atmel_serial: Split the interrupt handler
Subsystems (2)
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi,
Quoted 5 lines
Quoted 5 lines
From: Remy Bohmer <[email protected]>
This patch splits up the interrupt handler of the serial port into a interrupt top-half and a tasklet.
Quoted 13 lines
Review
Quoted 13 lines
The goal is to get the interrupt top-half as short as possible to minimize latencies on interrupts. But the old code also does some calls in the interrupt handler that are not allowed on preempt-RT in
IRQF_NODELAYcontext. This handler is executed in this context because of the interrupt sharing with the timer interrupt.(quoted diff) +7
-0+static void +atmel_buffer_rx_char(struct uart_port *port, unsigned int status, + unsigned int ch) +{ + struct atmel_uart_port *atmel_port = (struct atmel_uart_port *)port; + struct circ_buf *ring = &atmel_port->rx_ring; + struct atmel_uart_char *c;
I'm testing this patch on an at91sam9260 on 2.6.24-rt. I'm using this patch with the tclib support for hrtimer and the clocksource pit_clk. These are the results:
- Voluntary Kernel Preemption the system (crash)
- Preemptible Kernel (crash)
/*
* Drop the lock here since it might end up calling
* uart_start(), which takes the lock. spin_unlock(&port->lock);
*/
tty_flip_buffer_push(port->info->tty);
/*
spin_lock(&port->lock);
*/
The same code with this comments out runs
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
The system is stable and doesn't crash reverting this patch. I don't test with the thread hardirqs active.
Quoted 16 lines
Quoted 16 lines
(quoted diff) +15
-0+ + if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE)) + /* Buffer overflow, ignore char */ + return; + + c = &((struct atmel_uart_char *)ring->buf)[ring->head]; + c->status = status; + c->ch = ch; + + /* Make sure the character is stored before we update head. */ + smp_wmb(); + + ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1); +} +
...
Quoted 4 lines
Quoted 4 lines
(quoted diff) +1
-0+ port = &atmel_ports[pdev->id]; atmel_init_port(port, pdev);
Quoted 8 lines
Review
Quoted 8 lines
(quoted diff) +6
-0+ ret = -ENOMEM; + data = kmalloc(ATMEL_SERIAL_RINGSIZE, GFP_KERNEL); + if (!data) + goto err_alloc_ring; + port->rx_ring.buf = data; + ret = uart_add_one_port(&atmel_uart, &port->uart);
Is the kmalloc correct?
maybe:
data = kmalloc(ATMEL_SERIAL_RINGSIZE * sizeof(struct atmel_uart_char), GFP_KERNEL);
Quoted 14 lines
Quoted 14 lines
(quoted diff) +3
-0if (ret) goto err_add_port;@@ -1013,6 +1142,9 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev) return 0; err_add_port: + kfree(port->rx_ring.buf); + port->rx_ring.buf = NULL; +err_alloc_ring: if (!atmel_is_console_port(&port->uart)) { clk_disable(port->clk); clk_put(port->clk);@@ -1033,6 +1165,9 @@ static int __devexit atmel_serial_remove(struct platform_device *pdev)
Quoted 6 lines
Review static int __devexit atmel_serial_remove(struct platform_device *pdev) · line 1171
Quoted 6 lines
(quoted diff) +3
-0ret = uart_remove_one_port(&atmel_uart, port); + tasklet_kill(&atmel_port->tasklet); + kfree(atmel_port->rx_ring.buf); +
Why the tasklet_kill is not done in atmel_shutdown?
Regards
Michael
Quoted 6 lines · On Wed, 30 Jan 2008 00:12:23 +0100 michael <[email protected]> wrote:
I'm testing this patch on an at91sam9260 on 2.6.24-rt. I'm using this patch with the tclib support for hrtimer and the clocksource
pit_clk. These are the results:- Voluntary Kernel Preemption the system (crash)
- Preemptible Kernel (crash)
Ouch. I'm assuming this is with DMA disabled?
Quoted 10 lines
/*
* Drop the lock here since it might end up calling
*uart_start(), which takes the lock.spin_unlock(&port->lock);
*/tty_flip_buffer_push(port->info->tty); /* spin_lock(&port->lock);*/
The same code with this comments out runs
Now, _that_ is strange. I can't see anything that needs protection across that call; in fact, I think we can lock a lot less than what we currently do.
Quoted 2 lines
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
Is it worse than before? IIRC Remy mentioned something about IRQF_NODELAY being the reason for moving all this code to softirq context in the first place; does the interrupt handler run in hardirq context?
Quoted 2 lines
The system is stable and doesn't crash reverting this patch. I don't test with the thread hardirqs active.
Ok.
