problem with queue_task() and mark_bh()...
Hi there,
I have a problem with queue_task() and mark_bh().
In a driver for the wireless HERMES-II chipset I found the code snippets
/* Register the ISR handler information here... */
lp->task.routine = (void (*)(void *))wl_isr_handler; lp->task.data = lp;
printk("wl_isr_handler is @ %#lx\n", lp->task.routine);
At a later point (namely in the interrupt service rountine this happens:
/* If we have interrupts pending, then put them on a system task queue.*/
if( events == HCF_INT_PENDING ) {
/* Schedule the ISR handler as a bottom-half task in the
* tq_immediate queue
*/
printk( "Schedule the ISR handler %#lx...\n", lp->task.routine);
queue_task( &( lp->task ), &tq_immediate );
mark_bh( IMMEDIATE_BH );
}The problem is now that the queued task lp->task (i.e. wl_isr_handler) never get's called! And thus the driver does not work.
If I call the function directly using
lp->task.routine(lp);
instead of queue_task() and mark_bh() the function wl_isr_handler() gets called and the driver works.
Any idea why queue_task() and mark_bh() do not work as expected? How could I debug this problem?
(The two printk's show the same address.)
I am using linuxppc-2.4.25 from DENX CVS.
Thanks a million!!!
--
Steven Scholz
imc Measurement & Control imc Meßsysteme GmbH Voltastr. 5 Voltastr. 5 13355 Berlin 13355 Berlin Germany Deutschland
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi,
Quoted 15 lines · I wrote:
I have a problem with
queue_task()andmark_bh().
...
At a later point (namely in the interrupt service rountine this happens:/* If we have interrupts pending, then put them on a system task queue.*/
if( events == HCF_INT_PENDING ) { /* Schedule the ISR handler as a bottom-half task in the * tq_immediate queue */ printk( "Schedule the ISR handler %#lx...\n", lp->task.routine); queue_task( &( lp->task ), &tq_immediate ); mark_bh( IMMEDIATE_BH ); }
Quoted 2 lines
The problem is now that the queued task
lp->task(i.e.wl_isr_handler) never get's called! And thus the driver does not work.
When I call run_task_queue(&tq_immediate) right after mark_bh(IMMEDIATE_BH) then it works.
But I though "run_task_queue(&tq_immediate)" gets called by the kernel (after every timer interrupt)...
--
Steven Scholz
imc Measurement & Control imc Meßsysteme GmbH Voltastr. 5 Voltastr. 5 13355 Berlin 13355 Berlin Germany Deutschland
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi,
Quoted 2 lines
Quoted 2 lines
queue_task( &( lp->task ), &tq_immediate ); mark_bh( IMMEDIATE_BH );
I've put some printks in my kernel.
Now I can see that the task is successfully queued, that mark_bh() is called and the tasklet_hi_schedule() calls __tasklet_hi_schedule().
But the function immediate_bh() in kernel/timer.c (which should then call run_task_queue(&tq_immediate)) is never called.
Any ideas?
Steven
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/