about 5 PCI bridges.
Do you have any suggestion as to how I might be able to ensure the
cards are always detected in the same order? Our system requires that they always be in the same order.

Are the pci device ids different across different boots? If not, is there any way you can tie a specific device to a specific interface (unique hardware addresses, mac addresses, etc.)?

thanks,

greg k-h

#2 lore raw

Greg,
We don't have a hardware address to use. What I am looking for is a
way to tie it to the slot number. Is there any way of getting the slot number? Kendrick

PS. I just subscribed to the linux kernel mailing list so I don't need the CC [email protected] anymore.

Quoted 21 lines · Greg KH
Quoted 8 lines · Kendrick Hamilton

Hello,
we are using the Linux 2.2.16 kernel (some of the code we purchased
does not work with 2.4.x kernels and we would have to do a lot of regression testing to upgrade) on an IBM e-server. We wrote a module for a modulator card we are using. The code uses pci_find_device to find the modulator cards. The problem we are having is that it finds the cards in different orders. One time hss0 is the card in slot 4 and hss1 is the card in slot5. The next time we power up the computer, hss0 is the card in slot5 and hss1 is the card in slot 4.
The IBM e-server has about 5 PCI bridges.
Do you have any suggestion as to how I might be able to ensure the
cards are always detected in the same order? Our system requires that they always be in the same order.

Are the pci device ids different across different boots? If not, is there any way you can tie a specific device to a specific interface (unique hardware addresses, mac addresses, etc.)?

thanks,

greg k-h

#3 lore raw
Quoted 4 lines · Kendrick Hamilton

Greg,
We don't have a hardware address to use. What I am looking for is a
way to tie it to the slot number. Is there any way of getting the slot number?

Again, do the pci bus ids change between boots?

And no, there usually is not a way to get to the slot number, except for machines that happen to have a pci hotplug controller. They usually have some way to map from the slot to the pci devices.

thanks,

greg k-h