ICH5 with 2.6.1 very slow
Problem with ICH5?
I read the list web, so please CC my email, thanks.
P4 2.6G HT, 2GB Ram, ICH5, WD250GB/8M x 2 (md raid 1), kernel 2.6.1 Timing buffer-cache reads: 128 MB in 0.14 seconds =882.89 MB/sec Timing buffered disk reads: 64 MB in 2.14 seconds = 29.93 MB/sec
Celeron 1.3T, 1GB Ram, SIS630/5513, WD80GB/2M x 2 (md raid 1), kernel 2.6.1 Timing buffer-cache reads: 128 MB in 1.24 seconds =103.08 MB/sec Timing buffered disk reads: 64 MB in 1.83 seconds = 35.00 MB/sec
Celeron 2.5G, 512MB Ram, i845/ICH4, WD120GB/8M x 2 (md raid 1), redhat kernel 2.4.20
Timing buffer-cache reads: 128 MB in 0.35 seconds =365.71 MB/sec Timing buffered disk reads: 64 MB in 1.38 seconds = 46.38 MB/sec
Kyle
Quoted 7 lines · Kyle
Problem with ICH5?
I read the list web, so please CC my email, thanks.P4 2.6G HT, 2GB Ram, ICH5, WD250GB/8M x 2 (md raid 1), kernel 2.6.1 Timing buffer-cache reads: 128 MB in 0.14 seconds =882.89 MB/sec Timing buffered disk reads: 64 MB in 2.14 seconds = 29.93 MB/sec
Quoted 9 lines
Celeron 1.3T, 1GB Ram, SIS630/5513, WD80GB/2M x 2 (md raid 1), kernel 2.6.1 Timing buffer-cache reads: 128 MB in 1.24 seconds =103.08 MB/sec Timing buffered disk reads: 64 MB in 1.83 seconds = 35.00 MB/sec
Celeron 2.5G, 512MB Ram, i845/ICH4, WD120GB/8M x 2 (md raid 1), redhat kernel 2.4.20
Timing buffer-cache reads: 128 MB in 0.35 seconds =365.71 MB/sec Timing buffered disk reads: 64 MB in 1.38 seconds = 46.38 MB/sec
Is that a parallel IDE? I own a S-ATA IDE (also WD) with an ICH5. That performs around 45-50MB/sec with 2.6.1. I've never tried 2.4.xx on it.
Bas.
Yes they are PATA, I expect something like 40-50MB/s, now my much slower Celeron 1.3T with 80GB/2M perform better than my ICH5!
Kyle
----- Original Message -----
From: "Bas Mevissen" <[email protected]>
To: "Kyle" <[email protected]>
Cc: <[email protected]>
Sent: Friday, February 06, 2004 1:23 AM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 10 lines
Quoted 8 lines · Kyle
Problem with ICH5?
I read the list web, so please CC my email, thanks.P4 2.6G HT, 2GB Ram, ICH5, WD250GB/8M x 2 (md raid 1), kernel 2.6.1 Timing buffer-cache reads: 128 MB in 0.14 seconds =882.89 MB/sec Timing buffered disk reads: 64 MB in 2.14 seconds = 29.93 MB/sec
Celeron 1.3T, 1GB Ram, SIS630/5513, WD80GB/2M x 2 (md raid 1), kernel
2.6.1
Quoted 16 lines
Quoted 8 lines
Timing buffer-cache reads: 128 MB in 1.24 seconds =103.08 MB/sec Timing buffered disk reads: 64 MB in 1.83 seconds = 35.00 MB/sec
Celeron 2.5G, 512MB Ram, i845/ICH4, WD120GB/8M x 2 (md raid 1), redhat kernel 2.4.20
Timing buffer-cache reads: 128 MB in 0.35 seconds =365.71 MB/sec Timing buffered disk reads: 64 MB in 1.38 seconds = 46.38 MB/secIs that a parallel IDE? I own a S-ATA IDE (also WD) with an ICH5. That performs around 45-50MB/sec with 2.6.1. I've never tried 2.4.xx on it.
Bas.
Quoted 3 lines · Kyle
Yes they are PATA, I expect something like 40-50MB/s, now my much slower Celeron 1.3T with 80GB/2M perform better than my ICH5!
What does 'hdparm /dev/hdX' say (X=a,b,c...)?
