Skip to contentSkip to conversation

Add R8A77980/Condor board support

PATCH New Sergei Shtylyov 4 participants 12 messages Feb 16, 2018 – Feb 19, 2018 1 message not in the archive

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v2 cover Add R8A77980/Condor board support

Hello!

Here's the set of 11 patches against Simon Horman's 'renesas.git' repo's 'renesas-devel-20180216-v4.16-rc1' tag. I'm adding the device tree support for the R8A77980-based Condor board (note that NFS root would only work on the Condor boards [re]wired for booting from EtherAVB -- we haven't been able to get the 'sh_eth' driver working in either U-Boot or Linux so far). The necessary SYS-DMAC, [H]SCIF, and EtherAVB bindings updates have been posted, the clock driver has been reposted yesterday, and the merged patches have been dropped from this respin of the series...

[1/5] soc: renesas: rcar-sysc: add R8A77980 support [2/5] arm64: dts: renesas: r8a77980: add [H]SCIF support [3/5] arm64: dts: renesas: r8a77980: add EtherAVB support [4/5] arm64: dts: renesas: initial Condor board device tree [5/5] arm64: dts: renesas: condor: add EtherAVB support

WBR, Sergei

A message that is not in the archive (sent off-list or not yet received): ae31804b-969b-9b20-16d0-50f5dea42f08-M4DtvfQ/[email protected]

#2 lore raw

PATCH v2 1/5 soc: renesas: rcar-sysc: add R8A77980 support

Add support for R-Car V3H (R8A77980) SoC power areas to the R-Car SYSC driver.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- fixed the parents of the A2Rn, A2SCn, A2PDn, and A2CN power domains;
- added Simon's and Geert's tags.

 Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt |    1 
 drivers/soc/renesas/Kconfig                                   |    5 
 drivers/soc/renesas/Makefile                                  |    1 
 drivers/soc/renesas/r8a77980-sysc.c                           |   52 ++++++++++
 drivers/soc/renesas/rcar-sysc.c                               |    3 
 drivers/soc/renesas/rcar-sysc.h                               |    1 
 6 files changed, 63 insertions(+)
Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +1 -0
Index: renesas/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
===================================================================
@@ -18,6 +18,7 @@ Required properties:
       - "renesas,r8a7795-sysc" (R-Car H3)
       - "renesas,r8a7796-sysc" (R-Car M3-W)
       - "renesas,r8a77970-sysc" (R-Car V3M)
+      - "renesas,r8a77980-sysc" (R-Car V3H)
       - "renesas,r8a77995-sysc" (R-Car D3)
   - reg: Address start and address range for the device.
   - #power-domain-cells: Must be 1.
drivers/soc/renesas/Kconfig +5 -0
Index: renesas/drivers/soc/renesas/Kconfig
===================================================================
@@ -15,6 +15,7 @@ config SOC_RENESAS
 	select SYSC_R8A7795 if ARCH_R8A7795
 	select SYSC_R8A7796 if ARCH_R8A7796
 	select SYSC_R8A77970 if ARCH_R8A77970
+	select SYSC_R8A77980 if ARCH_R8A77980
 	select SYSC_R8A77995 if ARCH_R8A77995
 
 if SOC_RENESAS
@@ -60,6 +61,10 @@ config SYSC_R8A77970
 	bool "R-Car V3M System Controller support" if COMPILE_TEST
 	select SYSC_RCAR
 
+config SYSC_R8A77980
+	bool "R-Car V3H System Controller support" if COMPILE_TEST
+	select SYSC_RCAR
+
 config SYSC_R8A77995
 	bool "R-Car D3 System Controller support" if COMPILE_TEST
 	select SYSC_RCAR
drivers/soc/renesas/Makefile +1 -0
Index: renesas/drivers/soc/renesas/Makefile
===================================================================
@@ -13,6 +13,7 @@ obj-$(CONFIG_SYSC_R8A7794)	+= r8a7794-sy
 obj-$(CONFIG_SYSC_R8A7795)	+= r8a7795-sysc.o
 obj-$(CONFIG_SYSC_R8A7796)	+= r8a7796-sysc.o
 obj-$(CONFIG_SYSC_R8A77970)	+= r8a77970-sysc.o
+obj-$(CONFIG_SYSC_R8A77980)	+= r8a77980-sysc.o
 obj-$(CONFIG_SYSC_R8A77995)	+= r8a77995-sysc.o
 