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
(quoted diff) +4
-0+ ret = -ENOMEM; + data = kmalloc(ATMEL_SERIAL_RINGSIZE, GFP_KERNEL); + if (!data) + goto err_alloc_ring;
Quoted 8 lines
Quoted 4 lines
Review
Quoted 4 lines
(quoted diff) +2
-0+ port->rx_ring.buf = data; + ret = uart_add_one_port(&atmel_uart, &port->uart);Is the kmalloc correct?
maybe:
data =kmalloc(ATMEL_SERIAL_RINGSIZE * sizeof(struct atmel_uart_char), GFP_KERNEL);
I think you're right. Can you change it and see if it helps?
I guess I didn't test it thoroughly enough with DMA disabled...slub_debug ought to catch such things, but not until we receive enough data to actually overflow the buffer.
Quoted 9 lines
Quoted 8 lines
Review static int __devexit atmel_serial_remove(struct platform_device *pdev) · line 1171
Quoted 8 lines
(quoted diff) +3
-0@@ -1033,6 +1165,9 @@ static int __devexit atmel_serial_remove(struct platform_device *pdev) ret = uart_remove_one_port(&atmel_uart, port); + tasklet_kill(&atmel_port->tasklet); + kfree(atmel_port->rx_ring.buf); +Why the
tasklet_killis not done inatmel_shutdown?
Why should it be? If it should, we must move the call to tasklet_init into atmel_startup too, and I don't really see the point.
Haavard
Hello Haavard (and Michael),
First I want to mention that I did not found the time yet to test your latest integration of these atmel_serial patches, and I only know that your set of the end of December works fine. I do not know the changes you made since posting that set and your latest patch-set.
But let me clear some things up:
The original patchset I posted, existed of a set of patches suitable for the mainline kernel, plus an additional patch for Preempt-RT only. So, the splitup of the interrupt handler was also needed for Preempt-RT, but it was not the only patch that was needed on preempt-rt.
Now looking at this problem:
Quoted 9 lines
Quoted 9 lines
* Drop the lock here since it might end up calling
*uart_start(), which takes the lock.spin_unlock(&port->lock);
*/tty_flip_buffer_push(port->info->tty); /* spin_lock(&port->lock);*/
The same code with this comments out runs
I expect the UART generating the problem is the DBGU port. The DBGU shares its interrupt line with the timer interrupt with the IRQF_TIMER flag set, and thus the DBGU interrupt handler is running in IRQF_NODELAY context. Within this context it is forbidden to lock a normal spinlock, because a normal spinlock is converted to a mutex on Preempt-RT; a mutex can sleep which is forbidden in interrupt context. So, to get around this problem, this lock spinlock has to be of the raw_spinlock_t type. The raw_spinlock_t is the normal mainline-kernel spinlock, and as such it is not converted to a mutex, and will therefor never sleep.
Attached a patch that changes this spinlock type. I used it in my patchset, but your updates of December last year do not need this patch anymore, so apparantly you changed something that has a regression on Preempt-RT...
Quoted 2 lines
Quoted 2 lines
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
This problem is not there in the December-set either. It works like a charm...
I believe I have to look at the latest set of patches, and try to find any regressions. Do you have a location somewhere where I can download the latest versions? Or do I need to dig through LKML to find the latest... ;-)
Kind Regards,
Remy
2008/1/30, Haavard Skinnemoen <[email protected]>:
Quoted 69 lines
Quoted 6 lines · On Wed, 30 Jan 2008 00:12:23 +0100 michael <[email protected]> wrote:
I'm testing this patch on an at91sam9260 on 2.6.24-rt. I'm using this patch with the tclib support for hrtimer and the clocksource
pit_clk. These are the results:- Voluntary Kernel Preemption the system (crash)
- Preemptible Kernel (crash)Ouch. I'm assuming this is with DMA disabled?
Quoted 10 lines
/*
* Drop the lock here since it might end up calling
*uart_start(), which takes the lock.spin_unlock(&port->lock);
*/tty_flip_buffer_push(port->info->tty); /* spin_lock(&port->lock);*/
The same code with this comments out runsNow, _that_ is strange. I can't see anything that needs protection across that call; in fact, I think we can lock a lot less than what we currently do.
Quoted 2 lines
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
Is it worse than before? IIRC Remy mentioned something about
IRQF_NODELAYbeing the reason for moving all this code to softirq context in the first place; does the interrupt handler run in hardirq context?Quoted 2 lines
The system is stable and doesn't crash reverting this patch. I don't test with the thread hardirqs active.
Ok.