Bas.
hdparm /dev/hda/dev/hda:
multcount = 16 (on)IO_support = 1 (32-bit)
unmaskirq = 1 (on)using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 30401/255/63, sectors = 488397168, start = 0
tried with hdparm -a8192 /dev/hda, not much different /dev/hdc same as /dev/hda
Kyle
----- Original Message -----
From: "Bas Mevissen" <[email protected]>
To: "Kyle" <[email protected]>
Cc: <[email protected]>
Sent: Friday, February 06, 2004 1:30 AM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 12 lines
Quoted 3 lines · Kyle
Yes they are PATA, I expect something like 40-50MB/s, now my much slower Celeron 1.3T with 80GB/2M perform better than my ICH5!
What does 'hdparm
/dev/hdX' say (X=a,b,c...)?Bas.
Quoted 11 lines · Kyle
hdparm
/dev/hda/dev/hda:
multcount = 16 (on)IO_support= 1 (32-bit)
unmaskirq = 1 (on)using_dma= 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 30401/255/63, sectors = 488397168, start = 0
Quoted 3 lines
tried with hdparm -a8192
/dev/hda, not much different/dev/hdcsame as/dev/hda
Looks fine. That's strange. Maybe reboot the system and check /proc/interrupts to see if none of them is excessive.
What's your .config? Try with as less as possible IDE stuff enabled.
Bas.
Today I tried to boot with redhat kernel 2.4.20-24.9smp, much better result:
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.14 seconds =914.29 MB/sec
Timing buffered disk reads: 64 MB in 1.67 seconds = 38.32 MB/sec
Really strange that /dev/hdc is even faster!/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.13 seconds =984.62 MB/sec
Timing buffered disk reads: 64 MB in 1.17 seconds = 54.70 MB/sec
I ran hdparm 5 times at both harddisk and take the fastest result. /dev/hda and /dev/hdc are both WD 250GB / 8M, same model.
at kernel 2.6, I got same performance for /dev/hda and /dev/hdc, around ~28MB/sec. 50%-100% slower then kernel 2.4
/proc/interrupt:
CPU0 CPU1
0: 8014632 0 IO-APIC-edge timer 1: 2273 0 IO-APIC-edge i8042 2: 0 0 XT-PIC cascade 8: 1 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-level acpi 14: 167888 0 IO-APIC-edge ide0 15: 199399 0 IO-APIC-edge ide1 20: 2186070 0 IO-APIC-level eth1 NMI: 0 0 LOC: 8014888 8014887 ERR: 0 MIS: 0
I tried to update my mobo BIOS (Intel D865GLC), remove one of the NIC (I have two), disable serial, parallel, USB etc just leave IDE and built-in display, no help. I have NO IDE cdrom and floppy, only 2 harddisk, 1 CPU, 4 x 512M DDR and a mobo at my machine.
CONFIG_IDE=yCONFIG_BLK_DEV_IDE=yCONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=yCONFIG_BLK_DEV_IDECD=mCONFIG_BLK_DEV_IDESCSI=mCONFIG_BLK_DEV_IDEPNP=yCONFIG_BLK_DEV_IDEPCI=yCONFIG_IDEPCI_SHARE_IRQ=yCONFIG_BLK_DEV_GENERIC=yCONFIG_BLK_DEV_IDEDMA_PCI=yCONFIG_IDEDMA_PCI_AUTO=yCONFIG_BLK_DEV_ADMA=yCONFIG_BLK_DEV_PIIX=yCONFIG_BLK_DEV_IDEDMA=yCONFIG_IDEDMA_AUTO=y
Kyle
----- Original Message -----
From: "Bas Mevissen" <[email protected]>
To: "Kyle" <[email protected]>
Cc: <[email protected]>
Sent: Friday, February 06, 2004 6:10 PM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 26 lines
Quoted 11 lines · Kyle
hdparm
/dev/hda/dev/hda:
multcount = 16 (on)IO_support= 1 (32-bit)
unmaskirq = 1 (on)using_dma= 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 30401/255/63, sectors = 488397168, start = 0Quoted 3 lines
tried with hdparm -a8192
/dev/hda, not much different/dev/hdcsame as/dev/hdaLooks fine. That's strange. Maybe reboot the system and check
/proc/interruptsto see if none of them is excessive.What's your .config? Try with as less as possible IDE stuff enabled.
Bas.
Quoted 1 line · Kyle
Today I tried
(...)
This is quite strange. The only thing I can think of is that the hardware (?) raid1 is causing problems with 2.6.
Is there a possibility for you to test without it?
