Skip to contentSkip to conversation

cpufreq - less possible freqs with 2.6.2 and P4M

DISCUSSION Georg Müller 4 participants 5 messages Feb 7, 2004 – Feb 9, 2004

lore
Share & tools
lore
#0 lore raw

Hi,

I have a Pentium 4M at 1.8GHz.
With 2.6.0 it was possible to slow down my CPU in several steps down to 200MHz via cpufreq. With 2.6.2 I can only switch between 1.2 and 1.8GHz (as it was with 2.4 too).

Is this change wanted?

Georg Müller

#1 lore raw
Quoted 7 lines · Georg Müller

Hi,

I have a Pentium 4M at 1.8GHz.
With 2.6.0 it was possible to slow down my CPU in several steps down to 200MHz via cpufreq.
With 2.6.2 I can only switch between 1.2 and 1.8GHz (as it was with 2.4 too).

Which cpufreq module are you using? With p4-clockmod I get lots of choices, with acpi only the two you mentioned.

Signature · 2 lines
Måns Rullgård
[email protected]
#2 lore raw
Quoted 3 lines · Måns Rullgård

Which cpufreq module are you using? With p4-clockmod I get lots of choices, with acpi only the two you mentioned.

Ok, that works. With P4 clockmod only there are the freqs I wanted :-)

Thx,
Georg Müller

#3 lore raw
Quoted 6 lines · Georg Müller
Quoted 3 lines · Måns Rullgård

Which cpufreq module are you using? With p4-clockmod I get lots of choices, with acpi only the two you mentioned.

Ok, that works. With P4 clockmod only there are the freqs I wanted :-)

But I don't know it's having the effect you desire... :)

By monitoring /proc/acpi/battery/*/state ("present rate" key) I found that by using p4-clockmod at the lovest rate the processor permits, it's actually using more energy than by using speedstep_ich (only two levels of frequency).

I don't know if this is a bug of p4-clockmod or a hw bug in my machine though... can you please check in your machine?

Signature · 1 line
Cioby
#4 lore raw
Quoted 10 lines · Dumitru Ciobarcianu
Quoted 6 lines · Georg M??ller
Quoted 3 lines · M??ns Rullg??rd

Which cpufreq module are you using? With p4-clockmod I get lots of choices, with acpi only the two you mentioned.

Ok, that works. With P4 clockmod only there are the freqs I wanted :-)

But I don't know it's having the effect you desire... :)

Quoted 7 lines

By monitoring /proc/acpi/battery/*/state ("present rate" key) I found that by using p4-clockmod at the lovest rate the processor permits, it's actually using more energy than by using speedstep_ich (only two levels of frequency).

I don't know if this is a bug of p4-clockmod or a hw bug in my machine though... can you please check in your machine?

p4-clockmod offer only the possibility to throtte the cpu (and therefore you can get a kind of frequency setting when you change the duty cycle), but it do not scale voltage for the processor, whereas speedstep-ich will offer you the possibility to scale voltage and frequency by changing directly the core multiplier.

In fact, if you have at least power control for the processor via ACPI (look into /proc/acpi/processor/????/power), and your machine support at least the power state C2, and if you are using the p4-clockmod, or anything that do throttle the processor, you reduce the windows time when the processor can enter at least this C2 power state, and this may actually consume *more* power than you would expect, especially if the system is mostly idle.

Cheers,

Signature · 4 lines
Bruno Ducrot

--  Which is worse:  ignorance or apathy?
--  Don't know.  Don't care.