Quoted 8 lines
Quoted 8 lines
Review
Quoted 8 lines
(quoted diff) +6
-0+ ret = -ENOMEM; + data = kmalloc(ATMEL_SERIAL_RINGSIZE, GFP_KERNEL); + if (!data) + goto err_alloc_ring; + port->rx_ring.buf = data; + ret = uart_add_one_port(&atmel_uart, &port->uart);Quoted 4 lines
Is the kmalloc correct?
maybe:
data =kmalloc(ATMEL_SERIAL_RINGSIZE * sizeof(struct atmel_uart_char), GFP_KERNEL);I think you're right. Can you change it and see if it helps?
I guess I didn't test it thoroughly enough with DMA disabled...slub_debug ought to catch such things, but not until we receive enough data to actually overflow the buffer.
Quoted 9 lines
Quoted 8 lines
Review static int __devexit atmel_serial_remove(struct platform_device *pdev) · line 1171
Quoted 8 lines
(quoted diff) +3
-0@@ -1033,6 +1165,9 @@ static int __devexit atmel_serial_remove(struct platform_device *pdev) ret = uart_remove_one_port(&atmel_uart, port); + tasklet_kill(&atmel_port->tasklet); + kfree(atmel_port->rx_ring.buf); +Why the
tasklet_killis not done inatmel_shutdown?
Quoted 5 lines
Why should it be? If it should, we must move the call to
tasklet_initintoatmel_startuptoo, and I don't really see the point.Haavard
On PREEMPT-RT we may not block on a normal spinlock in IRQ/IRQF_NODELAY-context. This patch fixes this by making the lock a raw_spinlock_t for the Atmel serial console.
This patch demands the following patches to be installed first:
* atmel_serial_cleanup.patch
* atmel_serial_irq_splitup.patch
--- include/linux/serial_core.h | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
include/linux/serial_core.h +6 -1
@@ -226,7 +226,12 @@ struct uart_icount { typedef unsigned int __bitwise__ upf_t;struct uart_port { -spinlock_t lock;/* port lock */ + +#ifdef CONFIG_SERIAL_ATMEL +raw_spinlock_t lock;/* port lock */ +#else +spinlock_t lock;/* port lock */ +#endif unsigned int iobase;/* in/out[bwl] */ unsigned char __iomem *membase;/* read/write[bwl] */ unsigned int irq;/* irq number */
Quoted 21 lines · On Wed, 30 Jan 2008 11:21:49 +0100 "Remy Bohmer" <[email protected]> wrote:
Quoted 9 lines
Quoted 9 lines
* Drop the lock here since it might end up calling
*uart_start(), which takes the lock.spin_unlock(&port->lock);
*/tty_flip_buffer_push(port->info->tty); /* spin_lock(&port->lock);*/
The same code with this comments out runsI expect the UART generating the problem is the DBGU port. The DBGU shares its interrupt line with the timer interrupt with the
IRQF_TIMERflag set, and thus the DBGU interrupt handler is running inIRQF_NODELAYcontext. Within this context it is forbidden to lock a normal spinlock, because a normal spinlock is converted to a mutex on Preempt-RT; a mutex can sleep which is forbidden in interrupt context. So, to get around this problem, this lock spinlock has to be of theraw_spinlock_ttype. Theraw_spinlock_tis the normal mainline-kernel spinlock, and as such it is not converted to a mutex, and will therefor never sleep.
Quoted 4 lines
Attached a patch that changes this spinlock type. I used it in my patchset, but your updates of December last year do not need this patch anymore, so apparantly you changed something that has a regression on Preempt-RT...
The code above is from the tasklet, so I don't think that's the problem. The interrupt handler doesn't take any locks.
Or are spinlocks not allowed in softirq context either?
Quoted 4 lines
I believe I have to look at the latest set of patches, and try to find any regressions. Do you have a location somewhere where I can download the latest versions? Or do I need to dig through LKML to find the latest... ;-)
They are in -mm. You were Cc'ed I think...
Haavard
Haavard
Hello Haavard,
Quoted 3 lines
The code above is from the tasklet, so I don't think that's the problem. The interrupt handler doesn't take any locks.
Or are spinlocks not allowed in softirq context either?
They are allowed there...
So, it has to be something different.
Quoted 5 lines
Quoted 4 lines
I believe I have to look at the latest set of patches, and try to find any regressions. Do you have a location somewhere where I can download the latest versions? Or do I need to dig through LKML to find the latest... ;-)
They are in -mm. You were Cc'ed I think...
Yes, I saw them, but I did not know if there were any updates in the mean time, because I had seen some discussions, which confused me a bit about the current status of the complete set.
Quoted 2 lines
- with full preemption it runs but the serial line can't be used for receiving at high bit rate (using lrz)
A few questions arise here to me:
* What serial port is used here? (DBGU, or something else)
* No DMA was used, was flow-control enabled? (cannot with DBGU)
* If some other UART, why not using DMA?
Notice that the DBGU has no flow control, and just a 1 byte FIFO (thus no fifo at all).