 # Family
drivers/soc/renesas/r8a77980-sysc.c new file +52 -0

52 lines not on this page · raw message

drivers/soc/renesas/rcar-sysc.c +3 -0
Index: renesas/drivers/soc/renesas/rcar-sysc.c
===================================================================
@@ -287,6 +287,9 @@ static const struct of_device_id rcar_sy
 #ifdef CONFIG_SYSC_R8A77970
 	{ .compatible = "renesas,r8a77970-sysc", .data = &r8a77970_sysc_info },
 #endif
+#ifdef CONFIG_SYSC_R8A77980
+	{ .compatible = "renesas,r8a77980-sysc", .data = &r8a77980_sysc_info },
+#endif
 #ifdef CONFIG_SYSC_R8A77995
 	{ .compatible = "renesas,r8a77995-sysc", .data = &r8a77995_sysc_info },
 #endif
drivers/soc/renesas/rcar-sysc.h +1 -0
Index: renesas/drivers/soc/renesas/rcar-sysc.h
===================================================================
@@ -59,6 +59,7 @@ extern const struct rcar_sysc_info r8a77
 extern const struct rcar_sysc_info r8a7795_sysc_info;
 extern const struct rcar_sysc_info r8a7796_sysc_info;
 extern const struct rcar_sysc_info r8a77970_sysc_info;
+extern const struct rcar_sysc_info r8a77980_sysc_info;
 extern const struct rcar_sysc_info r8a77995_sysc_info;
 
 

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

#3 lore raw

PATCH v2 2/5 arm64: dts: renesas: r8a77980: add [H]SCIF support

In reply to Sergei Shtylyov

Describe [H]SCIF ports in the R8A77980 device tree.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- fixed the internal BRG clock to S3D1 for all ports;
- added Geert's tag.

 arch/arm64/boot/dts/renesas/r8a77980.dtsi |  151 ++++++++++++++++++++++++++++++
 1 file changed, 151 insertions(+)
arch/arm64/boot/dts/renesas/r8a77980.dtsi +151 -0
Index: renesas/arch/arm64/boot/dts/renesas/r8a77980.dtsi
===================================================================
@@ -56,6 +56,13 @@
 		method = "smc";
 	};
 
+	/* External SCIF clock - to be overridden by boards that provide it */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
@@ -85,6 +92,150 @@
 			#power-domain-cells = <1>;
 		};
 
+		hscif0: serial at e6540000 {
+			compatible = "renesas,hscif-r8a77980",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6540000 0 0x60>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 520>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x31>, <&dmac1 0x30>,
+			       <&dmac2 0x31>, <&dmac2 0x30>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 520>;
+			status = "disabled";
+		};
+
+		hscif1: serial at e6550000 {
+			compatible = "renesas,hscif-r8a77980",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6550000 0 0x60>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 519>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x33>, <&dmac1 0x32>,
+			       <&dmac2 0x33>, <&dmac2 0x32>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 519>;
+			status = "disabled";
+		};
+
+		hscif2: serial at e6560000 {
+			compatible = "renesas,hscif-r8a77980",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6560000 0 0x60>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 518>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x35>, <&dmac1 0x34>,
+			       <&dmac2 0x35>, <&dmac2 0x34>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 518>;
+			status = "disabled";
+		};
+
+		hscif3: serial at e66a0000 {
+			compatible = "renesas,hscif-r8a77980",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe66a0000 0 0x60>;
+			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 517>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x37>, <&dmac1 0x36>,
+			       <&dmac2 0x37>, <&dmac2 0x36>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 517>;
+			status = "disabled";
+		};
+
+		scif0: serial at e6e60000 {
+			compatible = "renesas,scif-r8a77980",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6e60000 0 0x40>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 207>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x51>, <&dmac1 0x50>,
+			       <&dmac2 0x51>, <&dmac2 0x50>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 207>;
+			status = "disabled";
+		};
+
+		scif1: serial at e6e68000 {
+			compatible = "renesas,scif-r8a77980",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6e68000 0 0x40>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 206>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x53>, <&dmac1 0x52>,
+			       <&dmac2 0x53>, <&dmac2 0x52>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 206>;
+			status = "disabled";
+		};
+
+		scif3: serial at e6c50000 {
+			compatible = "renesas,scif-r8a77980",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6c50000 0 0x40>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 204>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x57>, <&dmac1 0x56>,
+			       <&dmac2 0x57>, <&dmac2 0x56>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 204>;
+			status = "disabled";
+		};
+
+		scif4: serial at e6c40000 {
+			compatible = "renesas,scif-r8a77980",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6c40000 0 0x40>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 203>,
+				 <&cpg CPG_CORE 19>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x59>, <&dmac1 0x58>,
+			       <&dmac2 0x59>, <&dmac2 0x58>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 203>;
+			status = "disabled";
+		};
+
 		dmac1: dma-controller at e7300000 {
 			compatible = "renesas,dmac-r8a77980",
 				     "renesas,rcar-dmac";
#4 lore raw

