aacraid issues
Subsystems (2)
I have very strange aacraid behavior:
First of all, I know, that aacraid support is experimental, but maybe the issue is related to something else in the kernel.
I have AMD Opteron system with 10 scsi disks, connected to Adaptec 2200S controller, constituting about 1.2TB in total.
I can boot with 2.4.22 kernel, compiled for Xeon, into RedHat 9 (32 bit mode). aacraid version 1.1.2. The raid works great.
Then I boot into SuSE Linux 9 for the Opterons, with 2.4.23 kernel. aacraid version 1.1-3.
Seems to work, but when I try to access blocks close to the end of the RAID, I am getting I/O errors.
Any ideas?
Where can I get the latest patches for the aacraid driver?
Just tried 2.6.0 kernel with patches for Opteron, but as soon as it starts working with Adaptec controller, it crashes miserably... :-(
Quoted 13 lines · Yaroslav Klyukin
I have very strange aacraid behavior:
First of all, I know, that aacraid support is experimental, but maybe the issue is related to something else in the kernel.I have AMD Opteron system with 10 scsi disks, connected to Adaptec 2200S controller, constituting about 1.2TB in total.
I can boot with 2.4.22 kernel, compiled for Xeon, into RedHat 9 (32 bit mode). aacraid version 1.1.2. The raid works great.
Then I boot into SuSE Linux 9 for the Opterons, with 2.4.23 kernel. aacraid version 1.1-3.
Quoted 9 lines
Seems to work, but when I try to access blocks close to the end of the RAID, I am getting I/O errors.
Any ideas?
Where can I get the latest patches for the aacraid driver?Just tried 2.6.0 kernel with patches for Opteron, but as soon as it starts working with Adaptec controller, it crashes miserably... :-(
Try this, someone else with a 2200 had a similar problem that this patch fixed. It will apply to 2.6.0.
===== drivers/scsi/aacraid/aachba.c 1.20 vs edited =====
drivers/scsi/aacraid/aachba.c +8 -0
@@ -525,6 +525,14 @@if (dev->pae_support !=0 ) {printk (KERN_INFO "%s%d: 64 Bit PAE enabled\n" , dev->name, dev->id);pci_set_dma_mask (dev->pdev, (dma_addr_t )0xFFFFFFFFFFFFFFFFULL ); + }else { +/* +* Reset if Quirk 31 was used, since data +* transfers are ok. +*/ +if (pci_set_dma_mask (dev->pdev,0xFFFFFFFFULL )) { +printk (KERN_INFO "aacraid: Can't reset DMA mask.\n" ); + } }fib_complete (fibptr);
===== drivers/scsi/aacraid/aacraid.h 1.9 vs edited =====
drivers/scsi/aacraid/aacraid.h +2 -0
@@ -529,6 +529,8 @@char * vname;char * model;u16 channels; +int quirks; +#define AAC_QUIRK_31BIT 1 };/*
===== drivers/scsi/aacraid/linit.c 1.22 vs edited =====
drivers/scsi/aacraid/linit.c +48 -28
97 lines not on this page · raw message
Signature · 1 line
Mark Haverkamp <[email protected]>
Quoted 18 lines · Mark Haverkamp
Quoted 16 lines · Yaroslav Klyukin
I have very strange aacraid behavior:
First of all, I know, that aacraid support is experimental, but maybe the issue is related to something else in the kernel.I have AMD Opteron system with 10 scsi disks, connected to Adaptec 2200S controller, constituting about 1.2TB in total.
I can boot with 2.4.22 kernel, compiled for Xeon, into RedHat 9 (32 bit mode). aacraid version 1.1.2. The raid works great.
Then I boot into SuSE Linux 9 for the Opterons, with 2.4.23 kernel. aacraid version 1.1-3.
Seems to work, but when I try to access blocks close to the end of the RAID, I am getting I/O errors.
Any ideas?
Where can I get the latest patches for the aacraid driver?
Quoted 6 lines
Quoted 2 lines
Just tried 2.6.0 kernel with patches for Opteron, but as soon as it starts working with Adaptec controller, it crashes miserably... :-(
Try this, someone else with a 2200 had a similar problem that this patch fixed. It will apply to 2.6.0.
Thank you very much, I will try it tomorrow.
Is there anything for 2.4.23?
Quoted 10 lines
=====
drivers/scsi/aacraid/aachba.c1.20 vs edited =====drivers/scsi/aacraid/aachba.c +0
-0@@ -525,6 +525,14 @@if (dev->pae_support !=0 ) {printk (KERN_INFO "%s%d: 64 Bit PAE enabled\n" , dev->name, dev->id);