Skip to contentSkip to conversation

ubiattach fails after ubiformat

DISCUSSION Steve Kinneberg 1 participant 2 messages Dec 6, 2021 – Dec 13, 2021 Memory technology devices (MTD)

lore
Share & tools
lore
#0 lore raw

Hello,

I am having problems using ubiattach with an SLC NAND Flash device on a custom board based off the NXP LS1046ARDB reference design running OpenWrt 21.02. If I issue the following commands, ubiattach appears to work:

flash_erase /dev/mtd0 0 4096
ubiattach -m 0 -O 2048

If I use ubiformat, then ubiattach will fail. Here is the sequence of commands that I have tried:

flash_erase /dev/mtd0 0 4096
ubiformat /dev/mtd0 -s 2048 -O 2048
ubiattach -m 0 -O 2048

At this point, the kernel repeatedly outputs the following (the PEB value increments):

[13440.396590] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 3:0, read only 64 bytes, retry
[13440.408305] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 3:0, read only 64 bytes, retry
[13440.420021] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 3:0, read only 64 bytes, retry
[13440.431737] ubi0 error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 3:0, read 64 bytes
[13440.441660] CPU: 2 PID: 3110 Comm: ubiattach Not tainted 5.4.154 #0
[13440.447924] Hardware name: XAPH Board (DT)
[13440.452013] Call trace:
[13440.454453]  dump_backtrace+0x0/0x120
[13440.458110]  show_stack+0x14/0x20
[13440.461417]  dump_stack+0xb4/0xf4
[13440.464724]  ubi_io_read+0x17c/0x308
[13440.468292]  ubi_io_read_ec_hdr+0x4c/0x210
[13440.472383]  ubi_attach+0x40c/0x1330
[13440.475953]  ubi_attach_mtd_dev+0x570/0xb08
[13440.480130]  ctrl_cdev_ioctl+0x3ac/0x510
[13440.484047]  do_vfs_ioctl+0xa4/0xe00
[13440.487617]  ksys_ioctl+0x44/0x90
[13440.490924]  __arm64_sys_ioctl+0x1c/0x210
[13440.494928]  el0_svc_handler+0x88/0x118
[13440.498757]  el0_svc+0x8/0x210

The same sequence of commands using the nandsim driver on a desktop Linux system works fine. I can even flash a UBI image or create volumes using the nandsim.

Here is Linux kernel bootup messages regarding identification of the NAND Flash:

[    0.787530] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xac
[    0.793889] nand: AMD/Spansion S34MS04G2
[    0.797810] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[    0.806065] Bad block table found at page 262080, version 0x01
[    0.813052] Bad block table found at page 262016, version 0x01
[    0.819495] mtd: no mtd-id
[    0.822506] fsl,ifc-nand 7e800000.nand: IFC NAND device at 0x7e800000, bank 0

The part number and size are correct for the HW.
Linux kernel version (from /proc/version):

Linux version 5.4.154 (steve@steve-linux) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16330+8-4607f55439)) #0 SMP PREEMPT Tue Nov 30 14:37:50 2021

Output from /proc/mtd:

dev: size erasesize name
mtd0: 20000000 00020000 "7e800000.flash"
mtd1: 00100000 00001000 "bl2"
mtd2: 00400000 00001000 "fip"
mtd3: 00100000 00001000 "u-boot-env"
mtd4: 00300000 00001000 "reserved-1"
mtd5: 00040000 00001000 "fman"
mtd6: 005c0000 00001000 "reserved-2"
mtd7: 00100000 00001000 "dtb"
mtd8: 01000000 00001000 "kernel"
mtd9: 02000000 00001000 "rootfs"
mtd10: 0186e000 00001000 "rootfs_data"
mtd11: 03100000 00001000 "firmware"

Linux boot command line:

root=/dev/mtdblock9 rootfstype=squashfs noinitrd earlycon=uart8250,mmio,0x21c0500 console=ttyS0,115200 mtdparts=1550000.spi:1m(bl2),4m(fip),1m(u-boot-env),3m(reserved-1),256k(fman),5888k(reserved-2),1m(dtb),16m(kernel),32m(rootfs),49m@0xf00000(firmware),64m@0x000000(nor-flash);7e800000.flash

I presume that I am missing a step or mis-configured something. Any pointers would be greatly appreciated.

