Skip to contentSkip to conversation

2.6.0 keyboard not working

DISCUSSION Lennert Buytenhek 4 participants 9 messages Dec 18, 2003

lore
Share & tools
lore
#0 lore raw

Hi,

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Ideas?

thanks,
Lennert

#1 lore raw
Quoted 11 lines · Lennert Buytenhek

Hi,

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Ideas?

May we have a look at your .config?

ta,
Zwane

#2 lore raw

hrm. I was having the same problems with both my usb keyboard and mouse. i figure I just missed something. haven't gotten around to looking too much into it though.
maybe in the morning.

Quoted 25 lines · Zwane Mwaikambo
Quoted 11 lines · Lennert Buytenhek

Hi,

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Ideas?

May we have a look at your .config?

ta,
Zwane
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#3 lore raw
In reply to Zwane Mwaikambo
Quoted 7 lines · Zwane Mwaikambo
Quoted 7 lines

Hi,

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Quoted 6 lines
Quoted 4 lines

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Ideas?

May we have a look at your .config?

It's attached in .gz format (sorry, it wouldn't go through otherwise :/).

--L

#4 lore raw
Quoted 7 lines · buytenh
Quoted 7 lines
Quoted 7 lines

Hi,

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Ideas?

May we have a look at your .config?

It's attached in .gz format (sorry, it wouldn't go through otherwise :/).

OK, I'm an idiot.. attached this time.

--L

#5 lore raw
Quoted 11 lines · Lennert Buytenhek
Quoted 11 lines
Quoted 11 lines
Quoted 9 lines

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Ideas?

May we have a look at your .config?

Thanks Lennert, could you try without CONFIG_HIGHMEM64G, perhaps just CONFIG_HIGHMEM4G, how much memory in the system? dmesg also would be nice.

#6 lore raw

Zwane Mwaikambo([email protected]) on 2003.12.18 11:30:27 +0000:

Quoted 10 lines · Lennert Buytenhek
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines

Halfway between having uncompressed the kernel and starting init, the console starts to scroll "atkbd.c: Unknown key pressed", mentioning key code 0 (IIRC), even though no keys are pressed at all. After a while, the scrolling stops, but the keyboard still doesn't work. 2.4 works fine on the same hardware.

Hardware is an Intel SE7505VB2 board with dual 2.40GHz Xeon processors, and a Logitech PS/2 "Internet keyboard."

Quoted 6 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line

Ideas?

May we have a look at your .config?

Thanks Lennert, could you try without CONFIG_HIGHMEM64G, perhaps just CONFIG_HIGHMEM4G, how much memory in the system? dmesg also would be nice.

I had exactly the same symptoms (Unknown key pressed, scrolling) with a Cherry PS/2 keyboard an a PS/2 mouse, starting with 2.6.0-test6 (i think). The mouse also stopped working.

Unfortunatly it was a heisenbug - every time i tried to find out what caused the problem (there where drivers/input/mouse* - changes at that time) the problem disapeared. I then exchanged the mouse for a USB-type and the problem disappeared completly.

/B.

Signature · 5 lines
Sebastian Benoit <[email protected]>
My mail is GnuPG signed -- Unsigned ones are bogus -- http://www.gnupg.org/
GnuPG 0xD777DBA7 2003-09-10 D02B D0E0 3790 1AA1 DA3A  B508 BF48 87BF D777 DBA7

Konzepte sind Kokolores. -- Erich Ribbeck
#7 lore raw
In reply to Zwane Mwaikambo
Quoted 2 lines · Zwane Mwaikambo

Thanks Lennert, could you try without CONFIG_HIGHMEM64G, perhaps just CONFIG_HIGHMEM4G, how much memory in the system? dmesg also would be nice.

Hi Zwane, I just finished checking, and without highmem and with HIGHMEM4G it works just fine, only with 64G I get the 'Unknown key pressed' flood which I described. I had 64G on because I copied my .config from Arjan's 2.6 RPMs, none of which worked on this machine because of those keyboard troubles. The box has 1G of RAM.

Thanks! Anything else I can try?

--L

#8 lore raw
Quoted 10 lines · Lennert Buytenhek
Quoted 2 lines · Zwane Mwaikambo

Thanks Lennert, could you try without CONFIG_HIGHMEM64G, perhaps just CONFIG_HIGHMEM4G, how much memory in the system? dmesg also would be nice.

Hi Zwane, I just finished checking, and without highmem and with HIGHMEM4G it works just fine, only with 64G I get the 'Unknown key pressed' flood which I described. I had 64G on because I copied my .config from Arjan's 2.6 RPMs, none of which worked on this machine because of those keyboard troubles. The box has 1G of RAM.

Thanks for testing that, Dan Creswell <[email protected]> mentioned a similar problem with an e7505 Tyan board he has too.

Quoted 1 line

Thanks! Anything else I can try?

I'd love to see dmesg and /proc/iomem for CONFIG_HIGHMEM4G and CONFIG_HIGHMEM64G.