Currently, I don't have a decent PATA disk luyng around, so I cannot verify anything for you.
Regards,
Bas.
No hardware raid, it's kernel built-in md driver.
----- Original Message -----
From: "Bas Mevissen" <[email protected]>
To: "Kyle" <[email protected]>
Cc: <[email protected]>
Sent: Monday, February 09, 2004 4:32 PM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 20 lines
Quoted 1 line · Kyle
Today I tried
(...)
This is quite strange. The only thing I can think of is that the hardware (?) raid1 is causing problems with 2.6.
Is there a possibility for you to test without it?
Currently, I don't have a decent PATA disk luyng around, so I cannot verify anything for you.
Regards,
Bas.
Today I tried with compile the kernel 2.6.1 with:
IGNORE word93 Validation BITS (IDEDMA_IVB) = y
The result looks a bit better, got 30MB/s at /dev/hda and 37MB/s at /dev/hdc (38MB/s and 55MB/s at kernel 2.4.20)
Still very strange, /dev/hda and /dev/hda are exactly same model harddisk.
Also, the result still can't compare with my another much slower machine Celeron / ICH4 / 2 x WD 120GB (md1), which got 46MB/s at both /dev/hda and /dev/hdc,
Kyle
----- Original Message -----
From: "Bas Mevissen" <[email protected]>
To: "Kyle" <[email protected]>
Cc: <[email protected]>
Sent: Monday, February 09, 2004 4:32 PM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 20 lines
Quoted 1 line · Kyle
Today I tried
(...)
This is quite strange. The only thing I can think of is that the hardware (?) raid1 is causing problems with 2.6.
Is there a possibility for you to test without it?
Currently, I don't have a decent PATA disk luyng around, so I cannot verify anything for you.
Regards,
Bas.
Quoted 6 lines · Kyle
Today I tried with compile the kernel 2.6.1 with:
IGNORE word93 Validation BITS (
IDEDMA_IVB) = yThe result looks a bit better, got 30MB/s at
/dev/hdaand 37MB/s at/dev/hdc(38MB/s and 55MB/s at kernel 2.4.20)
Aha...
Have a look at the thread called "[RFC] IDE 80-core cable detect - chipset-specific code to over-ride eighty_ninty_three()".
It specifically deals with ICH5 and is probably the same problem as you're seeing.
-- Jamie
Yes I read the thread and re-compile with IDEDMA_IVB= y, got some performance back, but is still far slower than 2.4
----- Original Message -----
From: "Jamie Lokier" <[email protected]>
To: "Kyle" <[email protected]>
Cc: "Bas Mevissen" <[email protected]>; <[email protected]>
Sent: Thursday, February 12, 2004 4:41 PM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 6 lines
Quoted 5 lines · Kyle
Today I tried with compile the kernel 2.6.1 with:
IGNORE word93 Validation BITS (
IDEDMA_IVB) = yThe result looks a bit better, got 30MB/s at
/dev/hdaand 37MB/s at
/dev/hdc
Quoted 12 lines
Quoted 1 line
(38MB/s and 55MB/s at kernel 2.4.20)
Aha...
Have a look at the thread called "[RFC] IDE 80-core cable detect - chipset-specific code to over-ride
eighty_ninty_three()".It specifically deals with ICH5 and is probably the same problem as you're seeing.
-- Jamie
Quoted 7 lines · Jamie Lokier
Have a look at the thread called "[RFC] IDE 80-core cable detect - chipset-specific code to over-ride
eighty_ninty_three()".It specifically deals with ICH5 and is probably the same problem as you're seeing.
Ive already pointed Kyle to that thread. But the udma settings seem to be OK.
So my guess now is that this is not just an issue with the driver only.
Regards,
Bas.
Another idea... check and make sure your hardware is set to "enhanced mode" in BIOS. "legacy mode" and "combined mode" would definitely be slow.
Jeff
It's already in "Enhanced mode", tried "legacy" and "combined" as well, no help.
----- Original Message -----
From: "Jeff Garzik" <[email protected]>
To: "Bas Mevissen" <[email protected]>
Cc: "Jamie Lokier" <[email protected]>; "Kyle" <[email protected]>; <[email protected]>
Sent: Friday, February 13, 2004 3:28 AM
Subject: Re: ICH5 with 2.6.1 very slow
Quoted 2 lines
Another idea... check and make sure your hardware is set to "enhanced mode" in BIOS. "legacy mode" and "combined mode" would definitely be
slow.
Quoted 7 lines
Jeff