At high speeds (e.g. >=115200) it is _likely_ that you will miss characters, nothing can prevent that. DBGU should only be used at lower speeds, or just as text console. 115200 is running fine here as text-console.
I would not expect that the behaviour is worse than without the patchset, because without it it does not work at all on Preempt-RT, but also: there was done much more in interrupt context previously, so the chance of buffer overruns was much more likely in the old situation.
The real interrupt handler (doing the reading from the fifo) must be as short as possible, to be able to keep up with the data flow.
A simple calculation: 115200bps results in approx. 11520 bytes per second. This means that the interrupt handler must be capable of handling each byte on DBGU within 87us. With a worst case interrupt latency of about 85us, and average between 2us and 54us (on Preempt-RT and AT91RM9200), you can simply understand that this will not match, how good/fast the interrupt handling will ever be.
So, I suggest to either use flow-control, or DMA for bulkdata... (thus not DBGU)
Kind Regards,
Remy
Quoted 9 lines · On Wed, 30 Jan 2008 12:05:40 +0100 "Remy Bohmer" <[email protected]> wrote:
Quoted 5 lines
Quoted 4 lines
I believe I have to look at the latest set of patches, and try to find any regressions. Do you have a location somewhere where I can download the latest versions? Or do I need to dig through LKML to find the latest... ;-)
They are in -mm. You were Cc'ed I think...
Yes, I saw them, but I did not know if there were any updates in the mean time, because I had seen some discussions, which confused me a bit about the current status of the complete set.
There's been one update, atmel_serial-add-dma-support-fix.patch, which you were also Cc'ed on.
Haavard
Hi,
Quoted 6 lines
A few questions arise here to me:
* What serial port is used here? (DBGU, or something else)
* No DMA was used, was flow-control enabled? (cannot with DBGU)
* If some other UART, why not using DMA?
DBGU, so no flow control
Quoted 7 lines
Notice that the DBGU has no flow control, and just a 1 byte FIFO (thus no fifo at all).
At high speeds (e.g. >=115200) it is _likely_ that you will miss characters, nothing can prevent that. DBGU should only be used at lower speeds, or just as text console. 115200 is running fine here as text-console.
Overrun are admitted using DBGU and UART1..n without flow control, but with the old version of the driver I can send a file using lrz and with the new and full preemption is impossible.
Quoted 22 lines
I would not expect that the behaviour is worse than without the patchset, because without it it does not work at all on Preempt-RT, but also: there was done much more in interrupt context previously, so the chance of buffer overruns was much more likely in the old situation.
The real interrupt handler (doing the reading from the fifo) must be as short as possible, to be able to keep up with the data flow.A simple calculation: 115200bps results in approx. 11520 bytes per second. This means that the interrupt handler must be capable of handling each byte on DBGU within 87us. With a worst case interrupt latency of about 85us, and average between 2us and 54us (on Preempt-RT and AT91RM9200), you can simply understand that this will not match, how good/fast the interrupt handling will ever be.
So, I suggest to either use flow-control, or DMA for bulkdata... (thus not DBGU)
Kind Regards,
Remy
Hi
Quoted 11 lines
Quoted 3 lines · On Wed, 30 Jan 2008 00:12:23 +0100 michael <[email protected]> wrote:
- Voluntary Kernel Preemption the system (crash)
- Preemptible Kernel (crash)Ouch. I'm assuming this is with DMA disabled?
Yes, is with DMA disabled
Quoted 12 lines
Quoted 11 lines
/*
* Drop the lock here since it might end up calling
*uart_start(), which takes the lock.spin_unlock(&port->lock);
*/tty_flip_buffer_push(port->info->tty); /* spin_lock(&port->lock);*/
The same code with this comments out runs
Quoted 5 lines
Now, _that_ is strange. I can't see anything that needs protection across that call; in fact, I think we can lock a lot less than what we currently do.
I explain it bad:
- with spin_lock the system seems, there is no problem with Valuntary Preeption and Preemptible Kernel
- with full preemption it runs but the serial line can't be used for receiving at high bit rate (using lrz)
Quoted 10 lines
Quoted 3 lines
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
Is it worse than before? IIRC Remy mentioned something about
IRQF_NODELAYbeing the reason for moving all this code to softirq context in the first place; does the interrupt handler run in hardirq context?
In the complete preemption yes.
Quoted 7 lines
Quoted 3 lines
The system is stable and doesn't crash reverting this patch. I don't test with the thread hardirqs active.
Ok.
Quoted 8 lines
Quoted 4 lines
Is the kmalloc correct?
maybe:
data =kmalloc(ATMEL_SERIAL_RINGSIZE * sizeof(struct atmel_uart_char), GFP_KERNEL);I think you're right. Can you change it and see if it helps?