Thanks,
Steve Kinneberg

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

#1 lore raw
Quoted 96 lines · Steve Kinneberg

Hello,

I am having problems using ubiattach with an SLC NAND Flash device on a custom board based off the NXP LS1046ARDB reference design running OpenWrt 21.02.  If I issue the following commands, ubiattach appears to work:

flash_erase /dev/mtd0 0 4096
ubiattach -m 0 -O 2048

If I use ubiformat, then ubiattach will fail.  Here is the sequence of commands that I have tried:

flash_erase /dev/mtd0 0 4096
ubiformat /dev/mtd0 -s 2048 -O 2048
ubiattach -m 0 -O 2048

At this point, the kernel repeatedly outputs the following (the PEB value increments):

[13440.396590] ubi0 warning: ubi_io_read: error -74 (ECC error) while
reading 64 bytes from PEB 3:0, read only 64 bytes, retry
[13440.408305] ubi0 warning: ubi_io_read: error -74 (ECC error) while
reading 64 bytes from PEB 3:0, read only 64 bytes, retry
[13440.420021] ubi0 warning: ubi_io_read: error -74 (ECC error) while
reading 64 bytes from PEB 3:0, read only 64 bytes, retry
[13440.431737] ubi0 error: ubi_io_read: error -74 (ECC error) while
reading 64 bytes from PEB 3:0, read 64 bytes
[13440.441660] CPU: 2 PID: 3110 Comm: ubiattach Not tainted 5.4.154 #0
[13440.447924] Hardware name: XAPH Board (DT)
[13440.452013] Call trace:
[13440.454453]  dump_backtrace+0x0/0x120
[13440.458110]  show_stack+0x14/0x20
[13440.461417]  dump_stack+0xb4/0xf4
[13440.464724]  ubi_io_read+0x17c/0x308
[13440.468292]  ubi_io_read_ec_hdr+0x4c/0x210
[13440.472383]  ubi_attach+0x40c/0x1330
[13440.475953]  ubi_attach_mtd_dev+0x570/0xb08
[13440.480130]  ctrl_cdev_ioctl+0x3ac/0x510
[13440.484047]  do_vfs_ioctl+0xa4/0xe00
[13440.487617]  ksys_ioctl+0x44/0x90
[13440.490924]  __arm64_sys_ioctl+0x1c/0x210
[13440.494928]  el0_svc_handler+0x88/0x118
[13440.498757]  el0_svc+0x8/0x210

The same sequence of commands using the nandsim driver on a desktop Linux system works fine.  I can even flash a UBI image or create volumes using the nandsim.

Here is Linux kernel bootup messages regarding identification of the NAND Flash:

[    0.787530] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xac [    0.793889] nand: AMD/Spansion S34MS04G2
[    0.797810] nand: 512 MiB, SLC, erase size: 128 KiB, page size:
2048, OOB size: 128
[    0.806065] Bad block table found at page 262080, version 0x01 [    0.813052] Bad block table found at page 262016, version 0x01 [    0.819495] mtd: no mtd-id
[    0.822506] fsl,ifc-nand 7e800000.nand: IFC NAND device at 0x7e800000, bank 0

The part number and size are correct for the HW.
Linux kernel version (from /proc/version):

Linux version 5.4.154 (steve@steve-linux) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16330+8-4607f55439)) #0 SMP PREEMPT Tue Nov 30 14:37:50 2021

Output from /proc/mtd:

dev:    size   erasesize  name
mtd0: 20000000 00020000 "7e800000.flash"
mtd1: 00100000 00001000 "bl2"
mtd2: 00400000 00001000 "fip"
mtd3: 00100000 00001000 "u-boot-env"
mtd4: 00300000 00001000 "reserved-1"
mtd5: 00040000 00001000 "fman"
mtd6: 005c0000 00001000 "reserved-2"
mtd7: 00100000 00001000 "dtb"
mtd8: 01000000 00001000 "kernel"
mtd9: 02000000 00001000 "rootfs"
mtd10: 0186e000 00001000 "rootfs_data"
mtd11: 03100000 00001000 "firmware"

Linux boot command line:

root=/dev/mtdblock9 rootfstype=squashfs noinitrd earlycon=uart8250,mmio,0x21c0500 console=ttyS0,115200 mtdparts=1550000.spi:1m(bl2),4m(fip),1m(u-boot-env),3m(reserved- 1),256k(fman),5888k(reserved- 2),1m(dtb),16m(kernel),32m(rootfs),49m@0xf00000(firmware), 64m@0x000000(nor-flash);7e800000.flash

Quoted 5 lines

I presume that I am missing a step or mis-configured something.  Any pointers would be greatly appreciated.

Thanks,
Steve Kinneberg

Hi,

I'm still having problems with ubiattach. I've even tried hacking the Linux kernel driver as suggested in this thread from almost 3 years
ago: https://www.spinics.net/lists/linux-mtd/msg05327.html

That thread is the closest I can find to a similar problem to what I'm having, but the suggested solutions in it do not work for me.

I've since discovered that even though ubiattach works after flash_erase, if I detach and re-attach, I get the same kernel errors.

Any suggestions on debugging this will be greatly appreciated.

Thanks,
Steve

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/