PATCH v2 3/5 arm64: dts: renesas: r8a77980: add EtherAVB support

In reply to Sergei Shtylyov

Define the generic R8A77980 part of the EtherAVB device node.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- removed the 2nd address/size tuple from the "reg" property;
- changed the "phy-mode" property to the RGMII by default.

 arch/arm64/boot/dts/renesas/r8a77980.dtsi |   44 ++++++++++++++++++++++++++++++
 1 file changed, 44 insertions(+)
arch/arm64/boot/dts/renesas/r8a77980.dtsi +44 -0
Index: renesas/arch/arm64/boot/dts/renesas/r8a77980.dtsi
===================================================================
@@ -164,6 +164,50 @@
 			status = "disabled";
 		};
 
+		avb: ethernet at e6800000 {
+			compatible = "renesas,etheravb-r8a77980",
+				     "renesas,etheravb-rcar-gen3";
+			reg = <0 0xe6800000 0 0x800>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15",
+					  "ch16", "ch17", "ch18", "ch19",
+					  "ch20", "ch21", "ch22", "ch23",
+					  "ch24";
+			clocks = <&cpg CPG_MOD 812>;
+			power-domains = <&sysc 32>;
+			resets = <&cpg 812>;
+			phy-mode = "rgmii";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		scif0: serial at e6e60000 {
 			compatible = "renesas,scif-r8a77980",
 				     "renesas,rcar-gen3-scif",
#5 lore raw

PATCH v2 3/5 arm64: dts: renesas: r8a77980: add EtherAVB support

Quoted 6 lines · Sergei Shtylyov

Define the generic R8A77980 part of the EtherAVB device node.

Based on the original (and large) patch by Vladimir Barinov.

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#6 lore raw

PATCH v2 4/5 arm64: dts: renesas: initial Condor board device tree

In reply to Sergei Shtylyov

Add the initial device tree for the R8A77980 SoC based Condor board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- removed the useless "status" property from the SCIF_CLK node;
- fixed the memory size;
- added Geert's tag.

 arch/arm64/boot/dts/renesas/Makefile            |    1 
 arch/arm64/boot/dts/renesas/r8a77980-condor.dts |   45 ++++++++++++++++++++++++
 2 files changed, 46 insertions(+)
arch/arm64/boot/dts/renesas/Makefile +1 -0
Index: renesas/arch/arm64/boot/dts/renesas/Makefile
===================================================================
@@ -8,4 +8,5 @@ dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-sa
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-m3ulcb-kf.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb r8a77970-v3msk.dtb
+dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-condor.dtb
 dtb-$(CONFIG_ARCH_R8A77995) += r8a77995-draak.dtb
arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +45 -0