I just change it because I have corruption on receiving buffer. All my test are done with this fix
Quoted 5 lines
I guess I didn't test it thoroughly enough with DMA disabled...slub_debug ought to catch such things, but not until we receive enough data to actually overflow the buffer.
I just test it I don't have
buffer overflow.
I protect with a spinlock the access to the register when we sending from the tasklet. It is correct?
Quoted 5 lines
Why should it be? If it should, we must move the call to
tasklet_initintoatmel_startuptoo, and I don't really see the point.
Ok
Regards Michael
Quoted 5 lines · On Wed, 30 Jan 2008 11:29:59 +0100 michael <[email protected]> wrote:
Quoted 5 lines
Now, _that_ is strange. I can't see anything that needs protection across that call; in fact, I think we can lock a lot less than what we currently do.
Quoted 7 lines
I explain it bad:
- withspin_lockthe system seems, there is no problem with Valuntary Preeption and
Preemptible Kernel
- with full preemption it runs but the serial line can't be used for receiving at
high bit rate (using lrz)
...but if you drop the spinlock across the call to tty_flip_buffer_push, you get an Oops?
Could you post the Oops?
Quoted 11 lines
Quoted 10 lines
Quoted 3 lines
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
Is it worse than before? IIRC Remy mentioned something about
IRQF_NODELAYbeing the reason for moving all this code to softirq context in the first place; does the interrupt handler run in hardirq context?In the complete preemption yes.
Which question did you answer "yes" to? That it's worse than before or that the interrupt handler runs in hardirq context (i.e. IRQF_NODELAY)?
Quoted 5 lines
Quoted 3 lines
I think you're right. Can you change it and see if it helps?
I just change it because I have corruption on receiving buffer. All my test are done with this fix
Ok.
Quoted 7 lines
Quoted 5 lines
I guess I didn't test it thoroughly enough with DMA disabled...slub_debug ought to catch such things, but not until we receive enough data to actually overflow the buffer.
I just test it I don't have
buffer overflow.
No, I'd expect your allocation fix to take care of that. Or did you by any chance test without the fix and with slub_debug enabled?
Quoted 2 lines
I protect with a spinlock the access to the register when we sending from the tasklet. It is correct?
I have no idea. Could you post some more specifics about what you modified, for example a diff?
Most of the tasklet is already protected by the spinlock, so you must be careful to avoid any lock recursion.
Haavard
Hi,
Quoted 18 lines
Quoted 6 lines · On Wed, 30 Jan 2008 11:29:59 +0100 michael <[email protected]> wrote:
Quoted 6 lines
Now, _that_ is strange. I can't see anything that needs protection across that call; in fact, I think we can lock a lot less than what we currently do.
Quoted 8 lines
I explain it bad:
- withspin_lockthe system seems, there is no problem with Valuntary Preeption and
Preemptible Kernel
- with full preemption it runs but the serial line can't be used for receiving at
high bit rate (using lrz)
Quoted 6 lines
...but if you drop the spinlock across the call to
tty_flip_buffer_push, you get an Oops?Could you post the Oops?
So this code
/*
* Drop the lock here since it might end up calling
* uart_start(), which takes the lock.
*/spin_unlock(&port->lock);
tty_flip_buffer_push(port->info->tty);
spin_lock(&port->lock);
Works with:CONFIG_PREEMPT_RT=yCONFIG_PREEMPT=yCONFIG_PREEMPT_SOFTIRQS=yCONFIG_PREEMPT_HARDIRQS=yCONFIG_PREEMPT_BKL=y
but crash with:
# CONFIG_PREEMPT_NONE is not setCONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT_DESKTOP is not set
# CONFIG_PREEMPT_RT is not setCONFIG_PREEMPT_SOFTIRQS=y
# CONFIG_PREEMPT_HARDIRQS is not set
# CONFIG_PREEMPT_BKL is not setCONFIG_CLASSIC_RCU=y
Seems to work in the last config if I comment the spin_lock & spin_unlock call. /*
* Drop the lock here since it might end up calling
* uart_start(), which takes the lock.
spin_unlock(&port->lock); */
tty_flip_buffer_push(port->info->tty);
/* spin_lock(&port->lock); */
It is not readable because I can't compile it with debugging information (poor memory system)
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 4 lines
Complete Preemption (Real-Time) ok but the serials is just unusable due to too many overruns (just using lrz)
Is it worse than before? IIRC Remy mentioned something about
IRQF_NODELAYbeing the reason for moving all this code to softirq context in the first place; does the interrupt handler run in hardirq context?
Quoted 7 lines
Quoted 2 lines
In the complete preemption yes.
Which question did you answer "yes" to? That it's worse than before or that the interrupt handler runs in hardirq context (i.e.
IRQF_NODELAY)?
The interrupt handler run in IRQF_NODELAY context.
