Skip to contentSkip to conversation

SCSI Tape (st) problem ....

DISCUSSION Nicholas Anderson 1 participant 1 message Apr 8, 2004

lore
Share & tools
lore
#0 lore raw

Hi All,

i'm using Slack 9 in a PIII machine with a DLT7000 tape drive, and kernel 2.4.25.

Everything was working fine before i changed my scsi disk.
Since then i've been receiving errors like this one below in my syslog, and my tape backup stopped working. The system didnt change (i made a disk mirror before changing it).

I'm trying to backup 2GB of data and im getting the error below in syslog and a "End of Tape" as the command output. The tape supports up to 70GB (with compression) i guess, and it was working 3 weeks ago ...
I tryed changing the tape but it still doesnt work.

As u kernel mantainers, r those who knows best this low-level problems, im sending u this email asking for help.

Any idea ?? Is it a hardware error ? Or only a module error ? Should i try to use "st" as fix instead of module ?

My SCSI tape:

Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: TANDBERG Model: DLT7000 Rev: 2151
Type: Sequential-Access ANSI SCSI revision: 02

My SCSI card/module:

Adaptec AIC7xxx driver version: 6.2.36
Adaptec 2940 Ultra2 SCSI adapter
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs

The syslog error:

Apr  8 11:09:15 backup2 kernel: (scsi0:A:4): 20.000MB/s transfers (10.000MHz, offset 15, 16bit)
Apr  8 11:49:11 backup2 kernel: scsi0:0:4:0: Attempting to queue an ABORT message
Apr  8 11:49:11 backup2 kernel: CDB: 0xa 0x0 0x0 0x2 0x0 0x0
Apr  8 11:49:11 backup2 kernel: scsi0: At time of recovery, card was not paused
Apr  8 11:49:11 backup2 kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
Apr  8 11:49:11 backup2 kernel: scsi0: Dumping Card State while idle, at SEQADDR 0x8
Apr  8 11:49:11 backup2 kernel: Card was paused
Apr  8 11:49:11 backup2 kernel: ACCUM = 0x0, SINDEX = 0xb, DINDEX = 0xe4, ARG_2 = 0x0
Apr  8 11:49:11 backup2 kernel: HCNT = 0x0 SCBPTR = 0x8
Apr  8 11:49:11 backup2 kernel: SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0] LASTPHASE[0x1]
Apr  8 11:49:11 backup2 kernel: SCSISEQ[0x12] SBLKCTL[0x6] SCSIRATE[0x0] SEQCTL[0x10]
Apr  8 11:49:11 backup2 kernel: SEQ_FLAGS[0xc0] SSTAT0[0x0] SSTAT1[0xa] SSTAT2[0x0]
Apr  8 11:49:11 backup2 kernel: SSTAT3[0x0] SIMODE0[0x8] SIMODE1[0xa4] SXFRCTL0[0x80]
Apr  8 11:49:11 backup2 kernel: DFCNTRL[0x0] DFSTATUS[0x89]
Apr  8 11:49:11 backup2 kernel: STACK: 0x83 0x166 0x10c 0x3
Apr  8 11:49:11 backup2 kernel: SCB count = 35
Apr  8 11:49:11 backup2 kernel: Kernel NEXTQSCB = 1
Apr  8 11:49:11 backup2 kernel: Card NEXTQSCB = 1
Apr  8 11:49:11 backup2 kernel: QINFIFO entries:
Apr  8 11:49:11 backup2 kernel: Waiting Queue entries:
Apr  8 11:49:11 backup2 kernel: Disconnected Queue entries: 13:31
Apr  8 11:49:11 backup2 kernel: QOUTFIFO entries:
Apr  8 11:49:11 backup2 kernel: Sequencer Free SCB List: 8 24 5 22 31 10 28 11 18 6 4 15 0 26 30 23 12 9 16 20 7 25 3 2 1 21 27 29 19 14 17
Apr  8 11:49:11 backup2 kernel: Sequencer SCB Info:
Apr  8 11:49:11 backup2 kernel:   0 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   1 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   2 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   3 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   4 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   5 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   6 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   7 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   8 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:   9 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  10 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  11 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  12 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  13 SCB_CONTROL[0x44] SCB_SCSIID[0x47] SCB_LUN[0x0] SCB_TAG[0x1f]
Apr  8 11:49:11 backup2 kernel:  14 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  15 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  16 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  17 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  18 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  19 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  20 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  21 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  22 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  23 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  24 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  25 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  26 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  27 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  28 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  29 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  30 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel:  31 SCB_CONTROL[0xe0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
Apr  8 11:49:11 backup2 kernel: Pending list:
Apr  8 11:49:11 backup2 kernel:  31 SCB_CONTROL[0x40] SCB_SCSIID[0x47] SCB_LUN[0x0]
Apr  8 11:49:11 backup2 kernel: Kernel Free SCB list: 11 20 16 28 29 2 4 0 12 24 25 15 7 26 13 14 33 34 22 18 5 3 9 32 21 6 27 19 23 17 8 10 30
Apr  8 11:49:11 backup2 kernel: Untagged Q(4): 31
Apr  8 11:49:11 backup2 kernel: DevQ(0:0:0): 0 waiting
Apr  8 11:49:11 backup2 kernel: DevQ(0:4:0): 0 waiting
Apr  8 11:49:11 backup2 kernel:
Apr  8 11:49:11 backup2 kernel: <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): Device is disconnected, re-queuing SCB
Apr  8 11:49:11 backup2 kernel: Recovery code sleeping
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): Abort Message Sent
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): SCB 31 - Abort Completed.
Apr  8 11:49:11 backup2 kernel: Recovery SCB completes
Apr  8 11:49:11 backup2 kernel: Recovery code awake
Apr  8 11:49:11 backup2 kernel: aic7xxx_abort returns 0x2002
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): data overrun detected in Data-out phase.  Tag == 0x1f.
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): Have seen Data Phase.  Length = 512.  NumSGs = 1.
Apr  8 11:49:11 backup2 kernel: sg[0] - Addr 0x08000 : Length 512
Apr  8 11:49:11 backup2 kernel: scsi0:0:4:0: Attempting to queue a TARGET RESET message
Apr  8 11:49:11 backup2 kernel: CDB: 0xa 0x0 0x0 0x2 0x0 0x0
Apr  8 11:49:11 backup2 kernel: scsi0:0:4:0: Command not found
Apr  8 11:49:11 backup2 kernel: aic7xxx_dev_reset returns 0x2002
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): data overrun detected in Data-out phase.  Tag == 0x1f.
Apr  8 11:49:11 backup2 kernel: (scsi0:A:4:0): Have seen Data Phase.  Length = 512.  NumSGs = 1.
Apr  8 11:49:11 backup2 kernel: sg[0] - Addr 0x08000 : Length 512

TIA

Nick

Signature · 6 lines
Nicholas Anderson
Administrador Linux/Unix
Rede Fiocruz
http://www.redefiocruz.fiocruz.br
e-mail: [email protected]
Tel:(21)2598-4499