45 lines not on this page · raw message

#7 lore raw

PATCH v2 4/5 arm64: dts: renesas: initial Condor board device tree

Hi Sergei,

Quoted 36 lines · Sergei Shtylyov

Add the initial device tree for the R8A77980 SoC based Condor board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- removed the useless "status" property from the SCIF_CLK node;
- fixed the memory size;
- added Geert's tag.

arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +17 -0
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Condor board
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018 Cogent Embedded, Inc.
+ */
+
+/dts-v1/;
+#include "r8a77980.dtsi"
+
+/ {
+       model = "Renesas Condor board based on r8a77980";
+       compatible = "renesas,condor", "renesas,r8a77980";
+
+       aliases {
+               serial0 = &scif0;

arch/arm64/boot/dts/renesas/r8a77980-condor.dts line 27

Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +10 -0
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       memory at 48000000 {
+               device_type = "memory";
+               /* first 128MB is reserved for secure area. */
+               reg = <0 0x48000000 0 0xb8000000>;

Shouldn't the size be 0x78000000, or is there really 3 GiB of RAM?

oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#8 lore raw

PATCH v2 4/5 arm64: dts: renesas: initial Condor board device tree

Hello!

Quoted 40 lines · Geert Uytterhoeven
Quoted 40 lines

Add the initial device tree for the R8A77980 SoC based Condor board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- removed the useless "status" property from the SCIF_CLK node;
- fixed the memory size;
- added Geert's tag.

arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +21 -0
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Condor board
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018 Cogent Embedded, Inc.
+ */
+
+/dts-v1/;
+#include "r8a77980.dtsi"
+
+/ {
+       model = "Renesas Condor board based on r8a77980";
+       compatible = "renesas,condor", "renesas,r8a77980";
+
+       aliases {
+               serial0 = &scif0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
Quoted 8 lines

arch/arm64/boot/dts/renesas/r8a77980-condor.dts line 27

Quoted 6 lines
arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +6 -0
+       };
+
+       memory at 48000000 {
+               device_type = "memory";
+               /* first 128MB is reserved for secure area. */
+               reg = <0 0x48000000 0 0xb8000000>;

Shouldn't the size be 0x78000000, or is there really 3 GiB of RAM?

Ugh, so I finally mixed up limit and size... :-/

Quoted 3 lines

oetje,eeting}s,

Geert

MBR, Sergei

#9 lore raw

PATCH v2 4/5 arm64: dts: renesas: initial Condor board device tree

Quoted 53 lines · Sergei Shtylyov

Hello!

Quoted 40 lines · Geert Uytterhoeven
Quoted 40 lines

Add the initial device tree for the R8A77980 SoC based Condor board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- removed the useless "status" property from the SCIF_CLK node;
- fixed the memory size;
- added Geert's tag.

arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +21 -0
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Condor board
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018 Cogent Embedded, Inc.
+ */
+
+/dts-v1/;
+#include "r8a77980.dtsi"
+
+/ {
+       model = "Renesas Condor board based on r8a77980";
+       compatible = "renesas,condor", "renesas,r8a77980";
+
+       aliases {
+               serial0 = &scif0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
Quoted 8 lines

arch/arm64/boot/dts/renesas/r8a77980-condor.dts line 27

Quoted 6 lines
arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +6 -0
+       };
+
+       memory at 48000000 {
+               device_type = "memory";
+               /* first 128MB is reserved for secure area. */
+               reg = <0 0x48000000 0 0xb8000000>;

Shouldn't the size be 0x78000000, or is there really 3 GiB of RAM?

Quoted 1 line

Ugh, so I finally mixed up limit and size... :-/

Thanks, I will apply the following, with the memory corrected to 2 GiB.