Quoted 17 lines
Quoted 7 lines
Quoted 4 lines
I think you're right. Can you change it and see if it helps?
I just change it because I have corruption on receiving buffer. All my test are done with this fix
Ok.
Quoted 6 lines
Quoted 6 lines
I guess I didn't test it thoroughly enough with DMA disabled...slub_debug ought to catch such things, but not until we receive enough data to actually overflow the buffer.
Quoted 8 lines
Quoted 3 lines
I just test it I don't have
buffer overflow.No, I'd expect your allocation fix to take care of that. Or did you by any chance test without the fix and with
slub_debugenabled?
I just meant that the buffer never fills up to its size.
Quoted 8 lines
Quoted 3 lines
I protect with a spinlock the access to the register when we sending from the tasklet. It is correct?
I have no idea. Could you post some more specifics about what you modified, for example a diff?
...
/* The interrupt handler does not take the lock */ spin_lock_irqsave(&port->lock, flags); atmel_tx_chars(port); spin_unlock_irqrestore(&port->lock, flags);
spin_lock(&port->lock);
...
The atmel_tx_chars using the serial device registers like the interrupt routine and so I think that it is possible to have interference during send operation.
Quoted 6 lines
Most of the tasklet is already protected by the spinlock, so you must be careful to avoid any lock recursion.
Haavard
Regards Michael
Quoted 10 lines · On Wed, 30 Jan 2008 16:26:27 +0100 michael <[email protected]> wrote:
Quoted 4 lines
I have no idea. Could you post some more specifics about what you modified, for example a diff?
...
/* The interrupt handler does not take the lock */spin_lock_irqsave(&port->lock, flags);atmel_tx_chars(port);spin_unlock_irqrestore(&port->lock, flags);
Sorry, this isn't going to work.
Please post a diff with the changes you did to the driver, and whatever output you got when it crashed.
It's really difficult to help you when I don't know (a) what code you're actually running, or (b) anything about the crash.
Quoted 4 lines
The
atmel_tx_charsusing the serial device registers like the interrupt routine
and so I think that it is possible to have interference during send operation.
No, it's only called from the tasklet, and the interrupt handler doesn't touch the TX data register. There shouldn't be any need to disable interrupts around the call to atmel_tx_chars(). In fact, this may very well be the cause of the overruns you're seeing.
Haavard
Hi,
Quoted 16 lines · Haavard Skinnemoen
Quoted 11 lines · On Wed, 30 Jan 2008 16:26:27 +0100 michael <[email protected]> wrote:
Quoted 5 lines
I have no idea. Could you post some more specifics about what you modified, for example a diff?
...
/* The interrupt handler does not take the lock */spin_lock_irqsave(&port->lock, flags);atmel_tx_chars(port);spin_unlock_irqrestore(&port->lock, flags);
Quoted 9 lines
Sorry, this isn't going to work.
Please post a diff with the changes you did to the driver, and whatever output you got when it crashed.
It's really difficult to help you when I don't know (a) what code you're actually running, or (b) anything about the crash.
Ok, but the problem is that I have some added code for using the uart with smart card in iso mode, (is never called) and the patch is not so clean. Now I return to the original patch without the spin_lock_irqsave and with the fix of buffer allocation,and I don't see the crash anymore. In full preemptive all works with threading hardirqs and sofirqs. I will do other testing before posting again.
Quoted 4 lines
Quoted 3 lines
The
atmel_tx_charsusing the serial device registers like the interrupt routine and so I think that it is possible to have interference during send operation.
Quoted 8 lines
No, it's only called from the tasklet, and the interrupt handler doesn't touch the TX data register. There shouldn't be any need to disable interrupts around the call to
atmel_tx_chars(). In fact, this may very well be the cause of the overruns you're seeing.Haavard
The overrun still remain. An lrz receive session is impossible using full preemption. I will try the dma patch too and test in iso mode for smart card.
Thanks
Quoted 3 lines · On Thu, 31 Jan 2008 02:53:50 +0100 michael <[email protected]> wrote:
The overrun still remain. An lrz receive session is impossible using full preemption. I will try the dma patch too and test in iso mode for smart card.
Hmm. Seems to work reasonably well on a non-rt kernel -- I get quite a few overruns, but nothing more than the Zmodem protocol can handle.
It seems to be very sensitive to network traffic though...could it have something to do with softirq scheduling? Could you try the patch below and see if you can trigger the error message?