From: Sergei Shtylyov <[email protected]>
Subject: [PATCH] arm64: dts: renesas: initial Condor board device tree

Add the initial device tree for the R8A77980 SoC based Condor board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

[simon: correct memory size to 0x78000000 (2GiB)]
---
 arch/arm64/boot/dts/renesas/Makefile            |  1 +
 arch/arm64/boot/dts/renesas/r8a77980-condor.dts | 45 +++++++++++++++++++++++++
 2 files changed, 46 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77980-condor.dts
arch/arm64/boot/dts/renesas/Makefile +1 -0
index 2186d0193b73..c885eef4e660 100644
@@ -8,4 +8,5 @@ dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-m3ulcb-kf.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb r8a77970-v3msk.dtb
+dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-condor.dtb
 dtb-$(CONFIG_ARCH_R8A77995) += r8a77995-draak.dtb
arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +45 -0

45 lines not on this page · raw message

Signature · 1 line
2.11.0
#10 lore raw

PATCH v2 4/5 arm64: dts: renesas: initial Condor board device tree

Quoted 49 lines · Simon Horman
Quoted 49 lines
Quoted 48 lines
Quoted 36 lines

Add the initial device tree for the R8A77980 SoC based Condor board. The board has 1 debug serial port (SCIF0); include support for it, so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- removed the useless "status" property from the SCIF_CLK node;
- fixed the memory size;
- added Geert's tag.

arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +17 -0
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Condor board
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018 Cogent Embedded, Inc.
+ */
+
+/dts-v1/;
+#include "r8a77980.dtsi"
+
+/ {
+       model = "Renesas Condor board based on r8a77980";
+       compatible = "renesas,condor", "renesas,r8a77980";
+
+       aliases {
+               serial0 = &scif0;

arch/arm64/boot/dts/renesas/r8a77980-condor.dts line 27

Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77980-condor.dts new file +10 -0
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       memory at 48000000 {
+               device_type = "memory";
+               /* first 128MB is reserved for secure area. */
+               reg = <0 0x48000000 0 0xb8000000>;

Shouldn't the size be 0x78000000, or is there really 3 GiB of RAM?

Quoted 3 lines
Quoted 1 line

Ugh, so I finally mixed up limit and size... :-/

Thanks, I will apply the following, with the memory corrected to 2 GiB.

Thank you! Just made sure that whatever is in this node in .dts, the RAM size
ends up being 0x78000000. Probably U-Boot is too smart. :-)

MBR, Sergei

#11 lore raw

PATCH v2 5/5 arm64: dts: renesas: condor: add EtherAVB support

In reply to Sergei Shtylyov

Define the Condor board dependent part of the EtherAVB device node.

Based on the original (and large) patch by Vladimir Barinov.

---
Changes in version 2:
- added the "renesas,no-ether-link" property;
- overrode the "phy-mode" property.

 arch/arm64/boot/dts/renesas/r8a77980-condor.dts |   13 +++++++++++++
 1 file changed, 13 insertions(+)
arch/arm64/boot/dts/renesas/r8a77980-condor.dts +13 -0
Index: renesas/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
===================================================================
@@ -15,6 +15,7 @@
 
 	aliases {
 		serial0 = &scif0;
+		ethernet0 = &avb;
 	};
 
 	chosen {
@@ -28,6 +29,18 @@
 	};
 };
 
+&avb {
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy0>;
+	renesas,no-ether-link;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+	};
+};
+
 &extal_clk {
 	clock-frequency = <16666666>;
 };
Applied
#12 lore raw

v2 cover Add R8A77980/Condor board support

In reply to Sergei Shtylyov
Quoted 11 lines · Sergei Shtylyov

Hello!

Here's the set of 11 patches against Simon Horman's 'renesas.git' repo's 'renesas-devel-20180216-v4.16-rc1' tag. I'm adding the device tree support for the R8A77980-based Condor board (note that NFS root would only work on the Condor boards [re]wired for booting from EtherAVB -- we haven't been able to get the 'sh_eth' driver working in either U-Boot or Linux so far). The necessary SYS-DMAC, [H]SCIF, and EtherAVB bindings updates have been posted, the clock driver has been reposted yesterday, and the merged patches have been dropped from this respin of the series...

Quoted 5 lines

[1/5] soc: renesas: rcar-sysc: add R8A77980 support [2/5] arm64: dts: renesas: r8a77980: add [H]SCIF support [3/5] arm64: dts: renesas: r8a77980: add EtherAVB support [4/5] arm64: dts: renesas: initial Condor board device tree [5/5] arm64: dts: renesas: condor: add EtherAVB support

Thanks, applied.