Haavard
drivers/serial/atmel_serial.c +4 -1
@@ -337,9 +337,12 @@ atmel_buffer_rx_char(struct uart_port *port, unsigned int status,struct circ_buf *ring = &atmel_port->rx_ring;struct atmel_uart_char *c; -if (!CIRC_SPACE (ring->head, ring->tail,ATMEL_SERIAL_RINGSIZE )) +if (!CIRC_SPACE (ring->head, ring->tail,ATMEL_SERIAL_RINGSIZE )) { +dev_err (port->dev,"RX ring buffer full, dropping data\n" ); +/* Buffer overflow, ignore char */ return ; + } c = &((struct atmel_uart_char *)ring->buf)[ring->head]; c->status = status;
Hello Haavard,
Quoted 3 lines
It seems to be very sensitive to network traffic though...could it have something to do with softirq scheduling? Could you try the patch below and see if you can trigger the error message?
Funny that you mention this.
The largest latencies I currently have on RT (and rm9200) occur when using a telnet session or NFS filesystems, thus while using network. The impact on hardware Interrupt latencies are limited (<85us), so the interrupt handler should still be able to keep up the receive buffer, but context switches between threads can stall for a longer time under some conditions.
A long shot, but can it be that the ringbuffer overflows, and that therefor characters are lost?
Kind Regards,
Remy
Quoted 2 lines · On Thu, 31 Jan 2008 20:36:25 +0100 "Remy Bohmer" <[email protected]> wrote:
A long shot, but can it be that the ringbuffer overflows, and that therefor characters are lost?
That's what I was thinking too. If this is indeed the cause, the dev_err() added by the debug patch I posted should trigger and we may consider boosting the priority of the tasklet (using tasklet_hi_schedule.)
Other solutions may involve trying to figure out what exactly is blocking the tasklet from running. I have a patch series for the macb driver that optimizes the RX processing a bit, but it obviously won't help at91rm9200 since it uses a different driver...
Haavard
Hello Haavard,
Quoted 4 lines
That's what I was thinking too. If this is indeed the cause, the
dev_err()added by the debug patch I posted should trigger and we may consider boosting the priority of the tasklet (usingtasklet_hi_schedule.)
Notice that we are talking about Preempt-RT here. Everything is running in thread context, even tasklets, softirqs etc. They are _all_ preemptible, and if Michael has some RT-thread in the system that has a higher priority than this tasklet or softirq, than the buffer will eventually overflow.
I wonder also if Michael has set the RT-priorities correctly, on RT _every_ softirq/irq thread starts by default on priority 50, SCHED_FIFO. If they are still at 50, any other softirq/tasklet, or irq can make this behavior worse.
Notice that the default 50 thingy rarely gives a decent behaving system. (But any other default will also give problems anyway, so it _has_ to be customized/tuned by the end user)
Kind Regards,
Remy
Hi,
the serial driver works fine. The problem seems to be related to the tclib, when I use it as a clocksource. The numbers of overruns depends on the type of files too. It is possible?
Regards
Michael
Hello Michael,
Quoted 2 lines
the serial driver works fine. The problem seems to be related to the tclib, when I use it as a clocksource.
tclib as a clocksource should be no problem on Preempt-RT, do not use it as clockevent device, it will not work properly on preempt-rt on at91* yet, especially with the NO_HZ config.
Quoted 2 lines
The numbers of overruns depends on the type of
files too. It is possible?
I am still very curious to your (RT-) thread-prio layout. The problems you mention can also be caused by a weird configuration of these threads on preempt-rt.
Remy
2008/2/6, michael <[email protected]>:
Quoted 18 lines
Hi,
the serial driver works fine. The problem seems to be related to the tclib, when I use
it as a clocksource. The numbers of overruns depends on the type of files too.
It is possible?Regards
Michael--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Hi,
All works now for me with preempt-rt. The problem is using hrtimer.
I think that hrtimer are executed with interrupts disabled so, if this happen when I must receive a char, i have an overrun. The only solution was the dma support to serial device.
Regards Michael
Hello All,
Quoted 3 lines
All works now for me with preempt-rt. The problem is using hrtimer. I think that hrtimer are executed with interrupts disabled so, if this happen when I must receive a char, i have an overrun.
No, they share the same interrupt line...
So, while the timer interrupt handler is running, the serial handler has to wait until the timer interrupt handler has finished. Notice that the HRT interrupt handler is quite heavy and takes a long time to complete.
And, as I already mentioned, related to the 1 byte FIFO and a interrupt latency of about 85us (without HRT), it is logical that you can get an overrun at the higher serial speeds... (>=115200bps)
Quoted 1 line
The only solution was the dma support to serial device.
Or, use flow control?
Kind Regards,
Remy
Hi,
Quoted 10 lines · Remy Bohmer
Hello All,
Quoted 4 lines
All works now for me with preempt-rt. The problem is using hrtimer. I think that hrtimer are executed with interrupts disabled so, if this happen when I must receive a char, i have an overrun.
No, they share the same interrupt line...
I think that the hrtimer use and other interrupt line. The AT91SAM9260_ID_TC2.
Quoted 5 lines
So, while the timer interrupt handler is running, the serial handler has to wait until the timer interrupt handler has finished. Notice that the HRT interrupt handler is quite heavy and takes a long time to complete.
The problem is the heavy of HRT interrupt handler of course.
Quoted 5 lines
And, as I already mentioned, related to the 1 byte FIFO and a interrupt latency of about 85us (without HRT), it is logical that you can get an overrun at the higher serial speeds... (>=115200bps)
I don't have the same problem without the hrtimer, I suppose the the timer latency is not so heavy.
Quoted 7 lines
Quoted 2 lines
The only solution was the dma support to serial device.
Or, use flow control?
Yes :)
Michael
Hi
Quoted 12 lines
Haavard
drivers/serial/atmel_serial.c +0
-0@@ -337,9 +337,12 @@ atmel_buffer_rx_char(struct uart_port *port, unsigned int status,struct circ_buf *ring = &atmel_port->rx_ring;struct atmel_uart_char *c;
drivers/serial/atmel_serial.c atmel_buffer_rx_char(struct uart_port *port, unsigned int status, · line 348
Quoted 10 lines
drivers/serial/atmel_serial.c +4
-1-if (!CIRC_SPACE (ring->head, ring->tail,ATMEL_SERIAL_RINGSIZE )) +if (!CIRC_SPACE (ring->head, ring->tail,ATMEL_SERIAL_RINGSIZE )) { +dev_err (port->dev,"RX ring buffer full, dropping data\n" ); +/* Buffer overflow, ignore char */ return ; + } c = &((struct atmel_uart_char *)ring->buf)[ring->head]; c->status = status;
I have already tried that but I have never seen the buffer full. So tomorrow I can do other tests with the serial device. I think the the atmel_interrupt handler must check the pass_counter before return IRQ_HANDLED.
Regards Michael
Quoted 3 lines · On Mon, 04 Feb 2008 20:01:26 +0100 michael <[email protected]> wrote:
I think the the
atmel_interrupthandler
must check thepass_counterbefore returnIRQ_HANDLED.
I'm not sure if it helps in this particular case but yeah, since the interrupt may be shared, it's definitely wrong to always return IRQ_HANDLED.
Nice catch. Could you try the patch below?
Haavard
drivers/serial/atmel_serial.c +1 -1
@@ -552,7 +552,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id)atmel_handle_transmit (port, pending); }while (pass_counter++ <ATMEL_ISR_PASS_LIMIT ); -return IRQ_HANDLED ; +return pass_counter ?IRQ_HANDLED :IRQ_NONE ; }/*
hi,
Quoted 7 lines
drivers/serial/atmel_serial.c +0
-0
drivers/serial/atmel_serial.c static irqreturn_t atmel_interrupt(int irq, void *dev_id) · line 558
Quoted 8 lines
drivers/serial/atmel_serial.c +1
-1@@ -552,7 +552,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id)atmel_handle_transmit (port, pending); }while (pass_counter++ <ATMEL_ISR_PASS_LIMIT ); -return IRQ_HANDLED ; +return pass_counter ?IRQ_HANDLED :IRQ_NONE ; }/*
Just one question:
Receiving with hardware handshake works without PDC?
Regards Michael
Quoted 2 lines · On Tue, 05 Feb 2008 13:29:35 +0100 michael <[email protected]> wrote:
Just one question:
Receiving with hardware handshake works without PDC?
I don't know...I haven't tried. These patches shouldn't change anything though.
Haavard
Hi,
Quoted 11 lines · Haavard Skinnemoen
Quoted 3 lines · On Tue, 05 Feb 2008 13:29:35 +0100 michael <[email protected]> wrote:
Just one question:
Receiving with hardware handshake works without PDC?I don't know...I haven't tried. These patches shouldn't change anything though.
Quoted 8 lines
Haavard
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
I refer to this part of documentation:
"The USART behavior when hardware handshaking is enabled is the same as the behavior in standard synchronous or asynchronous mode, except that the receiver drives the RTS pin as described below and the level on the CTS pin modifies the behavior of the transmitter as described below. Using this mode requires using the PDC channel for reception. The transmitter can handle hardware handshaking in any case."
Regards Michael
Quoted 11 lines · On Wed, 06 Feb 2008 14:41:09 +0100 michael <[email protected]> wrote:
I refer to this part of documentation:
"The USART behavior when hardware handshaking is enabled is the same as the behavior in
standard synchronous or asynchronous mode, except that the receiver drives the RTS pin as
described below and the level on the CTS pin modifies the behavior of the transmitter as
described below. Using this mode requires using the PDC channel for reception. The transmitter
can handle hardware handshaking in any case."
Oh. I guess the answer is no, then.
Haavard